Search Documents

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By J. Paraszczak

High productivity of the equipment employed is one of the key factors in reducing production cost in mining. One of the best ways to achieve it is an increase in availability. In order to identify the most adverse factors affecting it, reliability and maintainability analysis ought to be done. If its results are to be conclusive, a sufficient amount of credible and consistent data is indispensable. Following the experience from field studies done in underground mines, this paper discusses the current status of failure and maintenance reporting, as well as problems encountered. It exposes the importance of adequate data collection on failures and downtime as well as it reviews the benefits of analysis based on such material. The question of benchmarking with regards to mining equipment performance is also addressed. The paper concludes with some recommendations on data collection and processing, as well as stresses the need to standardize the most important reliability/ maintenance notions throughout the mining industry and to conceive appropriate performance measures.

Jan 1, 2000

By N. Dhawan

In the last decades, High Pressure Grinding Roll (HPGR) has gained significant importance in hard rock processing due to numerous metallurgical benefits such as energy savings, particle weakening, preferential damage of coarse particles, and preferential comminution-liberation. There are a limited numbers of lab-scale HPGR units throughout the world. The laboratory-scale HPGR machine at the University of Utah is first-ever lab-scale machine designed by late Dr Klaus Schönert, the inventor of HPGR. This HPGR is constructed with two counter-rotating hardened tool steel rolls, each 200 mm in diameter and 100 mm in width. The HPGR unit is equipped with eight sensors and a robust control system, which serves as an ideal system for fundamental studies and lab-scale testing. In HPGR operation, throughput, energy and product size distribution are intricately linked to specific grinding pressure, roll gap and rolls speed. The nip angle existing during the operation determines the volume of feed material above the rolls that is pulled into rolls without slip. In this paper, scale-up factors and some of the existing models have been reviewed. A number of experiments have been carried out with limestone and a slag material. The influence of operating variables and their complex relationship has been studied.

Sep 1, 2012

By A. Nieto

Rare earth elements (REEs) are crucial to green technology such as hybrid-electric vehicles, wind turbines and fluorescent light bulbs. As of 2011, China dominates the global production of REEs and is reducing its export quotas. To predict the supply of rare earths in the United States based on future supply scenarios, a web-based database and geographic visualization tool was built. Five case scenarios with varying levels of REE demand were created by varying several economic conditions including (1) international trade policy, (2) greenhouse gas regulations, (3) environmental mining regulations and (4) tech applicability ratio of REEs. The most likely scenario, which is based on current international demand levels, indicates the importance of expediting the development of extractive operations of current REE resources within the United States. The results of the different case scenarios are supported by using dynamic geographic maps indicating the location of rare earth ore (REO) resources.

Jan 1, 2012

By A. Treverrow, G. A. Brooks, H. K. Worner

"The work by H.K Worner and co-workers at CRA in the 1960s, and early 1970s, established that molten metals could be refined continuously utilising counter current flow of metal and slag. Womer also demonstrated that counter current refining could produce highly refined metal products. These developments coincided with the advent of high intensity metallurgical reactors in both the ferrous and non-ferrous industries (e.g. BOS, Q-BOP and later Sirosmelt) that utilised high levels of gas injection to produce rapid stirring and very fast reaction. These new generation of high intensity metallurgical reactors allowed high tonnage rates through relatively small volume vessels.Whilst, it is well known that the counter current flow of reacting phases offers the potential of efficient mass transfer and high purity products, the application of counter current reactors to molten metal/slag systems has been criticized on the basis that they suffer from either low intensity or, alternately, from poor refining due to excessive dispersion. These criticisms relate to the balance between intensity and the refining capacity of a reactor. That is, whilst high levels of mixing transversely to the direction of flow promotes high mass transfer, longitudinal mixing (dispersion) is detrimental to refining. Of course, mixing in one direction invariably leads to mixing in other directions, thus creating a playoff between high mass transfer and excessive dispersion.This balance between intensity and refining has been the subject of recent studies overseas, and at"" the University of Wollongong, using cold modelling techniques to evaluate the effect of mixing on dispersion in a counter current refining launder. These studies have shown that for a given geometry and mixing regime, dispersion decreases with increasing flow of liquid phases. This means that whilst high mass transfer cannot be achieved in a refining launder without sacrificing the degree of refinement, there is no impediment to achieving high productivity through such a system, in fact, high through puts may favour good refining. Thus, it may be possible to match a high productivity smelting operation with a equally productive counter current refining stage."

