Search Documents

By L. G. Austin

Introduction My first contact with industrial milling was during the time I worked in the electricity generating industry in the United Kingdom. In visits to power stations to investigate either deposits in the boiler furnaces or polluting deposits settling around the stacks. I had to check the performance of the vertical coal pulverizers, since poor pulverization aggravated both problems. Naturally, then, when I came to the USA in 1957 to take a PhD in fuel technology at Penn State, I was put to work to review the science of coal pulverization. After this reviewing, I was completely confused. On one hand, there was a well-developed understanding of stress-strain equations, and a rap- idly developing knowledge of how stressed, brittle solids fractured, based on the Griffith crack theory. On the other hand, reading in the grinding literature gave me: • Kick's Law, which was clearly not correct in the light of modern fracture theory; • Rittinger's Law, which was also clearly not correct; • Bond's Third Law of Comminution, which was claimed to have something to do with the Griffith crack theory, but where the connection between the two was made by intuitive pseudo- scientific reasoning I could not accept; • the choice of mill motor power for the most common type of coal mill, the Raymond pulverizer, was calculated from the fan power required to move air through the mill. Although I could accept the empirical connection between the two, it made no sense from the point of view of fracture energy. Even today, most books or review chapters on size reduction start from these laws. incorrect statements abound in the literature, such as “the Hardgrove Index is based on Rittinger's Law," which it is not, "The Bond theory states that work input is proportional to new crack tip length produced in particle breakage," which is not true, etc. My own test work showed that these "laws" did not fit the data for grinding of coal. At about this time, Epstein (1 948) and Broadbent and Callcott (1 956), following the original work by R.L. Brown (1941) at the British Coal Utilization Research Association, proposed describing breakage as a series of fracture stages. I took their concepts and developed the basic differential equation for a batch grinding process continuous in time, analogous to a batch chemical reactor. Robin Gardner then joined the project and did his PhD on treating batch grinding in the same way as a batch chemical reactor. He found that the basic equation had already been partially derived by Sedlatschek and Bass (1 953) in Germany. We confirmed experimentally the validity of the equations for describing batch grinding (1 962) and formulated the equation describing steady-state continuous grinding in a fully-mixed mill. At about the time this work was published, Gaudin and Meloy (1962) and Filippov (1961) independently published essentially the same equations, but without experimental proof of the validity of the concepts. I will give a brief overview of what these beginnings had led to in the design of mills for size and power, and show some of the results of this more detailed understanding of grinding processes. Concepts of Fracture Mills such as tumbling ball, rod, pebble and autogenous mills and vertical mills such as the Raymond, and E-type apply compressive stress to lumps or particles relatively slowly. Compressive stress applied to a particle of an elastic brittle solid imparts overall strain energy to the solid and produces local regions of tensile stress, (Fig. 1) (Berenbaum and Brodie, 1959). Irwin (1949) showed from solution of the stress-strain solutions that a small hole in a region of tensile stress reduces stress concentration at the hole, that is, the tensile stress at the tip of a crack or flaw in a solid is much higher than the general tensile stress in the region. The longer the crack, the higher the stress concentration. Griffith (1920) hypothesized that when the regional tensile stress is large enough, then the chemical bonds at a preexisting crack tip are stretched to breaking point, as illustrated in Fig. 2. When the bonds break, the crack becomes longer, the tensile stress concentration increases, the situation is unstable and a crack opens up (propagates) a surface of tensile stress, creating its own tensile stress at the leading edge. Stored strain energy is converted to the kinetic energy of the moving stress field, which is analogous to sound propagation through the solid, so the crack tip accelerates to velocities approaching those of sound. The moving crack will pass through regions that were previously under regional compressive stress. The equations for "ideal" and "Griffith" strengths are where a is the intermolecular distance, y is Young's modulus, g is the energy

Jan 1, 1998

By S. W. Ross

In 1936 a description of the plant (Fig 1) and process employed by the Electrolytic Zinc Co. of Australasia Ltd. for the recovery of zinc from zinc concentrate by the electrolytic process was prepared. † During the twelve years which have elapsed since the preparation of the earlier paper, several major changes in the metallurgy of the process have been introduced. It is the purpose of the present paper to give a general description of these changes and thus to bring up to date the description of the plant and process. Summary The major changes in Risdon practice since 1936 have been: 1. Replacement of two stage roasting by a preliminary roast followed by the flotation of all the leach residue and the roasting of the flotation concentrate. 2. Screening of all calcine fed to the pachucas. 3. Continuous leaching of calcine and improved classification of pachuca discharge. 4. Close control of hydrogen ion concentration during purification for iron removal. 5. Recovery of cobalt as a good grade oxide. 6. Production of part of the zinc output in the form of "four nines" metal (99.99 pct purity). 7. Closer spacing of electrodes thus increasing the potential output of cathode zinc per cell by 50 pct. Changes which are in prospect and for which construction work is proceeding at the present time involve the starting up of: 1. Two suspension roasters. 2. A contact acid plant to produce 150 tons‡ of acid per day and replacing the existing Mills Packard chamber plant. 3. Extra power station capacity to permit greater current flow to existing cell room units. This will increase the output of cathode zinc from about 245 to 290 tons per day. Plans for the future envisage the building of an ammonium sulphate plant, the first unit of which will produce about 50,000 tons per year, and improved treatment of zinc plant residue for the recovery of zinc, lead and other metals. At the end of this paper tables of metallurgical data are presented relating to the year ending June 30, 1948. Details of Changed Practice Output In 1936 the production of cathode zinc amounted to about 200 tons per day. This has since been increased to about 245 tons per day while plant extensions are practically complete which will permit of an output of about 290 tons per day in the near future. Roasting Division ROASTING POLICY A major change has occurred in the roasting policy. Twelve years ago the method in use was to carry out a two stage roast in the first stage of which sulphide sulphur was reduced to about 6 pct. The pre-roast calcine was re-roasted in modified Leggo furnaces using coal as fuel, sulphide sulphur being reduced to about 0.8 pct. The whole procedure was described on pp. 482491 of the earlier paper. Although this roasting procedure had certain advantages it possessed some distinct disadvantages. For instance, it appeared uneconomical to heat up the entire input of pre-roast calcine to roasting temperature by the expenditure of fuel in order to oxidise a few percent of sulphide sulphur. It was argued that if the pre-roast calcine were leached and a process could be developed for the recovery of a zinc sulphide concentrate from the leach residue, this concentrate, small in weight compared with the pre-roost calcine, would probably roast autogenously, thus virtually eliminating the expenditure of fuel as well as greatly increasing the weight of sulphur oxidised per square foot of furnace hearth area. The obvious method of producing a suitable concentrate from leach residue was by flotation. It will be recalled (see p. 495 of the earlier paper) that when two-stage roasting was practised the leach residue was classified, the granular fraction was ground and floated while the slime fraction was thickened, filtered and dried ready for shipment to a lead smelter. This process worked quite successfully. However, when trials were made of leaching a calcine carrying several percent of sulphide sulphur the granular fraction still floated well, but the slime fraction carrying 8-10 pct sulphide sulphur yielded very poor results when subjected to flotation. This fact held up the application of "pre-roast" leaching for many years. However, successful flotation of the slime fraction of leach residue was finally achieved and in August 1940 the slime flotation plant began operation, while the leach-

