Search Documents

By David E. Siskind

The Bureau of Mines studied environmental blast effects in six occupied residential structures. Airblast, ground, and structure vibrations were measured both inside and outside residences for seven quarry production blasts. Walls and floors responded to the blast noise and vibration by shaking at their own natural frequencies, often with greater peak particle velocities than the ground outside the structures or their foundations. The vibrations of the houses generated noticeable internal noise, correlating with the arrival of the groundborne energy. The later arriving airblast wave was predominantly at low infrasonic frequencies (1.0 to 1.5 Hz) and had similar amplitude and frequency characteristics both inside and out-side the structures. Significant structural motions resulted from the air-blast overpressures for at least two of the seven blasts. The most severe airblast effect occurred at a house 1,800 feet from a 5,047-pound (200-lb/ delay) blast. This stucture was subjected to a peak 0.16-in/sec particle velocity and 130 dB(L) airblast. The wall of the second floor responded to the ground vibration and airblast by shaking at particle velocities of 0.15 and 0.28 in/sec, respectively. Analysis of these data and those from additional field studies will be used to identify appropriate, safe, and reasonable impulsive noise levels, measurement techniques, and factors of design applicable to minimizing the adverse environmental effects of blasting.

Jan 1, 1976

By Andrew B. Cecala, Edward D. Thimons

The Bureau of Mines has successfully tested a method to simulate methane (CH~) flows from face areas through the returns of noncoal mines. This technique' involves releasing a small quantity of tracer gas at a working area and sampling for that gas downstream in the re- turn airways. By measuring the dilution of the tracer gas, the dilution of any volume of CH4 released at the face can be calculated. This information is useful in selecting locations for CH4 monitors and in deciding the necessity for permissible equipment in the returns.

Jan 1, 1984

By Jr. Reed

The only known large deposits of talc in Alabama occur near Winterboro, Talladega County. Preliminary examinations were made, and work by the Bureau of Mines was recommended. The deposits were investigated to determine the amount and grade of talc present and to search for new talc deposits in the general area. Seventy-five holes, totaling 3370.4 feet, were drilled with Government-owned core drills from August 1, 1948, to February 11, 1949, and 27 samples were taken for assay. This report presents the factual data disclosed by drilling and the results of beneficiation of the talc.

Jan 1, 1950

By Ellis S. Hertzog

The material published in this report is part of a special study of some of the chemical and physical properties of Alabama coals. The complete study included friability and grindability determinations, high and low temperature assay distillation tests, and ash fusion-temperature determinations. Proximate and ultimate analyses and. calorific values of the coal samples also were obtained. This paper is concerned only with grindabilities, although proximate analyses have been included to give a better picture of the problem as a whole. The growing interest in grindabilities of coals is a result of the increase in use of pulverized fuel in REscent years. The tenative ball-mill grindability method D409-35T4/was used in making all the determinations. The method of sampling and the technic of the testing procedure is described in Considerable detail in this report because the procedure was established quite recently. The ball-Mill grindability index is a measure of the ease with which coal may be ground, which may be an important factor in estimating pulverizing costs. Up to the present time few data on the grindability of Alabama coals have been published. The data in this paper show that the Warrior and Cahaba fields exhibit a wide range of grindability in their coals. The mines tested are well distributed throughout the productive areas of these fields, and it is possible to make rough estimates of the grindabilities of coals not listed in this report from the data given for mines situated in the same vicinity. ACKNOWLEDGMENTS This study was conducted at the Southern Experiment Station of the Bureau of Mines in cooperation with the University of Alabama. The Alabama liming Institute was of great assistance in furthering the investigation, and the work was undertaken largely as a result of its request that the Bureau of Mines should make certain studies of Alabama coals. Grateful acknowledgments

Jan 1, 1938

By M. Kinnunen

Handling of municipal solid waste (MSW) and control of its potential resources is becoming increasingly important in modern society. The OECD (Organization for Economic Co-operation and Development) average on municipal waste produced in 2003 was that of around 570 kg per inhabitant. In European Union countries around half amount is of MSW landfilled. In Finland still 88% of MSW was landfilled in 2004. Since incineration reduces MSW volume significantly while producing heat energy, it has become one of the most common waste handling techniques. The shortcoming of incineration is however, that incinerated MSW is often not pre-sorted and it produces slags and ashes as side streams from which recovery of metals is difficult. This paper looks into possibilities of scrap metal recovery for recycling from municipal solid waste incineration (MSWI) bottom ash. In order to do that, a flow sheet of physical separation methods was developed and tested with Finnish rotary furnace MSWI bottom ash. In addition, an empirical model for estimation of the recoveries of scrap metals with physical separation methods for treatment of MSWI bottom ash was developed. According to the results of this study, for 1 Mt of incinerated MSW with 30% mass reduction, a minimum resource potential of 100 kt for magnetic metal scrap of roughly 24 % grade and about 19 kt of non-magnetic metal scrap of roughly 65 % grade. In other words, 57 kg magnetic scrap and 12 kg non-magnetic scrap per inhabitant at the mentioned grades, respectively. Although wide variations of parameters affect the MSWI bottom ash quality, it can be said that a considerable amount of metals is drained into MSWI bottom ash. Results of this study show that from MSWI bottom ash significant material streams metal scrap can be reintroduced into the resource cycle which would otherwise be lost.

