Search Documents

By A Llewellyn, M Varvari

The ventilation circuit at the FrogÆs Leg Mine was originally designed to permit mining to progress down to 440 m below surface at a maximum production rate of 500 kt/a, as per the feasibility study. The FrogÆs Leg resource has now been defined down to 640 m below surface at a maximum production rate of 750 kt/a. In order to allow for this increase in production depth and tonnage, it was necessary to upgrade the ventilation circuit.This paper outlines the upgrades to the ventilation circuit that were undertaken and the underlying rationale behind them.CITATION:Llewellyn, A and Varvari, M, 2013. Ventilation upgrade at the FrogÆs Leg Mine - Case study, in Proceedings The Australian Mine Ventilation Conference , pp 95-102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Matthias Neuenschwander, Andreas Theiler, Patrick Steinle, John Singer, Martin Vogel, Diego Martini, Ömer Ündül, Markus Weh

"Quartz Dust is a major health hazard in underground works, wherever the ground contains quartz and depending on the chosen method of excavation. A research project initiated by the Swiss Tunnelling Society and realized by the Swiss Federal Institut of Technology, Zurich, established a correlation between the potential of quartz dust generation during excavation and well known geotechnical characteristics – the Cerchar Abrasivity Index CAI and the Uniaxial Compressive Strength UCS - of ten typical Swiss rocks. The results are at the center of a new guideline by the Swiss Society of Engineers and Architects on the requirements for early project stages regarding ventilation and logistics in function of the quartz dust related risk of the expected ground type of the project. The approach presented could be applied worldwide, contributing to more effective health protection as well as to better cost stability in underground works. CONTEXT Respirable quartz dust (aerodynamic diameter of particles < 10 micron) is universally recognized as a major workplace health hazard. Chronic bronchitis, silicosis and lung cancer can be caused by excessive exposure to quartz dust, as has been proved by many medical studies. Therefore, the legislations of many nations specify a maximum workplace concentration (Maximale Arbeitsplatzkonzentration MAK, Occupational Exposure Level OEL). In Switzerland, for example, the Threshold Limit Value TLV for respirable Quartz or Crystalline Silica imposed by the Federal Committee on Exposure Levels (Grenzwertkommission) is 0.15mg/m3 air. Some nations refrain from establishing a OEL because of the carcinogenic nature of quartz."

Jan 1, 2016

By E. Kumar, L. A. Kumar

"A methodology is proposed to develop an optimization model to understand the impact of transporting minerals, from mines to the final destination, on air quality. Recently, there has been increasing concern about the combined effects of multiple activities over many years, and the regional environmental changes brought about by a single project. Environmental issues in the iron ore industry have highlighted the need to broaden the cumulative impact assessment. In this study, we simulated the optimal routes and quantity of materials needed to meet the destination plant demand based upon environment constraints (level of air pollution), as well as the cost of transportation and availability of materials. Multiple scenarios were developed to analyse the effects of changes in routes, alternative transport system (or multi-modal split), traffic congestion, and the cumulative impacts on air quality. The air quality impact zones of the study area were demarcated using a GIS technique. The expected outcome of the study is the selection of a suitable transport system for a particular site with the least impact on air quality, including the transportation route, relative to the minimum cost of transportation of the minerals from the mines to their final destination. The proposed methodology is evaluated with a case study. IntroductionIn India, the process of environmental impact assessment (EIA) has been focused primarily on the local impacts of projects, without considering regional environmental effects. Environmental clearances for proposed projects are based on reports of local impacts. However, any developmental project poses a potential risk to the environment as a whole, and not just in the immediate vicinity of the project. Recently, there has been increased concern about the combined effects of multiple activities over many years—the regional environmental changes due to development of a single project (Dutta, Mahatha, and De, 2004). Environmental issues throughout the country, particularly in the iron ore industry, have emphasized the need to broaden the analysis to include the combined impacts, or those forecast for a proposed region, on an existing environment. The most significant adverse environmental consequences of iron ore transportation are the deterioration of biodiversity and air quality (Kumar and Ajay, 2015)."

