Search Documents

By J. H. Yang, K. E. Gray

Results of single-blow bit-tooth impact tests on saturated rocks under elevated confining pressures and zero pore pressure were reported in a previous publication.1 This paper presents an extension of the earlier work to include a study of crater formation during tooth impact on both gas- and liquid-saturated Berea and Bandera sandstones at elevated confining and pore pressures. The basic data obtained were force-time, displacement-time, velocity-time and force-displacement curves during crater formation. Crater volume was also measured and the mode of crater formation determined. Bit tooth geometry, depth of penetration and velocity of impact were held constant. Results indicate that, with pore fluid present in the rock, failure trends from brittle to ductile as pore pressure is increased at constant confining pressure (pore pressure and borehole pressure were equal) For a given rock type, the mode of crater formation was dependent not only upon the nominal effective stress, but also upon the fluid which saturated the rock pore space. When confining pressure and pore pressure were equal (zero nominal effective stress), bit-tooth impact resulted in brittle failure for nitrogen-saturated Berea, and brittle to transitional failure for nitrogen-saturated Bandera; when saturated with liquid both rocks failed in a ductile manner at zero nominal effective stress. INTRODUCTION Dynamic wedge penetration tests have been conducted by investigators in several fields, but the failure mechanism of rock under dynamic stresses is not understood completely. The complex action of drilling bits, even considering the action of a single tooth, may be considered as a combination of drag bit and rolling cutter action. Thus, as a first step in understanding rock breakage in oil well drilling, single chisel impact and rock planing are of fundamental importance. For example, Gray 2 and Crisp3 studied drag bit cutting action at brittle stress states. Simon4 and Hartman5 studied the reaction of rocks to vertical impact by means of drop tests. The depth of penetration, crater volume and force-vs-time curves during crater formation were observed. The significance of indexing single-bit impacts has been noted.4,6-8 Gamer et al,9 reported impact tests on impermeable Leuders limestone at atmospheric and elevated confining pressures. In all cases the tests were accomplished on dry rock and pore pressure was considered to be zero. The importance of both confining pressure and pore pressure on the failure characteristics of rock was described. 10-12 It was found that the yield strength and ductility of porous rock depend on the state of stress under which the sample is tested. The importance of pore pressure on drilling rate in microbit experiments was noted by Cumingham and Eenink. l3 Robinson 12 also pointed out that in drilling the most important parameter in rock failure is the effective stress, where effective suess is defined as confining pressure pc minus pore pressure pp. The effect of pore pressure and confining pressure on rock strength was also noted by Serdengecti and Boozer 14 in strain rate tests, and by Gardner, Wyllie and Droschackl5 in elastic wave studies. Until recently all reported wedge impact studies under simulated wellbore stress states have been conducted on dry rock. Maurer 16 reported impact tests on samples saturated with deaerated water. Borehole and formation fluid pressures were equal in these tests except when mud was used in the borehole. With mud in the borehole and a high borehole-to-formation fluid pressure differential. Maurer observed "pseudoplastic" crater formation. Podio and Grayl reported impact tests on Berea and Bandera sandstone saturated with pore fluids having wide ranges in viscosities. In Podio and Gray's tests, confining pressure was elevated, but pore pressure and borehole pressure were held fixed at atmospheric pressure. The presence of

