Search Documents

By Charles Barrett

RECRYSTALLIZATION textures-the orientations of grains after recrys-tallization-have been studied extensively not only because of their metallurgical importance but also because of the information they yield regarding the atomic movements during recrystallization. Recrystallized grains must possess the same orientations as the submicroscopic nuclei from which they have grown, and thus they offer a direct road by which experimenters can penetrate the submicroscopic realm. Many perplexing results have come of these studies, but one of the most striking has been the apparent difference in behavior between single crystals and polycrystalline grains. For example, Burgers and Louwerse have shown' that when single crystals of aluminum are deformed by compression and are recrystallized (at 600° C.) the new grains appear with orientations that are different from the orientations of the deformed crystal in which they grew; but polycrystalline specimens, on the other hand, appear to have a [110] fiber texture both before and after recrystal-lization and thus to retain their texture during recrystallization. This apparent difference between the habits of single crystals and small grains is the subject of the first part of the present research and has been explained by findings reported herein. A similar situation appears to exist for aluminum when elongated or drawn into wires, for single crystals alter their orientation2,3 and polycrystalline wires retain their texture 4,1 6 upon recrystallization after elongation (at least with high-purity alumi-num), and it is possible that the explanation found in this paper for compression can be extended to cover elongation and other types of deformation as well. The second part of this paper deals with the theory of recrystallization textures. In the most successful theory for aluminum recrystallized after compression,1 much weight is given to the orientation of highly stressed nuclei in the deformed material. Taylor's "local distortions" are assumed to exist along the slip planes where displacement has occurred, consisting of fragments rotated in a specific way with reference to the slip plane and slip direction; namely, about an axis lying in the slip plane perpendicular to the slip direction. 1,7,8,9

Jan 1, 1940

By Dr. O’Neil Thomas J., Donald W. Gentry

There are mines that make us happy, There are mines that make us blue, There are mines that steal away the tear-drops As the sunbeams steal away the dew. There are mines that have lost the ore chute faulted, When the ore's forever lost to view, But the mines that fill my heart with sunshine, Are the mines that I sold to you. -Anonymous INTRODUCTION The preceding chapters have discussed, in various degrees of detail, the primary considerations necessary to perform a cash flow analysis of a mining-related investment opportunity. Although the previous discussions regarding the manipulations, calculations, and interrelationships of the various components of the pro forma income statement were illustrated in the text, many individuals are un- familiar with the format and appearance of a final spread sheet for the evaluation of a mining property. As a result, it seems appropriate to conclude this book with an abbreviated case study of an actual mine property (currently in production) showing the cash flow analysis and some back-up data. Obviously all of the supporting data and calculations for the case study presented cannot be provided; however, reference is made to the major assumptions utilized and to the appropriate procedures employed in the calculations, as described elsewhere in the text. The problem associated with using any case study for illustrative purposes is that one tends to be overwhelmed by detail. For instance, specific costs, prices, expenditure timings, and other variable values may be challenged because they either do not conform to one's expectations or are not consistent with specific operating experiences. When this occurs the instructional value of the problem becomes obscured. The purpose of most case studies, and particularly the one presented in this chapter, is to expose the student to the methodology, procedure, and format associated with performing a cash flow analysis of a mining property. It is not to laboriously wade through the specific details associated with operating and capital cost development, mine plans, or equipment schedules. It should be noted, how- ever, that the values represented in this case study result from specific mine plans, operating procedures, equipment spreads, manpower requirements, and other en-