Jan 1, 2017

By C. J. Hartley

"Scandium oxide can be recovered as a by-product from process streams in a number of chemical and metallurgical plants including TiO2 sulphate pigment, Ni/Co laterite, zirconium oxychloride and uranium operations. The feed materials available for processing can be either mid or end of process streams containing many species in solution. This paper describes the strategies available to limit coextraction of elements into scandium containing streams from TiO2 pigment production and the removal of these elements to deliver high purity scandium oxide.A critical part of process development is to work within the constraints of the main process in terms of introducing new unit processes and producing minimal additional process intermediates and residues. This requires flexibility in designing flowsheets and plants to find novel process routes that avoid production of intermediates and/or the introduction of reagents that can compromise the main process operations.Bloom Energy has developed novel solvent extraction processes for the extraction and refining of scandium oxide that minimise impacts on core process streams within TiO2 pigment plants. The additional unit processes are designed to have minimal contact with pigment plant process streams to produce a concentrate that is refined to nominal 3N purity scandium oxide in a simple, small scale commercial plant."

Jan 1, 2016

By J. A. Madonna

Independent prospectors and small to large-scale exploration company personnel have requested, and are in need of, guidance in geochemical field sample collection methods which will provide the most reliable results during chemical analysis. In cooperation with analytical laboratories, experienced geochemical exploration scientists and mining companies a systematic collection procedure has been developed. The procedure consists of collecting uncontaminated, water, sediment and rock chip samples of the appropriate quantity and/or dimensions to meet the needs of analysis.

Jan 1, 1999

By Earl L. Hastings

Although the principal market for diatomite in the United States is in the East,4 production of the material is presently restricted to the West, because the deposits are larger, mining costs are cheaper, and the quality of product is better than that obtained from other domestic deposits. However, Tallahatta diatomite, occurring in Choctaw and Clarke Counties, Ala., has a freight rate advantage, which should encourage competition for those market that are now being supplied with the purer diatomites from the western deposits. For this reason, diatomite occurrences in the Tallahatta formation were examined by the Bureau of Mines and physical properties of samples from the deposit were determined to obtain additional data for use by any potential producer who wished to evaluate the material for its commercial possibilities. In 1894 K. M. Cunningham5 found that the buhrstone formation (now known as the Tallahatta formation) contained "siliceous shells of marine diatoms, radiolaria and foraminifera, thus being rather of the nature of tripoli or diatomaceous earth than of a true clay." Cooke6 and Semmes7 also reported the Tallahatta formation to be composed principally of diatomaceous earth with accompanying beds of sand, clay, and sandstone.

Jan 1, 1963

By Jan Kvinge, Aina Opsal Bakke, Yanjun Li, Jan-Ove Løland, Svein Jørgensen

"Compound casting is a very attractive approach to reduce the weight of components for some specific applications while keep both the functional and the mechanical property requirements. In this work, Al-7Si-Mg alloy /copper compound castings were produced through a low pressure die casting process. To reduce the oxide present in the interface, flux coating of the copper pipes was tested. The interface layer formed between the two alloys was investigated using Optical Microscopy (OM), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Vickers Micro-hardness was also measured across the interface. Results showed that the flux coating prevented the formation of the metallic bond between copper and aluminum. Instead, high concentrations of potassium, magnesium and fluoride, coinciding with formation of KMgF3 and MgF2, were detected in the interface. In the castings without surface treatment, a continuous metallurgical bond was achieved. In the bond layer, various Al-Cu intermetallic phases have been detected. In addition, formation of primary silicon particles in the reaction layer was observed in all castings. The mechanism for the formation of the intermetallic phases and the strength of the interface layer have been discussed.INTRODUCTION Recent development in the automotive industry has focused on producing lightweight components, which can reduce CO2 emission and increase the efficiency. Often, one material alone is not able to meet the requirements for a specific use. The need for lightweight bimetallic components has therefore increased. Aluminum-copper bimetallic components can be used in wires and bus bars where conductivity is an important factor (Lee, Bang, & Jung, 2005). Compared to Al-Cu alloys, Al-Cu bimetallic components can reduce both weight and cost without reducing electrical and thermal conductivity (Sheng, Yang, Xi, Lai, & Ye, 2011). A challenge is, however, that aluminum and copper have high affinity to each other, especially at elevated temperatures. This causes formation of brittle intermetallic phases with high electric resistance (Liu, Wang, Sui, Wang, & Wenjiang, 2016). In addition, both metals are subjected to oxide formation on the surface. Copper is especially exposed to oxidation at elevated temperatures (Pinnel, Tompkins, & Heath, 1979), while a thermodynamically stable oxide layer will spontaneously form on the aluminum surface (Papis, Loeffler, & Uggowitzer, 2009). Oxides are known to be passive substrates, which will reduce wettability and will thus prevent the formation of metallic bonding between aluminum and copper (Papis, Hallstedt, Löffler, & Uggowitzer, 2008)."