Jan 1, 1950

By C. H. Cheng, C. E. Birchenall

The fundamental problem in the thermodynamics of solid solutions is the determinatiorl or calculation of the activities of the components as a function of temperature and composition. Since the theory of metals is not suficiently developed to allow a priori calculation of these quantities, they must be obtained from experiment. C. Wagner1 has reviewed the literature of this subject for the period before 1940. Although several important and extensive studies have been made in the meantime, the number of systems to which any sort of quantitative information can be assigned is vanish-ingly small. These data have become of great potential importance in studies of the structure of solid solutions2 and intermetallic compounds, the nature of the diffusion process,3,4 and perhaps even the mechanism of mechanical deformation.5 For these reasons, it. seems very worthwhile to extend the experimental data in this field. Although there is little use in duplicating Wagner's review, attention should be directed to the most recently reported investigations. A brief enumeration of the methods of measurement previously employed also should be valuable. The most direct method is the determination of the partial pressure of the components in the vapor phase in equilibrium with the solution. Both equilibrium and kinetic methods have been tried in metal systems, but almost exclusively on liquid phases. Only in the ease of carbon in iron alloys and in the copper-zinc system have extensive measure- ments been made which include solid phases. When one of the components is an element, such as nitrogen or carbon, which forms compounds which are very volatile and stable at normal temperatures and pressures (CH4, Co2, CO NH3), it is frequently possible to equilibrate mixtures containing these (such as CH4-H2, CO2-CO, NH3-H2) independently with the elernents (C, X) and with the metal (Fe, Ni, etc.). Such measurernents have been made for carbon in iron, iron-silicon, and iron-manganese alloys by Smith6 and in iron and iron-nickel alloys by Toensing.7 Differences between carbon activity values at the same temperature and carbon content when carboil is introduced from CH4-H2 rnixtures or CO-CO. mixtures indicate that the effects of hydrogen and oxygen in the system are not negligible, and one can only hope that the true value lies somewhere between these sets of results, probably nearer the CH4-H2 data since hydrogen is less soluble in iron than oxygen. This is essentially an equilibrium method, although flowing gas is employed. A kirletic method has been employed which consists of sweeping an inert gas (generally hydrogen) over the alloy at a series of rates, condensing the metal vapor out,, and analyzing it. The metal content can be extrapolated to zero flow rate (equilibrium). Wejnarth's8 work on Cd-Mg and Zn-Mg is a good example of this frequently used method. A variant of this consists of equilibrating a known volume of inert gas with the alloy, sweeping it out quickly, and analyzing for metal. In common with the above method, it has the disadvantage that the "inert" gas is generally somewhat soluble in the alloy. Moreover, the former continuously displaces the system from equilihrium and may give low values if solid diffusion is involved. The dew point method applied by Hargreaves9 to the alpha and beta brasses and by Schneider and Stolll0 to A1-Zn avoids the introduction of another component to the system, but is useful only in systems in which one component is much more volatile than the other. The alloy sealed in one end of an evacuated silica tube is heated to the desired temperature. The temperature of the other end is lowered until droplets of the volatile component condense. When the temperature is raised slightly, the droplets will evaporate. By careful adjustment of temperature, the range between evaporation and condensation can be narrowed appreciably. An independent determination of the vapor pressure of the . pure volatile component is necessary to give the partial pressure over the alloy. This is the method employed here to determine the vapor pressures of zinc and cadmium over their silver alloys up to 34 pct in cadmium and 76 pct in zinc. The former involves only the a solid solution, but the latter covers the a, ß, y, and e fields. In recent determinations, Herbenar, Siebert, and Duffenbarkl1 used the

Jan 1, 1950

By A. T. Iannacchione

Synopsis Underground stone mining Is an emerging sector of the U.S. mining industry. As this expansion takes mines under deeper cover, and as more efficient mining methods are utilized, effective stone pillar design methods will become even more Important. Current design practices are examined and a discussion of safe mine layouts is presented as a first approach towards weighing the demands for increased production against increased risk. Risks to underground stone-mine workers include rib Instabilities, pillar failures and roof falls. Seventy-two stone-mine pillar designs were examined. Pillars with width to height ratios of less than 1.5 appear more likely to fail when subjected to excessive stress levels. When width to height ratios fall below 1.0 defects in the pillars, such as through-running discon¬tinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties and orientation are also important determining factors in pillar strength. During the past three years the number of active underground stone mines in the U.S.A. has ranged between 90 and 100. This number is expected to increase as the crushed stone industry responds to growing demands for its products.1 As more of the industry moves to benefit from the advantages of underground mining production from underground stone mines is expected to increase above its current level of approximately 66 000 000 r/year. Parker2 identified four advantages of underground mining operations: (1) surface developments, zoning laws and environmental concerns are often less of an issue; (2) stripping and restoration requirements are eliminated; (3) additional reserves are often available beneath the quarry floor, under pit slopes or under an adjoining property; and (4) space is created for secondary use. Underground mines enjoy the added benefits of work in a constant underground climate, rather than in the variable surface climate, minimization of community concerns by placement of the crushing, sizing and stowing operations underground and reduction of surface vibration concerns through smaller blasts. The drawbacks of underground mining include added health and safety hazards for the stone miners, whose health can suffer from increased exposure to falls of ground, airborne contaminants and fog in large underground openings. Injuries from falls of ground in stone mines have occasionally exceeded the incidence rates for other mineral resources mined underground. 3 Existing underground stone operations, by comparison with stone operations a decade ago, mine more stone at a faster rate and with larger equipment. Because of high demand mines face increased pressure to yield more stone per production blast. A majority of the miners use the V-cut blasting pattern, which limits the depth or pull for each shot to about 4 m. Therefore, to produce more stone, either the mines must work more faces or existing faces must be enlarged. The enlargement of underground openings poses problems in the maintenance o€ strata stability, First, the widths of the mine entries partially control the amount of sag or deflection that any given roof beam can withstand before failure. This deflection can take pi ace quickly after an opening is excavated or much later as weathering processes form additional, thinner beams. Because increased deflection increases the potential for roof beam failure, there is a limit to how wide a room can safely be made. These limits depend on local geological and stress conditions and, to some extent, the cost effectiveness of roof-bolting. Given these room width limitations, underground stone mines have placed more attention on expansion of production through benching where mining thicknesses permit. The heights of rooms partially control the strength characteristics of adjacent pillars: as the room height increases for a given pillar width the pillar width-to-height ratio (w/h) decreases. In general, stone pillars are very strong, but when the width-to height ratio diminishes the potential for pillar rib instabilities and pillar failures increases (see Fig. 1). [ ] In the underground environment the desire to utilize wider rooms, higher benches and multi-level mining results in the potential for unstable ground conditions. Although the number of failed pillars is currently very low, the potential for additional failures will grow if more slender pillars are developed, especially under deeper cover, with wider mining sections and in multi-level operations. It should also be noted that the passage of time acts to decrease the strength of many existing pillars. An examination of current design practices

By L. R. Raymond, G. G. Binder

One primary purpose of hydraulic fracturing as a well stimulation technique is to overcome formation damage. The literature provides ways of designing fracture treatments and evaluating their results but not of incorporating formation damage in vertically fractured wells. Results of an investigation of this problem are presented in this paper. Prediction of stimulation ratios in vertically fractured, damaged wells is accomplished with a mathematical model relating stimulation ratio to relative conductivity of fractures whose lengths are not more than about half the drainage radius of the well. Comparison of results from the new model to results in published predictions verify its utility; these results also show that the range of stimulation ratios that can be predicted for undamaged wells is extended to include relative conductivities of less than 300. This extension is important when using fracturing to stimulate wells with high production rates and high native formation permeabilities. For example, large increases in daily oil production rate can be obtained with stimulation ratio increases as low as 1.25. The importance of complete fracture fill-up (uniform proppant packing) is shown through use of the mathematical model. If, at the mouth of a fracture, only a small fraction (1/2 percent) of the total fracture length is not packed with proppant, nearly all the polential stimulation increase is lost. Proppant crushing, compaction and embedment have been shown in laboratory studies to be responsible for low fracture conductivities in wells producing from highly stressed formations. Equipment and methods for testing the effect of stress (overburden) on conductivity of fructures in consolidated and unconsolidated sands are discussed in this paper. Laboratory tests with simlilated fractures in cores from both types of formations showed that crushing, compaction and embedment seriously affect conductivity. Results indicate that similar laboratory tests should be made when accurate knowledge of fracture conductivity is needed to assure good stimulation results for important wells. The chief factor in stimulation ratio reduction was found to be overburden pressure, but the size and type of proppant and the hardness of the formation have significant effects. Fracture conductivity reductions of up to 50 percent were observed with sand propping fractures in consolidated cores; a reduction of 83 percent was measured for an unconsolidated core. The range of effective overburden pressures for which conductivities were measured was from 100 to 5,000 psi. An example fracture design and evaluation problem indicates the usefulness of considering formation damage in planning well stimulation jobs. When damage exists, but its extent and the degree of permeability reduction are not estimated from diagnostic tests, the formation permeability used in planning the job may lead to under-designing. As the example shows, too low a target stimulation ratio can lead to much lower production rates (by half) than could be attained otherwise. Solutions of equations representing several special cases of the mathematical model are presented in graphical form and details of the derivations of the equations are given in the Appendix. INTRODUCTION Since its inception in 1947, hydraulic fracturing has proven to be an effective and widely accepted stimulation technique. In the past 18 years the ability to execute a successful hydraulic fracturing treatment has been substantially increased. The development of design and evaluation procedures1,2 has been one of the major contributions to this increased skill. However, as the art of hydraulic fracturing has moved closer to a science, new problems concerning the design and evaluation of the optimal hydraulic fracturing treatment have arisen. Three questions are pertinent to these problems. I. How is a fracturing job evaluated in a damaged well? 2. What is the effect on the stimulation ratio of not filling the fracture in the vicinity of the wellbore? 3. What is the effect of overburden pressure on fracture conductivity and, consequently, the stimulation ratio? A primary objective of fracturing a well is to stimulate production by overcoming wellbore damage. Presently. however, there is no rational basis for designing or evaluating the optimal fracturing treatment in a damaged well. All present fracture design and evaluation techniques assume that proppants can be uniformly placed in fractures. This assumption may be in serious error, particularly for the portion of a fracture directly adjacent to the wellbore. In this area, turbulence of the injected fluid can cause the proppant to be swept farther into the fracture. Also, loss of fluid from the fracture to the