By C. R. Ramachandra, C. C. Patel

Flotation of chalcopyrite from a low grade ore was studied by using different xanthates and dixanthogens as collectors and by conditioning the flotation pulp with oxidizing gaseous systems. The improvement in the recovery of chalcopyrite with the oxidizing systems was mainly due to the auto-activation of chalcopyrite, leading to the enhanced adsorption of xanthates and dixanthogens even when the latter were formed by oxidation of the xanthates. With air or oxygen as oxidizing system, the amount of ethyl xanthate required at pH 8.5 was much less than normally employed in the industry, the recovery being 97-99% of chalcopyrite with a concentrate of 24% copper. With isopropyl and isoamyl xanthates, the recovery was improved but the grade was lowered. By conditioning the pulp with air-CO2 or oxygen-CO2 mixture, the recovery was lowered with ethyl xanthate only, mainly due to the depressant action of bicarbonate formed. Flotation with dixanthogens gave cleaner concentrates of chalcopyrite. because iron pyrite did not float with these collectors. Of the dixanthogens tried, diisopropyl dixanthogen gave the highest recovery, 99% chalcopyrite with a concentrate containing 28.5 to 30% copper, when the pulp at pH 8.5 was condi-tioned with air. Isopropyl dixanthogen was found to be the best collector of all the xanthates and dixanthogens studied. It was found that the adsorbed ethyl, isopropyl and isoamyl xanthates at chalcopyrite surface, activated by cupric sulfate, and at iron pyrite surface were oxidized to the corresponding dixanthogens to different degrees in presence of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture.' The dixanthogen formed at chalcopyrite surface was, however, firmly adsorbed while that at iron pyrite surface was easily desorbed. Since dixanthogens formed have greater hydrophobicity than the corresponding xanthates, as revealed by contact angles,1,2 the former were expected to improve the flotation results. It was, therefore, thought desirable to find out the effect of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture on the selective flotation of chalcopyrite when individual xanthates were used as collectors. The effect of direct use of dixanthogens as collectors on the selective flotation of chalcopyrite was also investigated. For these studies, low grade chalcopyrite ore, received from the Indian Copper Corp., Ltd. (I.C.C.), Ghatsila, Bihar, was employed. At the milling plant of the I.C.C., chalcopyrite is floated at a pH of 8.5, employing ethyl xanthate as collector. EXPERIMENTAL Materials Employed: XANTHATES - Ethyl, isopropyl and isoamyl xanthates of potassium were prepared in a pure state by the methods described earlier.4 A 0.03% aqueous solution of a xanthate was freshly prepared in air-free distilled water for flotation studies. DIXANTHOGENS - Diethyl, diisopropyl and diisoamyl dixanthogens were prepared by the oxidation of xanthates by iodine and purified by extraction with petroleum ether. A 0.03% alcoholic solution of dixanthogen was used as a collector. FROTHER - A 0.2% solution of pine oil in ethyl alcohol was employed. SODIUM CARBONATE - A 0.4 N solution was used. ORE - The composition of the -100 +200-mesh size (Tyler standard) powdered ore, as determined by standard methods of analysis, was: copper 1.57%, iron 10.29%, sulfur 3.15% and acid insolubles 66.10%. Iron present as chalcopyrite (CuFeS2) was 1.38%, while that present as iron pyrite (FeS,) was 1.37%. Both chalcopyrite and iron pyrite were found to be liberated from the gangue minerals and from each other, as observed under a microscope. Flotation of Chalcopyrite with Xanthates in Presence of Different Gaseous Systems: Fifteen grams of -100 + 200-mesh size ore were shaken well with 100 ml of distilled water. The pH of the pulp was adjusted to 8.5 by the addition of sodium carbonate solution. Then 0.1 ml of xanthate solution (0.005 lb xanthate per ton of the ore) was mixed with the pulp, and the latter together with washings transferred to a

Jan 1, 1963

By S. K. Mitra

A refinement of the Seeger model for intersection process is investigated which is in better agreement with experimental observations than the original. It is shown that, in single crystals, the strain hardening in Stage II is mainly due to the short-mnge interactions when intersection is the rate-controlling process. It is also demonstrated that the creep curves, as predicted by this theory, are in good agreement with the experimental observations. MOTT: Cottrell? and Seeger have developed an approximate theory for plastic deformation of single crystals over the range of variables where the strain rate is controlled by the rate of intersection of dislocations. Although it is now generally agreed that the low temperature deformation of many pure metals is controlled by the intersection mechanism, various dictates of the over-simplified Seeger model are not in good agreement with all the experimental facts. It is the purpose of this paper to reveal that by appropriate extensions of the Seeger model, particularly those suggested by Basinski: a much more reliable theory results. The refined model to be presented here will be shown to account, in a satisfactory way, for the effect of stress, temperature, and strain on the creep rate under constant stress and for the effect of temperature and strain on the flow stress in constant strain-rate tests. EXPERIMENTAL METHOD To Check the theoretical deductions, both creep and tension tests were conducted on single crystals of high-purity Al (99.994 pct Al) so oriented that both the active slip plane and the Burger's vector of the operative dislocations on that plane made angles of about 45 deg to the tension axis. Single crystals of aluminum (5/8 in. by 1/10 in. by 8 in.) were grown in a graphite mold under an inert atmosphere using the Bridgman method. The chemical composition of the aluminum is given in Table I. A common seed was used for all crystals and their orientation is shown in Fig 3. The extensometry consisted of two differential transformers with matched outputs mounted so as to measure the extension in a 2 in. gage length. The amplified difference in output of the two transformers was recorded by a potentiometer. The amplification was calibrated before each run so that one chart division of the recording potentiometer indicated a 105 shear strain on the specimen. Stresses were measured to the nearest 1 x l04 dynes per sq cm. ACTIVATION VOLUME The concept of Basinski that the activation volume is not constant but is a function of the force that aids thermal fluctuation in effecting the cutting of dislocations will be adopted in this section. The force acting due to an applied shear stress on the dislocation being intersected is where L is the mean spacing between the forest dislocations, is the Burger's vector and T is the back stress. A detailed discussion about the origin of back stress will be taken up later in this report. As shown by Basinski, the activation energy, U, that must be supplied by a thermal fluctuation in order to effect intersection, is equal to where x is the distance through which the dislocation must be translated for complete intersection, and Fm is the maximum force encountered in intersection. When the applied stress is decreased abrupt ly F also decreases and the activation energy increases correspondingly as documented in Eqs. [ 1 ] and [2]. The Seeger equation for the strain rate when the deformation is controlled by rate of intersection of where the shear strain rate (per sec) N = the number of points per unit vol at which intersection can take place

