Search Documents

From 2009 to 2012, Aker Wirth, in cooperation with the BGR (German Federal Institute for Geosciences and Natural Resources), developed a concept for the deep sea mining of manganese nodules, which it also examined by means of a profitability analysis. The study was undertaken for the German Federal Ministry of Economics and Technology. The increasing scarcity of resources, coupled with the continuous rise in resource prices, drive the search for new raw material deposits. As a result, the deep sea is coming increasingly under the spotlight. At depths of more than 1,000 m (3,280 ft), large deposits of ores and precious and high-tech metals, such as manganese, cobalt, nickel, copper and gold, along with rare earths (which are important for the high-tech industry), can be found. The extreme deep sea conditions ? enormous water pressure, ice-cold temperatures and complete darkness ? present huge financial and technical challenges to the mining industry when extracting these materials. Aker Wirth has recognized the potential of this important future market early on and advances the development of relevant products.

Jan 1, 2013

By Charles H. Moore

When lime and magnesia are used as fluxes in the smelting of titaniferous ores fluid, digestible slags low in iron oxide and high in titanium dioxide are produced. The mineral phases present in such slags are (Fe,Mg)O.2TiO2, CaTiO3, and minor amounts of silicate glass (or its devitrification products). The flux additions are added to the ore in relative amounts to crystallize a ratio of (Fe,Mg)O.2TiO2 to CaTiO2, of near the eutectic proportions of 60 pct (Fe,Mg)0.2TiO2 and 40 pct CaTiO3. FeO-Ti02 (ilmenite) remains present in the slag until the FeO content is reduced to approximately 8 pct. Op- timum slag composition is obtained by reducing the FeO content to between 2 and 6 pct. Continued reduction shifts he (Fe,Mg) 0.2Ti02 to oxygen deficient structures classified as MgTi30e and MgTi204. Further reduction yields titanium oxycarbides and freezes the melts.

Jan 1, 1949

By G. Stuart Littlejohn

In spite of recent concerns in certain European countries, I believe that silicate-ester grouts will continue to be employed in practice, unless more cost-effective inorganic grouts are developed for the treatment of fine sands. It is also noteworthy that over the past 40 years, there has been a record of good experience where silicate-ester grouts have been used in ground improvement. Nevertheless, there is now a need via the European Standard EN 12715 (2000) "to assess the environmental impact, particularly the toxicity of the grout and grout components, and their effect on ground and drinking water should be considered before grouting." "When testing the grouting material for environmental impact, the following aspects should be considered: ? Whether during processing, transport or grouting, substance can be generated or released which could be hazardous to the environment or the grouting crew; ? Whether noxious substances can spread upon mixing with ground water; ? Whether reaction products can be produced or released which influence the water quality; ? The type of particles eroded from hardened grout; ? Chemical reactions between hardened grout and the ground water."

Feb 10, 2003

By C Hall, P Hazell, C Wilson

Every mine is situated within a water catchment – a catchment with potentially many other land uses. A mine may take up a relatively small area in that catchment, but its operations have the potential to affect the whole catchment and long after that mine has ceased to operate. Therefore, the residents of any given catchment have the right to feel secure in the knowledge that their catchment, and indeed the wider environment, will not be degraded by mining activities. Much conflict can arise when this confidence does not exist.But, imagine if a community not only felt confident that their catchment would not be degraded by mining activities, but was also confident that their catchment would be left in a better and continuously improving condition – with improving water quality, biodiversity and soil - and a strengthening, more resilient economy. CITATION:Hazell, P, Wilson, C and Hall, C, 2018. Landscape regeneration lessons learned from Mulloon Creek, in Proceedings Life-of-Mine 2018, pp 125–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By BERNARD PLANNER

PRODUCTION COSTS, profits, and quality are the primary factors in the peacetime production of iron and steel. In a war emergency, as high production rates and as complete utilization of readily available raw materials as possible, consistent with securing passable quality, become the most important factors. In this connection a discussion of some of the recent developments in the German iron and steel industry, where the problem of scarcity has naturally always been more acute than in the U.S.A., maybe of interest. To get more pig iron out of the existing blast furnaces it was necessary to obtain the maximum efficiency from the iron-bearing raw materials. This was achieved by eliminating all "excess baggage," chiefly by beneficiating the ore. The preparatory work for this was done by various methods which are effective when the ore either is too poor or contains too many impurities or too much gangue. Some of the beneficiation methods are well known, some are combinations of wet-mechanical, magnetic, roasting, sintering, and other treatments.