Jan 1, 1984

By W. L. Saunders

It has been estimated that the value of the mineral products of the United States is about $2,000,000,000 a year; that about $25,000,000 is expended annually for explosives and that about double this sum is paid in wages where blasting is done. The value of the mineral products does not adequately express the importance of the industry involved in the excavation of rock and ore because of the enormous sums of money expended in tunnel driving, in quarries, and in open-cut excavation generally. We know that the Catskill Aqueduct in the neighborhood of New York, which is now nearing completion, has cost some $165,000,000 and that about one-third of this may be rated as rock excavation. These illustrations are given in order to call attention to the great importance of an industry the extension and development of which in our industrial life depend so much upon the economics of rock drilling. Reference has been made to the new Catskill Aqueduct. There are three aqueducts leading into New York, each built at periods separated by some 20 years of time. The first one, known as the Old Aqueduct, conveys the waters of the Croton river to New York City in a manner which reminds one of the old Roman aqueducts, the ruins of which are still in evidence. The engineers who laid out these old conduits sought to direct their lines around the hills and into the valleys, at all times avoiding the rock. When it was necessary to cross a river or a deep ravine, a bridge or causeway was constructed. High Bridge, over the Harlem river, is an arched masonry viaduct differing in no essential features from the aqueducts of the Romans. When the second Croton Aqueduct was built, about the year 1890, the art of drilling rock had been so far perfected, and the use of explosives, through the invention of dynamite, had become so general, that this waterway was planned and executed on straight lines, following rather than avoiding the rock. The second Croton Aqueduct is a tunnel through rock, about 32 miles in length; material gneiss, almost as hard as granite. Its construction was made practicable by sinking

Jan 1, 1914

By F. Rosenblum, P. Cancilla

The manual moisture determination methods employed today by mineral processing plants falls short in providing timely information required for automatic control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation, that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool. A novel on-line determination system for ore concentrate moisture content would replace the normally tedious classic manual procedure. Since the introduction of microelectronic¬based control systems, operators have strived to reduce the treatment costs to the minimum therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the "wish list" of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done in the classical technique of loss in weight utilizing uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7 to 9%. Many times, delays in manually achieving reliable feedback on the moisture content results in the moisture varying from 5 to 12% before corrective actions can be made. This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper describes a unique and promising on-line moisture sensor in two mineral processing applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarize the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content.

Jan 1, 2002

By R. E. McNulty, R. D. Heidenreich, C. H. Gerould

TIIE electron microscope techniques and their application to magnesium alloys that are to be discussed in this paper are the result of research at The Dow Chemical Co. over the past three years. The view- point underlying the work is not wholly metallurgical, but has evolved through a variety of problems related to the physics and chemistry of surfaces. It can be said that the interest and stimulus were closely associated with a desire to employ effectively the electron microscope in research concerning the properties of solids as related to their physical structure. Only a portion of this work will be described here, and, consequently, many points of interest and debate are of necessity either only briefly recognized or are completely omitted. As has been pointed out by Desch,1 a great deal of the knowledge of the structure of metals has been obtained through microscopic studies of the surfaces of metallic specimens prepared in a particular manner. This information, when added to that obtained by means of thermal, electrical, X-ray, dilatometric and other methods, has been of great value both from a theoretical and a practical view- point. With the introduction of new instruments such as the electron diffraction camera and the electron microscope, it would be expected that still more information could be obtained. These two instruments have in many instances been very effective when directed toward the investigation of metallic surfaces, provided the proper methods of surface preparation were employed. Experience shows that the problems of surface preparation greatly limit the general application of these instruments to metallographic studies. It was found necessary to discard the standard metallographic procedures in applying the electron microscope to magnesium alloys and to work out new methods, which were required to satisfy certain conditions. These methods are unique to magnesium only in the specific chemical reactions occurring during etching. The presentation of the methods and results will be ordered as follows: I. Electron Microscopy of Surfaces. 2. Surface Preparation of Magnesium Alloys. 3. Discussion of Microstructures. a. Pure Magnesium and Single-crystal Studies. b. Types of Precipitation. c. Some Common Structures. d. Special Micrographs and Techniques. e. Structure of Mg-A1 Solid Solutions. 4. Correlation of "Fine Structure" with Corrosion Behavior of Magnesium Alloys.