Jan 1, 1962

By I. R. Kramer

The stress associated with the high-dislocation layer at the surface of deformed aluminum crystals was measured by progressively polishing the specimen and determining the change in the initial flow stress when the specimen was reloaded. This surface stress increased linearly with strain in the Stage II and Stage III region. The depth to which the high-dislocation layer extends was found to be 0.0025 in. The influence of the surface layer on Stage I is discussed and it is shown that Stage I ends when, on the secondary slip system, the difference between the applied stress and the opposing stress due to the surface layer is equal to the critical resolved shear stress. In previous papers'-3 it was shown that the surface exerts a pronounced effect on the plastic-flow characteristics of metals. For fcc metals it was possible to increase the extent and decrease the slope of Stages I and II and decrease the work-hardening coefficient of Stage II by removing the surface of the specimen continuously during the deformation process.2,3 More recently,L it was shown that the activation energy for plastic deformation and the activated volume were also influenced by the surface. These changes were related to the existence of a high concentration of dislocations in the region near the surface of the deformed specimen and it was concluded' that the effective stress, T, acting on a dislocation was T = Ta-Ti-Ts [1] where 7, is the applied shear stress, Tj is the internal stress, and TS is the stress associated with the surface region containing the high concentration of dislocations. From Eq. [I] it is seen that the effective stress, 7, acting on a dislocation is a function of 7,. Therefore 7, becomes important in any description of the work-hardened state. In this paper the value of 7, as a function of strain and its variation with depth are reported for aluminum single crystals. In particular, it will be shown that the end of Stage I occurs when the net stress, 7, on the secondary slip system is equal to the critical resolved shear stress. To measure Ts, single crystals of aluminum were deformed in tension to various strains, whereupon the load was removed and a known amount of metal was removed by electrolytic polishing. The differ- ence between the final flow stress before the specimen was unloaded and the initial flow stress upon reloading is designated as ?Tp and is the decrease in the stress due to the removal of the surface layer in whole or in part. The value for Tp is taken equal to -Ts. EXPERIMENT PROCEDURE The details of the tensile apparatus, method of electrolytic polishing, and crystal preparation were the same as those used previously,1"3 The single crystals were 1/8 by 1/8 in. in cross section with a 3-in. gage length. The initial purity of the aluminum was 99.997 pet. The specimens were held in vacuo at temperatures 50°C below their melting points for 16 hr and furnace-cooled. Just prior to the application of the tensile stress the specimens were electrolytically polished to remove 0.004 in. from the thickness. This latter operation was conducted after the specimen was placed in the tensile apparatus. The tensile tests were conducted at a strain rate, i, of 10"5 sec-' and a temperature of 3°C. The aluminum crystals used for the determination of 7, are designated A1-3-12 and A1-116. The orientation of the various crystals used throughout the investigation is shown in Fig. 1. The ?Tp values for specimens A1-3-12 as a function of Ax were determined mainly at four strain levels, i.e., ? = 0.0217, 0.0381, 0.0593, and 0.075, where Ax is one half of the total reduction of the thickness after polishing and ? is the re-

