Search Documents

By Ira Sohn

This article revisits global projections made in 1981of eight metallic and fertilizer minerals for the year 2000. The objectives here are to quantify the differences between the projected and observed levels of consumption for the year 2000 for eight of the 26 nonfuel minerals covered in the earlier study. An attempt is then made to attribute these (often) large differences to the major determinants of minerals demand — income, technological, regulatory and other policy changes, and changes in the recycling rates of the metallic minerals. The eight minerals covered are aluminum, copper, iron, mercury, nickel, phosphate rock, potash and tin. This summary article presents the actual population, gross domestic product (GDP) and per capita GDP changes from 1970 to 2000, compared with the projected rates for these important determinants of mineral use, along with the observed growth rates of minerals consumption for the eight nonfuel minerals included in this study. When the projections are compared with the observed global consumption levels for the year 2000, the differences range from +43 percent for nickel to +229 percent for potash.

Jan 1, 2005

By Robert B. Parsons

"Finance Minister Paul Martin's second budget might be good for Canada's mining industry in the long run, but the budget raises a number of concerns for the industry in the near term. The budget papers suggest that the 25% resource allowance is not working as intended, and report that the Department of Finance will be reviewing this valuable allowance. The so-called ""large corporations tax"" rate will be increased. This annual tax, which is imposed on a corporation's capital even when the corporation is not in production, is particularly harmful to the mining sector.IntroductionThe Honourable Paul Martin, in his second federal budget, emphasized spending cuts and made only modest tax changes. However, two of these tax changes could have a serious impact on the Canadian mining industry: the proposed review of the 25% resource allowance; and, the increase in the large corporations tax rate.Personal Tax Measures Personal Tax Rates UnchangedThe government has been under political pressure not to increase personal tax rates. Mr. Martin's announcement that rates would not change will be popular."

Jan 1, 1995

By A. D. Pelton

The evolution of thermodynamic models of molten salts and slags, starting with Temkin in 1948, has culminated in today?s sublattice models. These modern models have permitted the development of large thermodynamic databases of model parameters, which can be used to calculate and predict accurately the properties of multicomponent solutions. The model parameters are mainly obtained by the critical evaluation and optimization of available thermodynamic and phase equilibrium data for binary and ternary subsystems. The models are then used to estimate the properties of multi component slags and salts from these assessed binary and ternary parameters. When used in conjunction with thermodynamic databases for solids and solid solutions (salts, oxides, sulphides, metals, etc.), other liquid solutions (such as liquid metals),and gases, these databases permit the calculation of complex multiphase equilibria in multicomponent systems, with applications in a wide variety of industries. These calculations can be performed with general commercial software for Gibbs energy minimization, which can also be incorporated into process simulation software packages. Keywords: slags, salts, solution models, thermodynamics, phase diagrams, oxide systems, molten salts

Jan 1, 2004

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By L. F. Albert

The paper describes solutions given to foundation problems during the reconstruction of a power plant set on fire, located adjacent to several still Working Units. After a detailed site and laboratory investigation, it was decided that it could be possible to include within the new foundations the preexisting cast in situ driven piles with enlarged base 50 cm in diameter and let them work with new 41 cm driven, cast in situ piles without enlarged base. Demolition of existing caps was carried out with expansive mortar in order to avoid any possible damage to piles, whose actual conditions were checked by several load tests. New piles were designed to support service load by shaft resistance, in order to limit total and differential settlement. When piles had to be driven adjacent to nearby structures, measurements of peak soil particles velocity were carried out while driving piles at decreasing distance from critical locations. By preboring most of the upper clay layer it was possible to reduce within safe limits for structures the induced vibrations.

Jan 1, 1989

By R. Grimard, M. Gamache, L. -P. Bigras, P. Cohen

This paper describes a real-time fleet management system for an undergroun mine. Dispatching, routing and scheduling are handled simultaneously, taking into account the mine status, operational constraints and vehicle location information. Each assignment decision takes into account the traffic on the road segments of the mine network, whether road segments are bi-directional or uni-directional, and ensures that each LHD (load-haul-dump) vehicle arrives at loading and dumping points with the correct orientation. Such a system can be used either as a simulation tool for strategic planning or as a real-time managing and optimizing system for operations. In the simulation mode, the system can accurately estimate the impact on productivity of decisions such as the development of waiting areas (bays, sidings), or the addition (elimination) of vehicles to the fleet in operation. When used for real-time dispatching, routing and scheduling of vehicles, the system can optimize production with respect to various assignment criteria such as cycle-time minimization or deviation from a target production plan.

