Search Documents

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Roller presses are widely utilized in mineral industry for fine milling and compaction. Recently used models are providing only limited information about the material behavior in the roll bite. This paper introduces a 2-dimensional finite element model for analyzing those two basic processes. A pressure-dependent plasticity model with linear elasticity was used as a constitutive model for the particular material. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Two basic roller geometries are considered: smooth (used for milling and compaction) and with cavities, commonly used for briquetting. Comparison of the results obtained from the model with experiment indicates that they are following the general trends of experimental values recorded with laboratory roller presses. It is shown, that the model is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables. This allows the process engineer to gain an improved understanding, leading to a better process and equipment design and control.

Jan 1, 2003

By Thomas Leonard Watson

SULPHIDE ore-bodies of more or less lenticular shape occurring in metamorphic crystalline schists, gneisses, and. slates, and conforming closely in strike and usually in dip to the inclosing rock, have been recognized and described along the, Atlantic seaboard from Quebec to Alabama. The ore-bodies do not entirely conform, in all cases, to the structure of the inclosing schists, but they sometimes cut across the foliation in dip, though conforming more closely with the direction of strike. In composition the principal sulphide mineral is usually pyrite or pyrrhotite; or both, accompanied by copper, frequently gold, and almost always some sphalerite and galenite. Other. metallic ores are, so far as these sulphide bodies have been investigated, less common; silver is not uncommon, and in some of the pyrrhotite masses nickel is present in quantity sufficient to be commercially valuable. Cobalt frequently accompanies .the nickel, usually in smaller amount, and the two vary much in relative proportion. Quartz and calcite are probably the most common of the, non-metallic minerals. A number of silicate minerals are frequent representatives in one place or another; garnet, amphibole, biotite, pyroxene, zoisite and others. The sulphide bodies of Virginia, comprising both pyrite and pyrrhotite, are among the most extensive along the Atlantic seaboard. Among the pyrite bodies may be mentioned the well-known and extensively worked mines of Louisa and Prince William, counties, located on' the main pyrite belt (A, Fig. 1) of the middle and northern, eastern Piedmont region in Virginia, and among the pyrrhotite bodies is the famous " Great Gossan Lead "(B, Fig. 1) of the Floyd-Carroll-Graysou coun-

Sep 1, 1907

By Charles Will Wright

MINERAL production in almost all European countries suffered a sharp setback because of the war. Plants were damaged, transportation facilities disrupted, and labor dispersed and demoralized. Since the war, due to lack of confidence and economic stability, there has been little incentive to rebuild and expand the mineral industries even though a big demand at high prices exists for mineral products. Most mining and metallurgical companies in Europe hesitate to invest their capital because of the tendency towards nationalizing industry, high taxes, and low output of labor, as well as the deficiency of mine supplies and equipment within their countries. In short, they do not have faith in the future, and for these same reasons and fears most of the mining companies in America will not risk capital investment in Europe. In Europe, including the United Kingdom, free enterprise has been losing ground and as a result the foundation of their economic welfare is being undermined. American mining interests willing to take the initiative could help in counteracting this influence if a way were found for them to co-operate with the European producer without too great a risk.

Jan 1, 1948

By William R. Adamson

This paper describes some of the results of previously unpublished research studies conducted in underground operations in Chile and Australia, where cross-hole seismic measurement profiles were interpreted in terms of dynamic modulus. This work dates from a period between 1987 and 1990 and the Author suggests that 30 years on, applying modern day technology, instrumentation and modelling methods, more meaningful, practical and applicable results may be obtained.

