Search Documents

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016

By Ravi Ray, Kostas Kaklis, Zach Agioutantis

"Modern underground mining is becoming more complex and geotechnically challenging. The engineer uses numerical, analytical, and data-driven methods (empirical and/or experimental) or their combination to overcome these challenges. Each method has its advantages and disadvantages. Nevertheless, given the amount of innovation and experience involved in developing each of these techniques, it will be prudent to use all their benefits rather than favoring one technique over the other. Pillars are the most important support element in an underground mine. A holistic geo-mechanical solution needs to be determined to design mine pillars using a proper sequence and exact mix of the three methods. A combination of these methods, in sync, can encompass the several advantages of the three methods while eliminating their disadvantages. This paper presents a conceptual three-tier solution to the pillar design problem, to improve its design pedigree, using a proper combination of numerical, analytical, and data-driven methods. At the focus of this proposed method lies the Ground Reaction Curve (GRC) concept.INTRODUCTIONAlthough the stability analysis of underground excavations is a challenging problem, its understanding has improved tremendously over recent years through the use of improved tools and techniques. The trial and error method was replaced with more scientific methods like the empirical and analytical methods that are still in use today. Empirical methods were developed based on large data sets obtained from experiments and observations (e.g., coal pillar strength equations). Analytical methods were developed based on mechanical understanding of stability (e.g., safety factor for vertical pillar loading, Convergence Confinement Method). Improvement in computing power and numerical techniques led to the development of several numerical methods (e.g., finite difference, finite element) suitable for geo-mechanical analysis.Each of these methods have certain advantages and limitations. Nevertheless, the user is often puzzled over the proper method selection and over the proper sequence of using them. This exercise becomes more challenging when different methods are combined, where, for example, one has to estimate the pillar strength based on empirical equations (e.g., Mark-Bieniawski coal pillar strength equation), determine the factor of safety based on an analytical approach (e.g., tributary area load divided by pillar strength), and analyze pillar-strata interactions using numerical analysis (see Esterhuizen, Mark, and Murphy, 2010b).Challenges increase when current pillar design methods are designed as passive structures to balance the fixed dead weight of the overburden. This classic suspension design approach does not recognize the self-stabilizing capacity of the overburden (Frith and Reed, 2018). A practical solution to address these issues is the use of numerical analysis. However, one should always keep in mind that the numerical modelling approach may have certain practical limitations."

Jan 1, 2019

By J. W. MacDonald

Review of equipment, performance, and shaft design plans including head-frames for sinking and forms for lining are given. Also included are comparative data for shafts of 11 x20 ft and 193/4 x 30 ft with 756 and 666-ft depths, respectively. Advantage from curtain wall installation with "slip forms" which warrant consideration for normal lining are outlined. A preliminary review is also made of "chemical grouting" to stop water inflow leakage with Halliburton equipment and service. Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review. These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work. TEST DRILLING Core test holes were drilled within each of the two shaft locations. Four additional cable tool holes were drilled on a radius of 700 ft from the shaft bottom to determine the coal seam elevations and govern the underground layout plans for each shaft. A graphic log of the hoist shaft test drillhole is shown by Fig. 1. A very soft sandstone was found at a depth of 16 ft. Cored recovery of the sandstone proved much weaker than the overlying compacted sand secured with coring facilities for soil recovery. Gradation from the very soft sandstone to fairly hard material occurred with the next 14 ft, extending to a depth of 30 ft. The weak character within the upper portion entailed need of adequate protection when sinking as described later. A part of the sandstone provided sufficient porosity and permeability to warrant further investigation. Adjacent cable tool drilling for temporary water supply disclosed inflow was limited to 2 gpm with a depth of 40 ft. It was increased to 12 gpm during the next 50 ft of drilling and occasioned subsequent precaution when sinking. General arrangement of facilities for sinking the hoist shaft is shown by Fig. 2. An available steel frame building was used to accommodate the hoist, compressor, shop, and shower or change room. The stiff leg derrick with 90-ft length of boom permitted removal of forms from the wood shop to the storage area or delivery within the shaft. Reinforcing steel and other needs were similarly handled, in addition to headframe erection. The headframe was placed over one end of the shaft to enable passage of forms for lining through the adjacent half next to the stiff leg derrick. The steel headframe as shown by Fig. 3 was fabricated locally. Side anchored cables from the