Jan 1, 1996

By M Yahyaei, M S. Powell

Mineral processing plants have become large and complex, generally through progressive expansions. Addition of a pre-crushing stage to conventional Semi-Autogenous-Grinding (SAG) and ball mill - crushing (SABC) circuits has introduced a complex materials handling system coping with +200 mm particles. Application of High Pressure Grinding Rolls (HPGRs) and implementing hybrid comminution circuits (ie, HPGR-SAG mill) requires proactive control of the feed size distribution to each unit. Application of Vertical Tower Mills (VTMs) and other fine grinding equipment to achieve a finer grind size, while maintaining the throughput, requires splitting the feed evenly between parallel units. Many of the conventional comminution circuits (ie, staged crushing and screening followed by staged ball milling) must deal with the transition from open pit ore, which is generally altered and soft, to underground ore, which is intact and hard, requiring existing crushers to produce a finer product to unload the ball mills.This paper presents common process improvement opportunities which have been identified during a number plant process reviews conducted by the authors in Australian and international operations. The operation of comminution circuits to known and accepted standards, which is explained in this paper, could improve the performance of circuits by between 5 and 10 per cent, generally at no capital cost and often at a lower operating cost. The performance improvement can be realised as throughput increase, a finer product size, or reduced operating costs (ie, energy saving, low maintenance, less consumables).Process optimisation opportunities presented in this paper include: enhancing materials handling and storage to avoid segregation; standard operation of screens to reduce misplaced materials; proper feeding arrangement and control of crushers to increase their utilisation; preparing proper feed for SAG mills to reduce grind size; splitting the feed evenly between parallel equipment to improve utilisation, and controlling operation of classification units to improve energy utilisation.CITATION:Yahyaei, M and Powell, M S, 2018. Production improvement opportunities in comminution circuits, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 233–248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By T Baumgartl, C Gonzales, A Soliman, M Edraki

A soil cover isolates potentially acid-forming (PAF) mine wastes from atmospheric interaction and thereby mitigates acid mine drainage. As a cover that comprises either a single layer or a composite barrier, it essentially manages percolating rain water from flowing into these PAF materials and minimises air flow as oxygen has low diffusivity in saturated soils. However, the availability of suitable soils as cover materials is limited, especially in arid and semi-arid regions where weathering rates are low.This paper investigates the potential use of mine wastes as cover materials in a water-shedding soil cover in north-west Queensland. Four cover trial plots were built using mine wastes as cover materials. Each 2.3 m cover trial plot consisted of a 1.5 m soil cover made up of waste rocks and fines, a 0.5 m drainage layer that consisted of 0.1 m waste rock aggregates and a base layer made up of blended mine tailings. The hydrologic properties of cover materials were determined by in situ measurements and laboratory experiments, which, in turn, were used as input in a numerical model that described the cover’s transient soil moisture profile. The successful performance of the cover is reliant on the long-term stable geochemical behaviour of the substrate used as cover material. Therefore, investigations were carried out to determine the geochemical properties of the cover materials constructed from benign waste rock using static and kinetic tests, with the objective to increase the level of certainty of the material’s benign characteristics. Consequently, the long-term performance of this water-shedding cover design is described in terms of the physico-chemical characteristics of its outflows.CITATION:Gonzales, C, Baumgartl, T, Edraki, M and Soliman, A, ?2014. Mine wastes as cover materials in a water-shedding soil cover in north-west Queensland, in Proceedings Life-of-Mine 2014 , pp 261–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By R Dimitrakopoulos, I Minniakhmetov