Jan 1, 2014

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the eighth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Jefferson County, Pa., which comprises parts of Marienville, Hallton, Ridgway, Brookville, DuBois, Penfield, Smicksburg, and Punxsutawney quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals is included. Data on the coal beds in the county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick, These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By P. V. Golde, R. A. Poole, G. R. Baiden

"The results being presented in this paper are those obtained during 1996 on a drilling automation project at Stobie mine. This project has successfully demonstrated that the remote operation of multiple drills (by a single driller) from surface using Tamrock Data Solo 1000 Sixty drillrigs is technically feasible and can potentially bring significant rewards in terms of productivity and work environment improvements, as well as labour and maintenance savings. BackgroundThe ObjectiveThis paper is an update of a previous report on remote drilling research at Stobie mine. Enabled by the communications system installed at the mine, the ability to remotely control underground equipment from surface has been demonstrated (Poole et al., 1996). This paper discusses the needs and process required to carry this concept to consolidate the operation of multiple machines under a single operator.The TeamThe team assembled to develop and implement the automation and the communi-cations extensions needed to allow the multiple machines’ operation from the surface by one operator included the following:INCO Mines Research supplied the project management and original project initiative. The primary purpose was to prove the advantages of savings associated with the driller not being required to travel to the underground drill location coupled with the savings associated with one-man, multiple-machine techniques.Tamrock EJC supplied the Data Solo 1000 Sixty drills and the Tamrock specific machine-based custom software. The drills were produced in Finland with no provision for remote operation of the drill from other than the umbilical attached local console.Automated Mining Systems supplied the modifications to the drill communications equipment to allow the machine communications to become broadband compatible. As well, Automated Mining Systems also supplied the hardware necessary to be able to remotely control the portable video camera, as well as the data logging equipment.Stobie Mine personnel were made available to test the function and then integrate the concept of remote control drilling into the Stobie operations."

Jan 1, 1997

By John E. Crawford

A year ago, if I had the pleasure of addressing you, I would have discussed ocean mineral resources from a promotional standpoint. I would have described exciting indications of mammoth tonnages of sea-floor industrial minerals. I would have attempted to fire your imaginations as to the potential of a nation having the technologic know-how to exploit its submerged boundaries. As a first step toward this capability, I would have solicited your support for a Bureau of Mines? program aimed at determining the industrial worth of marine minerals and devising techniques and hard- ware for their recovery. We still need your support, but recently we have ventured out of the realm of planning and into your Government's first program in marine mineral engineering. Today, I wish to describe what we have done within the framework of existing research problems and our possible goals. I will be brief so as to allow ample time for questions, and I can do this with confidence because our program is so new that I need not be chagrined at not having all the answers.

Jan 1, 1965

By Finney, W. R.

MUCH has been said and written of the "Big Inch," of the terrific obstacles encountered in its construction, of the colorful and tough men engaged in its building, but little has been publicized of the engineering and economic problems behind the scenes. Long before Pearl Harbor it was apparent to the petroleum industry that a critical oil shortage could be expected along the Atlantic seaboard, owing to delay in tanker deliveries as a result of convoy movements, and to allocation of vessels for foreign shipments. This area, with a normal consumption of approximately 1,800,000 barrels per day of oil and products, was almost entirely supplied by tanker. Pipe lines supplied an average of only 20,000 barrels per day in 1939, 40,300 barrels per day in 1940, and 55,000 barrels per day in 1941. A small amount of oil and products was also delivered via barge.