Jan 1, 1961

By D. C. Crowell, A. G. Loomis

Both Dimensional and Inspectional Analysis are developed from fundamental concepts , and dimensionless groups are derived which represent the viscous , capillary , and gravitational forces existing in two - phase , incompressible flow in petroleum reservoirs . It is shown how properly scaled models may be devised by means of the foregoing groups . Laboratory measurements with such models faithfully duplicate the behavior of the reservoir on a miniature dimensional and compressed time scale , and when all the pertinent variables are evaluated , the model is a most effective tool for the study of complex fluid displacements in the reservoir . Applying the Principle of Similitude , it is shown how dimensionally scaled models are applied to various types of reservoir displacements : ( 1 ) Oil displaced by water , ( 2 ) gas displaced by water , and ( 3 ) miscible displacement . The special case of water displacing gas by imbibition is analyzed , and it is shown that the dimensionally scaled model must be fabricated of sandstone rather than unconsolidated sand , which is generally used in such models . This report is intended to be a review and summary of the application of Dimensional Analysis to reservoir displacement problems for those who are beginning the study of this useful and interesting method .

Jan 1, 1964

By C. C. Birch

Due to grade estimation uncertainty, two statistical errors can occur. The Type I error is where material is classified as ore and mined, despite the true value being below the break-even grade. This material is dilution. The Type II error is where the material is estimated to be below the cut-off grade and is classified as waste, although the true grade is actually above the break-even grade. This material is not mined and is lost. The uncertainty was assumed to follow a normal distribution in a previous study. For this study, estimated block values are compared to those determined after mining (the best estimate of the true grade). This actual data from four mines shows that the uncertainty follows a Laplace. There is no single solution regarding adjusting the cut-off grade away from the break-even grade, considering estimation uncertainty, that could be applied to all gold mines. However, adjusting the cut-off grade downwards (up to 22% for one mine) is noted when optimizing the profit considering grade uncertainties. This type of adjustment could open up significant mining areas and extend the life of the mine.

Jul 2, 2022

By A L. Randriamanjatosoa, G Small, C Greet

In flotation simulation models, the effects of pulp chemistry other than pH are often ignored and reduced to particles hydrophobicity or contact angle, neither of which can be measured readily in real time in an operating plant. The flotation response of a given sulphide mineral is known to be influenced and can be improved by changing the chemical characteristics of the pulp during grinding and flotation. The on-line measurement of pulp pH, potential, dissolved oxygen, temperature and oxygen demand of a process stream was completed with the PCM® (Pulp Chemistry Monitor) developed by Magotteaux in this study. The data generated together with relevant plant operating parameters were used to construct an empirical model and simulate the metallurgical performance of the ore. The same approach was also applied to laboratory flotation tests data using various grinding media types. The flotation models better fit the actual data when the chemistry of the pulp is taken into account.CITATION:Randriamanjatosoa, A L, Greet, C and Small, G, 2018. Effects of pulp chemistry on plant and laboratory flotation modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 423–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By R. E. Lindstrom

Separation efficiency of a 4 percent divinylbenzene (DVB) resin is not altered over a wide range in temperature. A 12 percent DVB resin, however, exhibits a marked sensitivity to temperature. When flow rates are high at ordinary temperatures, 4 percent DVB resin exhibits higher efficiency, but at 200° F. both resins are equal in performance. Effective separation of rare-earth mixtures may be obtained with hydrogen as a retaining ion by maintaining column temperatures above the solubility of ethylenediaminetetraacetic acid (EDTA) in the free acid form. Slightly lower separation characteristics were obtained with this method as compared with copper as a retaining ion, Recovery of 99 percent of the EDTA from spent eluting solutions that contain copper has been accomplished by a calcium-copper displacement reaction followed by EDTA precipitation. Impurities in the product are correspondingly low. Recoveries of EDTA from holmium solutions with sulfuric acid are substantial; however, those from yttrium solutions are quite modest. Radiotracer experiments show the presence of approximately 0.1 percent yttrium contamina¬tion in the recovered material. The study presented is one phase of a broad research program designed to assist the technology of separating and purifying rare-earth elements.

