Search Documents

By Donald J. Drinkwater, M. C. Fuerstenau

Many important contributions to the more fundamental aspects of mineral processing have been made this past year. Mular1 researched the flotation characteristics of pure zinc oxide and also samples that had been doped with Al+++ and Cu++. Correlation of the response of pure zinc oxide to oleate flotation with a calculated zpc (from solution equilibrium) suggests that adsorption of oleate ion is coulombic in nature. Doping the sample with Al+++ (which will make the ZnO more n-type) had a marked effect on the maximum value of pH at which 50% recovery was obtained at constant collector addition. That is, when 0.5 mole percent Al+++ was added, the pH for 50% recovery was reduced by about four units. Treatment with Cu++ was found to have little effect on the flotation response of zinc oxide, even for additions of one mole percent. Since the zero points of charge of the Al+++ doped powders were not measured, it was not possible to correlate flotation data of these samples directly with charge phenomena.

Jan 2, 1966

By Gross A. E, Neville P. C

Over the last decade heap leaching with a cement binder has allowed the economical leaching of low grade gold ores of less than 2 grams/tonne. Despite the continued use of cement as an agglomeration aid, numerous leaching operations continue to experience channelling and blinding problems. This paper describes the development of polymeric agglomeration aids, Extract Ore 9760 and 9960, which when used as a partial cement or lime replacement can result in a higher rate of and/or a higher total gold recovery in plant evaluations. Extract Ore in combination with cement acts to produce a stronger agglomerate which results in reduced fines migration during leaching and helps prevent blinding of the heap. Both of these changes will give a more even flow of cyanide solution throughout the heap and improve solution contact efficiency within the ore. Polymeric agglomeration aid programs are now being used by heap leaching operations in three different countries. A summary of benefits identified at some of these operations are presented in this paper.

Jan 1, 1994

By Martin H. Stanczyk

Ultrafine grinding of the industrial minerals mica, pyrophyllite, talc, marble, barite, and fluorite was accomplished using the Bureau-developed and patented attrition-grinding process. The materials, representing minerals of diverse physical characteristics, were batch ground in a 10-inch-diameter machine using statistically designed experimental test programs. The tests were made to determine large effects of variables such as feed pulp density, grinding medium size, and quantity of the electrical energy consumed during grinding on product particle size and bulk density. In designing the test programs, it was assumed that there was no interaction between the variables. Relatively coarse commercial flotation concentrates of mica, barite, and fluorspar and mine-run products of pyrophyllite, talc, and marble were readily ground into subsieve size ranges. Considering the great amount of particle size reduction obtained, the electrical energy requirements for grinding were very low. In general, the test results indicated that the best conditions for particle size reduction were approached when grinding with the coarser fraction of sand grinding media, the higher-sand-to-mineral weight ratio, and the higher feed pulp density.

Jan 1, 1972

The longwall system with caving is the most common mining system in Polish Collieries and the extraction is carried out simultaneously on several levels and in different seams. The extent and diversity of the methane hazard occurring is strictly connected to the specific geological and gas conditions as well as to the applied mining methods. Taking these factors into consideration the following methane drainage methods are applied as additional means of combatting the methane hazard in Polish gassy coal mines: 1. predrainage by means of boreholes drilled from the surface, 2. predrainage from stone drivages and devel- opment workings, 3. degasification of coal extraction workings, and 4. degasification of sealed-off areas/old goaves. Predrainage gave satisfactory results when holes were drilled from the surface or from underground workings, but only to depths to 300 m. It was necessary to adapt methane drain- age methods to the geological and mining con- ditions as gassiness increased with depth. The results of methane capture, both pre- drainage and post drainage were obtained by investigating several gassy mines.

Jan 1, 1982

By Alfred H. Bell, Charles W. Carter

In 1943, Illinois produced 82,256,000 bbl. of oil, or 5.5 per cent of the total for the United States, and ranked sixth in the nation in oil production. This represents a decline of 23 per cent from 1942, when the total Illinois production was 106,ggo,o~~ bbl. and Illinois ranked fifth. The daily average production for 1943 was approximately 225,000 bbl. Daily averages by months were as follows: Jan......... 238,000 July......... 218,000 Feb......... 240,000 Aug......... 216,000 Mar......... 237,qoo Sept........ 220,ooo Apr......... 230,000 Oct......... 220,000 May....... 221,000 Nov......... 223,000 June......; . 222,000 Dec......... z18,ooo This shows that most of the decline during the year took place between March and May, and that for the last eight months of 1943 production has been essentially steady. This means that there has been enough production from new wells drilled to balance the natural decline of the Older wells. The trends of drilling and production are shown in Fig. I and Table 3.