By R. V. McAfee

The fundamentals of vertical-lift performance are examined with the aid of computer-calculated flowing gradient charts. Flowing and gas-lift well performance characteristics are determined from available well test data. The effect of tubing size, gas-liquid ratio and wellhead pressure is discussed for both flowing and gas-lift wells. The effect of gas-injection pressure, formation gas, bottom-hole pressure and valve spacing is also discussed for gas lift wells. From these studies conclusions may be reached for improving or prolonging natural flow, obtaining optimum lift efficiency when natural flow ceases and improving existing gas-lift systems. The techniques perfected satisfy the requirement that the time involved to conduct an evaluation be practical for operating personnel. INTRODUCTION Flowing pressure gradients furnish the key to successful evaluation of vertical-lift performance in producing wells. Command of multiphase flow gradients in some readily usable form is a necessity before operating personnel can competently include vertical-lift performance evaluation of both flowing and artificial-lift wells in their over-all consideration of production efficiency. A readily usable form cannot be overemphasized since most of the decisions which confront the production engineer with a problem well must be made quickly. In moving a barrel of oil from the reservoir to the stock tank, the major portion of energy generally is expended in the vertical-lift phase. This may or may not be of concern during the flowing life of a well, depending upon the production requirements. It becomes of some concern when the flow performance of the well becomes erratic, and a conscious effort must be made to maintain natural flow. It is at this time that the first steps may be taken to modify existing conditions to relieve unnecessary limitations to proper flow. When natural flow ceases and some form of artificial lift must be installed, the amount of energy expended in lifting liquids becomes quite obvious. It is at this time, if no other, that lifting efficiency becomes important because that part which must be supplied from an outside source is now related directly as a cost per barrel of oil produced. Ten years ago, the majority of gas-lift wells were produced with gas-well gas. Today, the majority are produced by closed rotative gas-lift systems. This permits a direct evaluation of well performance in terms of horsepower requirements and has resulted in mixed conclusions as to the success of gas lift based upon the relative efficiency of a particular system. An increased awareness of the need to resolve vertical-lift performance on a readily usable, scientific basis was inevitable. An indication of the need for better applied science in this field is the often-asked question of whether or not gas-lift can efficiently deplete a given well or reservoir. This question cannot possibly be answered without first evaluating reservoir, surface and vertical-lift performance both as encountered today and as anticipated throughout the life of the well or wells. The technique presented in this paper was originally developed to upgrade gas-lift installation design from an applied art to an applied science. It has since been successfully used not only for this purpose, but also for the whole field of vertical-lift performance in its broadest sense. Lift efficiency should be considered important while the well is still flowing, as well as after natural flow ceases. Correct interpretation and proper modification of the vertical-lift performance of a producing well can provide dramatic improvement in production performance and/or efficiency. STATEMENT OF THEORY AND DEFINITIONS Fig. 1 illustrates the three divisions of production which will be used in this paper. The terms are a modified version of those presented in the very fine paper by Gilbert.' The fields of reservoir and surface performance both have been greatly improved over the years. A study of those writings which may be found indicates that the field of vertical-lift performance has not progressed as well. There are two possible reasons for this lack of progress. 1. It has not been recognized as a scientific field in itself by the oil companies, as has reservoir engineering. 2. The equipment companies have confined their efforts to mechanical design research rather than the more basic study of vertical-lift performance of producing wells. Both organizations must have an economic stimulus for doing research in this field, and most of the results obtained in past work has been so erratic as to arouse little enthusiasm. The basic purpose of interpreting vertical-lift performance is to predict operating conditions below the surface of the ground from available data. The success of the interpretation depends upon the accuracy with

By S. J. McCarroll

Fig. 1—The belt shown at right carries filter cake to mixing station over calciner. Crude ore conveyors appear in right background. THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.' During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO2 process was constructed. Numerous operation difficulties ensued, and the plant. was closed when the manganese situation in the country eased. In 1949 Hewitt S. West initiated negotiations to acquire the plant. In 1951 Manganese, Inc., was formed and contract entered into with the General Services Administration to supply 27 million units of metallurgical grade manganese in the form of nodules to the national stockpile. A second contract was made to upgrade 285,000 tons of stockpile ore. Test work was undertaken by the Southwestern Engineering Co. and likewise by the Boulder City pilot plant at the U. S. Bureau of Mines. Results obtained indicated the commercial feasibility of the flotation process. Construction of the plant, which is shown in Figs. 1 and 2, was started in June 1951, and operations on a break-in basis began in September 1952. Apart from the usual starting difficulties two major disasters caused serious setbacks, one a kiln failure in February 1953, and the other a fire that destroyed the flotation building in June of the same year. The nodulizing section of the plant resumed operation in November, and the flotation section in January 1954. The ore minerals are chiefly wad,* with minor amounts of psilomelane, and occur in sedimentary beds of volcanic tuff. The ore is overlain with beds of gypsum which outcrop or may be covered with surface gravel. Intermediate beds of red and white tuff occur frequently with lenses of red and green jasper and stringers of gypsum and calcite. Small amounts of iron are present; lead content averages about 1.0 pct and minute amounts of copper and zinc are found. Barite, celestite, and bentonite are present. Since these are made up of minute asicular crystals, moisture content is very high, averaging about 18 pct. Ore reserves have been estimated at 3 million tons averaging 18 pct Mn2 and up to 5 million tons after grade is dropped to 10 pct Mn. A good part of the orebody was stripped of overburden by the previous operating company . Approximately 50 pct of the ore, representing more than 60 pct of the manganese, can be mined by open-cut methods. A system for underground min- . ing has not yet been decided on. Open-cut mining with benches of 20 ft has proved satisfactory. Although the ore is soft and appears dry and dusty it has a certain resilience, probably due to the porosity and moisture which makes drilling and fragmentation difficult. Wagon drills have been abandoned in favor of the Joy 225-A rotary drill which will put down a 43/4 -in. hole at the rate of 2 ft per min. Holes are spaced in a pattern with 8 to 9-ft centers. Forty percent powder has been used, but better breaking to 2-ft size is obtained with low velocity bag powder of 30 pct strength. Loading is done with one 21/2-yd shovel, and cleanup follows with one D-7 bulldozer. The ore is hauled with Euclid trucks about 1000 ft from the pit to a blending pile, where the daily mine production is spread in layers by bulldozing until approximately one month's mill feed is accumulated. A new pile is then started and mill feed is drawn from the first pile by one 13/4-yd shovel and Euclid trucks, with a haul of approximately 500 ft. Mining is performed by an independent contractor with engineering and supervision by the company staff. Early test work indicated that the manganese could be floated with soap, a wetting agent, and fuel oil to give a recovery of better than 75 pct with a grade of 43 pct Mn. The concentrate when nodulized with coke would upgrade to 46 pct Mn or over, and the lead volatilized to 0.6 pct residual.