Jan 1, 1942

By N F. Glenn, S Thiruchittampalam, B P. Banerjee, S Raval

The determination of shear strength parameters for the spoil material plays a crucial role in the assessment of a dump’s stability; nevertheless, their evaluation necessitates laborious laboratory experiments. In order to address this issue, Simmons and McManus (2004) formulated a framework that serves as a foundation for categorising spoils according to their distinctive shear strength parameters based on observable and tactile characteristics. This framework, previously identified as the ‘BHP Mitsubishi Alliance Coal (BMAC) Spoil Shear Strength Framework’, is now recognised as the ‘CoalSpoil’ framework. The spoil characterisation provided by the CoalSpoil framework offers benefits but is not without limitations. The examination of these attributes in the field is a time-consuming task that demands expertise. Subjectivity arises in the spoil characterisation when attributes straddle the line between two categories, such as delineating matrix-supported and framework-supported fabric structures. To enhance consistency in the spoil characterisation process, minimising human intervention is crucial to mitigate bias, classification errors, and safety risks. This study seeks to achieve this aim by introducing image-assisted and automated methods for spoil characterisation.

Sep 1, 2024

By Irven A. Jacobson

This literature survey consists of references dealing with gaseous state thermal decomposition reactions of organic nitrogen and sulfur compounds. The reference source for the survey was the Chemical Abstracts from 1930 to 1956, inclusive. Original articles were not studied. The starting date was set at 1930 because previous to this time much of the work is questionable. This report is in three parts: Part I lists nitrogen compounds; Part II, sulfur compounds; and Part III, compounds containing both nitrogen and sulfur. The organization of the classes of compounds is alphabetical: Part I - amides, amines, amino acids, ammonia, azides, azines, azo compounds, heterocyclic nltrogen compounds, hydrazine, nitrates, nitriles, nitrites, nitro compounds and miscellaneous nitrogen compounds; Part II - disulfides, sulfides (including double and triple sulfides), thiols, thiophenes and xanthates; Part III - thioacid amides, thiazoles, thiocyanates and thiuram disulfides. A class formula is included with each class name. The R's used in these class formulas may refer to hydrogen or to the same or different radicals when more than one R appears.

Jan 1, 1960

By Paul C. Rusanowski

Mining is a waste intensive industry, oftentimes producing hundreds of kilograms of waste rock and tailings for every gram of metal recovered. Disposal of mine tailings is a major concern in most mining operations. In Southeast Alaska the steep terrain and high seismic hazard province limits cost effective opportunities for land disposal of tailings. The lack of infrastructure and long travel distances generally limits secondary utilization of tailings, as well. Since the mines are located close to tidewater, submarine tailings disposal is an attractive option for tailings management. At the present time the EPA will not issue a permit that authorized marine tailings disposal from any mining process that includes flotation technology. Upland disposal is the "Best available technology" and must be used. Consideration of submarine disposal is generally precluded because the tailings are contaminated with fluids from the flotation process. However, when developing technological solutions to minimize environmental disturbance, destruction, pollution, and risk, submarine tailings disposal deserves another evaluation. In Southeast Alaska it may be the "Best available technology" based on an assessment of all issues and concerns in these mining projects.

Jan 1, 1991

By SAM A. LEWISOHN

IT is popular today to dramatize in a journalistic spirit, some particular factor among the causes of unemployment. Naturally the time chosen for such emphasis is usually when the factor in question is temporarily a particularly active one. A few months ago, in the unemployment then current, we saw largely the results of a healthy acceleration in changes in processes, greater efficiency, a more intensified use of labor-saving devices, perhaps also a change in products. So we have been hearing a great deal about the influence of mechanization on unemployment, the so-called technological unemployment. Many talk as if this kind of unemployment were a wholly new phenomenon, for- getting that it is a constant process in a growing industrialism, though it sometimes becomes more pronounced. At other times one would think that seasonal unemployment is the only type of unemployment, and then again the fashion changes and we hear .about nothing except cyclical unemployment. Every few years there seems to be a different fashion in labelling the germ supposed to be the cause of unemployment.

Jan 1, 1929

By AIME AIME

WHEN the War Production Board issued its order which will end the use of iron and steel in more than 400 familiar civilian articles, the list of those products formed a fascinating and homeric catalogue of the things we use. Articles for which iron and steel may not be used after a 90-day "tapering-off" period are as workaday as office machinery and as frivolous as cocktail shakers. Mostly they are smaller items-the smallest probably are phonograph needles but in the aggregate they will save tremendous quantities of the metal most needed to win the war. In total war there are no trifles. Interesting proof of this lies in the fact that by eliminating manufacture of blackhead squeezers we shall save 110,000 lb. of steel a year. Out of this steel we might have made four 155-mm. field pieces. We might have made a thousand 3-in. trench mortars, 4400 0.30-caliber machine guns, 55 16-in. shells, 110 200-lb. aerial bombs, or three 15-ton tanks with something left over to arm them.