Jan 1, 1961

By Armando Vazquez Arredondo

Tenova Goodfellow Inc. has successfully installed the proprietary EFSOP® (Expert Furnace System Optimization Process) system in over 80 installations worldwide. For over 15 years, the EFSOP® System has successfully achieved its main objective of improving performance and operating costs through the reduction of electricity, oxygen, methane, injected and charge carbon use. Using the off-gas information provided by the EFSOP® System, Tenova Goodfellow Inc. has now developed a solution for detecting abnormal water events within the EAF steelmaking process. When water form enters the EAF, it immediately forms into water vapor (H2Ogas) and a proportion of the resulting water vapour will further react and dissociate to H2. Effective water detection technology must be capable of detecting BOTH forms of water; H2Ogas & H2. Tenova Goodfellow has the technology to measure in real time and simultaneously H2Ogas & H2. This paper will provide a summary on how the EFSOP Water Detection Technology® is used during the EAF operation. Details regarding the technology, software, alarm rate and information on sensibility water trial tests will be provided within this paper.

Aug 16, 2017

By R. Q. Honaker

A significant problem in ultrafine particle classification is the significant amount of submicron particle by-pass to the coarse particle stream. In classifying cyclones, submicron particle by-pass to the underflow stream can be reduced by decreasing water recovery. Past studies have shown that a reduction can be realized when the feed solids concentration is increased or the apex diameter is reduced. However, both adjustments tend to increase the particle size cut point and negatively affect classification efficiency due to the impact on slurry rheology. The addition of a viscosity modifier to the feed stream of a classifying cyclone improved the classification performance and decreased the particle size cut point over a range of feed solids concentrations. The detailed test program investigated the use of the modifier in conjunction with varying apex diameters to identify conditions that minimize ultrafine by-pass. With small apex sizes, roping conditions were readily eliminated by the addition of viscosity modifiers. The addition of the modifier had no deleterious effect on froth flotation performance, which commonly serves as a downstream separation process. The fundamental and practical benefits of viscosity modifiers in classification processes are discussed in this publication.

Jan 1, 2006

By Herty, C. H.

Iron oxide (FeO) plays an extremely important part in the manufacture of iron and steel. In the three major processes- blast-furnace, open-hearth, and Bessemer converter-iron oxide is the chemically predominant compound and controls to a large ex- tent the operation of the furnaces and the composition and quality of their respective products. In order to emphasize the importance of iron oxide in each process, they will be considered individually in some detail. THE OPEN-HEARTH FURNACE. Iron oxide is introduced into the open-hearth furnace in four ways : 1. The scrap charged into the open hearth is oxidized by the furnace gases, the amount of oxide formed depending primarily on the amount and type of scrap charged. It has been found' that with large scrap, 1.7 Ib. of FeO is formed per 100 Ib. of scrap charged, whereas with scrap of medium size about 5.3 Ib. of FeO is formed per 100 Ib. of scrap charged, when the period between the charging of the scrap and the addition of hot metal is 3 hours. 2. The decomposition of the limestone sets free CO, by the reaction

Jan 1, 1957

Placing a detonating explosive inside a volume of rock is an efficient method of rock fragmentation. The explosion generates internal tensile stresses in the rock, and because rock is a brittle material, this brings about crack propagation and fragmentation far more efficiently than does application of explosive on the surface. To get the explosive inside, we drill a pattern of boreholes and charge the explosive into the holes. This is really the one and only purpose of making blastholes in mining: to give access for the explosive to the interior of the rock. No matter how big and expensive a drilling jumbo we stand up in front of a rock face, and no matter how many boreholes we let it drill, the rock does not fall apart by itself without blasting. It is the action of the explosive in the boreholes that does it. When we consider that we need a pound or two of explosive for every cubic yard of rock to be fragmented, and a pint of borehole volume for each pound of explosive, we see that the process of blasthole charging is an important element in the whole process of rock blasting.