Feb 1, 2020

By AIME AIME

SECOND only to the February Annual Meeting of the Institute are the Regional and Divisional meetings held in the fall of each year. Six such gatherings are scheduled in the next the months, with something likely to interest every member of the Institute. A brief résumé of the programs follows. Regional Meeting Vancouver T HE regional meeting of the Institute will be held at Vancouver, Sept. 13 to 20, in conjunction with the annual western meeting of the Canadian Institute of Mining and Metallurgy. The pro gram appeared on page 350 of MINING AND METALLURGY for July and-proof of careful preparation-a month later re- quires no correction and little elaboration. On the technical side there are few changes. A new item on the Wednesday morning program is the paper, "Investigation of Residential-type Stokers," by H. F. Yancey, supervising engineer, Northwest Experiment Station. U. S. Bureau of Mines, Seattle. As to entertainment the meeting is taking on some most pleasurable aspects. Two notable excursions have been arranged.

Jan 1, 1937

By E. J. KENNEDY

METHODICAL AND EFFECTIVE: thus may be characterized the fall meeting of the Iron and Steel and Institute of Metals Divisions at the Hotel Statler, Buffalo, N. Y., on Oct. 4 and 5. Approximately 200 registered. Interest centered 1111 the technical papers which were keenly followed, with substantial discussion: During the entire week of the National Metal Congress (Oct. 3 to 'i), there were also other sessions of interest' to metallurgists, directed by the America11 Society for Steel Treating, American Welding Society, Production Division of the Society of Automotive Engineers, the Iron arid Steel and Machine Shop Practice Divisions of the American Society of Mechanical En,' the Wire Association and the American Drop Forging Institute. The National Metals Exposition at the 174th Regiment Armory was well attended.

Jan 1, 1932

By F. William Bloecher, William B. Plank

CURRENTLY 12,892 students are enrolled in the mineral engineering schools of the United States and Canada, marking an all-time record high for these schools. It shows a remarkably rapid recovery from the effects of World War II. Enrollment in all the other engineering branches has also increased but not so rapidly as in the mineral engineering branch. Almost all the data in this report are from the eighth questionnaire study of the mineral engineering schools made, as formerly, under the auspices of the Mineral Industry Education Division of the AIME. Every school is represented in the data, for which the authors thank the deans and professors who supplied the information. For this reason, the data of all the studies are comparable, an achievement not always possible in endeavors of this kind. For comparison with the general engineering enrollment situation, data are included from the January 1947 issue of the Journal of Engineering Education.

Jan 1, 1947

By Arlindo Lopes Faria

O Drop Weight Tear Test (DWTT) é comumente empregado para avaliar a capacidade de um material impedir a propagação de fratura frágil na temperatura de projeto. Esse ensaio quando aplicado a aços modernos de elevada tenacidade, produzidos via resfriamento acelerado, para aplicação em dutos, pode não exibir o mesmo comportamento à fratura dos aços convencionais, por apresentar um tipo de fratura anormal, denominada fratura inversa. Esse tipo de fratura, por sua vez, invalida os resultados de DWTT segundo os critérios estabelecidos pela API RP 5L3. Neste trabalho, são apresentados os resultados obtidos em ensaio de DWTT, utilizando corpos de prova full-size e sub-size, de um aço de elevada tenacidade, produzido com distintas condições de processamento termomecânicas evidenciando o fenômeno de fratura inversa. De uma forma geral, observou-se uma correlação entre os resultados de DWTT e as propriedades mecânicas em tração. Os testes também apontaram que a geometria do corpo-de-prova (full-size ou sub-size) possui uma influência direta no resultado do ensaio de DWTT.