Jan 1, 1944

By Thomas A. Gray, Lynn M. Crayne, Michael A. Trevits, Phil Glogowski

Mine seals can be remotely constructed in underground coal mines, through vertical boreholes, when direct access to a fire is impossible or considered to be too dangerous. This method has great merit because boreholes can be drilled to specific mine areas and seals can be positioned close to a fire zone. The technology however, can be largely ineffective if the constructed seals do not provide effective barriers to airflow or cannot be used to impound water and other inert materials. Unfortunately, no viable alternatives exist to sealing the entire mine at the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Lake Lynn Laboratory (LLL). Under this effort, Howard Concrete Pumping Company and GAI Consultants, Inc. have joined forces to evaluate a potentially significant improvement to the current state-of-the-art. This paper will cover development of novel technology for remote mine seal construction, evaluation of the materials used, construction practice, and follow-up testing.

By Donald R. Irving

ALTHOUGH the quantity of material handled at metal and nonmetal mines in the United States in 1962 was 2.7 billion tons, the same as in 1961, a larger proportion was waste. At metal mines, crude ore production declined 1 million tons and waste output rose more than 18 million tons; at nonmetal mines crude ore production declined 6 million tons and waste output rose 36 million tons. Copper and iron ore producers increased their share of crude ore and material handled from about three-fourths to four-fifths of the national metals total, and sand and gravel and stone producers in-creased their share of the nonmetals total, also from three-fourths to four-fifths. Six States-Arizona, California, Florida, Michigan, Minnesota, and Utah-each handled more than 100 million tons of ore and waste, and together they accounted for 43 percent of the U.S. total. When the large-volume construction materials (sand and gravel and stone) were excluded from the totals, four States-Arizona, Florida, Minnesota, and Utah-supplied over half of the material handled.

Jan 1, 1963

By D. E. Traut

A fluidized, countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future national needs. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous, except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid-leach-uranium solution and a strong-base, ion-exchange resin was studied, together with subsequent elution using an acidified sodium chloride solution. The effects of the number of compartments, compartment height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. Also examined were the kinetic and equilibrium relationships for the absorption and elution steps. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The columns system was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By D Craw

A glasshouse experiment was set up to investigate arsenic uptake in rye corn grown in different arsenic rich substrates. Sods of material were taken from various locations and planted with rye corn seeds. The plants grew for 13 weeks after which time the above ground biomass was harvested. Analysis of the rye corn plants showed a narrow range of arsenic concentrations, which did not reflect the arsenic contents of the soil. Comparison of the results from this study with previous work showed the glasshouse rye corn to have lower arsenic concentrations in above ground biomass than rye corn grown in field conditions. The environmental conditions present on the tailings and water-rock interactions were considered the main factors involved with the difference in arsenic uptake between field studies and the glasshouse study. This suggests that bioavailability processes are influenced by a variety of factors and cannot necessarily be predicted by the use of soil factors or glasshouse trials alone as is often done when planning phytoremediation work and mine shut down.

Jan 1, 2007

By R. Hoffmann

The Waelz process produces oxides of volatilizable metals from ores, metalliferous products and residues. The process was originally used for recovering zinc and lead, where tailings and residues containing those metals had accumulated at mines or smelters, but it is applicable for obtaining tin, arsenic or other volatilizable metals. It is useful when other methods of obtaining the metals from the ores or residues are too difficult or expensive or show too low a recovery. The Waelz process was developed in 1923 for the treatment of large calamine dumps in Upper Silesia, which showed zinc contents of 8 to 10 per cent. and lead contents up to 3 per cent. The rapid development of the process, from the first trials up to the plants now working or in course of erection, is shown in Fig. 1. The first industrial Waelz plant was started in 1925. Within two years the capacity of the working plants reached 700 tons material per day of 24 hr. During the year 1928 the daily capacity of the plants now at work or in course of erection will rise