Jan 1, 1965

By A. M. Rowe, I. H. Silberberg

A computer program was written to predict the phase behavior generated by the enriched-gas-drive process. This program is based, in part, on a new concept of convergence pressme, which is then used to select vapor - liquid equilibrium ratios (K-factors) for performing a series of flash calculations. The results of these calculations are the equilibrium vapor and liquid phase compositions which define the phase envelopes. The program was used to predict phase envelopes for 11 different hydrocarbon systems on which published experimental data were available. The predicted and experimental results compare favorably. INTRODUCTION The reservoir engineer is frequently faced with the problem of predicting what will happen if gas is injected into a reservoir. One aspect of this, general problem is predicting the phase changes that will occur when a non-equilibrium gas displaces a reservoir fluid. In particular, a "dry" gas, upon displacing a volatile oil, will pick up intermediate components from the oil. On the other hand, a "wet" gas, containing a high concentration of intermediates, will lose some of these components to a relatively low-gravity, non-eouilibrium1- crude. It is this latter Drocess. occurring in the enriched-gas displacement, which is treated in this paper. In the past, these phase changes have been determined experimentally and the results incorporated into various modifications of the Buckley-Leverett analysis.112 Such experimental work is time consuming, and the results are sensitive to numerous experimental errors. With the wide availability of high-speed digital computing equipment and numerous correlations pertaining to the vapor-liquid equilibria of hydrocarbon systems, it is now practical to calculate such phase behavior. This paper describes a computer program for performing these calculations. THE ENRICHED GAS DISPLACEMENT PROCESS Experimental results have shown that oil recovery can be significantly increased by enriching the displacing gas with intermediate hydrocarbon c0m~onents.3 The essential features of the phase behavior generated by this enriched-gas-drive process are commonly illustrated with ternary diagrams such as Fig. 1.4 In this figure, Gas D, which contains a high concentration of intermediate hydrocarbons with respect to the undersaturated Crude A, is injected into the reservoir. When D contacts A, gas goes into solution until the oil becomes saturated (Point. B). Further contacting of Gas D and saturated Oil B results in a Mixture C which separates into Vapor Y(c) and Liquid X(c). Liquid X(c) is contacted by additional Gas O, resulting in Mixture E which separates into Vapor Y(e) and Liquid X(e). Repeated contacts of the liquid by the injected gas will eventually result in Liquid X(4 of maximum enrichment existing in equilibrium with Gas Y(d). The equilibrium tie-line X(4 Y(4, when extended, passes through the Point D representing the enriched injection gas. For systems of more than three components, the predicted equilibrium states are dependent upon not only reservoir temperature and pressure, but also the compositions of the crude oil and injected gas. If the gas is sufficiently enriched, a miscible displacement is generated. Line If is tangent to the phas,e envelope at the critical point (Point Z) and represents the limiting slope of the tie-lines as the critical state is approached. Point 1 therefore represents the minimum enrichment of injection gas required to generate a miscible displacement. Point G represents the minimum enrichment required for initial miscibility of the injection gas with Crude A. Accra has presented a method to be used for prediction of oil recovery by the enriched gas displacement process.l To develop the phase behavior data needed, he designed the experimental procedure described in the following quotation from his paper: The original liquid was contacted by a volume of displacing gas and allowed to come to equi-

Jan 1, 1966

By C. Tom Blevins

The purpose of this paper is to discuss production and roof control problems associated with directional lateral stresses in an in situ stress field and the approach that Inland Steel Coal Company made in trying to cope with them. Before proceeding, a description of the mine location, product, geology, restraints, and mine history is in order. The mine is located in Hamilton County in Southeastern Illinois. It produces a high volatile metalurgical coal and is slated to produce 2.1 MTY. Product ion is in the Illinois No. 5 seam at a depth of 930 feet, approximately 490 feet below sea level. The scam height averages from 5.5 to 6.0 feet throughout the reserves with height increasing in the eastern reserve area to approximately feet and a 5 Foot average in the West. The scam tends to dip to the North, North East, but is locally very undulating. The Galatia channel washout outlines the eastern boundary of the reserves and there is a split coal area toward the central part of the property than runs south-southeast. The top above the #5 seam is laminated medium gray shale called Dykersburg. Individual shale bedding planes vary locally From ½ to 1" in thickness to a more normal thickness of 1 to 1 ½ with some areas being interlayed by thin carboncous material. The top normally must be considered as materially competent. Even though the mine is still relatively small in area with only 1.3 million tons of total production to (late, we have encountered dense zones of slicker sides and premining, stress cracks (joints). There are also areas of siltstone, that vary from a few inches to several feet thick, and areas of rider coal, clay instrusions, and rolls. We have crossed lineament concentrations that show strong evidence of corelation to localise top problems. These are being monitored closely to see their predictability on our present and future mining conditions. The face cleat runs N 55° E and butt cleat runs S. 25° E. On a regional basis, there are several anticlinal belts that trend in a northerly direction. The one major restraint is that Inland does not own surface subsidence rights. Therefore, a partial extraction mining plan is being followed. The Holland-Gaddy formula for pillar strength design is used to calculate theortical pillar sides. When production began in March of 1979, it was noted that ground control problems occurred as we drove north entries. East-west cross cuts tended to have better working conditions. This phenomia occurred from a couple hundred feet, but seemed to dispate as we got away from the men and material shafts. Once the production shaft was connected and enough entries extended for installation of belts, ground control problems were again experienced in north-south headings. It was also observed that when mining north-south headings with east-west crosscuts, if the crosscut was driven through ahead and supported, the intersection was stable upon entry connection. This held true even where fairly extreme ground control, problems were encountered. The reverse held true. when driving east-west headings with north-south crosscuts. At this time, we started searching in earnest for a working theory to explain this roof phenomia. It also became the first step of what eventually was a four step sequence to derive a workable solu¬tion to the problem. The combination of the many geological changes and the fact that north-south condition was at times intermitent, helped to disguise the stress field. The mine also being in a fairly virgin area with no mines in approximately 25 milt, radius, meant we didn't have a reliable case history to examine. Various theories were researched before it was concluded that our primary ground control problem was a directional lateral stress Field, with the major stress axis in an east-west direction. The second stop of the procedure was then to test. mining methods and determine if these stresses could be modified to a