Aug 16, 2017

By Alessandro de Castro Corrêa

A comparação de processos de soldagem é uma tarefa complexa por envolver diversos atributos. A designação dos pesos dos atributos a serem avaliados é uma etapa fundamental na análise de problemas multicritérios; contudo, por vezes, a única informação que se obtém é a ordem de prioridade. O objetivo deste trabalho foi calcular os pesos das propriedades destinadas à comparação de processos de soldagem em aço inoxidável AISI 316L para o reparo de eixo naval com base na ordenação fornecida pelo tomador de decisão. Os atributos considerados foram taxa de deposição, energia de soldagem, rendimento econômico, diluição e relação reforço-largura. Os métodos de atribuição de pesos aplicados foram o de ponderação igual (Equal Weights), ordenação recíproca (Rank Reciprocal), somatória (Rank Sum), ordenação exponente (Rank Exponent) e o método do centroide (Rank Order Centroid). Para se verificar o efeito da escolha dos pesos estimados numa avaliação multicritério, avaliaram-se dados reais, aplicando-se a Ponderação Aditiva Simples (Simple Additive Weighting). Os resultados indicaram que diferentes atribuições de pesos podem alterar a posição das alternativas. Foi sugerido que a elaboração tabela ou gráficos com as distribuições de pesos pode ser útil para que o tomador decisão identifique a que melhor reflete as suas preferências.

Oct 30, 2017

By S. Gajardo, E. Valdés Guerra

Together with Sociedad Punta del Cobre S.A. (Pucobre) and Orica, we are carrying out a study of alternatives for methodology of excavation in Slot Up Raises from actually built with Blind Hole (BH) to drilling and blasting (DB) methodology. The study is part of the permanent search for innovation, the use of technology and the reduction of mine operation costs. This application aims to optimize the Sub Level Stoping method, which has historically been exploited at Pucobre. Using a new variant of the method “Open Stoping”, through the initial development of ascending blind raises using a pilot drilling of a bore hole, with the objective of eliminating the upper level in order to excavate the free face opening. This industrial test aims to replace the mechanized BH Up Raise of 1.5m (4.9 ft.) in diameter and 30m (98.4 ft.) high, with a Up Slot Raise considering two separate blasting events, using different technological enablers, as detailed below: accuracy drilling with relief holes of 254mm (10 in.) diameter, high viscosity bulk emulsion, wireless initiation system and high-strength injectable bulk resin. Considering the importance of the success of this application, a DB diagram was defined to allow the opening of the up raise in two blasting events, separated by intermediate stemming deck located at the same level at a height of 15m (49.2 ft.) from the collar, using high-strength injectable resin. The first blasting event considers the first section from the collar to the first 15m (49.2 ft.), using wired electronic initiation that is detonated on the first day. A second event blasts the section from 16.5 to 30m (54.1 to 98.4 ft.), using a wireless initiation system, as, it has no physical connection, is blasted on the second day after the extraction of the material resulting from the first event. For greater precision, the design of the explosive charge configuration and initiation sequence is made, adjusted to the measurements of trajectory deviations of the actual ground drilling and is also considered for the control of the explosive charge configuration with high viscosity bulk emulsion. This application improves the profitability of the mining business by generating savings through the change of Blind Hole methodology, estimating a savings of more than 75% per Up Slot Raise

Jan 1, 2024

By Marcelo Marchesi Martinelli, Caio Henrique Vidigal

Gasômetros são equipamentos de grande valia para aumento da eficiência energética e ambiental de empresas siderúrgicas integradas, sendo estes equipamentos responsáveis pelo controle da pressão do gás resultante das transformações dos processos siderúrgicos, controle este realizado através das variações de volume abaixo dos pistões. Quando não há disponibilidade de operação dos gasômetros faz-se necessário o uso de torres de queima para controle das pressões das redes de gases. Em dezembro de dois mil e dezoito fora realizada a troca da selagem do gasômetro de gás de Coqueria da ArcelorMittal Tubarão, que utiliza a tecnologia M.A.N. (Selo a óleo). Utilizando técnicas da metodologia Lean, modificando o mindset e alterando antigos paradigmas foi possível realizar a manutenção, de forma eficaz, em 32 dias, 28 a menos que o último trabalho similar realizado e 13 dias a menos que a meta proposta para a parada, aumentando a recuperação de gás de Coqueria, maximizando ganhos de geração elétrica e minimizando a exposição a riscos ambientais associados a parada. As ideias apresentadas neste artigo são de grande valia para a evolução do pensamento crítico e sistêmico sobre a manutenção, não só em gasômetros, mas em todo o contexto de realização de atividades já consolidadas.