Jan 1, 1943

By J. M. Rios

This paper exposes the reasons that led the Empresa Nacional Minera del Sahara, S.A. (ENMINSA) to the selection of a conveyor belt system for the transport of phosphate rock over a distance of 100 kilometers. ENMINSA was created in 1962, with the main objetive of the exploitation of phosphate rock deposits in the Spanish province of Sahara, in North West Africa. Poor grade outcrops were known previously. A detailed geological research carried over the province led ENMINSA to the discovery of deposits not exposed, and of much higher grade. The sector known as Bu-Craa was chosen as the most promising, and was explored by means of drill holing and shafting. The important amount of information obtained permitted a detailed evaluation of the capacity and grade of the rich ore contained in the Bu-Craa area. Simultaneously with the systematic reconnaissance of the Bu-Craa deposits, ENMINSA developped the study of the technical and economical problems required for the beneficiation of the rock, which comprised five main groups of projects: rock exploitation; beneficiation plant; rock transport from the mine site to the Atlantic coast; storage, handling and loading facilities by the sea- side, and power plant. Once determined the location of the marine loading facilities, which to date are in an advanced stage of construction (figs. 1 and 2), the studies conductive to the selection of the best transport system from the mine to the ocean, along 100 kms. distance were undertaken.

Jan 1, 1968

By M Zlatev, S Silge

Producers of primary resources such as iron ore face the challenge of processing crude materials with increasing levels of impurities, which may result in the requirement for wet processing. This results in a significant increase in water usage, power consumption and operating costs. Given the remote locations of most operations in Australia (Stewart et al, 2013; Prosser, Wolf and Littleboy, 2011), the required volumes of power and fresh water for wet processing can be very difficult to achieve.HAVER&TYLER is renowned across the world for their screening technology in wet and dry processes. Its innovative Hydro-Clean® system represents a cost-effective and eco-sensitive way to clean any crude materials and material blends with a grain size distribution of 0–150 mm that are contaminated with adhesive clay, slit and other impurities.CITATION:Silge, S and Zlatev, M, 2015. Iron ore washing – achieve more with fewer resources, in Proceedings Iron Ore 2015, pp 519–528 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By N Johansson, D Johansson, A Beyglou, H Schunnesson

As demand for optimisation of mining processes increases, more attention is drawn to blast performance and fragmentation improvement. Fractures and discontinuities are among the most influential factors in blast results, therefore one of the initial steps towards blast optimisation is to gather information about the rock mass and integrate it in blast design. This paper presents a method for assessment of rock mass discontinuities and integrating it in production blasts in the Aitik open pit copper mine in Sweden.3D photogrammetric techniques were utilised to map discontinuities and distinguish domains of similar geologic structures in the pit. As a pilot study for a future campaign, four different initiation directions were tested through six pilot blasts in one of the domains. The results were compared in terms of swell and loading efficiency of rope shovels to identify the correlation between blast performance and initiation direction compared to major discontinuity families.It was established that in the trial domain, blasts initiated towards north or north-west yielded larger swell and better performance of loading. Comparing these blasts with discontinuity families show that there is a correlation between blast performance and initiation direction according to the dip and strike of these discontinuities. Such knowledge can be used for future blasts in the same domain to increase long-term operational efficiency through slight modifications in drill pattern and initiation design.CITATION:Beyglou, A, Schunnesson, H, Johansson, D and Johansson, N, 2015. Adjusting initiation direction to domains of rock mass discontinuities in Aitik open pit mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Staff, G. M. Hogg

"The eastern portion of the Late Precambrian geosynclinal structure known as the Labrador Trough comprises a 16,000-square-mile sulphide-bearing belt of good potential as a base metal exploration area. Hollinger and Hanna mining interests have carried on exploration in the region since 1953, with encouraging results. This program has been considerable in terms of both effort and expenditure, and has resulted in an apparently successful primary evaluation of the entire belt.Much detailed work remains to be done in the area. Exploration to date has been largely of a reconnaissance nature, employing various methods in common use in Canada today. In the course of this work, several deposits of promise, containing near-economic quantities of copper, zinc, nickel and other metals, have been located. A broad classification of these deposits is proposed.Exploration in the sulphide belt was started on the basis of partial control of the area under mineral exploration concessions. This was necessary to justify operations in an area of difficult access and high operating costs. The results of this now-terminated arrangement are regarded as being of benefit to those directly concerned as well as to the mineral industry in general."

Jan 1, 1966

By W. R. Ernst

A method for the removal of nickel and vanadium contaminants from spent HDS catalysts involves pretreating the catalyst with H2S followed by the extraction of the metals with an acidic solution of ferric ion. The ferric ion solution alone removes significant amounts of active ingredients cobalt and molybdenum; however, after pretreating the catalyst with H2S, the extraction becomes more selective for the removal of Ni and V.