Jan 1, 1975

By B. E. Field

Cobalt is a silvery white metal with a slight bluish cast. It strongly resembles nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ decidedly in their properties from those of nickel. The name "cobalt" was derived from the German Kobold, meaning goblin, and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was not isolated until about the middle of the eighteenth century, by Brandt, although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470.

Jan 1, 1935

By Berk. A. A.

"INTRODUCTION Corrosion of sections of piping used in steam-heating systems is frequently regarded as unavoidable, and periodic replacement is provided. Surfaces exposed to newly condensed steam appear to be especially vulnerable to attack. As an added nuisance, solid products of the corrosion tend to accumulate, plugging return lines.The trouble is ascribed in the main to carbon dioxide and oxygen 3/ 4 / 5/ 6/ dissolved in the condensate. When oxygen is the principal factor, the corrosion usually is characterized by pitting. Carbon dioxide tend3 to cause an acidic condensate which dissolves the metal more uniformly and produces the familiar failure at threaded areas where the piping is relatively thin, and where high stress may tend to acceletate the attack. Carbon dioxide enters the system with the feedwater, generally in a combined form such as carbonates and bicarbonates. Oxygen enters both with the raw feedwater-and as air leaking into lines under partial vacuum. The larger central-heating plants have sought to reduce corrosion by eliminating these gases as much as possible. A smaller plant ordinarily lacks the equipment and technical supervision required for this purpose."

Jun 1, 1944

By E. P. Youngman

Tantalum is a rare element ; estimates indicate that there is less tantalum than gold in the earth's crust . After remaining a laboratory curiosity for many years , it was used to a limited extent and for relatively few years (1903- 1911) for incandescent electric-light -bulb filaments . Another wave of interest in tantalum appeared when its electrolytic-valve action was taken advantage of in charging storage batteries , especially for radio work . Tantalum chargers were eventually displaced by other types of chargers , but for a time they were manufac tured in sufficiently large numbers to create a demand for the metal and to bring about its production on a commercial scale in the United States . As tantalum became available in larger quantities and at substantially lower prices , and as high prices for platinum encouraged the employment of tantalum as a substitute , the metal was put to many new uses . Ferrotantalum was made and sold before the World War , and patents have been taken out for a number of special alloys for industrial purposes , but probably the largest use for the metal to-day is in vacuum tubes .

Aug 1, 1930

By R. M. Beauchamp

Base metal processing operations often treat process tailings and acid mine drainage using a high density sludge (HDS) water treatment process. Lime is used in this process, which reacts with existing sulfates to form gypsum. When a recycle stream is incorporated in the process, gypsum levels in recirculating water may build up and cause high levels of gypsum supersaturation. Precipitation of gypsum from the supersaturated process water causes many problems. It is speculated that gypsum may precipitate on sulfide minerals and silica gangues in the flotation circuit, resulting in decreased selectivity and recovery. An understanding of the determinants and nature of precipitation may provide solutions to mitigate the formation of precipitates and improve flotation performance. This study showed that both sphalerite and silica exhibited gypsum- or calcium carbonate-like behavior in the respective supersaturated solutions, indicative of a coating of calcium species on the mineral particle surfaces. The addition of copper sulfate and/or potassium xanthate had little effect on the precipitation of gypsum or calcium carbonate on the mineral particles. Sodium carbonate is encouraging as a method to minimize calcium species interactions on sphalerite/silica surfaces.

Jan 1, 2006

By Zhenfeng Zhou, Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

The oxygen blast furnace is a new technology for ironmaking, where the oxygen and CO2-stripped blast furnace top gas are blown into the blast furnace replacing the conventional hot air. The oxygen blast furnace could reduce the consumption of coke and emission of carbon dioxide. In this chapter, a three-dimensional numerical model was developed to simulate the lance-blowpipetuyere-raceway region of a blast furnace, and the flow and combustion behaviors of coal particles were investigated based on an oxygen blast furnace. Compared with the traditional blast furnace, the combustion characteristics in the raceway of the oxygen blast furnace were different. In addition to the combustion of coal and coke, the combustion of large amounts of reducing gas was included. The coal combustion of different oxygen content (70, 80, 90, 100%) were investigated. The simulation results indicated that the coal burnout was only 21.64% at an oxygen content of 70%, a decrease of 51.52%, compared with a traditional blast furnace. The coal burnout was increased with the increase of oxygen content. When the oxygen content is 100%, the coal burnout was 90.38%, an increase of 17.22%.