Jan 1, 1946

By David Miller

"The biggest concern about using soil mixing is the inability to observe physically the final product, which has led to a lack of confidence about what is in the ground. After all, you can’t see it and you can’t taste it and you can’t smell it, so are you sure it’s soil mixing? In addition, there are variations in techniques, tools and monitoring that have led to additional skepticism and the desire to “elevate” the product. This skepticism is why the industry is so scrutinized even when there are other technologies being used that do not experience nearly the same level of scrutiny. With other techniques, even with a slurry wall, you can see the backfill before it goes into the ground, and drilled piers have careful evaluation of the concrete mix even before placement into and verification of the open hole. Essentially, you get control over the final material. There is less control in soil mixing, and it’s very dependent on in-situ conditions. These factors make it difficult to rely solely upon installation parameters, quality control (QC) and verification tests. At some point, you may need to apply some engineering judgment.Start at the BeginningThe availability of sufficient and accurate geotechnical data (soil type, heterogeneity, shear strength parameters, variability, etc.) is important in establishing the material that will be drilled. This data will also help in determining the proper mix design to achieve the desired soil cement properties. Many factors must be considered when designing the mix and the mixing program, including any debris in the ground, different soil properties and varying moisture contents.Each of the various factors affect the final properties of the soil cement, so it really takes careful planning and evaluation of the mix design through iterations by looking at the soil types and adjusting the mixes. Clay is going to behave very differently than sand in both mixing efficiency and final properties. That is, the presence of clays results in more difficulty in achieving higher strengths and to physically mix the soil and the binder, whereas the presence of sands results in more difficulty controlling the final permeability."

Jan 1, 2017

By R. E. Stewart

"Using the concept of economic life and marginal analysis, it can be shown that proper equipment replacement timing can save a mining company many thousands of dollars. To assist management with determining the economic life of mining equipment, a new computer package has been developed. The package, called ERG (equipment replacement guide), incorporates all important economic factors related to equipment usage, such as operating costs, maintenance costs, salvage values, depreciation, volume of work, tax credits, inflation rates, ROJ, etc. The information is used in a series of equations which balance the costs of new equipment against the total cost of old equipment. The solution of the equations determines economic life and the point in time when the old equipment should be replaced. IntroductionIn an operating mine, equipment must eventually be replaced or downgraded for a variety of reasons. Fleets of haul trucks, dozers and other major pieces of equipment deteriorate over time until the mounting costs of maintenance and repair force either a major overhaul or the ir replacement by new and more efficient pieces of equipment.The question of determining the best time to replace old equipment has been approached in many different ways. Various methods, ranging from operating experience, intuition and physical necessity to sophisticated computer models have been devised to help cope with equipment replacement decisions . The best of the se will incorporate the most important economic factors related to equipment usage, such as operating and maintenance costs, salvage values, depreciation, work delivered, the cost of capital, tax credits and, of course, the effects of inflation.Economic TheoryThe fundamentals of equipment replacement theory grew out of the interaction between economics, engineering and finance. The use of annual cost comparisons and rate-of return calculations were helpful in handling situations in which assets with different finite lives were being compared. Later developments bringing together the concept of economic life and marginal analysis helped provide additional refinements to the theory. Taylorui showed that the displacement of an aging asset with a similar, but newer, asset can be justified economically when the marginal cost of keeping the asset one more year exceeds the minimum uniform annual cost equivalent of the proposed replacement."

Jan 1, 1980

By T. A. Rickard

Among the names which won a world-wide fame during the golden age of the early fifties, Bendigo and Ballarat were to Australia, what the Yuba and Grass Valley were to California. The map of Victoria did not for a long time show the name of old Bendigo;* for this first and more distinctive name was replaced with the more English Sandhurst, just as the alluvial diggings gave place to quartz mining. Towards the close of last pear, steps were taken to give back the old name, as associated with the early days of rich alluvium, and more suggestive than the application taken secondhand from an English military academy. History. The first discovery of gold? in this district, was made in the autumn of 1851 ; but there has never been any certainty as to the day or the man. At that time the country around Bendigo Creek was a part of the Ravenswootl sheep-run, and its resemblance to the Forest Creek district (now Castlemaine), induced the first prospecting. It was late in November when the "rush" broke out; the shepherds left their flocks; the sylvan solitudes were disturbed by * The name of Bendigo is said to have been derived from a hut-keeper on the Ravenswood sheep-run, who on account of his fondness for " fisticuffs " was nicknamed Bendigo, after the prize-fighter of that name. It is not aboriginal, as is often supposed, but Spanish ; and equivalent to our Benedict. There must always be some confusion between the two names of Sandhurst and Bendigo; the town, and with it the gold-field, having been three tinies named. Several other old familiar names have been likewise unfortunately replaced by second-hand English ones; so that an old digger talks of Forest Creek when he means the modern Castlemaine, Mt. Ida for Heathcote, Growler's Creek for Bright, etc. I shall use the names Sandhurst and Bendigo interchangeably. The first discovery of gold in Australia, was made by E. H.Hargraves, February 12, 1851, near Bathurst in New South Wales. In August of the same year the discovery at Buninyong, near Ballarat, inaugurated the first of a series of rushes to the Victoria gold-fields.