Aug 1, 2019

By Dennis Wilzbacher, John Wiegand

In an effort to reduce the cost of bulk explosives, Vigo Coal Company found that the addition of coal mined at their Friendsville Mine, not only reduced explosive costs, but also appeared to actually enhance blasting performance. The Friendsville Coal lies at the base of the Mattoon geologic formation within the Mcleansboro Group of the Missourian Series of the Pennsylvanian Geologic System in Southern Illinois. Vigo Coal Company commissioned VIBRONICS, INC., an independent blasting consulting company to quantify actual blasting performance. Insitu sonic velocity testing of overburden was conducted to determine the P-wave velocity of the sandstone present at Vigo’s Cypress Creek Mine, where the initial testing was conducted. Numerous VOD (velocity of detonation) recordings were obtained for varying blends of ANFO/Coal (now named Carbo*Prill). Cast blast percentages were determined for both Carbo*Prill and non coal blended bulk explosive blasts. The VOD of the coal blended product was intentionally reduced so as to more closely match the P-wave velocity of the sandstone overburden. Explosive blends containing as much as 40-50 percent coal were tested. Explosive blends containing greater than 30 percent coal, have been used in Cypress Creek Mine overburden production blasts. The coal blends appear to produce better fragmentation and yield excellent cast blast performance. Safer mining conditions were also observed. Flyrock potential was reduced. The blasts produced less back break, producing a safer highwall. Stripping dozer and shovel production rose during the testing period and equipment repair costs were lowered due to an increase in overburden fragmentation. Blasting vibrations were reduced, in part due to the lowered detonation velocity of the ANFO/Coal mixture. The Friendsville Coal Seam appears to contain inherent chemical and physical properties that enhance blasting performance. The use of Carbo*Prill has been approved by MSHA, BATF, the State of Illinois, and the State of Indiana. This paper will provide details concerning testing procedures, blast performance analysis, recommendations and conclusions for using this alternative blasting mixture.

Jan 1, 2007

By Marco A. Ramírez-Argáez

A 2D mathematical model was developed for the plasma arc welding process. Computational simulations based on mass and momentum conservation equations as well as Maxwell equations were performed by using the commercial software PHOENICS. The model predicts the electric characteristics of the arc column, flow patterns, temperature contours and electrical potential, by varying the composition of the cover gas, in this case, argon and nitrogen. It was found that an arc of nitrogen with respect to one of argon generates more intense jets, greater voltages, and lower temperatures in the arc column for welding arcs current of 150 A and 10 mm arc length.

Oct 30, 2017

By Marcella Gautê Cavalcante Xavier

A presente proposta tem por objetivo desenvolver uma análise experimental da liga hipereutética Sn-0,5%Ni solidificada unidirecionalmente em regime transitório de fluxo de calor contra chapa molde de cobre. A liga foi avaliada quanto a sua microestrutura bruta de fusão e suas respectivas correlações com os parâmetros térmicos (velocidade da frente eutética -VE e taxa de resfriamento eutética -?E) e propriedades mecânicas. Os resultados mostram que a morfologia microestrutural predominante é composta por células ricas em estanho (β-Sn) circundadas por mistura eutética Sn+intermetálico tipo NiSn. Uma transição microestrutural foi observada entre as posições 15mm (?E=1,7°C/s) e 30mm (?E=1,1°C/s), de célula regular (CR)?célula tipo placa (CTP). Notou-se ainda a presença de intermetálicos primários NiSn distribuídos ao longo da matriz nas posições iniciais do lingote. Valores superiores de limite de resistência à tração (σu=26 MPa) e limite de escoamento (σy=21 MPa) foram encontrados para a posição 6mm a partir da base refrigerada do lingote, podendo estar relacionados com a estrutura celular mais refinada e também com a presença dos intermetálicos primários NiSn. O alongamento específico (?) comportou-se de maneira inversa, visto que as estruturas mais grosseiras (CTP) e a ausência de intermetálicos primários são responsáveis por facilitar a deformação plástica na estrutura da liga Sn-0,5%Ni, aumentando seu nível de ductilidade.