Jan 1, 1942

By M. O. Renwick, Paul Zinner

"INTRODUCTION In September 1943, the Bureau of Mines conducted a limited program of churn drilling on the Winskell property in the Shullsburg area of Lafayette County, Wis. The work was undertaken as part of a general investigation by the Bureau of the zinc-producing area of southwestern Wisconsin at a time when special effort war being made to increase the production of metals necessary for the war program.Drilling described supplemented a previous drilling program conducted by the Vinegar Hill Zinc Co. The results of both programs encouraged subsequent investigation by the Cuba Mining Co. and eventual development of the Andrews mine.ACKNOWLEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by such project as soon as praticable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the investigative work, and prepares the final report."

Aug 1, 1947

By Ankit Jha, Javad Sattarvand, Aaron Young

Blockchain technology is one of the prominent disruptive technologies that are being implemented in several disciplines. The application of blockchains in the mining and mineral industry can provide utility to several processes especially when the industry is undertaking digital transformation. The governing principles of blockchain technology are applicable in undertaking transformation in several processes within the mining industry. This study investigates the applications of blockchain technology within the realms of the mining industry and identifies key areas of implementation. A systematic review of publications on academic platforms relating to blockchain technology in the mining industry did not retrieve a considerable number of articles. Consequently, a thorough review of white papers and articles authored by individuals on use cases within the mining industry is compiled and presented in this review article. This review article identifies all the potential areas within the mining industry where blockchains could provide value and improve processes through their implementation. The broad area of implementation of blockchains includes supply chain, traceability in spares parts, contract management, regulatory compliance and cybersecurity.

Mar 1, 2024

By N Barnett, M Dello-lacovo, J Oh, S Saydam, T Pelech

In-Situ Resource Utilisation and Off-Earth mining require the application of horizontal drilling. The stability of such openings is challenging when excavating in the lunar regolith. Excavations on the Moon will encounter unconventional operational conditions such as different material properties, low gravity, and a moonquake. Micro-tunnelling or drilling to support lunar exploration and development of infrastructure on the Moon requires stability analysis to ensure its desired performance. The discrete element method (DEM) modelling technique has been utilised to investigate the optimum opening sizes on the lunar soil. From the literature, the mechanical properties of the lunar regolith have been reviewed and used for numerical model development. The model has been calibrated by simulating numerical triaxial tests with the Mohr–Coulomb failure criterion. Then, detailed parametric studies have been performed to investigate the influence of confinement, opening dimensions and moonquakes on the stability of openings. The findings have led to the development of a simple stability chart of the relationship between unsupported opening sizes and lunar regolith properties at different depths.

Nov 29, 2022

By Frank T. Sisco

DURING the past year the iron and steel industry of the world as a whole operated on a satisfactory basis. No discoveries nor new processes of outstanding importance were announced either here or abroad, although rumors of such were persistent. In general, the efforts of operating and research men in the iron and steel industry seemed to be confined to improving quality and reducing cost, not a new aim, for the same efforts have been noted in nearly all of the annual reviews of the industry for at least fifty years. Most published papers on blast furnace or steel-making practice were of minor importance, at least when judged by the criterion of radical change in process or product. If the number of reports in the technical journals, or articles in the trade press, is used as a basis for comparison, continuous-mill sheet is still the most important single product of the industry; papers were published detailing the results of the investigation of various phases of the

Jan 1, 1938

By R. W. Thompkins

MINE operators are concerned with temperature conditions in their mines, particularly the effects of high temperatures on the l1ealth and efficiency of tl1eir employees. This paper is written to focus attention on the variables of heat transfer between rock and air. It illustrates the difficulties of predicting the manner, and the extent, of heat transfer from theoretical concepts, prior to actual operation of a mine airway. There are ~1any sources of heat in mines. The most important is that of the rock surrounding the airway. This heat, in turn, is a product of the age of the rock, faulting, proximity to recent igneous activity, oxidation of sulphides, hot ground waters, etc. The sources of heat may be constant for any one mine, but they are far from constant when dealing with various mining districts or e1•en with a number of mines in the same district. A second source of heat is that produced by machinery in operation. Practically all the waste