Jan 1, 2004

The processes by which particles and bubbles interact capture many of the central concepts of colloid science and hydrodynamics. This area of research embraces hydrodynamics, interfacial(including capillary) forces, particle and bubble behaviour and solution chemistry. In this review, we discuss collision, attachment and stability efficiencies. We deal with the identification of a flotation ?domain?, the deformation of a bubble surface upon interaction with a solid surface, the kinetics of three phase contact line expansion and the determination of attachment efficiencies through to the direct measurement of bubble-particle interaction forces. We have recently carried out a test of collision theory where the latter embraces both inertial and centrifugal forces. The real challenge is now to quantitatively describe the behaviour of real systems and to incorporate a reliable description of the behaviour of particles in flotation froths. The approach described is very robust when applied to flotation, both from qualitative and quantitative points of view, providing an intellectual foundation for understanding this complex process in separation science and technology.

Jan 1, 1999

By W. H. Dickinson

The performance of seven antiscalants spanning a range of chemistries was evaluated for control of calcium carbonate (CaCO3) formation in gold processing applications. Three preferred chemistries were identified which provided up to 100 percent inhibition in static jar tests when applied at 30 ppm dosage. The three products were further evaluated using a model carbon extraction circuit developed for this application. The test circuit enabled direct measurement of calcium carbonate formed on the carbon from a supersaturated solution under dynamic conditions. The antiscalants lowered CaCO3 buildup on the columns by 15 - 26 percent compared to untreated controls. Impact of the antiscalants on the rate and extent of gold loading onto a carbon adsorbent was evaluated in laboratory carbon-in-pulp (CIP) studies. The antiscalants generated a 25 - 35% increase in gold loading at gold extraction efficiencies up to 65%. On-site testing at a gold processing facility demonstrated that 10 ppm of the preferred antiscalant was able to fully suppressCaCO3formation in thickener overflow water.

Feb 27, 2013

By F. Hassani, R. Mikaeil, B. Ferdowsi

Two analytical solutions for estimating the ovaling deformation and forces in circular tunnels are widely used in engineering practice, due to soil-structure interaction under seismic loading. This paper discusses the discrepancy between the two analytical and finite difference methods. A comparison of the two analytical methods shows that the calculated forces and displacements are identical for the condition of full-slip between the tunnel lining and ground. However, the calculated lining thrusts differ by an order of magnitude when considering no-slip between the tunnel lining and the ground. The analytical solutions are compared to numerical analyses of the no-slip condition using the finite difference method to validate which of the two methods provide the correct method. To achieve the goal, numerical modelling, field data of the Kuhin railway tunnel and Manjil earthquake characteristics are used. Numerical analysis results agree with one of the analytical solutions that provides a higher estimate of the thrust on the tunnel lining, thus highlighting the limitation of the other analytical solution.