Jan 1, 1955

By C. R. Bailey, H. F. Dunlap, Ellis Shuler, H. L. Bilhartz

Data are presented which indicate that the saturation exponent, n, in the equation, R. = R100S-11, relating core resistivity, I:,. to the resistivity at 100 per cent saturation. R100. and to the saturation, S. may vary appreciably from the value of two which is usually assumed for this exponent when interpret ing well logs. Values ranging from one to two and one-half have been found on (.ore sample investigated to date. Attempts to correlate this saturation exponent with porosity or permeability of the core have not been successful. The saturation exponent is apparently not a function of the interfacial tension between the brine and the displacing fluid. Some evidence is given indicating that the resistance of the core is not a unique function of the saturation but depends upon the manner in which this saturation was achieved. Equipment and technique are discussed for measurement of resistivities in core plugs in which water saturation can be varied. lNTRODUCTION A number of investigations of the resistivity-saturation relationship for un-c~~nsolidated sands and consolidated (.ore samples have been reported in the literature. According to most of these: R. = R¹ººS², where R² = the resistivity of a formation at saturation S, and R¹ºº= the resistivity of the formation at 100 per cent water saturation. Much of this work was (lone on unconsolidated sands desaturated by gas or oil. Hen-clerson and Ynster worked exclusively with dynamic systems, flowing oil or gas through consolidated cores. There is some doubt as to how well this reproduces static reservoir conditions. Jakosky and Hopper³ onsidered also the case of consolidated core plugs, but the oil-water distribution in the emulsions which they used to saturate their cores is almost certainly different from that occurring in reservoirs. Recently Guyod quotes the results of some Russian work which indicates that n may vary from 1.7 to 4.3. No experimental details of this work are available. In connection with electric log interpretation it is important to know the value of the saturation exponent. For example, if in a given reservoir it is found that the resistivity is three time.; the resistivity observed when the reservoir is 100 pel. cent 'saturated with water, this fact would be interpreted as indicating a water saturation of 33 per cent if the saturation exponent were 1 and a water saturation of 6-1 per cent if the saturation exponent were 2.5. EXPERIMENTAL METHOD In the work to be described it was assumed that reservoir conditions are most nearly obtained when core plugs are desaturated by the capillary pressure technique referred to in numerous places in the literature, as for example. in Bruce and Welge's paper.' In this technique the core. saturated 100 per cent with brine, is placed in contact with a ceramic disc permeable to brine but not to the displacing medium for the displacement pressures used. Pres-ure is then applied to the displacing medium and brine forced out of the core through the ceramic disc. Fig. 1 shows the core plug in place in the cell in which resistivity and saturation measurements are made. Fig. 2 shows the schematic electrical diagram wed to make resistivity measurements on the core plug. A four-electrode type circuit is used, employing a Hewlett-Packard model 400A. AC vacnum tube voltmeter. The 60-cycle AC current througli the core is adjusted to 1 milliampere and measured by noting the voltage drop across the calibrated 100-ohm resistor. The vo1tages appearing at probes 1, 2, 3, and 4 are then successively measured. Voltage drops across the top, center, and bottom portions of the core are obtained by sublracting the voltages appearing at successive probes. This technique avoids any polarization or other high contact resistance phenomena which may develop at the current input electrodes. Resistances which may develop between the core and the probes, and which are small compared to the 1-megoam input impedance 01' the vacuum tube voltmeter will (obviously not affect the measurements allpreciably. Any very appreciable resistallces which may develop at any of the probe wires are detected and allowed for by inserting a 1-megohm resistor in series with the voltage measuring probe. If the probe resistance is actually zero, the new voltage measured after insertion of the I-megolim resistor will be approximately one-half of that previously measured. since the input impedance of the vacuum tube voltmeter is itself 1 megohm. If an! appreciable probe resistance has developed, the new voltage is found to be appreciably greater than one-half of the previously measured voltage. Such probe resistance; have been found to develop only occasionally and usually can be traced to poor connections betwern the core

Jan 1, 1949

By E. A. Steigerwald, G. L. Hanna

The influence of work-hardening exponent on the variation of fracture toughness with material thickness was studied for high-strength steel, aluminum, and titanium alloys. The results indicate that, when materials are compared at similar fracture toughness to yield strength ratios, the material with the lower work-hardening exponent undergoes the transition from flat to slant fracture at a larger thickness than material with a high work-hardening exponent. In the thickness range where complete slant fracture is obtained the reverse is true and a lower work-hardening exponent results in a lower fracture toughness. The influence of work-hardening exponent on fracture toughness is, therefore, dependent on the particular fracture mode. In the transition region a low work-hardening exponent is beneficial for fracture toughness while in the 100 pct slant region it is detrimental. THROUGH the use of fracture mechanics analyses, the influence of geometric variables on the crack propagation resistance of structures can be interpreted with reasonable consistency. However, in order to gain a more complete understanding of the fracture process, the influence of material parameters on crack propagation must be defined and coupled to the macroscopic fracture mechanics approach. The work-hardening exponent, which characterizes specific material behavior, may serve as an effective parameter to allow some degree of coupling to be accomplished. In the extension of a crack in a specimen of suitable dimensions the propagation process occurs in a stable manner when the crack extension force is balanced by the resistance to crack extension, which exists in the material at the crack tip. As the applied stress, and therefore the crack extension force, on the specimen increases, the resistance also increases primarily because the effective plastic zone at the crack tip, which is the main energy absorption process, becomes larger. Since the work-hardening rate of a material influences the stress-strain relationship, it will also influence the energy absorption process in the plastic enclave at the crack tip and hence should have an effect on crack propagation. A number of studies have been made correlating the strain-hardening exponent or the strain to tensile instability with the ability of a material to resist fracture. Gensamer1 concluded that a low-strain-hardening exponent would result in a steep strain gradient at the base of a notch. He reasoned that a large work-hardening coefficient would result in high-energy ab- sorption due to the increased area under the stress-strain curve. Larson and Nunes2 experimentally observed in Charpy tests on steels heat-treated to below 200,000 psi yield strength that the energy to failure in the fibrous mode, i.e., above the brittle-to-ductile transition temperature, was logarithmically related to the strain-hardening exponent. In order to avoid the complicating effects present in studying materials which undergo a brittle-to-ductile transition, Ripling evaluated the notch sensitivity of a variety of fcc metals with varying work-hardening exponents.3 The results indicated that the relative notch sensitivity, as determined from tests on specimens with a sharp notch, decreased with increasing values of strain hardening. Although the energy required for ductile or fibrous fracture increases with increasing work hardening, high-strength steels often exhibit improved crack propagation resistance when heat-treated to obtain low values of strain hardening.4,5 An analysis of whether low strain hardening is beneficial or detrimental to crack propagation resistance must depend on the particular fracture criterion involved. At temperatures where the material is relatively ductile and the development of a critical strain is required for fracture, high strain hardening increases the energy required to produce failure. In the transition region and below, however, a critical stress law appears to be valid6 and a low rate of work hardening may produce superior resistance to semibrittle crack propagation. The experimental program is aimed at studying these possibilities and determining the specific influence of strain hardening on the crack propagation resistance of several high-strength materials. MATERIALS AND PROCEDURE The alloys, chosen as representative of various classes of high-strength materials, are summarized in Table I. The heat treatments evaluated along with the smooth tensile properties are presented in Table 11. Pin-loaded sheet tensile specimens were employed to determine the smooth tensile properties. A strain gage extensometer (measuring range 0.200 in.) was used at a strain rate of 0.02 in. per in. per min. The work-hardening exponents were determined from the stress-strain curves generated in the smooth tensile tests and the assumption that the portion of the stress-strain curve beyond the yield point can be described by the power relationship: where a is the true stress, P is the true plastic strain,