Jan 1, 1928

Traditionally, the predominant drilling method in open pit mining has been large hole rotary drilling using cumbersome, inflexible equipment offering merely limited scope for improvements in pit design and overall costs. By contrast, the recent development of comparatively light high-pressure down-the-hole hammer crawlers has paved the way for new ideas and trends. High penetration rates coupled with superior mobility and fast set-ups contributing to substantial productivity gains have resulted in a renascence for this drilling method in open pits. The ability to cover a wide range of hole diameters and angles gives designers unique drill pattern possibilities especially when establishing steep and stable pit slopes. As pre-split holes, buffer holes and production holes all can be drilled by using the same equipment, there are, there are obvious advantages in production scheduling as well as in materials handling and service. This paper presents some case stories, which will demonstrate the benefits and improvements that the introduction of new drilling methods and equipment has brought to open pit mining operations.

Jan 1, 2003

By Delbert E. Gann, Richard D. Hagni

Ore microscopic study of copper-bearing shale at the Creta mine in southwestern Oklahoma reveals a variety of copper sulfide grains and shows that each has originated by replacement of original constituents In the Permian Flowerpot Shale at Creta. The largest grains, about 120 pm in diameter, are replacements of megaspores with triletes morphology. Their interiors are shown by Auger microprobe analyses to be organic matter. The interior organic matter and the spore exines have been replaced by anilite and djurleite. Digenite and anilite replace collomorphic pyrite averaging 40 pm in diameter. Grains 10 pm or less in d~ameter are mostly euhedral, six-sided, platy crystals that have anllite compositions and are pseudomorphous after pyrrhotzte. Other 10 pm copper sulfide grains are pseudomorphous after octahedra and cubes of pyrite. The results of this study indicate that the copper minerals are epigenetic and were deposited from fluids introduced into the Creta shale when it was relatively uncompacted and permeable. The shale served as a favorable reducing environment that contained a source of sulfur in the form of pyrite and pyrrhotite.

Jan 1, 1985

By Stephen Tadolini

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high¬loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

Jan 1, 2003

By Galen G. Waddell

Several years of rock-burst research conducted by the U.S. Bureau of Mines in cooperation with the mining companies of the Coeur d'Alene mining district, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem. A rock burst is the sudden, violent release of stored strain energy in rock by some mechanism of rock failure, generally accompanied by expulsion of rock with consequent damage to the mine. A burst may be audible for only a few hundred feet, or on the surface it may sound like a sonic boom miles away. A Dictionary of Mining, Mineral, and Related Terms, U.S. Bureau of Mines (USBM)* 1968yand defines a burst as Bureau "That phenomenon which occurs when a volume of rock is strained beyond the elastic limit and the accompanying failure is of such a nature that accumulated energy

Jan 1, 1971

By F. Twyman

PART I.-QUALITATIVE, SPECTRUM ANALYSIS THOSE chemists (they are still greatly in the minority) who use the spectroscope, use it very often, and find it almost indispensable. As a means of detecting minute quantities of the metals it is unrivalled. A metal can be readily distinguished in the presence of any other element, compound, or mixture without the necessity of separation. The qualitative analysis of the metallic constituents of a substance, which, the spectroscope gives so easily, is a sure basis for planning a chemical analysis. As the determination of each element proceeds the purity of precipitates maybe checked as often as desired. If, possessing these advantages; the spectroscope has been neglected in general chemistry, it is not surprising that it was neglected in metallurgical chemistry; for many of the impurities which are of industrial interest, even when they are present in a metal or alloy in small quantities, are not then always easily detected by the examination of their visible spectrum. The history of the development of the art has been given in Bureau of Standards Scientific Paper No. 444.

Jan 1, 1928

By Kazem Oraee-Mirzamani

Blasting operations generate seismic effects in underground mines. These effects apply additional dynamic loads on the support system, which should bear both static and dynamic loads. Static loads are caused by the weight of the superincumbent strata, while dynamic loads occur as a result of blasting in the mining area. Identification of the origin and determination of the support system behavior in natural frequencies is crucial in assessing the stability of underground mines. This is because resonance occurs when a support is vibrated with its natural frequencies, which can cause a vibration with the maximum amplitude and subsequently cause extreme deformations. The mechanism of support system deformation during dynamic load displacement has been studied and numerical simulation for the impact of the dynamic loads on stability of supports is carried out using finite element method. The paper introduces a simple technique for improving stability and safety of mining operations. Results obtained and the methodology adopted in this research can help mining design engineers make decisions on adequate support for active mining operations.