Jan 1, 2008

By K. E. Merklin, F. D. DeVaney

Students of the modern blast furnace seem unanimously agreed that they are observing a major revolution in practice. Rather than changing construction and operation of the furnaces, most of the great advances now under way deal with the raw materials feed. Prepared burdens have gained increasing significance during recent years. Sizing, concentration, and agglomeration have all become bywords to greater production and reduced operating costs. The remarkable results with test furnaces in which self-fluxing sinter makes up part or all of the ore charge foretell even greater improvements. Other investigators have reported many of these advances, and it is enough to predict here that more and more operators will turn to the use of self-fluxing sinter. This change in the operator's requirements comes at a time when one major section of the iron ore regions, the Mesabi, is finding it difficult to maintain, let alone improve, the tonnage and grade of its shipping product. To meet the new demands with respect to quality and structure, the iron ore producers of this area turned first to screening, crushing, and concentrating intermediate ores. More recently, declining higher-grade reserves have led to multimillion-dollar investments in plants to treat the low-grade magnetic taconites.1,2 To yield a suitable concentrate, the Minnesota magnetic taconites must be ground to about 80 pct through 325 mesh, too fine to be charged directly to the blast furnace or to make acceptable feed to the sinter strand. The pelletizing process was developed to meet the structure requirements laid down by the blast furnace operators. Taconite producers are succeeding in their efforts just when the attention of the blast furnace man is being drawn to the great advantages of self-fluxing sinter.3 The taconite operators are ready with an alternative. Why not produce sclf-flus ing pellets? At the Hibbing laboratory of Pickands Mather & Co., where much of the early work was done that led to Erie Mining's 7.5-million ton taconite plant at Hoyt Lakes, Minn., preliminary investigations have been made. Present Taconite Operations: Details of this work will be clarified by a brief review of agglomeration practice in commercial taconite plants. After the taconite has been ground to about 80 pct through 325 mesh to liberate the magnetite grains, the ore is concentrated on magnetic separators, thickened, and filtered to about 10 pct moisture. This structure and moisture fit in closely with the conditions required to produce good balls. It has been found with taconite concentrates that at least 60 pct of the feed to the balling drum must be —325 mesh to obtain good ball compaction within reasonable time. The filter cake moisture usually permits a slight water addition at the balling drum, and further balling control is obtained by adding about 12 Ib of bentonite and 1 1/2 lb of soda ash per dry short ton of concentrate. These additives, and occasionally small quantities of fine coal, are thoroughly mixed with the filter cake ahead of balling. The swelling property of bentonite improves the green and dry strength of the balls so they can be handled without breakage until they are fired. Soda ash is added for pH control to insure maximum performance of the bentonite, and coal is added for more heat in the firing process when required. The balls, normally 3/8 to l-in. diam, are brought to a temperature of 2350" to 2500°F in the indurating furnace. Heat for this process comes from three sources: 1) fuel burned in the combustion chamber, 2) oxidation of the magnetite concentrates to hematite, and 3) coal added to the balls. Pellet strength is developed by grain growth and bridging and, if enough slag-forming constituents are present, by slag bonding. Conversion to hematite is usually close to 100 pct in the fired pellets. Batch Test Procedures: Initial studies of self-fluxing pellets were made by producing balls on a batch basis under carefully controlled laboratory conditions. The l-in. balls, uniform in size, were fired in an oxidizing atmosphere in a standard laboratory muffle furnace. The firing procedure consisted of

Jan 1, 1961

By M. V. Mielke, R. E. Hagen, R. L. Bennett

FINE IRON ORES, and concentrates such as those produced from taconite, must be converted to lump form by some process of agglomeration before they can be used effectively in the blast furnace or open hearth. At the present time, four major processes for agglomerating these materials are being used on a commercial scale: sintering, nodulizing, pelletizing and briquetting. IN 1945 U. S. Steel Corp. through its subsidiary the Oliver Iron Mining Div., drew up tentative plans for an agglomerating plant on the Mesabi Range which would include a nodulizing kiln and a sintering machine. The purpose of the plant was two- fold: during its initial operation it would provide data on agglomeration of high grade ore fines, and would help relieve the shortage of ore for open hearth charging. Subsequently, it would be available for agglomerating taconite concentrates. While operating on fines screened from direct ore, it was planned to develop techniques and personnel so that a workable plant would be ready to handle taconite concentrates when the time came.

Jan 1, 1954

When the Mining Bill came before the Victorian Legislature not so many months ago, the question arose whether mining managers required education, and to what extent. Some members of the House expressed themselves in a way which appeared to leave the impression that mining managers would be all the better if they were not brought up in a scientific school.To try and prove what we owe to science I will give a short history of colonial mining from the earlier period to the present time and compare results.I believe I am right in saying that South Australia is the pioneer colony in mining and to her belongs the credit of not dnly being the first mining colony, but also that her beginning turned out so successful, as the history of the Burra Burra copper mine will testify. At about the same time a little galena mining was carried on nearer to Adelaide, but as this did not prove a success and was only worked by tributing parties, little notice was taken of it.

By James A. Madonna

Information gathered while studying geological parameters that govern fine gold deposition in the a1luvial environment can be applied to the technological development and selection of fine gold recovery systems. It is recognized that substantial gold losses occur in the minus 1.5 mn (minus 12 mesh) fraction using conventional sluicing systems. Within the past two decades much attention has been given the design and efficiency of these thick bed concentrators. Studies and comparisons drew information from several foreign and domestic placer operations. These studies concentrated on: 1) the physical and chemical properties of alluvial gold 2) the parameters that control fine gold deposition 3) the geometrical form, components and general working structure of conventional sluicing systems 4) the physical properties which contribute to the overall efficiency of a sluice system 5) the comparison of three major styles of conventional sluicing systems. A dramatic improvement regarding fine gold recovery and water quality was observed when using modern multiple-channel sluicing systems in place of conventional single-channel sluicing systems.