Jan 1, 1969

By W. T. Roberts, N. G. Turner

A study of the fatigue properties of several grades of commercially pure titanium has established that the strain-aging process is of minor importance in the development of a fatigue limit and a relatively high fatigue strength ratio. Metallographic observations and damping measurements at room temperature indicate that striations are able to spread from grain to grain only at stress levels above the fatigue limit. This suggests that the fatigue limit represents the stress above which large-scale dislocation unlocking takes place. Fatigue tests on annealed material at - 60" and - 196" c showed that under conditions when a thermally activated diffusion process would be suppressed the fatigue limit is not eliminated. Prestraining at room temperature did not have a detrimental effect on fatigue strength at room temperature but a decrease was recorded at — 60°C. This is further evidence that initial dislocation locking is a important strengthening mechanism. TITANIUM and titanium alloys have S-N curves with a definite fatigue limit, and a high ratio of fatigue limit to UTS can be attained. Other materials which show similar fatigue characteristics are mild steel and some Al-Mg alloys. The fatigue limit of these materials has been associated with their strain-aging capacity. It is well-known that commercial-purity titanium contains interstitial impurities which can give rise to a sharp yield point, and a small strain-aging effect following static strain has been demonstrated.7 This type of aging reaction is differentiated from the dynamic aging process when aging occurs during plastic deformation, and which is generally observed at elevated temperatures. In a titanium at room temperature, dislocation locking is associated with the interaction of interstitial oxygen, nitrogen, and carbon atoms with dislocations. Ehr-lich has shown that the distortion produced by introduction of these atoms into the hcp lattice has no shear stress component and hence there is no interaction between the stress field and the screw component of a dislocation. Thus the dislocations as a whole are only weakly locked. It is clear that strain-aging effects in hcp a titanium will be much less pronounced than those observed in bcc iron and steel. In recent years, the attribution of the fatigue limit solely to strain aging has been questioned. It has been pointed out that a definite fatigue limit is observed at temperatures as low as -196°C in some titanium alloys,' and strain aging is not expected to be effective at this temperature. The role of initial locking of dislocations in determining fatigue behavior has been examined in low-carbon steel by Oates and Wilson. They showed that under conditions in which the aging potential is low the factors which control the buildup of local stresses and hence affect dislocation unlocking, e.g., grain size, are important. There are indications that other metals can have a definite fatigue limit with no established strain-aging capacity, an example being magnesium12 which has the same crystal structure as a titanium. The spread of plasticity from grain to grain in hexagonal metals may be more difficult than in cubic metals because of the limited number of slip systems in the former, and this may account in part for their fatigue behavior. The present work was undertaken to elucidate the relative importance of crystal structure, strain aging, and initial dislocation locking in determining the properties of commercially pure titanium when subjected to cyclic stressing. 1) EXPERIMENTAL METHODS Three grades of commercial-purity titanium were used and a material of lower interstitial content was prepared by melting high-purity Japanese sponge titanium (referred to as H.P. Ti). The compositions and typical mechanical properties of the materials are shown in Table I. Fatigue tests were made in push-pull (zero mean stress) using an Amsler Vibraphore machine at a frequency of about 160 cps. Two types of fatigue specimen were used—one with a waisted gage length for determination of S-N curves and the other with a parallel gage length for metallographic studies and damping measurements. After careful machining and mechanical polishing, all specimens were electropolished prior to fatigue testing. The electrolyte consisted of 10 parts methyl alcohol, 6 parts 2-butoxyethanol, and 1 part perchloric acid (SG 1.54) and it was maintained at a temperature of -10" to -20°C during polishing. Tests at room temperature were normally carried out with the specimen immersed in a silicone oil bath which could be heated for elevated-temperature tests.

Jan 1, 1969

By J. D. Mote, J. E. Dorn

This investigation was undertaken to study the effects of piledup arrays of dislocations on inducing slip, twinning, and fracturing in magnesium bicrystals. A series of variously oriented bicrystals of magnesium having a vertical grain boundary were prepared and tested in tension. It was found that piled-up arrays of dislocations at the grain boundary could, under appropriate conditions, induce slip, twinning- and cracking. The results that were obtained substantiate, at least qualitatively, the general dislocation mechanism for transmission of strain across grain boundaries and the Petch-Stroh concept of fracturing. WHEREAS single crystals of magnesium generally exhibit extensive deformation, coarse-grained poly-crystalline magnesium at subatmospheric temperatures fractures after a few percent elongation.' Although a small amount of ductility is obtained, several features of this fracturing are characteristic of typical brittle behavior. Over a rather broad temperature range the fracture stress is insensitive to the test temperature and the fracture stress increases linearly with the reciprocal of the square root of the mean grain diameter. The course of fracturing is predominantly intergranular, but small fragments of adjacent grains frequently adhere to the fractured surface.2 The brittle behavior of polycrystalline magnesium is attributable to the limited number of facile deformation mechanisms it exhibits at low temperatures. For a general deformation of a randomly oriented polycrystalline aggregate, each grain must exhibit at least five independent mechanisms of deformation to permit accommodation of the imposed deformation from grain to grain.= Although minor amounts of prismatic slip occur in corners of grains where stress concentrations are known to be high, glide in polycrystalline magnesium at low temperatures takes place almost exclusively by basal slip.' The common type of twinning, which takes place on the (1012) pyramidal planes, can under the most favorable orientations, lead to a. strain of only 6.9 pet; the contribution of twinning to the tensile strain would indeed be much less than this in a randomly oriented polycrystalline aggregate of magnesium. Since the three mechanisms of basal slip are coplanar, they are equivalent to only two independent mechanisms, a number insufficient for a general deformation. Consequently, once the permissible twinning has taken place in conjunction with basal slip, no further plastic deformation is possible because of interference to slip at the boundaries of dissimilarly oriented grains. At this stage brittle fracturing takes place due to high stress concentrations at the juncture of slip bands with the grain boundaries; the predominance of intergranular fracturing in magnesium, in preference to transcrystalline fracturing which is prevalent in zinc, has not yet been rationalized. A more atomistic description of the plastic behavior and fracture characteristics of magnesium follows from the analyses made by stroh4 on the stresses induced by piledup arrays of dislocations. Slip first takes place by dislocation motion in the most favorably oriented grains. As the dislocations approach the boundary of a dissimilarly oriented adjacent grain they begin to form an array of dislocations with its attendant stress field. Piledup arrays of screw and edge dislocations introduce high localized shear stresses at the spur of the array; piledup arrays of edge dislocations also induce high tensile stresses localized in the vicinity of the grain boundary. Whereas the shear stresses can induce slip to take place, the tensile stresses, if sufficiently high, can cause fracturing. The localized shear stress will be relieved if sufficient numbers of mechanisms of deformation become operative in the original and the adjacent grain to permit accommodation of the dislocations in the grain boundary. In this event a ductile behavior will be obtained. But if the number of deformation mechanisms is insufficient for complete migration of dislocation arrays into the grain boundary, the tensile stresses due to the edge components of piledup dislocation arrays will continue to increase with increasing applied stress until fracturing takes place. Whereas face-centered-cubic metals have a sufficient number of mechanisms of slip for accommodation of dislocations in their grain boundaries to exhibit ductile behavior, hexagonal-close-packed metals, in general, do not. Consequently, hexagonal-close-packed metals are usually brittle except when conditions such as alloying or temperature permit facile slip by a number of mechanisms. The arguments presented above suggest that the mechanical behavior of magnesium depends on whether or not dislocation arrays in adjacent grains can enter the grain boundary. When such accommodation is possible, ductile behavior is expected; but when such accommodation is impossible, fracturing will ensue. To further test the validity of these arguments it was considered advisable to study the

Jan 1, 1961

By S. A. Tims

INTRODUCTION The Falconbridge mine ore body extends about 1.6 km (1 mile) in length and the deepest developed ore is on the 6050 level below surface. The ore zone varies in width from a few inches to over 30 m (100 ft) and the average width is 4.9 m (16 ft). Access levels are driven in the ore at 53.3-m (175-ft) intervals. The principal method of mining is overhand longitudinal cut-¬and-fill. Prior to 1962 timber square-set stoping as a secondary extraction method was used for about 15% of the total production. Undercut-and-fill was intro¬duced at Falconbridge in 1962 as a potential replace¬ment for the square-set method in heavy ground. The undercut-and-fill method was developed by Inco in the 1950s, its principal application being to transverse pillar mining. Falconbridge made modifications to this method. A feature of the mine is the No. 1 flat fault which dips 0.79 rad (45°) towards the northeast. The main characteristic of the fault is the presence of large swells of ore directly under the plane of the fault. The ground under the fault area is highly fractured and associated with massive sulfides. In the past, the ore under the fault was recovered, with difficulty, by either tight cut¬and-fill or square-set stoping. In the 1970s these meth¬ods were supplanted to a large degree by the under-cut-¬and-fill method. An advantage of the current undercut-and-fill method which uses cemented fill compared to the cut-and-fill and square-set methods is the reduction of dilution due to better control of the walls. At Falconbridge mine, it is estimated that the grade of ore produced by undercut¬and-fill is improved by approximately 10% over other methods. Where undercut-and-fill is used in very weak ground, a much greater improvement in grade can be expected. Table I shows mining production for 1974. The undercut-and-fill method was first used at Falconbridge during 1962. The first longitudinal stope was prepared for undercutting by laying down laminated beams the length of the stope and installing a lagging mat floor on top of the beams. Unconsolidated tailings fill was poured on top of the mat floor. As the cut ad¬vanced under the floor, heavy posts were placed under the laminated beams at 1.8-m (6-ft) intervals. During 1966, a radical change was made to the method when tailings fill, consolidated with portland cement, replaced the unconsolidated fill. This development eliminated the laminated beams and heavy mat floor and greatly im¬proved the stability of the stope. This system, with minor variations, is currently used at Falconbridge mine. APPLICATION The undercut-and-fill method is used to mine in¬competent ground, sills or floor pillars under mined-out levels, or a block of ore isolated between levels. It is occasionally used to advantage in sequencing produc¬tion from various mining blocks. This is done by mining a block of ore cut-and-fill method and at the same time mining the ore block directly underneath by the under¬cut-and-fill method. The undercut-and-fill mill holes at Falconbridge are either boreholes, stripped timbered raises, or steel mill holes. Boreholes and rock raises tend to slough in heavy and broken ground which increases dilution when sloughing exceeds the ore width outline and also in¬creases the difficulty of moving down to start the new cut. For example, in one installation, a 1.2-m (4-ft) diam borehole sloughed to a size of 3.7 x 5.5 m (12 x 18 ft). The undercut-and-fill method usually requires a mill hole extending from the level below the ore to the top horizon of the ore block. The customary methods of providing a mill hole are: 1) A borehole is driven from level to level through the ore block and a chute installed on the bottom level (Fig. 1). 2) An existing raise is used as a mill hole. If the raise is timbered, a steel mill hole is installed inside the timber and tailings fill poured around the steel mill hole (Fig. 1). 3) An existing steel mill hole, situated at one end of a mined-out stope, is used as the mill hole for an ad¬jacent undercut-and-fill ore block. The mill hole posi¬tion is determined when planning the mining sequence of the first stope (Fig. 2).