Jan 1, 1982

By R. A. Salathiel, A. D. Kaiser, P. H. Monaghan, B. E. Morgan

The productivities of many hydrocarbon-bearing for-rnntions appear to be reduced during drilling, completing and repairing operations. The reason for these othcarwise unexplainable low productivities may be a drastic reduction of formation permeability immediately surrounding the borehole. A possible cause of the reduced permeability is swelling and dispersion of clays present in porous media when contacted by fresh water or mud filtrates. Hence, the invasion of fresh water or mud filtrate into hydrocarbon-bearing formations that contain clays may cause low productivities as a result of formation damage. Present laboratory investigations have yielded results which supplement existing literature on formation damage. An expanded-type clay, montmorillonite, way found in hydrocarbon-bearing formations not previously analyzed. When sand columns and formation cores containing montmorillonite were contacted by fresh water, their oil permeabilities were reduced. This reduction in oil permeability way restored partially but not completely by a repair procedure, i.e., flooding with kerosene containing organic agents or flooding with water containing electrolytes. Hence, where montmorillonite is present in formations, prevention of formation danzage was indicated to be the only complete solution to the problem. To prevernt formation damage, results suggested use of an approximately 1 per cent solution of calcium chloride or stronger solutions of sodium or potassium chloride. In conventional rotary drilling operations the wall of the hole is exposed to drilling mud for days, weeks, and in some instances for as long as several months. During this time, drilling mud filtrate seeps slowly into formations surrounding the hole. The permeability and stability of many formations, especially those containing clayey materials, are impaired by the mud filtrate. Often interaction between the mud filtrate and the formation causes drilling and production difficulties. Serious reduction in productivity of oil and gas formations during drilling, completing and repairing wells has been noted often in recent years. Cases are known of development wells which produced only small volumes of fluid upon completion. However, after a period had elapsed, they began to produce oil or gas in commercial quantities. In other cases, results of drill-stem tests taken during the drilling of deep wells have indicated good production should be obtained from shallow formations. Later difficulty has been experienced in obtaining production from these shallow formations which had remained in contact with drilling muds for an extended time. In yet other cases wells have failed to attain the productivities expected from previous performance after the use of drilling mud as a circulating fluid during workover operations. It is evident from the field behavior cited that the productivities of certain oil- and gas-bearing formations have been damaged by exposure to drilling muds. This reduction in well productivity, called "formation damage", causes serious consequences. In development wells, expensive remedial operations are incurred. In wildcat wells, good formations may appear to be marginal or even non-productive. The importance of formation damage has been recognized by a number of investigators1-s who have considered the effects of fresh water, saline solutions and aqueous mud filtrates on the permeabilities of formations. A general conclusion from such studies is that interaction between water and formation clays reduces permeability of reservoir rock and that the permeability decreases as salinity of the water decreases. Data in these references, however, concern the permeability change with only a single fluid present. A more pertinent and direct consideration in the production of oil and gas from wells is the permeability change when two fluids, oil and water, are present. Recognizing this, Nowak and Kreuger2 and Bertness1" considered several ways in which mud filtrates and saline solutions caused reductions in the oil permeability of formation cores. Investigations discussed here were designed to supplement information in the literature on changes in oil