Mar 1, 2017

By James J. Anthony

High-angle in-pit conveying is an idea that is being seriously studied by a number of important mining companies in North America. Its application in coal, iron ore, and copper mining is expected to reduce mine operating costs considerably compared with the conventional discontinuous methods, such as truck haulage, which are fuel, labor, and maintenance intensive. Therefore, a mine introducing high-angle in-pit conveyors will gain a competitive advantage over mines which continue to use conventional haulage. While the capital outlay for in-pit conveyor systems obviously varies depending on pit depth, the angle of incline, and the capacity required, it generally will not exceed that of truck haulage when all Factors are taken into consideration. These factors include the cost of excavation, as measured in relation to the volume of minerals mined, the cost of building truck ramps and roads, and the capital outlay for the trucks and maintenance facilities. In many cases, in Fact, the capital outlay will be less than for truck haulage. This cost advantage will best be realized by new mines, whereas in existing producing mines the switch from truck haulage may involve the abandonment of a substantial capital asset.

Jan 1, 1983

By S L. Barbour

Measurement of the net percolation from the base of a cover system into the underlying waste material is a key component of a cover system monitoring program. The units of measure (ie a percentage of precipitation or rainfall) are simple to understand for all stakeholders, which increases the importance of obtaining representative net percolation values. In general, lysimeters are used to measure net percolation across the cover material-waste material interface; however, the design of lysimeters for cover system monitoring programs in the mining industry have typically not considered fundamental aspects of lysimeter design. Lysimeter design is typically thought of as being conceptually simple, when in reality the design, installation, and operation of lysimeters is often counter-intuitive, due to the complexities of flow through unsaturated soil systems. This paper puts forward a methodology for lysimeter design while also presenting the fundamental design variables that should be considered. Lysimeter design for differing climates, cover materials, and waste materials is discussed. Finally, the performance of lysimeter designs previously installed in the field at sites in Australia, Canada, and the United States are subjected to numerical modelling to determine whether net percolation is being measured properly.

Jan 1, 2003

By C. L. Karr

U.S. Bureau of Mines (USBM) research has shown that fuzzy logic and genetic algorithms (GA's) have great potential for industrial process control. A technique has been developed by the USBM in which GA's are used to substantially reduce the time needed to design fuzzy logic controllers (FLC's).This technique shows promise as an efficient, robust approach to developing control systems. The research described in this report is twofold. First, the basic approach to developing an FLC using GA's is presented. The GA-designed FLC is developed for a specific physical system, a pH titration system. Second, empirical results are presented in which variations in the FLC implementation are compared. Specifically, the effects of altering five aspects of the pH FLC are considered: (1) membership function form, (2) number of fuzzy classes, (3) the center-of-area method, (4) implication operator, and (5) fuzzy rule form. Results indicate that (1) the technique in which GA's are used to design FLC's is effective, and (2) when this technique is used, variations in FLC implementation have little effect on FLC performance in a chosen control problem.

Jan 1, 2010

By J. R. Heberger, B. H. Ngo

The Safety Pays in Mining v2.0 web application, developed by the National Institute for Occupational Safety and Health (NIOSH) Mining Program, helps mines determine the potential costs associated with mining injuries. This web app categorizes injury cost by part of body injured, by the cause of the injury, or by the nature of the injury. When the user selects one of over 150 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, Safety Pays in Mining v2.0 will estimate the total costs of the selected injuries and the estimated impact of total injury costs on mining company profits and will provide some examples of services and personal protective equipment on which companies could spend the savings that result from the prevention of injuries. This paper reviews the Safety Pays in Mining version 2.0 web application by discussing the development and updates to the app, how it is used to show the true costs of mining injuries, and how mines can benefit from using this app.

Feb 1, 2024