Jan 1, 1892

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

Introduction Aggregate mining impacts on water resources are a source of concern to local governments. To evaluate those impacts, the Minnesota Department of Natural Resources conducted a four-year study at three gravel pits (two alluvial and one beach-ridge) and five quarries (flat-lying Paleozoic limestone). This research provides the first comprehensive look at aggregate mining impacts on ground-water systems in Minnesota. The results will be used by government officials making permitting decisions about aggregate operations and by responsible owners of aggregate mines as they plan their operations to avoid conflicts with neighbors and with resources dependent on ground water and surface water. Natural aggregate (crushed stone, sand, and gravel) is a vital part of our economic infrastructure in Minnesota. Aggregate is used for road and bridge construction and in a variety of building materials. In 2003, the value of construction sand and gravel and crushed stone in Minnesota was approximately $245,000,000. As Minnesota’s economy continues to expand, the demand for aggregate will continue to grow. Sand and gravel pits are located in every county in Minnesota. In 1990, the Minnesota Department of Natural Resources, Division of Minerals (DNR Minerals), estimated the number of active and inactive operations at 1500 with the view that this number was likely too low. Quarries for mining limestone, dolomite, sandstone, and hard rock (granite and quartzite) are found in 34 counties. A 1990 DNR Minerals inventory found 165 active operations, 88 percent of which were limestone quarries (Nelson and others, 1990). That same inventory counted 1,367 inactive operations, 70 percent of which were limestone quarries. Aggregate mining is an extractive use of resources: mining alters the landscape and its natural hydrologic system. When a new pit or quarry is proposed or when an existing operation needs to expand, local governments and citizens typically have many questions about the impacts mining might have. Local governments, which are responsible for reviewing these operations, rarely have the budgets to hire experts to evaluate potential impacts of quarry and gravel pit proposals. The Minnesota Legislature’s Aggregate Resources Task Force identified that local government units (LGUs) often lack the expertise to assess ground-water models (Southwick and others, 2000).

Jan 1, 2007

By Edward J. Chuhta, Joseph E. Chilton, Robert J. Timko

in underground mines to measure worker exposure to various gases such as methane, carbon monoxide, and nitrogen dioxide (NO2). Even in relatively small concentrations, NO2 can produce harmful side effects in underground workers. Mines using equipment powered by diesel engines, carrying out explosive blasting operations, and performing extensive arc welding and/or cutting work will have measurable quantities of NO2 released by these processes. Workers in these areas often use gas monitors to warn of excessive gas concentrations and to help them determine when to increase ventilation air that will dilute these gases, thus minimizing exposures to this gas. Portable gas monitors, used to measure NO2 levels, must be calibrated before each use. Calibration is typically performed using a small portable pressurized cylinder containing a certified gas mixture. The certified NO2 standard mixture, usually 10 ppm NO2 concentration, is diluted with either air or nitrogen gas. To determine the stability of commercially available portable gas standards, two different cylinders containing NO2 in nominal 10-ppm concentrations were examined. One cylinder was diluted in air, the other, in nitrogen. Baseline NO2 mixtures were generated using a standard liquid NO2 permeation tube operated at a constant temperature. Final dilutions of the test gas mixtures were made with air or with nitrogen using a mass flow-controlled gas dilution system. This study showed that, when a permeation-type NO2 generator is used, the electrochemical sensors in portable NO2 monitors provide identical results for gas mixtures whether they are diluted with air or with nitrogen. Two different gas monitors, one with a two-electrode sensor and one with a three-electrode sensor, were used to measure gas concentrations in the two commercially available cylinders. One month after the cylinders were delivered, the NO2-in-nitrogen cylinder, stated to contain 10 ppm NO2, measured 8.13 ppm. The NO2-in-air cylinder, also stated to hold 10 ppm NO2, measured 6.88 ppm. Therefore, before using NO2 gas cylinders to calibrate monitors, it is recommended that their concentrations be verified either by manufacturer recertification or by comparing the stated cylinder gas concentrations to a laboratory-based permeation tube-generated standard.