By H. I. Kaplan, C. Laird

Pulsating contpresslon experiments have been carried out on coppev single crystals in order to test the adequacy of mechanisms which have been suggested for stage I cvack grouth when tension-compression loading is the mode of- applying stress. Although dejorrrzation continues slowly for many millions 01 cycles under Pulsating compression stresses both within slip bands formed in the first cycle and by the creation of new bands, the morphology of these bands is not typical of fatigue slip bands in general and neither initiation of cracks nor propagation of artificially induced cracks was observed. It is therefore concluded that 1) initiation and growth of cvacks in fatigue is a consequence of repeatedly reviersed, microplastic deformation rather than intermittent, unidirectional deforma-tion, 2) gvowth of- cracks in polycrystalline specimens FAILURE of a plain specimen subjected to cyclic tension-compression stresses is known to take place by two stages of cracking.1,2 The first stage is characterized by propagation along slip planes roughly at 45 deg to the stress axis, in the outermost layers of the specimen, and at a rate of the order of angstroms per cycle. The average macro orientation of a stage I crack is normally at right angles to the stress axis,3 however, except in a few cases, e.g., single crystals in suitable orientation, when both the micro and macro directions of propagation are at 45 deg to the axis. After a stage I crack has penetrated to such a depth that the stress on the remaining section of metal is significantly increased, stage II crack propagation succeeds stage I, at right angles to the stress axis both micro and macroscopically. Direct evidence of the processes occurring during a subjected to pulsating compression stresses is caused by the setting-up of local tensile stresses due to interactions between grains, and 3) both unslipping mechanisms and operation of the "plastic blunting process " within a single slip band are adequate descriptions 01- stage I growth, being fundamentally similar. The slip mode of a material, however, is considered to control whether unslipping or the plastic blunting process takes place. Thus materials of planar slip mode fauor unslipping while those hacing a wavy mode, and capable of cross slip, can fail in stage I by the plastic blunting process. Similarly, and perhaps more importantly, reversed torsion and tension-compression modes of applying stress may be expected to cause the unslipping mechanism and the plastic blunting process, respectively. single stress cycle4,5 shows that stage II crack propagation takes place by a repetitive plastic rounding and closing of the crack tip. This mechanism has come to be called the "plastic blunting process".6 On the other hand, the extreme smallness of the phenomena occurring in stage I growth prevents elucidation of its mechanism by direct observation. Many suggestions have been proposed for this mechanism,'"-" most of them involving some kind of random or systematic unslipping process. It is possible, however, that the mechanism of stage I growth is essentially the same as that of stage 11, but occurring on a much smaller scale.6 In this situation, it has been observed that cracks propagate along slip bands comprising dislocation cell structures and bounded on either side by regions of different dislocation density and distribution." Since there is evidence that such bands are softer than their matrix, * it may be expected that the plastic blunting process occurs within a single slip band during stage I growth, rather than on two gross bands as in stage 11, when the acting stress is greater.= The blunting of the crack tip allowed by coordinated