Jan 1, 1988

By J. A. McLennan

Geological uncertainty is an unavoidable characteristic of all mining projects since only limited information is available from sampling. Mine planning and development decisions with significant economic consequences are made when the geological heterogeneity is inherently uncertain. Geostatistical simulation is preferred over kriging because the methodology provides alternative property realizations that can be combined into a model of geological uncertainty. Geological uncertainty can be transferred into production uncertainty, which can help characterize the economic risk of the project. This paper presents a case study for the Pogo property, being prepared for development near Fairbanks, Alaska. The exact dimensions, grades and production predictions have been modified; however, the methodology is illustrative. The geostatistical methodology consists of (1) assembling the relevant drillhole data and establishing a suitable coordinate system, (2) calculating the target distribution, (3) creating a model of spatial correlation, (4) generating multiple realizations at a small scale and (5) linearly averaging all the realizations to the chosen selective mining unit (SMU) support size. The geostatistical model is then used to calculate production uncertainty.

May 1, 2004

By G. S. Takenaka

When Bridger Coal Company transformed their operations from surface mining to an underground longwall operation their plans included not only the addition of new mining equipment but also surface fans for a blowing (supply) air ventilation system. The original system concept included a propane gas fired air heater to preheat the intake air during cold weather and a dual parallel fan and duct system. One fan operated to ventilate the mine while the other fan was for stand-by emergency operation. Equipment proposals were submitted in March, 2005 based on the dual parallel fan system. Discussions conducted during the equipment selection process revealed that several alternative system design concepts were available. The alternative concepts included innovation features that not only saved space and cost but also reduced operating expense as well. Many of the features were incorporated into the final design of the system. A comparison of the original system concept and final installation design are presented in the paper in addition to details of the features and the derived benefits.

Jan 1, 2009

By Ram Avtar

High tensile thick plates (>80mm, weight ~3000 Kg) of medium carbon low alloy steel, when heat treated, manifested higher percentage of crystalline area (>20%) in fractured surface. Such problem was not encountered in thinner plates. The genesis of higher crystallinity in fracture was examined. It was observed that the thicker plate undergone slower rate (Average 0.9oC/Sec.) from soaking temperature to Ms temperature) of cooling after austenising during oil quenching and thereby quenched microstructure had upper bainites. During tempering of as quenched bainite, additional precipitation took place at the lath boundaries of bainite. This led to weakening of grain boundaries and aided easy crack propagation during fracture and resulted in formation of higher percentage of crystalline area in fractured surface. Enhancement in cooling rate (Average 1.8oC/Sec. from soaking temperature to Ms temperature) of austenised plate by switching over from oil quenching to water quenching practice resulted in complete transformation of austenite into martensite and produced ductile fracture (zero Crystallinity). Plates conformed improvement in mechanical properties between 2-5%.

Jan 1, 2009

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012

In the extraction of level bridge pillars in the South Mine by square-setting methods the general practice is to work transversely from the hanging wall in narrow sections three or four sets wide to the depth of the bridge-usually three sets. When the working block attains an area of twelve square sets, sand filling is run in, either by pneumatic (Proceedings No. 123, 1941) or hydraulic methods, in order to control the settlement of the general area and prevent the development of undue weight in the stope. Upon completion of the filling operations, or coincident with them, ore breaking is resumed and the transverse section of the bridge pillar gradually reduced. A number of these parallel sections may be working at the same time.In preparing a block of sets for filling a great deal of paddocking is required, both to contain the filling and to preserve access to ladderways and ore chutes which may be situated at some horizontal distance. Stope paddocking until recently was constructed of 10 in. x 2 in. boards nailed...

Jan 1, 1942

The smelting of the Broken Hill lead concentrates at the Broken Hill Asso,ciated Smelters produced, among other products, approximately 4,900 ounces of gold and 8,800,000 ounces of silver during the year ending June 30th, 1938. The following table shows the actual amounts of gold per ton of lead concentrate produced during this period at the important mines. The total gold in the period is calculated from the number of tons of lead concentrates produced, and by comparison with the production' of silver, shows thatthere is no constant relation between the amounts of gold and silver.The fact that no gold is seen during milling, even when gravity concentrating tables are employed, signifies that the gold does not occur as occasional coarse particles.Further, as the values increase considerably in the flotation slime, it can be inferred that the gold occurs as minute inclusions in one or more of the minerals in the lead concentrates.The four most abundant minerals in the lead concentrate are galena, zinc blende, chalcopyrite, and...

Jan 1, 1940

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012