Dec 1, 2005

By A Bouazza, J Kodikara

In this study, 23 samples of leached ash (LA) were collected from an ash pond at Loy Yang Power Station and geotechnically characterised. The samples were collected at various depths and locations within the ash pond on two separate occasions in order to account for the full variability. The LA within the ash pond at Loy Yang Power Station (LYPS) was found to vary in texture from silt to sand, depending on the location from where the sample was collected. Samples collected near the ash pond inlet discharge point, for instance, contained more than 50 per cent sand sized particles and were subsequently classified under the Unified Soil Classification System (USCS) as silty sand (SM). Further downstream of the inlet discharge, the LA became progressively finer and was classified accordingly as elastic silt (MH) when the sand content became less than 50 per cent. Basic geotechnical testing revealed that the LA from Loy Yang Power Station was generally acceptable as a landfill cover material. The permeability of LA, however, was generally too high for prescriptive covers, (ie resistive covers that generally rely on the impervious nature of the material to control percolation). Alternative covers, generally rely on the store/release function of a capillary or monolithic barrier to prevent percolation into the landfill. Subsequently, a material that can maintain a high water storage capacity while at the same time, readily allow infiltration and evapotranspiration is required for an alternative cover. Sandy silt and silty sand are optimal soils for alternative covers, as they do not yield water to gravity forces, but do give up most of the water in their pores when subjected to high-matric suction (Kavazanjian, 2001). The effectiveness of alternative covers is ultimately assessed using computer models, such as UNSAT-H and HYDRUS-2D, to rigorously perform water balance calculations. Prior to using a computer model to determine the highest possible percolation in the worst climatic conditions, it is necessary to select the most appropriate materials. This paper suggests a method to screen available materials for use as an alternative cover material on the basis of the soil water characteristic curve (SWCC).

Jan 1, 2003

By J. B. Gayle

PRESENT flotation processes depend almost entirely on the buoyant properties of air bubbles to effect separations of mineral and gangue, but there is no convenient method for measuring aeration in flotation cells. Consequently the relation between aeration and cell performance has not been definitely established. In connection with a comparative study of kerosene and froth flotation processes, a modification of the displacement method' was developed in which air escaping from the cell surface is measured with a wet-test meter. The arrangement shown in Fig. 1 is satisfactory for use with a number of cells and is not critical, except that care must be taken to use connections and tubing large enough to avoid excessive back pressures. Attempts to use smaller tubing resulted in back pressures that caused displacement of the liquid level in the receiver, so that some air was lost around the sides, an occurrence readily visible when measurements were taken with only water passing through the cell. With the arrangement shown, the manometer indicated an average reading of about 1/2-in. water pressure. No loss of air was evident. Fig. 2 presents typical data for a standard Denver sub-A 24x24-in. unit cell operated at impeller speeds from 0 to 710 rpm. Each plotted point represents the average for five readings distributed over the entire cell surface. Readings were taken with only water passing through the cell. Results of this type have been used in a study of the influence of operating variables on cell performance and in detecting inherent differences in the operating characteristics of cells of various kinds. Although the information presented in Fig. 2 resulted only with water passing through the cell, the apparatus is suitable for use during flotation of coal when various reagents are present. Possible modi- fications that might prove convenient under special circumstances include varying the size and shape of the receiver and substituting a calibrated, inverted, water-filled carboy or other gas-measuring device for the wet-test meter. If such modifications result in excessive back pressures, some form of draft should be applied at the discharge end of the measuring system.