Jan 1, 1968

By R. P. Alger, C. A. Doh, M. P. Tixier

The principle, the equipment and field operation of sonic logging are described. The tfio-receiver system produces logs independent of hole size and mud. Field experience is given and forms the basis for the interpretation of the log. The derivaiion of porosity values from measured velocities is discussed, according to the type of formations (hard formations, compacted sands, and unconsolidated formations). The time-average equation proposed by M. R. J. Wyllie, A. R. Gregory and L. W. Gardner is uscd as a basis for the computation of porosity in limestones, cemented sandstones and compacted sands. Variations in the lithologic character of limestones do not seem to change the porosity calibration markedly. The compaction of sands is related to the compaction of shale adjacent to them; and, thus, the shale velocity is used for the establishtnent of empirical relations for the computation of porosity in un-consolidated formations. Various forrnu.las are tentatively presented to account for shale and fluid content. Field experience demonstrates that considerable attenuation of sonic energy takes place in unconsolidated formations, particularly when gas bearing, and in fractrured formations. Unusually large attenuation produces skipped cycles, a feature easily recognized. The application of sonic logging to structura1 studies is featured, showing its possible integration with the dipmeter. Correlation and its application to the irrterpretation of seisrmic surveys are reviewed. The paper is illustrated with field examples. Sonic logging is the recording of the time required for a sound wave to traverse a definite length of formation. Sonic travel-times are inversely proportional to the speed of sound in the various formations. The speed of sound in subsurface formations depends upon the elastic properties of the rock matrix, the porosity of the formations and their fluid content and pressure. Below the "weathered" or low-velocity layer extending from 50 to 100 ft or so below the surface, sound velocities may range from about 6,000 ft/sec in shallow shales to as much as 34,000 ft/sec in dolomites. In hard formations (well cemented and/or compacted), the sonic log reflects the amount of fluid in the formations; hence, it correlates well with their porosity. In unconsolidated formations, which are usually of fairly high porosity, the sonic log gives an approach to porosity determination, when its readings are corrected for lack of compaction, shaliness, and fluid content. In such formations the sonic log may also indicate the presence of gas and may distinguish between oil- and water-bearing beds. Field experience with the sonic log in soft formations is more limited than that in hard formations. As a result, interpretation in soft formations is not as well developed at the present time. In all types of formations the sonic log is of considerable value for correlation and for the more detailed and accurate interpretation of seismic data. EQUIPMENT AND PRINCIPLE FIELD OPERATION The basic features of the sonic log" are a two-receiver system and two available short spacings. The log is recorded on film using a standard field unit. An SP curve is run along with the sonic curve to give a more interpretable log and to establish absclute depth control for comparison with other logs run in the same well. If desired, a gamma-ray curve may be recorded simultaneously with the sonic curve. Fig. 1 shows the sonic-gamma ray combination sonde. The sonic portion consists of a sound transmitter and three receivers mounted 3, 4 and 6 ft from the transmitter. When the first and second receivers are used, a sonic log of I -ft spacing (distance between receivers) is obtainea. Use of the first and third receivers provides a 3-ft spacing. The transmitter emits pulses at the rate of l0/sec. After the transmission of a pulse the first arrival of sound energy at each receiver triggers its response system. The differ-

By F. C. Bond

Since the Third Theory of Comminution was presented eight years ago (I) it has found increasing use in crushing and grinding problems. The practical utility of its wok index equation is quite generally acknowledged (2). However, its theoretical basis has been questioned in at least three technical articles (3) (4) ('). The purpose of this paper is to present experimental proof that it is scientifically correct. Particles under compressive stress are strained and deformed. They absorb strain energy, and when this locally exceeds the breaking strength, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends and splits the rock, releasing the strain energy as heat. The initial energy flow causes additional crack tips in highly strained areas. If the compression is rapidly applied by impact, crack tips may form before the strain energy has reached equilibrium in the particle, thus decreasing the total work input required for breakage. The energy necessary to break is essentially the energy necessary to produce crack tips, since the energy necessary to extend the cracks to breakage is already present as strain energy in the deformed particles. After breakage nearly all of this energy appears as heat. The crack length cannot be measured directly. However, in particles of regular and similar shape the crack tip length is considered as equal to the crack depth, or crack extension necessary to break, so that the crack length equals the square root of one-half of the surface area. The Third Theory states that the useful work done in crushing and grinding is directly proportional to the total length of the new cracks formed. It can be confirmed by showing that a constant work input produces a constant length of new cracks when reducing the same material to different product sizes. This is done in the present paper on a wide variety of material. The constant work input was supplied by one revolution of the 12" x 12" laboratory ball mill used in making grindability tests by the Allis-Chalmers method (12) (13) The new crack lengths produced per mill revolution were measured from all available grindability test results at 28, 35, 48, 65, and 100 mesh on fifteen different ores, and were found to remain substantially constant for each ore at all mesh sizes. A new technique is used for the measurement of crack lengths. Size distribution plots of the mill feed and product are made by the Third Theory method (9) and the crack lengths are obtained from these plots by the procedure described in the present paper. The energy input required to produce a unit length is of fundamental importance in the size reduction of brittle solids. The crack length Cr is expressed in centimeters per cubic centimeter of solid material. It bears a definite relationship to the external surface area of the crushed or ground solid. A uniform particle shape must be assumed before the surface area and crack length can be evaluated. In this paper it is assumed that the relationship between the surface area and the particle volume of a particle d microns in diameter is the same as that of cube d microns on a side. The external surface areas of particles with a cubical breakage probably agree approximately with this rule, and correction factors can be applied when physical measurements of the surface areas are available for comparison. However, the assumption of equivalent cubes has been found satisfactory for most calculation purposes. Assuming equivalent cubes, one cubic centimeter of particles d microns in diameter will have a crack length Cr of v30.000/d centimeters, and a surface area of 60,000/d square centimeters. The specific crack length is thus equal to the square root of one-half the specific surface area. Where Sa is the surface area in square centimeters per gram and Sg is the specific gravity of the ground solid, then Cr = vSg . Sa/2 = 173.2/ vd (1)