Jan 1, 1986

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize biomass productivity, the influence of reclamation practices on biomass production must be well understood, which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass estimations and, also, the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, experimental biomass production plots on reclaimed mine sites established in Wise County, VA, are used for a comparative study of satellite spectral derivatives, which are evaluated against groundbased biomass estimates. Metrics based on four spectral derivatives, band ratios and spectral transforms were regressed against biomass measured in situ for different species. The results demonstrate that greenness and principal component 2 (PC2) were more efficient than the other spectral derivatives for monitoring the biomass of this reclaimed area. Also, it is shown that Landsat-5 TM has provided promising results for monitoring of the biomass changes occurring from 2008 to 2010 over the study area.

By M. Akser

Ilmenite, rutile, and zircon deposits of commercial importance have not been reported to-date from Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit along the Black Sea coast of Turkey in the vicinity of Ormanli, northwest of Istanbul. Consequently beach and sand dune samples were collected from that area for additional analysis. Laboratory methodologies, designed to simulate standard industrial heavy-mineral plant practices, were used to analyze and evaluate the samples. Based on the analyses, and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1995

By G. Viramontes-Gamboa, A. Encinas-Oropesa, S. Velázquez-Roque, L. A. Ibarra-Bracamontes

Some industrially relevant applications for pyrite nano/micro-particles have been proposed in the literature, such as the catalysis of chalcopyrite leaching, the removal of As(III), As(V) and Cr(VI) from solution, as photovoltaic devices, and others. Even though pyrite can be recovered from solution by flotation, for some applications it may be beneficial to provide pyrite with magnetic properties. In this work, a methodology to synthesize magnetic shell/core composites made of pyrite as the shell and either natural or synthetic magnetite as the core is presented. The size of the magnetic composite may range from tenths to hundreds of microns. The synthesis is basically made by stoichiometrically mixing iron nano/micro-particles with sulfur microparticles with magnetite particles, and bringing the mixture in an oxygen free atmosphere from 200 to 300 °C for 4 h. The composites were characterized by optical microscopy, Scanning Electron Microscopy and X-Ray diffraction.

Jan 1, 2014

By Nathaniel Arbiter

The question of automation of concentrator operations with computer control is under increasing consideration. Some of the problems involved will be discussed from the viewpoint of the availability of the requisite, detailed knowledge of the unit operations. The justification for full-scale automation of a mill must ultimately be economic--an increase in profitability over and above the cost of instrumentation and development, Potential savings would be in three probable directions: decrease in operating labor costs by substitution of machine control; improved metallurgy through continuous effective control; and decreased operating costs by achieving higher unit capacities and process efficiencies.

Jan 1, 1962

By W. R. Smith

Introduction No commercial deposits of silica sand are known to occur in British Columbia, so all requirements for foundry and other uses must be imported. During the war, nearly 5,000 tons per year were used, all originating in Illinois and delivered to local consumers for about $12.00 per ton. Present requirements are somewhat less, but the cost is still of the same order. The relatively high cost of silica sand in British Columbia is not only a serious item for present consumers, but might be a deterrent to the establishment of a glass industry, should this be contemplated at any time. The present investigation was undertaken in an attempt to provide a cheaper source of silica sand within the Province. In 1936, a large number of beach and bank sand deposits in the lower coastal region of British Columbia were examined by the British Columbia Department of Mines, and samples were analyzed chemically and mineralogically. The deposits over the whole area proved remarkably uniform in mineral composition, consisting essentially of quartz, feldspar, ferromagnesian minerals, rock fragments, and various accessory minerals, and differing only in the relative proportions of the various constituents. In no case did the quartz content of any sand exceed about 40 percent and the average was of the order of 20 to 30 percent.

Jan 1, 1947

By E. P. Lunghofer

Silicon Carbide and Aluminum Oxide were two of the early forms of man-made abrasives often referred to as synthetic and were invented at the turn of the century. Edward G. Acheson invented Silicon Carbide in 1893 and Charles F. Jacobs filed a patent for the manufacture of fused alumina from bauxite in 1900. Jacobs' patent provided a method for tempering the alumina by reduction and fusion to a degree of hardness and toughness suitable for abrasive purposes. These two inventions are the basis of the synthetic abrasive industry today. Improvements have been made in the equipment used in the process, however the process itself remains basically the same. In 1904 A. C. Higgins observed that hot spots developed on the shell of the pot furnace used in the reduction of bauxite. He found that by spraying water on the hot spots they could be prevented and, in addition, they failed to return in the same place. Higgins reasoned that the cooling effect of the water caused the melt contacting the metal shell to freeze as an insulating autogenous refractory. This suggested that an improved furnace design could be obtained by using a metal shell which is continuously flooded with water on the exterior surface. Paradoxically, a furnace required to contain tons of molten Aluminun Oxide was thus constructed of nothing but a sheet steel shell with no refractory lining at all. A test of such an arrangement was tried by Higgins with considerable trepidation and was found to be extremely satisfactory.

Jan 1, 1985