Jan 1, 1982

By G. L. F. Powell

g samples of Cu-20 wt pct Ag alloy have been mdercooled to a maximum of 197°C by melting under a slag of commercial soda-lime glass in a vitreous silica crucible. No grain refinement of the primary copper was observed in samples undercooled to the maximum of 197°C. When the samples contained a small amount of oxygen, the copper dendrites were partially recrystallized at undercoolings greater than 97°C. In previous papers'-3 reporting the grain structure of undercooled silver and copper, it was observed that grain refinement was dependent on both undercooling and oxygen content. Grain refinement occurred in undercooled silver when the degree of undercooling exceeded the range 153" to 175"C, while in Ag-0 alloys (0.12 wt pct) fine equiaxed grains were exhibited when undercooling was greater than 50°C. Similarly, copper samples undercooled as much as 208°C displayed fan-shaped growth from a single nucleation site, while the grain structure of Cu-O alloys (0.08 wt pct) was fine and equiaxed at undercoolings larger than 150°C. Thus the presence of oxygen greatly reduced the undercooling at which grain refinement occurred. It was also observed that the change in grain size resulted from recrystallization and was not due to an enhanced nucleation rate in the liquid-solid transformation. It is possible that the influence of oxygen on recrystallization is due primarily to its presence as a solute element. walker4,' reported that, although a grain size change did not occur in pure nickel until the undercooling exceeded 150°C, small grains were observed in samples of Ni-Cu alloy solidified at small and large degrees of undercooling. Jackson et al.6 suggested that the fine grained structure of the Ni-Cu alloy resulted from the melting off of dendrite arms during recalescence. This remelting process may occur in alloys as a result of segregation during freezing which causes a variation in liquidus temperature from point to point within a dendrite. It was therefore decided to undercool copper with a metallic alloying element to ascertain whether the presence of a metallic solute would have a similar effect to oxygen in inducing grain refinement. A Cu-Ag alloy was chosen, since both metals had been shown to behave similarly on undercooling. The alloy Cu-20 wt pct Ag was selected since the eutectic constituent outlines the initial growth form of the primary copper, so that the as-frozen grain structure is not obscured if subsequent recrystallization occurs. This paper describes the results of undercooling experiments carried out with Cu-20 pct Ag samples undercooled to a maximum of 197°C and the effect of oxygen content on the grain structure of the undercooled samples. EXPERIMENTAL Melting was carried out in a small cylindrical resistance furnace using "fine" silver granulate and oxygen-free high conductivity copper. The procedure adopted was to melt the required quantity of silver in air in a clean vitreous silica crucible for approximately 15 min, freeze, and add granulated commercial soda-lime glass to form a complete surface slag cover, after which the sample was melted and frozen several times to reduce the oxygen content. The glass slag cover was approximately 3 in. thick. Pieces of copper (=50 g) were added to the crucible until the required quantity to make 350-g samples of alloy had been charged. Each piece was added quickly to the crucible which was held at a temperature slightly above the melting point of silver. The piece was quickly pushed beneath the glass to minimize oxidation and any oxide coating usually decomposed before the piece had settled down into the silver. After the full quantity of copper had been added, the melt was stirred with a silica rod to hasten homogenization and a Pt/Pt 13 pct Rh thermocouple enclosed in a vitreous silica sheath inserted for temperature measurement. Heating and cooling curves were recorded on a potentiometric chart recorder fitted with a zero suppression unit. The milli-voltage range of the recorder was adjusted so that temperatures could be read to 1°C. Heating and cooling curves were taken every hour until three consecutive readings gave the same solidus-liquidus range, consistent with the solidus-liquidus range for this alloy composition by reference to Hansen and Anderko.7 Metallographic examination of samples frozen at this stage, failed to show any variation in composition from bottom to top of the ingot. Consequently, it was considered that the melt was homogeneous at this stage and undercooling experiments were then car-

Jan 1, 1970

By D. Turnbull, J. H. Hollomon, J. C. Fisher

Application of the concepts of nu-cleation and growth to the analysis of experimental transformation data has led to valuable descriptions of phase transformations, an outstanding example being the transformation austenite —* pearlite which has been examined with particular care by Mehl and co-workers.&apos;-5 In addition to the pearlite transformation, the proeutectoid fer-rite and proeutectoid carbide transformations are known to proceed by nucleation and growth. Martensite, on the contrary, until recently was thought to form by a mechanism involving neither nucleation nor growth; however, extension of standard nucleation theory6 suggests that martensite, bain-ite, and the other products of austenite decomposition all grow from nuclei in the parent phase. The theory that martensite forms by nucleation and growth is strongly supported by recent experimental work of Kurdjumov and Maksimova.7 The concepts of nucleatioli and growth have been fruitful also in providing a sound basis for quantitative theoretical treatments of the kinetics of phase transformations. For example, Volmer and Weber8 and Becker and Döring9 developed the theory of nucleation from fundamental considerations to a point where excellent agreement was obtained with the results of experiments on the condensation of supercooled vapors. As a result of their analysis, the kinetics of vapor-liquid transformations now can be predicted. It seems probable that application of the theories of nucleation and growth to a quantitative study of austenite decomposition similarly will clarify the nature of the individual transfor: mations involved, and will enable the calculation of austenite transformation kinetics. In the present paper, the theories of nucleation and growth are applied to the austenite ? martensite transformation in steels. The analysis begins with a discussion of nucleation in single component systems. Martensite appears to be coherent with the parent austenite, hence the nucleation theory is modified to include the effects of elastic distortion. Nucleation in the two component iron-carbon system then is discussed, for most steels are primarily alloys of these two elements. Finally, M. temperatures and martensite transformation curves are calculated for each of several alloy steels of varying carbon and chromium content, and are compared with those determined experimentally by Lyman and Troiano10 and Harris and Cohen.11 Nucleation Theory NUCLEATION IN SINGLE COMPONENT SYSTEMS6,12-14 The work required for reversible formation of a region of phase within the parent a phase is expressed conveniently as the sum of two terms: W1 = Aa, the product of the area of the interface and the interfacial free energy, and W2 = VAf, the product of the volume of the region and the free energy increase per unit volume associated with the transformation. The total work is therefore W = Aa + VAf. When a is more stable than ß, Af is positive and W increases without limit as the volume increases. The transformation a ?ß does not occur. It is nevertheless true that small regions of phase ß enjoy temporary existence here and there in the a. The equilibrium number of ß regions of given size is proportional to exp(— W/kT) per unit volume of a, assuring that larger (ß regions occur with diminishing probability. When a is less stable than ß, Af is negative and W passes through a maximum as V increases. Assuming for simplicity that regions of ß are spherical, as is true when the interfacial tension is isotropic and there are no elastic strains, W = 4r2a + (4/3)*r3Af The maximum value of W is W* = 16iro3/3Af2 [1] for regions with radius r* = -2o/Af. [2] For single component condensed systems it has been shown14 that the steady rate of nucleation of 0 per unit volume of untransformed a is nearly proportional to exp[- (W* + Q)/kT] where Q is the activation energy for the unit processes of adding or removing one atom from an embryo or nucleus. If To is the temperature at which a and ß are in equilibrium, the rate of nucleation is a maximum at a temperature 0 < T < To where (W* + Q)/kT is a minimum. P regions smaller than critical size are called embryos; they tend to grow smaller and disappear, only exceptionally growing larger. Regions equal to or larger than critical size are called nuclei. A critical size nucleus may grow indefinitely large or may shrink back to a, either process decreasing the free energy of the region.