Oct 30, 2017

By Getúlio da Silva Abreu

O objetivo geral deste trabalho foi produzir e caracterizar as propriedades mecânicas de um compósito abrasivo nanoestruturado no sistema D-Si, via sinterização cíclica de alta pressão e alta temperatura (APAT). A sinterização cíclica em alta pressão e alta temperatura de compósitos foi feita a partir de uma mistura de 70% diamante e 30% de Si como ligante, e com 1 a 4 ciclos de pressão (P) de 7GPa-4GPa e temperatura (T) 1600°C-300°C, para um tempo (t) de 1min. O aumento do número de ciclos gerou razoável elevação na microdureza e densidade das amostras. Os valores médios de tenacidade à fratura ficaram entre 8,86 e 9,43 MPa.m1/2. No ensaio de desgaste o aumento do número de ciclos diminuiu a perda de massa das amostras no disco de granito. As curvas termogravimétricas apresentaram uma boa estabilidade térmica dos compósitos até a temperatura de 660ºC. Finalmente, por meio deste trabalho será possível melhorar a produção de futuros compósitos abrasivos no sistema D-Si.

Aug 16, 2017

By Hamid Mazouz, Mohammed Hakkar, Rim Jouraiphy, Fatima Ezzahra Arhouni, Ahmed Mahrou, Aziz Boukhair, Mohammed Fahad

The wet process is the most commonly used worldwide for phosphoric acid (PA) production, in which phosphate rock (PR) is reacted with strong acid mainly sulfuric acid. This work aims on studying the rare earth elements (REEs) distribution during the production of phosphoric acid using different qualities of phosphate through various industrial technologies. At the onset of this work, the process started with 12 samples of PR, PA, and phosphogypsum (PG) being taken simultaneously from two different Moroccan basins (Ouled Abdoun mine represented by K09 and Gantour mine depicted by G10, G20, BG) and various production lines at two processing platforms (Jorf Lasfar and Safi). Afterward, collected samples were prepared and analyzed for REE characterization using an inductively coupled plasma mass spectrometry (ICP-MS). Based on the analysis results, a transfer factor ( TFX) was introduced with the aim of gauging the REE distribution between PA and PG. The results showed that the total concentration of REEs in different phosphate qualities ranged from 411 to 631 ppm; the major part of this concentration was attributed to the four elements: Y, La, Ce, and Nd which constitute more than 77%. The REE distribution between PA and PG depends on neither the phosphate quality nor the industrial technology used since that the distribution results showed that 55 up to 66% of the initial REEs in phosphate rock ended up in the PG. The behavior of each REE was common except for the element scandium, which transferred mainly to the phosphoric acid.

Nov 3, 2021

By T. Uysal

Various morphological parameters that affect the flotation recovery of sphalerite were modelled and optimized using the response surface method (RSM). The effects of roughness value, shape factor, and collector concentration were investigated using the central composite full design method. The results were evaluated by analysis of variance. The optimum roughening time was found to be 25minutes, the optimum roughness value was 2.9071 μm, and the optimum collector concentrationwas 0.001 M. Using these values, a flotation recovery of 98.01% was obtained. Similarly, in shapefactor studies, the optimum grinding time was 15 seconds, the optimum roundness value 0.7421, and the optimum collector concentration 0.0009 M, which resulted in a flotation recovery of 94.30%. The average error between the optimization results and the experimental results was estimated to be less than 6%, and the R2 values were greater than 90%. The study shows that RSM can be effectively applied in finding the economic optimum condition for obtaining maximum flotation recovery with minimum reagent consumption.