Jan 1, 2018

By Kevin J. Ma, John Stankus, Dakota Faulkner

"Expandable rock bolts are widely used in hard rock mines as an efficient ground control product. However, capacity and service life can be significantly reduced if the metallic body is subjected to corrosion. In some hard rock mines in the U.S., highly corrosive ground conditions exist, and it has been reported that inflatable rock bolts have corroded within a few months after installation. To provide mining industry a cost-effective inflatable bolt and combat the corrosion issues, Jennmar Corporation, Inc., and its subsidiary Keystone Mining Services, LLC (KMS), analyzed corroded bolt samples, identified root causes, evaluated properties of various coating materials, and developed a new inflatable rock bolt, Python M3TM, that is protected with an innovative PyFlexU2TM coating. The new generation Python M3 features improved steel chemistry for reliable performance, modified profile for better inflation, and surface preparation and coating application. The PyFlexU2 is impervious to liquid and air, durable, and UV resistant. With a flexible adhesive, and highly corrosion-resistant undercoating, and a very hard sacrificial surface coating, the PyFlexU2 coating system provides the Python M3 superior protection against chemical corrosion and physical scratch damage. The under-coating has exceptional flexibility and adhesion to prevent coating micro-cracks or fractures after bolt inflation and possesses excellent corrosion resistance to acids (pH <3), alkalis (pH >11), fuels, and salt solvents. The corrosion and scratch resistant PyFlexU2 coating offers very effective bolt protection for extra longevity in highly corrosive environments. The Python M3 coated with PyFlexU2 has been tested in the most challenging conditions, including laboratory corrosion tests in extreme acidic and basic solvents, rock slurry, and borehole scratch insertion tests. With demonstrated corrosion and scratch resistance, the product has been greatly welcomed by hard rock mines in the West and is currently installed in large scale. This paper identifies the root causes of the bolt corrosion, discusses the analysis process, and details laboratory and underground tests carried out on the Python M3 coated with PyFlexU2. The Python M3TM and PyFlexU2TM are subjects covered by pending U.S. Patent Applications assigned to FCI Holdings Delaware, LLC."

Jan 1, 2017

By M. Kuyumcu

After German reunification the mining industry in former East Germany was profoundly restructured. Beside privatization of profitable companies the public sector took over responsibility for the mining operations to be shut down. Therefore state-owned companies cope with technical, ecological, and social challenges. The rehabilitation and reclamation has to rededicate former mining areas to new use and provided new jobs as well. In the lignite mining districts there are around 100,000 ha of mining area, a mining caused disturbance to the groundwater balance and to the system of surface water bodies of approx. 390,000 ha. They are called the largest landscape construction site in Europe. In addition to the results and diverse experience achieved over the past 23 years, a description will follow of our new challenges and of an outlook on remaining tasks. This article will describe the financing, as well as aspects of the jobcreation policy arising from lignite industry remediation.