Jan 1, 1959

By M. Javier

This concept paper is presented in the hope of raising the awareness of mankind on the necessity for its peaceful coexistence with nature. It is a food for thought. It takes compromise and sacrifice of people, who will have to learn to curb their greed and move toward a more organic form of prosperity. A nature-friendly sustainability is first step toward the protection of nature that is critical to the mutual survival of mankind and nature. People need the resources from the finite earth to survive and nature needs the prevention of human destruction in order to continue to regenerate and provide. The contemporary notion of sustainability is self-serving. It serves the interest of industry by camouflaging itself to look like nature?s protector. The ?sustainability? concept presented in this paper aims to extend the longevity of the utilization of the limited natural resources for many generations to come. It is an important, responsible first step in creating a healthy sustainability concept that, when implemented, extends the longevity of mankind by the most efficient use of the finite resources on this limited Planet Earth, all the while taking into consideration the increase in anthropogenic activities due to exponential human population growth. This new definition of ?sustainability? has completely different characteristics than its contemporary versions. Nature has its own destiny, rules and principles. Being a part of nature, human society depends on it for survival and must play by its rules and never the other way round as in its initial pretensions. Society should not try to humanize nature, but rather to respect the rule of the nature in a peaceful way of co-existence. When implemented, this new concept of sustainability aims to affect the designs of engineered structures and revolutionize the recovery methods and processing of natural resources, such as mineral resources in the most efficient manner. Finally, this paper intends to stimulate critical thinking and initiate serious discussions aiming at producing a general consensus for the best definition for human society to not only enrich, but to extend its existence. Thus, the spirit of this new definition is pro future generations and environment. KEYWORDS: Sustainability Definition, Nature, Geomímic, Deproduction.

Feb 27, 2013

By Karl Hoover, Cassandra Spence, Brent Bachewich, Jaakko Levanaho

"Since year 2000 the gold recovery into copper concentrate at Hudson Bay Mining and Smelting has reduced considerably during the summer months. This initiated a testwork program in the fall 2003 to find reasons and solutions for such change. During the testwork mineralogical factors, water quality effects and different reagents were evaluated. The reason for the lower recovery appeared to be the sensitivity of some collectors to pulp temperature. As a result of the work different collectors are being used in the mill in the summer than in the winter. A modification to the water system was also made to provide cooler water to the mill in the summer months.INTRODUCTIONHudson Bay Mining and Smelting (HBMS) is located in Northern Manitoba, just on the border of Manitoba and Saskatchewan. The complex consist of four different mines, Callinan, Trout Lake, Konuto Lake and 777 mine including copper smelter and zinc hydrometallurgical plants producing metallic copper and zinc. Gold is a very important byproduct providing about 30% of the mine revenue. In early 1990s when the company was facing declining ore reserves and was starting to gradually close down the operations, the 777’th exploration drill hole discovered a new orebody, which initiated a $0.5 billion expansion program. The main projects were a new 777 hoist with underground development and a new zinc cell house. About $30 million was used to increase the mill throughput to the present 2.27 million tonnes or 2.5 million short tons per year. The expansion programs were finished by the end of the year 2003.Historically the gold recovery at HBMS has varied between 60 and 70%. The recovery has been somewhat lower during the summer months. Gold recovery improvement projects were conducted throughout the 1990s, but were not focused on the seasonal gold recovery variance. However, since 2000, when the water system modifications to meet the increased water demand were completed, the gold recovery during the summer has been much lower than in the past. In August 2003 gold recovery fell below 30%, which initiated a metallurgical research program to discover the reasons behind the low gold recovery in the summer."

Jan 1, 2005

By Mohamed A. Younis, Paul J. Headland, Paul H. Madsen, Vojtech Gall

INTRODUCTION A 100 ft long, 20 ft high and 18 ft wide NATM tunnel was excavated through grouted clean sands beneath a busy city street, including a variety of existing utility lines. The new tunnel associated with a hospital expansion will serve as a pedestrian tunnel connecting a parking structure with a new hospital facility. Tunnel construction started on December 15, 2005 when drilling for the grouting program started and was completed on May 26, 2006 when the tunnel final lining was completed. The tunnel was constructed by Kiewit Construction Company as a tunnel subcontractor to The Christman Company who is constructing the hospital facility for Spectrum Health in Grand Rapids, Michigan. URS was the project designer. GallZeidler Consultants, LLC were the contractor’s NATM consultant. PROJECT DESCRIPTION The Michigan Street Pedestrian Tunnel is a component of the Michigan Street Development located along the north side of Michigan Street NE between Coit Avenue NE and North Division Avenue in the downtown area of the Grand Rapids, Michigan. The Michigan Street Development includes a parking deck and four new towers to be constructed over the proposed parking deck. The tower planned furthest east is being developed by Spectrum Health as the Lemmen-Holton Cancer Pavillion. The purpose of the pedestrian tunnel is to connect the proposed Lemmen-Holton Cancer Pavillion with the future Spectrum building to be located on the south side of Michigan Street NE. The southern end of the tunnel was constructed with a bulkhead until the future Spectrum building is constructed at which time interconnection will be required. The tunnel site plan and profile are shown in Figure 1, Site Plan, and Figure 2, Tunnel Profile. Several challenges were faced during the design and construction of the Michigan Street Pedestrian Tunnel. These challenges included compressed design and construction schedule, maintenance of traffic and protection of old underground utilities. The tunnel was being constructed as part of the Michigan Street Development and coordination with other concurrent construction activities was required. The tunnel was constructed within a specified window of time to allow other associated construction activities to take place without compromising the overall project schedule. The design started in June 2005 and construction was completed by June 2006.