Sep 6, 2023

By Luciano Aparecido Kempski

O ferramental utilizado em processos de conformação é de grande interesse da Engenharia de Superfícies devido às características tribológicas específicas encontradas nestes processos. Portanto busca-se sempre melhorar o ferramental para se obter menores coeficientes de atrito, desgaste e adesão de material sobre a superfície da ferramenta, sendo empregadas diversas técnicas de tratamentos superficiais como a nitretação e os revestimentos depositados via PVD. Uma variável importante do par tribológico é o coeficiente de atrito desenvolvido entre as superfícies em contato nos processos de conformação a frio, portanto foram realizados ensaios de pino-sobre-disco e ensaios DST, para determinação de coeficientes de atrito em pares tribológicos. Desta forma, chapas de aço inoxidável austenítico AISI 304 foram conformadas sobre uma superfície de um aço ferramenta DIN X100CrMoV8-1-1, com o propósito de se conhecer o atrito desenvolvido entre os materiais. As amostras foram nitretadas a plasma e ou revestida com TiCN, posteriormente, a caracterização da microestrutura e as propriedades avaliadas através de ensaios mecânicos e tribológicos. O ensaios proporcionaram obter valores de coeficiente de atrito para as condições de tratamentos e lubrificação utilizados e as análises dos resultados mostram um aumento da dureza superficial das amostras tanto nitretadas quanto revestidas com TiCN e uma redução do coeficiente de atrito significativa quando se faz uso do revestimento.

Aug 8, 2018

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Furnace refractories are in most cases chemically incompatible with smelter slag, which leads to a steady erosion in their thickness over time. Once too thin, refractory walls become mechanically unstable and catastrophic failure can result. Historically, external shell cooling was applied to generate a freeze lining of slag and thus prevent refractory erosion. Many modern high intensity smelting furnaces instead maintain their physical integrity by the use of internally cooled wall panels, plates or finger coolers. An initial refractory lining is often installed inside of the coolers, such that the furnace originally operates with a temperature (insulated) rather than a heat flux (freeze lined) boundary condition. This paper examines the change in slag-wall heat transfer coefficient and slag superheat as a function of process intensity. The implications of the changes in heat transfer on residual brick thickness are explored using analytical modelling.

Jan 1, 2016

By T. Bui, T. Wallmach, S. B. Blancher, A. Back, M. Pierre, V. Delarue, A. Kanzari

This study investigates nickel laterite porosity and its impact on geometallurgical modelling. We performed a detailed mineralogical study on a set of Ni-laterite samples originating from New Caledonia. Samples were analysed after heavy liquid separation by automated SEM (QEMSCAN®). Laboratory and QEMSCAN® modelling results do not correlate well. Ideal physical mineral properties such as mineral densities used in QEMSCAN® modelling do not match the actual physical densities of minerals. The presence of empty or water-filled pores can represent important amounts in minerals and change the overall density of a particle. An adequate modelling of real density separation of minerals and particles should consider the water-filled pores. The first step towards a better simulation was to integrate pores larger than 10 μm in diameter filled with water (density of 1 g/cm3) in the QEMSCAN® database. The results approached, but did not match the physical laboratory results. The second step was to identify nanometer to micrometer sized pores, which could not be identified by QEMSCAN®. It was possible to identify nanometric pores in enstatite, Fe-oxides, serpentine, talc and quartz, and radial aggregates of fibrous Fe-oxyhydroxides with high resolution SEM (HR-SEM). The quantification of those micro-sized pores was performed on 2D HR-SEM images using image-processing techniques developed in Python to calculate the nanometer to micrometer scale pores in each mineral. Despite the limitation of converting 2D imaging into 3D objects, in our case pore sizes and porosities, we were able to calculate a mean value of porosity for each mineral. The integration of this porosity in the calculation of particle densities yielded a good match between the QEMSCAN® model and the laboratory experiment results. Despite the complexity of a strongly weathered material, such as Ni-laterites, a good knowledge of the ore makes it possible to build reliable processing models. Keywords: Mineralogy, geometallurgy, nickel laterites, SEM, QEMSCAN®, porosity, density

Jan 1, 2020