Aug 1, 2013

By H. L. Lovell

The growing production of fly ash with the many attendant problems of economics, disposal and potential uses suggests an urgent need to consider those properties which are basic in its beneficiation. Fly ash is extremely variable and heterogeneous in all respects except its fine size. Because of its production in huge quantities, it becomes significant as a potential raw material. Detailed data are presented describing particle size and shape, density distribution and magnetic characteristics. The major components include combustible residuals, magnetite and silicates. These data are discussed in terms of beneficiation processes and uses, The results of air classification to produce a uniformly fine-sized low combustible product are encouraging. It is proposed that major increases in the future use of fly ash, must involve some form of beneficiation. Both the coal producing industries and the consuming utilities would benefit from increased utilization.

Jan 1, 1964

By T. Imgrund, A. Bischoff, S. Spürk

"Specific conditions of underground coal mines at great depth, such as high temperatures, high rates of methane inflow and natural ventilation pressure provide considerable challenges for the reliable design of appropriate mine ventilation systems. For decades coal mining in Germany has coped with these extreme circumstances. Based on these experiences appropriate software tools for simulating mine ventilation networks have been developed and continuously enhanced. This paper examines differences in the simulation results and underlying calculation methods of two software solutions. The analysis is based on the comparison of FlowNetTM and VentSim DesignTM (Version 5.1) regarding the accurate prediction of fluid mechanical quantities and their validation with real measurements. A special focus lies on exceptional ventilation scenarios typical for deep coal mines, like gas inflows, fire events and buoyancy effects. The purpose of the comparison is the future utilization of the experiences gained during mining at up to 1,500 m depth for state of the art ventilation design. INTRODUCTION Ventilation is an essential component of mine operations—as providing fresh air to workplaces, diluting and removing explosive, toxic or asphyxiating pollutants and assuring sufficient climate conditions. On the other hand, the costs of ventilation contribute to a large extend to the overall operating costs of a mine, as the share in the energy consumption of a mine may be in the range of 25–50% (Belle, 2008). Accordingly, proper design of ventilation systems has been a task since early times. Consequently software for modelling of ventilation networks has been developed in order to improve efficiency and accuracy of calculations (Maleki, 2018). Compressible flow has not been considered by initial ventilation modelling software tools. In Germany, the consideration of changes in airflow density—depending on pressure and temperature—in the algorithms of ventilation simulation software has been started in 1974 by Duepre & Hofbauer. This development had been continued by the Pruefstelle fuer Grubenbewetterung (Test Centre for Mine Ventilation) and resulted in the release of a computer ventilation software named “Wetter”. The mine inspectorate of the German state of North Rhine-Westphalia, which supervises the major coal mining district in Germany, declared ventilation simulation based on compressible flow being “state of the art” in 1985 (Pollak, 1985). This pronouncement made allowance for assessing the consequences of underground fires and downtimes of main fans based on advanced software solutions."

Jan 1, 2019

By Hillary W. St. Clair

Reaction rate coefficients were determined from analyses of the effluent gas for the reduction of granular ferrous oxide to metallic iron by passing carbon monoxide through a packed bed of oxide at a controlled rate in the temperature range 1,000° to 1,300° C. Coefficients were determined by the comparison of observed analyses and calculated analyses using a mathematical model that takes into account the nonuniform composition of both the solid oxide and the gas. A method is also given for finding the value of the rate coefficient that best fits the observed data.

Jan 1, 1968

By K. E. Tame

The Bureau of Mines is studying possible modifications in conventional uranium ore-processing steps to confine and permit controlled disposal of radioactive wastes. Surveys of Ra226 contamination of liquid wastes from uranium mills indicated that the Vanadium Corporation of America plant at Durango, Colo., had one of the more urgent problems. A possible procedure for minimizing the waste disposal problem was to reuse the waste solution in the mill--in effect, erasing the need for disposal of liquid waste. In examining this possibility, interlocked bench-scale leaching and solvent extraction tests simulating the Durango flowsheet were made. The simulated reuse of barren raffinate for leaching and washing was carried through three separate campaigns of 9, 12, and 35 cycles each.