Jan 1, 1961

By R. K. Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a cascading pillar failure, occurs when one pillar in the mine layout fails, transferring its load to neighbouring pillars and causing them to fail in succession. Recent examples of this kind of failure in coal, metal and non-metal mines in the USA are documented. Mining engineers can limit the danger presented by these failures through improved design practice. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This is used as a basis for three design approaches to control cascading pillar failure: containment with barrier pillars during pillar splitting; prevention with panel pillars of high width-to-height ratio and small-centre mining; and full extraction by retreat mining

Jun 19, 1905

By George L. Gates

[When clays are mixed with water to -.,tee mud fluids for use in trilling wells for nil and --ac b ;l-,e rotary method the liquid mixtures have certain physical characteristics that vary with the quantity and size of their inherent solid particles. All naturally occurring clays contain variable quantities of particles of different sizes ranging from relatively coarse (sands) through -,.tedium (silt) to fine materials of colloidal dimensions. Tie colloid content is extremely important 2.s a desirable _.'ale constituent of mud fl-z to fit well drilling. ';'it:-out colloids the souk?;,' in a mud fluid wouldr rapidly, end ti-c-and. wall-building qualitites of the' fl,-,id would l ..o r re 1 impaired. Mud .fluid.^ with insufficient quantities of colloids also are lacking in "lubricating" g listen, and it is, to ° min casing in, -)re holes drilled with such fluids.]

Jan 1, 1941

By Tyler Blake

This report describes a study designed to evaluate a pro-posed modification in the cap lamp battery cord intented to reduce the incidence of snagging and catching of the cord. A three phase evaluation was performed comparing a prototype with the standard, currently available cord. First, a ?pull test? equipment was run. The second evaluation was a body conformity study. The third evaluation involved subjects performing common tasks in a low seam coal mine simulator. The results of these evaluations clearly demonstrated significant safety advantages of incorporating coiled cord into the design of the cap cord. The coil cord presented less of a snagging hazard, allowed the wearer more time to respond to a snag, and transmitted lower levels of force to the helmet when snagged. The research team recommended that cap lamp cords be commercially developed which incorporate coiled cord at the battery and helmet.

Jan 1, 1980

By Daniel Ng

The U.S. Bureau of Mines-Michigan Technological University mine ventilation mainframe program was successfully adapted for execution in a personal computer (PC). The hardware requirement can be as modest as 256 kilobytes (33) of random access memory (RM) and two floppy disk drives. A version compiled for a PC possessing 512 Kb RAM has arrays dimensioned to accommodate 512 separate mine airways and junctions, and it contains all the features and capabilities of the original version. It has successfully analyzed all the ventilation networks tested, including a very large commercial mine (404 airways, 237 junctions, and 5 fans). In all cases the PC version produced practically identical results as obtained from the mainframe computer. In all respects, the PC version performed the same as the mainframe version with the exception of execution speed When a numerical coprocessor is employed, execution time can be reduced by more than 50%.

Jan 1, 1989

By Mark Sanders

This report compares a proposed 10/60 "piggyback" 02 generating self-rescue unit to the standard CO self-rescue unit with respect to work task interference. A simulated low seam coal mine was constructed and subjects performed locomotion, shoveling, cart pushing, and timbering tasks with the 10/60 or self-rescuer attached to their belts. Task completion time was longer on all tasks when wearing the 10/60 unit, although only locomotion was statistically significant. The 10/60 unit was bumped over 100% more often than the standard self-rescuer. Implications for design of the proposed 10/60 container are: 1) unit?s container must be extra durable to withstand the added abuse it is likely to receive by low coal miners; and 2) extra consideration must be given to preventing the device from slipping on the belt while working, especially in low coal.

Jan 1, 1980

By C. J. Newman

Before 1995, the smelting process at the Kennecott Utah Copper Corp. (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. When considering expansion, it was decided that the existing process would not lend itself to a program geared toward processing the total output of copper precipitate and copper concentrate from KUCC mining and concentrating operations. During 1989 and 1990, several smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1 Mt/a (1.1 million stpy) of copper concentrate, with the ability to expand to 1.2 Mt/a (1.3 million stpy). The smelter facility that used the Noranda technology was shut down in May 1995. The flash smelting furnace operation began in June with the flash converting furnace start-up a few weeks later.

Jan 1, 1999

By W. H. Goghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

By Heithecker R. E.

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce,, published a report of the gas reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, may be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

By R. E. Heithecker

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce, published a report of the gas at reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, nay be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937