Jan 1, 1950

By F. B. Foley

IT is with an unusual degree of personal satisfaction that I find myself in a position to pay tribute to the memory of Henry Marion Howe. One could not have spent any length of time in the presence of Dr. Howe without profiting intellectually. I do not hesitate to say that my years of association with him were the most stimulating of all my years of metallurgical study. He always impressed one with his own eager search for knowledge. Never dependent on the written word alone he sought information from anyone whose opinion he valued. His ability to piece together bits of apparently conflicting data from various sources so as to build up a logical hypothesis was unique. A small slight man with the intellect of genius he would have gone to the top in any endeavor he undertook and it was fortunate for metallurgy that its study attracted him as it did. Howe was a modest man. I like to recall an incident which left a lasting impression with me. The lab- oratory in his home, "Green Peace," was in the basement and access was by way of stairs leading down from his secretary&apos;s room. In using these stairs my attention was attracted many times to an ordinary cardboard shoe box which reposed on the shelf above the landing. It was crudely labeled on its side in black ink "Vanity Box." My curiosity was aroused to the point that I finally asked his secretary what it was. With some amusement she took the box from its shelf on the stairway, opened it and showed me its contents—numerous letters, from the foremost men of science of every civilized country throughout the world, commending his "Metallography of Steel and Cast Iron." I recall that in reply to one who thought there was not enough of Howe&apos;s own researches in his book he wrote, "Primarily I am a writer, secondarily an investigator." Howe wrote to make his readers think. No one ever strove harder than he to be right but above all, whether his viewpoint proved ultimately to be right or wrong, he was always content if by his stand, he provoked a reader to take the next step along the path to greater knowledge. I doubt that he was ever afraid to be wrong for he was always secure in the thought that his effort was guided by a sincere search for the truth. One continually searching for truth is entitled to occasional excursions up the wrong alley. A glance backward to the metallurgical confusion of some thirty to forty years ago, or need one go back so far, provides convincing proof of what a host of companions one may have in a common acceptance of ideas which the future will prove to be wholly untenable. Well over a hundred years have passed since investigators have interested themselves in the effect of increasing the temperature of iron and steel on their mechanical properties. We are told by Charles Walrandl in "Industrial Annals" for June 11, 1822, that bend tests, conducted in a Russian steel works of Prince Demidoff, on steel bars "highly heated" and bent during cooling became brittle when bent at an iris blue color. He concluded, "That when steel is heated to a temperature between 473°F and 662°F the mettle was more brittle between these limits than at a much lower or at a much higher temperature." It was a curious bit of information recognized as true to this day and still not explained satisfactorily. In 1878 Charles Houston in Annales de Mines associated this brittleness with an increase in tensile strength at 572°F. When this relatively low temperature is exceeded it is recognized that steel becomes weaker as temperature is increased up to the melting point, where no strength of practical importance remains. It is easy to believe, in fact it goes without saying, that this weakening as the temperature of a metal is increased is the result of the motion of the atoms making up the metal, a motion which itself is evidence of the temperature increase. However, if we are considering iron or steel we find that this decrease in strength is not a steady one, for, besides the increase in strength just referred to, one comes to a temperature, the critical temperature, where results of tests indicate the metal to be extremely weak and then as temperature increases to become sensibly stronger again. This apparent anomaly was made the subject of the first Howe Memorial Lecture, delivered by Albert Sauveur in 1924. It may be of interest to review these findings of Sauveur. He used two methods of investigation. One involved the twisting of bars. The bars were heated in an

Jan 1, 1951

By Chester A. Rowland, David M. Kjos

INTRODUCTION Mineral ore comminution is generally a feed preparation step for subsequent processing stages. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding - primary and secondary), natural or manufactured nonmetallic media (pebble milling) or manufactured metallic media - steel rods, steel or iron balls, or a combination of autogenous media and steel balls (SAG milling). This chapter covers rod and ball mills utilizing manufactured metallic grinding media. MILL DESIGN The interior surface of rod and ball mills exposed to pulp and/or grinding media are protected from wear and corrosion by rubber, metallic or a combination of rubber and metallic wear resistant materials. Rod and ball mills essentially draw constant power, thus are well suited for use of synchronous motors with power factor correction capabilities as drive motors. A net of approximately 120 to 130 percent of running torque is required to cascade the charge in these mills. The pull-in torque is about 130 to 140 percent with the pullout torque to keep the motor in-step (in-phase) generally in excess of 150 percent. When rod and ball mill are started across-the-line the starting and pull-in torques result in inrush currents exceeding 600 percent which possibly result in high voltage drops. To deliver 130 percent starting torque to the mill the motor design must take into account the maximum anticipated voltage drop. Motor torque decreases as the decimal fraction of the voltage available squared. E.g., a motor rated 160% starting torque with a 10% system voltage drop will deliver 160% x or 129.6% torque to its output shaft When it is not possible or practical to start a fully loaded synchronous motor across-the-line it is possible to utilize the motor&apos;s pull- out torque to start the mill. By using a clutch, normally an air clutch. between the motor and the mill, the motor is brought up to synchronous speed before the clutch is energized. If the motor has an adequate amount (175 or greater) of pull-out torque the pull-out torque starts the mill without major disruptions on the electrical system. Since the energy release at initial cascade of the mill charge is an inverse function of acceleration time, a minimum acceleration time of 6 to 10 seconds or more is recommended to prevent damage to the mill or the mill foundation. Economics at the time of plant design and mill purchase determine the drive to be used. The simpliest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinionshaft by either an air clutch or flexible coupling. Using a speed reducer between the motor and pinionshaft permits using motors having speeds in the range of 600 to 1000 RPM. In this speed range, if power factor correction is not required induction motors can be used; squirrel cage where there is no restriction on inrush current; slip ring where a slow start and low inrush current is required. Air clutches can also be used to ease starting problems with squirrel cage motors. In some areas of the world induction motors and starters are less expensive than synchronous motors at a sacrifice of motor efficiency and power factor correction. Dual drives, that is two pinions driving one gear mounted on the mill, become economical for ball mills drawing more than 3500 to 4000 horsepower (2600 to 3000 kilowatts). Further developments of the low frequency, low speed synchronous motors with the rotor mounted on the mill shell or an extension of one of the mill trunnions could improve the cost picture for these "gearless drives", making them practical for large ball mills. The percent of critical speed, which is the speed at which the centrifugal force is sufficiently large to cause a small particle to ad- here to the shell liners for the full revolution of the mill is given in mill specifications. Critical speed is determined from the following: Where D is mill diameter inside liners (specified in meters). Cs is critical speed in RPM. When D is specified in feet