Geostatistical simulation techniques are used to quantify uncertainty of spatial attributes of interest describing mineral deposits, petroleum reservoirs, hydrogeological horizons, environmental contaminants and so on. The majority of existing methods consider second-order spatial statistics and Gaussian processes, while the more advanced multiple point-based simulation approaches are algorithmic and do not consistently account for the high-order spatial relations in data. Recently, simulation techniques for complex and non-Gaussian spatially distributed variables have been developed, based on high-order spatial cumulants, and make no assumptions on data distribution or require data transformations. In this paper, the previous developments are extended and a new approach for the joint simulation of multiple correlated variables using high-order spatial statistics is proposed. The technique is based on a new algorithm for the decorrelation of correlated variables into factors, using the so-termed diagonal domination condition of high-order cumulants. The decorrelated factors are then simulated using high-order simulation and back-transformed into the initial correlated variables. The decorrelation using diagonal domination of high-order statistics is tested with a data set from a multielement iron ore deposit, and then a fully known two-dimensional data set with two correlated variables is used to demonstrate the practical intricacies of the proposed method.CITATION:Minniakhmetov, I and Dimitrakopoulos, R, 2014. Joint simulation of correlated variables using high-order spatial statistics for orebody modelling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 53–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J. F. T. Agapito

Stability in Exxon's Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985

By W. J. Karwoski

A ground-support system for grizzly and haulage drifts was tested in Magma Copper Co.'s San Manuel mine. Eight two-piece, wide- flange steel sets were erected in a ventilation drift on the 2315 grizzly level. The sets were lagged with three different materials and back- packed with pea gravel and sand. The pillar on either side of the drift support system was instrumented with stressmeters and rock-bolt load cells, the backfill with pressure cells, and the steel sets with load cells. Results indicate a better survival rate than with typical monolithic concrete.

Jan 1, 1979

By D. Skelton

The Renard kimberlite cluster is located in the Monts Otish region of Quebec, Canada. A Canadian National Instrument (NI) 43-101 compliant resource statement for the Renard kimberlites 2, 3, 4 and 9 and the Lynx kimberlite dyke was first issued in 2008 followed by a Preliminary Economic Assessment and the development of a conceptual mine plan. Following a successful drill program in 2009 that greatly expanded the amount of kimberlite in Renard 2, a revised resource statement was issued in December 2009 comprising 23 million carats of Indicated Mineral Resources and 13 million carats of Inferred Mineral Resources, a threefold increase on the previous estimate. The project is currently the focus of a second Preliminary Economic Assessment and it is expected that a full feasibility and permitting program will commence in 2010 leading to the creation of Quebec's first diamond mine by 2013.

Jan 1, 2010

This report presents a Bureau of Mines study comparing the construction costs, leakage measurements, and predicted performance of different types of large stoppings built and tested in a room-and-pillar oil-shale mine. The six full-sized structures (30 ft high by 55 ft wide) included both permanent and temporary stoppings and were fabricated using materials ranging from structural steel to coated brattice cloth. Leakage across each stopping was measured at differential pressures ranging up to 1.0 in w.g., using both the brattice window method and sulfur hexa-fluoride (SF6) tracer gas. Blast air pressures resulting from a full-scale face blast of approximately 1,800 lb of ammonium nitrate-fuel oil (ANFO) explosives were measured across two of the stoppings and the pre-and post-leakage rates were compared for all the stoppings. Overall performance of the stoppings for production applications was evaluated using an operational model of a two-panel oil-shale mine. Different combinations of temporary and permanent stoppings were evaluated based upon ventilation performance and construction and operating costs.