Jan 1, 1961

By Jr. Babcock

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd., in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain Ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 kilometers. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fibre in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd. Of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This paper will present the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits will be outlined. Subsequent work by other companies will be mentioned, but not described in any detail. This subsequent work did not alter Kennecott&apos;s conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd., who have been involved in the project, particularly Ramon Farmer, N. G. Comer, and A. W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this report are solely that of the author and result from his involvement in discovery of the deposits and management of the exploration program.

Jan 1, 1978

By Yosry Attia

Recent emphasis on environmental effects and costs of conventional mining processing, plus success in accelerating bacterial action, suggest that biotechnology be explored for gold ore processing. In our paper, the past experience with organisms in processing gold is reviewed. The use of microorganisms for liberation of gold from sulfide ores as a substitute for fine grinding is discussed. The possibility of accumulation of gold from solutions, such as cyanide solutions, is explored as a potential replacement for such processes, such as carbon-in-pulp or ion exchange. The improvement in engineering technology and kinetics needed to scale-up from laboratory experiments to production scale are outlined.

Jan 1, 1985

By I. Yelkin, Erico Tabosa, Alex Jankovic, R. Hayashida, R. Faveere

"The mining industry faces growing challenges from more complex and lower grade deposits, rising costs, limited energy and water availability, and increasing societal pressure to operate more sustainably. Mining operations need to be more efficient, not just to reduce environmental impact, but also to remain economically viable.To maximize profitability and sustainability, existing operations and new projects must consider integration and optimization of all stages of production. A mining operation is essentially a series of inter-connected processes, with the performance and outputs of each stage affecting the subsequent ones. Optimizing stages in isolation can result in sub-optimal overall performance.The industry has long recognized the benefits of holistic optimization using the Mine-to-Mill concept, and there are many well documented successes. However, it is increasingly common to observe operations simply increasing explosive consumption in the mine and expecting optimization of the entire value chain (mining and processing). For true holistic optimization, blast intensity is not necessarily increased, but rather adjusted to best suit the requirements of the different types of ores treated, the circuit configuration and equipment, installed comminution power and the downstream beneficiation processes. It is a fully integrated effort with optimization of many aspects in the mine, comminution and separation processes.To be successful, optimization of the production chain from mine to process requires a site-specific, structured methodology supported by extensive ore characterization, auditing, surveys, data analysis, mathematical modelling simulations and a cost / benefit analysis. Following this methodology, optimization strategies are rapidly identified and implemented considering mine and plant constraints. Management needs to set up appropriate KPIs and site personnel need to be trained for the new operating strategies to be successfully incorporated into site practices and procedures in the production environment. This will ensure the benefits are achieved and maintained. This paper describes the methodology employed by Hatch to improve overall efficiency and profitability from mine to process. Two case study examples at Russian gold operations and benefits achieved are presented."

Jan 1, 2018

By Thomas V. Falkie

The title of this talk has brought some interesting responses - even before it was written - from different parts of the country. A geologist from the Western U. S, was deeply concerned with recent layoffs in his profession and the employment situation in general and wondered why "the AIME wasn&apos;t doing anything for the benefit of its members." A petroleum engineer in Texas said that a group in his field were studying "professionalism" and their professional status and wondered if there were any words of wisdom for him. A mining engineering professor from the East pointed out that the National Science Foundation did not include mining engineering as one of its recognized fields in one of its equipment funding programs. These are just a few examples of reactions received to date, but they serve to illustrate the broad image that the title has meant to various people. Actually the term profession is defined by Webster as "a calling requiring specialized knowledge and often long and intensive academic preparation." The word encroach means "to enter by gradual steps or by stealth into the possessions or rights of another", or "to advance beyond desirable or normal limits." The intention of this paper, as originally conceived and requested by the program chairman, was to combine those two words literally and talk about how the professional standing of mineral engineers is being eroded from people outside the profession. But the amazing preliminary response suggests that it may be timely to broaden the discussion by including some comments about professionalism in general. In the paper the terms "mineral engineer" or "mining engineering" are used frequently, but it should be clearly understood that much of what is said is valid and is intended for all fields covered by SME and perhaps for AIME in general.