Jan 1, 1962

By Adriano Gonçalves dos Reis

In the development of the structural materials for the advanced applications, as in the aerospace industry, there is a constant strive to increase both strength and toughness. Maraging steels are iron-nickel alloys designed to combine both properties that are achieved through the age-hardening of low carbon martensite. This alloy have a metastable martensitic structure that can revert to austenite when heated in temperatures close to the aging temperature, and this effect can be enhanced with the temperature increasing and time of treatment. Therefore, the study of creep behavior in elevated temperatures has technological importance to the development of this material. In this work the creep behavior of a maraging 300 steel solution annealed is evaluated by carrying out creep tests at 650ºC and in a stress of 200, 300 and 500 MPa. Creep parameters, such as steady state creep rate (?????), final creep time (tf), and stress exponent from secondary creep (n) are determined, considering that they are important to evaluate the creep resistance of the material.

Aug 7, 2018

By W J. Riva

This paper reviews the coal mining operations of The Canmore Mines, Limited, at Canmore, Alberta, paying particular attention to the use of this coal by the metallurgical and chemical industries. The characteristics of the deposits are outlined, and the mining and processing methods used are discussed. Introduction M INING in the Cascade coal area of Alberta began form-ally in 1886 when the Canadian Anthracite Coal Company was granted its charter. Earlier operations had been confined to prospecting and family-type enterprises serving the market area within barging distance on the Bow river. From 1886 to 1964, seven mines were opened between Banff and Ribbon Creek; six of these have since been abandoned, leaving the B c 0 L. original tenant, under the name of The Canmore Mines, Limited, as the sole survivor. The town of Canmore, hub of the mining ventures, is located on the main line of the C.P.R. and on the Trans-Canada Highway, 67 rail miles west of Calgary and 57 4 miles east of Vancouver, as shown in Figure 1.

Jan 1, 1965

By Russell G. Hood

Rock bolting or anchoring are methods of stabilization which are not being fully utilized in California and probably in other parts of the world due to lack of understanding of the principles, or due to poor results in actual installation. The problem is greater in California because so much of the rock is either soft or badly fractured and broken. Almost any recognized type of rock bolt or anchor will perform successfully is hard, fresh rock, but the problems become many-fold when working in decomposed granites, shales, soft sandstones or other soft, highly-broken rock. There has been an enormous amount of research by manufacturers, consultants, private organizations, and governmental agencies on rock bolting. It would be impossible to discuss all the methods and philosophies of rock bolting in this paper. Therefore, with the indulgence of the experts, I will give only a very generalized coverage on rock bolting techniques. However, My main purpose is to point out some of the problems of rock bolting in soft rock.

Jan 1, 1967

By PEILIN LAN, LEONARD HILL, SIMON TIMBILLAH, BERNARD FOSU, CESAR SOSA-BLANCO

The use of sodium hydrosulfide (NaHS) in most of the operations in byproduct molybdenum flotation comes with safety concerns and, in some instances, a high reagent cost. Engineered solutions at the various operations where NaHS is used have immensely reduced the possibility of hydrogen sulfide (H2S) gas evolution. However, the threat of exposure remains, and this, coupled with the high dosages of NaHS consumed, supports the continued search for alternative depressants. This paper focuses on efforts to study the applicability of disodium carboxymethyl trithiocarbonate (DCMT), an organic depressant, as an alternative to NaHS. Bench-scale rougher flotation results for samples from the Sierrita copper–molybdenum (Cu–Mo) plant showed the best DCMT performance at 8 kg/t of DCMT, pH 10.5, 30 min of shear conditioning and 10 min of flotation conditioning. The Aminpro plant model simulation confirmed that 4 to 8 kg/t DCMT under certain shearing and conditioning times achieved superior or equivalent Mo–Cu separation efficiencies when compared\ to NaHS.

By S. Sener

In this investigation, the changes in the grindability of both ulexite and colemanite related with the different structural modifications created by the heat treatment were examined with respect to work index (Wi). The effects of the heat treatment temperature and time on grindability index were also investigated. It was observed that, heat treatment significantly affected on the grindability of ulexite. The work index of original ulexite was found 7.11 kWh/shton and decreased to 3.5 kWh/shton level within 200-480°C for 60 minutes. On the other hand, the work index of original colemanite was found as 6.48 kWh/shton and no appreciable change was observed when heated up to 320°C. Thermally assisted comminution can be used to improve the grindability characteristics of ulexite. Besides, the different behaviour of ulexite and colemanite under heat treatment can be used for their separation. The artificial mixture of ulexite and colemanite could be separated with over 90% recovery by utilizing their different grindability characteristics by thermal treatment, semi-autogeneous grinding and screening.

Jan 1, 1999