Jan 1, 2011

By Clarici E, Marsden J. R, Calderbank P. A

Evaluation of previous studies of multi-layer perceptron type artificial neural networks in the modelling of the deformability behaviour of rock have suggested that a deviation from the standard method of laboratory testing of rock under triaxial loading at constant confining stresses and constant axial strain rates may be inappropriate when the data produced are used to train an artificial neural network. In this paper, preliminary results of adopting such a strategy are reported. Of specific concern is the establishment of a suitable schedule for the stress path during testing. Furthermore, the training element of back propagation optimisation was directed towards prediction of new stresses given old stresses and old strain increments. Adoption of this method of supervisation in artificial neural network training facilitates the integration of the trained neural network within existing numerical methods used in rock mechanics. The target code was a finite difference Lagrangian formulation for the analysis of continua. Sandstone rock taken from a quarry in the UK was used in the study which showed that the method has great potential.

Jan 1, 1995

By A. J. Harrison

"The introduction of an amendment to the Mines Regulation Act in the Province of British Columbia, passed in July 1974, and similar amendments since enacted by other provinces introduced the Canadian underground mining industry to the use of fire-resistant hydraulic fluids.Few, if any, of the hydraulic circuits in use in underground mining at that time were specifically designed for use with fire-resistant fluids, compared with the increasing number of such circuits conceived and in production today. The technology required in designing equipment for use with fire-resistant fluids may be likened to that associated with conventional mineral oils, but, in many respects, a variety of additional and / or alternative considerations must be taken into account. The fast-increasing use and development of fire-resistant fluids throughout all facets of industry, world wide, during the past 20 years has led to a whole new technology in system construction and component design, whereby acceptable performance can be achieved . However , the transition from conventional mineral hydraulic oils has not been without its problems, particularly when retro-fit of existing units was involved."

Jan 1, 1981

By Philip D. Pearson

CALAND Ore Co.'s dredging program has reached the halfway mark. The goal is to remove more than 160 million cu yd of lake bottom material overlying the iron orebody in Falls Bay of Steep Rock Lake, Ont. Two large dredges were constructed to remove this overburden, a layer of soil about 90 pct varved clay some 400 ft thick. Moisture content of the clay is high-approximately at the liquid limit of the soil. A few years ago, searching for additional reserves of ore, Inland Steel Co. looked toward Canada and the newly developed Steep Rock iron range. To this end an option agreement was signed Dec. 30, 1949, between Steep Rock Mines Ltd. and Caland Ore Co. Ltd., a wholly owned subsidiary of Inland Steel. Several drilling programs were conducted between this date and Jan. 1, 1953, when a 99-year lease was signed covering an area of 1249 acres. This lease calls for ore production to begin in 1960, with full production of 3 million tons per year by 1969.

Jan 8, 1957

By G. H. Shefelbine

DISCOVERED during the time of the Spaniards, the Namiquipa silver-lead-zinc mines in Chihuahua, Mexico, remained idle until 1916, when mining claims were first denounced. About 1922 a Japanese company, the Santo Domingo Mining Co., was formed to mine the oxide silver ore. The company built a 75-tpd cyanide plant and mined in the area for a number of years. Because of an error in surveying in one of the company's mines situated in another district, mining was carried over into a claim owned by General Marcel Caraveo, at that time governor of Chihuahua. Santo Domingo Mining Co. lost the resulting lawsuit and consequently had no capital to continue operating at Namiquipa. Later, Ray Brown and Eugenio Caballero formed a company to operate the mine, shipping crude ore to the American Smelting and Refining Co. smelter at Avalos, Chihuahua. The cyanide plant was changed to flotation with a capacity of 75 tons per 24 hr. In 1936 the property was again closed owing to labor trouble, a drop in the price of silver, and increased water in the mine.

Jan 10, 1957