Jan 1, 1972

By J. G. Croeni

The high thermal-neutron cross section of gadolinium and the good mechanical and corrosion properties of titanium suggest that alloys of these two metals might be useful as control rod material. To aid in establishing the feasibility of this combination, the Federal Bureau of Mines investigated the titanium-gadolinium system. The results indicate that the system is composed of a single eutectic reaction and a peritectoid reaction involving the alpha-beta transformation of titanium. The eutectic isotherm extends from 1 to 99 pct, gadolinium at 1,240° C. The established eutectic composition is about 95 pct, gadolinium. The peritectoid reaction occurs at 885° C. and extends almost over the entire composition range. Hardness increases slightly with additions of gadolinium, and little change is obtained by heat treatment. Alloys containing less than 10 pct. gadolinium are amenable to extensive cold-working, but alloys having higher percentage of gadolinium content are only moderately cold-workable. All alloys can be hot-worked in iron sheathing at 750° C. Observation indicates that all compositions possess good machinability. Corrosion resistance to water at room temperature is apparently poor, especially in the gadolinium-rich alloys. INTRODUCTION A combination of the good mechanical and corrosion properties of titanium and the variety of thermal-neutron cross sections characteristic of the rare-earth metals suggests that alloys of these metals may be used for control rod materials. For this reason the Bureau of Mines proposed a study of the titanium-gadolinium alloy system, and the Atomic Energy Commission sponsored the investigation.

Jan 1, 1961

By Haydn H. Murray

Kaolin is defined and described as an industrial mineral. In addition the types of deposits -primary and secondary are defined and the genesis of kaolin from feldspars and other minerals discussed. The major deposits of the world found in the United States, Great Britain, Brazil, and Czechoslovakia are described along with many of the minor kaolin deposits. Four areas which have very large deposits of kaolin could, with technological breakthroughs to reduce viscosity significantly, become important factors in supplying the world markets which are increasing year by year.

Jan 1, 1977

By V. Labiouse, M. Souley, N. Lafrance, C. Auvray

"Chalk rocks have been used for centuries as a strong building material and for the production of lime. The shallow underground room-and-pillar quarries where the chalk was extracted are now abandoned and endure the effects of time and weathering, increasing their risk of collapse. The risk of instability, involving natural or anthropic underground structures, is an issue for more than 10 000 towns in France.In order to investigate the causes of underground quarry collapse and to aid prevention strategies, we carried out a study of the physico-mechanical behaviour and ageing of chalk in abandoned pillars in two underground quarries, in situ-instrumented by INERIS, in the Parisian Basin, France. Core samples were drilled horizontally from pillars in the Saint-Martin-Le-Noeud dolomitic chalk quarry (Oise, France) and the Estreux glauconitic chalk quarry (Nord, France).Uniaxial tests were performed on dry and saturated cylindrical plug samples extracted perpendicular to the cores at regular distances along their lengths. Physical and mechanical properties were obtained. The dolomitic chalk (Saint-Martin-Le-Noeud) exhibits variation in mechanical and physical properties with horizontal pillar depth. Both density and compressive strength seem to increase outwards from the pillar-core to the pillar-wall. This is the opposite of that would be expected from a purely mechanical point of view. SEM analysis revealed progressive degradation and homogeneity of the grains from the edge to the inside of the pillar. At the pillar wall, the crystal faces are well-defined, almost euhedral, and the grains are of variable size. In contrast, at the inside of the pillar, crystals are finer-grained and are anhedral with highly degraded edges. In the physico-mechanical tests and SEM analyses performed on the Estreux samples, no significant variation was observed between the pillar-walls and pillar-core. However, dissolution marks were observed along the entire length of the half-pillar core."

Jan 1, 2015