Jan 1, 1988

By Lebeau M., P. Duguay

"The cost of occupational injuries and diseases in the mining industry in Quebec was estimated for the period of 2010 to 2012. The method used takes into account the financial and human costs assumed by employers, workers, and the community. To better direct research and prevention toward issues with the most significant consequences, the results are presented in various ranking tables, which stakeholders might find useful.RÉSUMÉ Le coût des accidents du travail et des maladies professionnelles dans l’industrie minière au Québec a été estimé pour la période 2010-2012. La méthode utilisée prend en compte les coûts financiers et humains endossés par les employeurs, les travailleurs et la communauté. Afin de mieux orienter les recherches et la prévention vers les problèmes ayant les plus graves conséquences, les résultats sont présentés dans divers tableaux de classement, qui seront d’une grande utilité aux parties prenantes. INTRODUCTIONThe mining industry is much safer today than it was 30 or 40 years ago, mainly due to a more qualified workforce, the use of automated equipment, and a corporate culture more focused on occupational health and safety (OHS); however, the number and the severity of occupational injuries and diseases continue to make this industry one of the most hazardous. In the province of Quebec, the mining industry accounts for approximately 0.4% of paid workers but is the source of 4% of fatal work accidents. It is, therefore, important to continue the prevention efforts already underway in the mining industry.The difficult global economy, which has affected the mining industry in the last few years, is an opportunity to reaffirm that sound management of OHS can have a positive impact on companies’ productivity and profitability. Occupational injuries and diseases are costly for the companies concerned and for society as a whole. Reducing their occurrence makes it possible to reduce not only the size of workers’ compensation board contributions but also several other financial and human costs."

Jan 1, 2018

By Albert F. Baker

Techniques were developed and circuitry was assembled for measuring the total and volume resistances to the flow of electric current through solid specimens of anthracite. The two-, three-, and four-terminal test methods demonstrated the extreme sensitivity of resistivity to differences in anthracite characteristics and showed response to changes resulting from variations in structure, temperature, and moisture content.

Jan 1, 1966

By Jack D. Ramsdell

Electrorefined, magnesium-reduced, and sodium-reduced titanium samples were evaluated for recrystallization behavior, effect of cold rolling on tensile properties, and bend ductility. Curves were determined for the softening of 2.5 to 80 percent reduced cold-rolled metal that was annealed over a temperature range of 300° to 800° C. Upon annealing, coarsening of the grains was found to occur for reductions in thickness of less than 20 percent in titanium made by all three processes. The presence of metallic impurities greatly inhibits coarsening for reductions in thickness below 20 percent, but for reductions in excess of 20 percent grain size is essentially constant at each annealing temperature. The three grades of titanium did not harden excessively from cold rolling; both tensile and bend ductility were good for reduction in thickness up to 80 percent. Upon annealing, softening occurs between 400° and 600° C., and, based on microstructure and property studies, full annealing is accomplished after 30 minutes at 700° C. for the magnesium-reduced and electrorefined titanium and at 800° C. for the sodium-reduced titanium.

Jan 1, 1960

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength. Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics. The analysis suggests grinding depends mainly on the state of aggregation of the ground products in- side the mill and the pulp fluidity. Implications of the observed effects on ultrafine grinding in general are discussed.

Jan 1, 1983

ABSTRACT This paper details the work of RISKGATE, the largest Australian Coal Association Research Program (ACARP) occupational health and safety initiative to date. The program is an interactive online risk management system developed to maximize health and safety performance in the coal mining industry by implementing continuous improvement in managing major unwanted events. The comprehensive knowledge base covers tires, collisions, fires, isolation, strata control underground, ground control open cut, explosions, explosives, manual tasks, and slips/trips/falls. All major Australian coal mining companies contributed topic experts to this broad industry initiative: nine coal mining companies, more than 80 experts, and more than 400 days of individual time for knowledge-capture workshops.