Jan 1, 2007

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By F F. Pitard

The optimization of metallurgical processes requires knowledge of the heterogeneity carried by constituents of interest. The common scenario, almost an industry standard, is to rely on the engineering firm who in turn relies on favorite manufacturers of sampling equipment to provide the appropriate sampling systems in the plant to perform accurate metallurgical accounting. This sequence is flawed from the beginning to the end because everything should be based on a careful understanding of the Theory of Sampling (TOS) by the company project team and their expert who invariably would suggest various approaches and different sampling systems.The necessary progressive and iterative approach should be that the company’s project team (mining or other industries) would do its home work to have a good understanding of the geometallurgy, mineralogy and texture of the ore in each geological unit so consultants and engineers would have the best information to start with. Then a reputable sampling expert would recommend which sampling systems are needed, so the company would require engineering firms to follow pre-established, non-negotiable requirements, and finally select the sampling equipment existing on the market today that is most likely to lead to accurate and precise enough metallurgical accounting.It is the author’s experience that when this necessary progressive and iterative approach is bypassed, sampling systems installed in the plant are likely to transgress the most elementary rules of sampling correctness. Invariably the argument is that the company cannot afford correct sampling systems for metallurgical accounting as suggested in the Theory of Sampling. There is nothing that is farther from the truth when later problems will develop and inevitable reconciliation difficulties with miners and geologists become daily routine with impossible answers; as a last resource the sampling expert may be called to perform a post-mortem analysis.The progressive and iterative approach suggested in this paper should be a due diligence requirement for any bank providing a loan for an important new mining project; anything less is most likely to generate unpleasant financial losses; historical, well-known examples are referred to.CITATION:Pitard, F F, 2015. A progressive, iterative approach leading to reliable metallurgical accounting sampling systems, in Proceedings MetPlant 2015, pp 78–91 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By D. Mkhwanazi

The purpose of the project was to optimize load haul dump (LHD) machinery use as they were spending too much time doing what they should not be doing. During the investigation, the author found that the machine's actual availability was 86% and the utilization ranged between 30% and 42%. This shows that the availability of the machine has met its target. Therefore the main problem was with the LHD utilization and that is what the project focuses on. To satisfy the objectives, the author firstly studied the existing mining data like the key performance indicators (KPIs) in order to analyse the machine's availability and utilization; this is what gave direction to the problem. Secondly the author did a literature review on mines with similar problems. This gave the author ideas on what to look at in approaching such a situation. Thirdly, the author gathered information on what the LHDs are doing on a daily basis by doing a time study. This gave the author an idea of how long it took the LHDs to complete a specific task. The author also interviewed operators and their supervisors in order to find the best practice work. This helped in identifying the problem areas when comparing the best practice work with what the LHDs are actually doing. According to the project results, it was found that the LHDs are underutilized due to shortage of drivers and the long distances the LHDs have to travel for material loading and refuelling. The author recommended that the machine utilization should be improved by training more operators in order to eliminate the 'no operator' downtime; the cost arrangement of this recommendation is included in the report. The author also recommended that the travelling time should be reduced by using tractors instead of LHDs when long distances need to be travelled for material loading. Another recommendation for reducing travelling time was to bring the mobile fuel tank closer to a section; the cost arrangement for this recommendation is also included in the report. Keywords Optimizing, LHD utilization, LHD availability, key performance indicators (KPI), shortage of drivers, long distances, mobile fuel tanks.

Jan 1, 2011

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951