Jan 1, 2014

By M. Dadvand, G. Kipuros, A. Dadvand

"The ability to codeposit fillers within a nickel matrix has led to the production of a new generation of cermet coatings with properties useful for various applications. Hexagonal boron nitride (hBN) is a ceramic-type particulate matter with thermal conductivity, thermal stability, inertness, and lubricity properties that allow it to be codeposited. In this paper, a method was developed for modifying hBN surfaces to allow them to be uniformly dispersed in water-based solutions such as an electroless nickel plating bath. hBN surface modification improved wear performance of the electroless plated cermet due to enhanced interaction between the particulate and nickel matrix. RÉSUMÉ La capacité à effectuer un dépôt simultané de charges dans une matrice nickel a abouti à la production d’une nouvelle génération de revêtements cermet (une combinaison de céramique et de métal) dotés de propriétés très utiles pour diverses applications. Le nitrure de bore hexagonal (h-BN) est une matière particulaire de type céramique utilisée pour ses excellentes conductivité et stabilité thermiques, son inertie ainsi que son caractère lubrifiant, qui permettent son dépôt simultané. Cet article explore une méthode mise au point pour modifier les surfaces du h-BN de manière à ce qu’elles se répandent uniformément dans des solutions aqueuses telles qu’un bain de dépôt autocatalytique de nickel. La modification des surfaces du h-BN a amélioré la résistance à l’usure du placage autocatalytique du cermet en raison d’une interaction accrue entre la matière particulaire et la matrice nickel.INTRODUCTION Electroless nickel alloy coatings can be used for many applications; however, the need for improved tribological properties such as higher wear resistance and better lubricity has increased interest in incorporating particulates (fillers) into the nickel matrix by codepositing the particulates with nickel during the plating process. The selection of the particulate type depends on the desired properties (Sahoo & Das, 2011; Sudagar, Lian, & Sha, 2013). In terms of tribological applications, electroless nickel-based composites are categorized mainly into lubricating and wear-resistant composite coatings depending on the type of particles incorporated. The electroless nickel-phosphorus (Ni-P) composite coatings are composed of codeposited solid lubricants such as polytetrafluoroethylene (PTFE), graphite, WS2, MoS2, and hexagonal boron nitride (hBN) and, compared to nanocomposite electroless Ni-P coatings, they demonstrate a lower coefficient of friction. On the other hand, the nickel-phosphorus wear-resistant composite coatings are composed of hard particles such as silicon carbide (SiC), aluminum oxide (Al2O3), boron carbide (B4C), silicon nitride (Si3N4), diamond, tungsten carbide (WC), and zirconium oxide (ZrO2) and, compared to nanocomposite electroless Ni-P coatings, they have higher hardness and better wear resistance (Sahoo & Das, 2011; Sudagar et al., 2013; Parucker, Klein, Binder, Ristow, & Binder, 2014; Chakarova, Georgieva, Petrova, Dobreva, & Stoychev, 2016)."

Jan 1, 2018

By Tapan Goswami, Stephen Jeric, Geoff Brent

Highwall failures in large deep open cut mines have very significant safety and commercial implications. There are many factors influencing the stability of highwalls. The major influence is the interaction of the local geology with the shape of the pit wall. This factor is in the realm of the geotechnical engineer and is beyond the control of the blasting engineer. However, a secondary influence is the blastinduced damage to the wall. In most open cut metal mines the blasting strategy to control this damage involves the use of separate production and trim blasts bounded by presplits at the final wall.

Jan 1, 2011

By G. Alfano

We have investigated the breakage actions of solid particles observed in a new generation fluid energy micronizer being set up at our laboratories. The attention has been focussed in particular on breakage caused by interparticle collision, particle impact against a fixed surface, interparticle attrition and particle against wall of jet mill attrition. We have also studied the influence of grain size distribution, maximum particle size, flow rate and characteristics of the solid to be processed, as well as of flow rate and pressure of injected air on the above mechanism. Lastly, the operating parameters of a dynamic air classifier in closed circuit with the micronizer for recovering the fine fraction and automatically recycling the oversize, have been optimized. The findings of this investigation have been used to design, build and fine tune a micronizer capable of controlling the top size of a product having average particle size that meets market requirements for fine powders, while keeping power consumption relatively low.

Jan 1, 2014