Jan 1, 1998

By Lee Hillard Meltzer, Ralph E. Davis

INTRODUCTION During the past few years emphasis has been placed upon methods of estimating the future expectancy of gas production from natural gas fields. Before technical methods were applied, the production expectancy over future years was based upon the knowledge of gas well behavior, learned through long experience and embedded in the "know-how" of men long in the gas producing business. It is doubtful that a technical study of future expectancy of a gas field or a group of fields was ever prepared for the preliminary planning of a natural gas pipe line system built prior to about five years ago. The decline in well production capacity was naturally recognized by all familiar with the business since its earliest beginnings more than 75 years ago. In 1953, the Bureau of Mines published Monograph Number 7, "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices," which gave to the industry the first technical analysis of the decline in production of individual gas wells. This method affords a means of estimating the future production in relation to decline in reservoir pressure. The demand for technical determination of expectancy of future gas productivity from fields or a group of fields led technical men to the application of the knowledge of well behavior to the problems. The decline in a well&apos;s ability to produce as pressures declined could be estimated by the use of the curve known as the "back-pressure potential curve" as developed by the Bureau of Mines. A field containing few, or even numerous, wells could be analyzed on the basis of the sum of potentials of all wells. In most studies of this nature, the problem is to estimate the rate of production that can be expected, not only from present wells but also, from wells that will in the future have to be drilled into the reservoir being studied. The "back-pressure potential" method requires that the following data be known or estimated: (1) Proved gas reserves. (2) Current shut-in pressures and rate at which shut-in pressures change with production. (3) Back pressure potential data on wells in the source of supply. (4) Ultimate number of wells which will supply gas, and their potential. (5) Limitations on productivity such as line pressures against which the wells will produce, friction drop in the producing string, and so forth. It is evident that the resulting estimate of gas available in each year for a future of say, 20 years, contains many uncertainties. While the method may have considerable merit for a field that is fully developed, it cannot be completely dependable in fields that are only partially developed. In such cases, some of the data upon which it is based can only be estimated or assumed. In the study of this problem during the past few years, a method has been developed which we believe has great merit, especially when applied to fields subject to substantial future drilling, and when applied to the study of fields which, on the average, appear to have characteristics similar, in general, to the average of the fields used in the development of the "yardstick" outlined herein. From an analysis of the production history of 49 reservoirs which are depleted, or nearly depleted, a curve has been constructed which shows the average performance of the reservoirs during the declining stages of production. When properly applied, this "average performance curve" can be used to determine the stage of depletion at which a reservoir or group of reservoirs will no longer be able to yield a given percentage of the original reserves. "AVAILABILITY" AND "AVAILABILITY STUDIES" The rate at which. a reservoir will yield its gas depends basically upon physical factors, such as the thickness and permeability of the sand, the effect of water drive, if any, and other conditions, and upon economic factors, such as the number of wells drilled. Within the ranges set by the physical conditions, a rate of delivery tends finally to become established. The rate (or range of rates) represents a balance between the interests of the operator, who desires the maximum return from his property and of the pipe line owner, who desires to maintain a firm supply for his market. This balance, which is influenced by the terms of the contract, determines the capacity which will be developed by the operator, and the time and rate at which the decline in production is permitted to occur. Thus the "availability" of gas

Jan 1, 1953

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter (LID) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23% of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with LID ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests, a radial prestress of 3000 or 5000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3000 psi prestress, was 54.3% for limestone, 40.3% for marble, 44.7% for sandstone, and 23.4% for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5000 psi prestress, was 74.2% for limestone, 51.2% for marble, 61.6% for sandstone, and 29.7% for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room-and-pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent. One important objective of the U.S. Bureau of Mines (USBM) mining research program is the rational design of mining systems. In the design of room-and-pillar mining operations, pillar strength is a fundamental variable. It is customary to estimate this strength from uniaxial compression tests of rock samples and to correct this value for the length-to-diameter (LID) ratio of the in-situ pillar. This method of estimating pillar strength corrects for pillar shape but does not consider the effect of a large horizontal in-situ stress field that sometimes exists in underground formations. The purpose of the work covered in this report was to determine to what extent the compressive strengths of model pillars of relatively brittle rock loaded in axial compression were affected by lateral end constraint. In previous work, Obert l used solid steel rings bonded to the ends of dogbone-shaped specimens to study the creep behavior of three quasi-plastic rocks -salt, trona, and potash ore - during a test period of 1000 hr. These rings provided radial constraint during the loading cycle of 20 to 50% of the axial stress for specimens with LID ratios of 2, 0.5, and 0.25. He concluded that (1) "for a quasi-plastic material the end constraint strongly affects the specimen strength, and (2) as D/L increases (length-to-diameter decreases), the specimens lose their brittle characteristics and tend to flow rather than fracture." He also concluded that model pillars constrained by rings were better for use in predicting the strength of mine pillars than either cylindrical or prismatic specimens. This conclusion appears to be valid where mine pillars, roof, and floor are a single structural element. In the present study, 460 specimens of four relatively brittle rocks — limestone, marble, sandstone, and granite - were tested to failure. The study consisted of two parts: (1) the effect on the compressive strength of end constraint produced during the axial loading cycle by solid steel rings bonded with epoxy to the ends of the specimens, and (2) the effect on the compressive strength of increased end constraint produced in part by a prestress applied prior to axial loading and in part by lateral expansion of the specimen during the loading cycle. The first part of this study was reported in some detail earlier.2 EXPERIMENTAL PROCEDURE AND EQUIPMENT Model rock pillars of the sizes and shapes shown in Fig. 1 were broken in axial compression when the ends were constrained as shown in Fig. 2. he straight specimens were broken without ring constraint. The specimens of dogbone shape were broken with (1) solid

Jan 1, 1970

By E. P. Pfleider, Rolland L. Blake

IT is generally believed that the amount of diamond drilling will increase appreciably in the next decade, as the seaarch for minerals throughout the world becomes more difficult and intense. An attendant problem may be one of short diamond supply, resulting in higher bit and drilling cost. With this background, the U. S. Bureau of Mines&apos; and the School of Mines at the University of Minnesota&apos; have established comprehensive research programs in diamond drilling. One of the several aims is the design of a more efficient bit, which would lower diamond consumption and increase rate of advance, both essential in reducing drilling costs. The objective of the specific research problem" discussed in this paper was an investigation of the cutting action of the cliamonds set in a diamond drill bit, cutting action meaning the manner in which the diamonds cut or. loosen the minerals in the rocks being drilled. In the literature on cutting action such descriptive terms are used .as: grinding, wearing, cutting, breaking, shearing, scraping, melting, and chipping. These actions were seldom described or defined. Grodzinski describes the cutting action of a single diamond in the shaping of certain types of material as "breaking out chips of the material." Brittle mate-. rials break as small separate chips, and tough materials, because of heat generated, give a continuous chip. Deeby said about diamond drills: "When diamonds are forced into the formation and rotated, they either break the bond holding the rock particles together, or they cause conchoidal fracture of the rock itself. The former action occurs when drilling in sandstones, siltstones, shales, etc. and the latter action when drilling in chert, flint, or quartz." He said that diamonds cut on the "grinding principle" but he does not define or elaborate on this action. The cutting action of diamonds on glass was first investigated about 1816 by Dr. W. H. Wol-laston, an English physicist. The best glass-cutting diamonds have a natural or artificially rounded cutting edge. This edge first indents the glass and then slightly separates the particles, forming a shallow and nearly invisible fissure. Since none of the material is removed, this action is one of splitting rather than cutting. No other reports of research work on the cutting action of the diamond were found, and further work was considered justified and advisable. It is impractical, even if possible, to observe directly the cutting action of a diamond drill bit in rock; therefore it was necessary to devise an indirect method. It was believed that a study of the following three observations would lead to a better understanding of the cutting action: 1—the appearance of the minerals or rock surface in the bottom of the hole, 2—the size, shape, and other characteristics of the drill cuttings, and 3—the condition of the diamonds in the bit. The cutting action in a particular rock probably varies with bit pressure and speed. If the bit were slowly lifted off the rock, the effect of decreasing pressure might obliterate those bottom hole characteristics that are specific at the test pressure. Likewise, if the drill were stopped with the bit still in contact with the bottom of the hole, then decreasing speed effects would tend to obliterate the characteristics at the set test conditions. Therefore, in order to preserve those cutting effects impressed on the rock at test conditions, it seemed necessary to lift the bit off the bottom of the hole almost instantaneously once drilling conditions, i.e., revolutions per minute, pressure, and water flow became constant. In addition to observing the cuttings, the bit, and the bottom of hole, it seemed desirable to collect some quantitative data for purposes of correlation with the observations and for a record of bit performance. Consequently such data as revolutions per minute, force applied, and rate of advance of the bit were recorded. Six rock types, listed in Table I, were chosen for the tests. It was felt that these rocks had most of the variable characteristics of texture, bonding, and mineral hardness met in the common rocks generally being drilled. The sandstone was so poorly cemented as to be friable, even though most of the cement was silica. The limestone, though well cemented, was quite porous. Originally it was planned to conduct the tesk work with a full-scale drill unit, using EX bits, 7/8-in. core, 11/4-in. OD. The drill worked well, but was too cumbersome for rapid, accurate drilling of many short holes (1 ½-in.) in varied rock types. A new

Jan 1, 1954

By Charles H. Grant

Some of the limiting factors relative to explosive crushing of rock and ways to overcome a few of these problems are presented. Relationships between borehole diameters, bench heights, and spacings, along with a review of the influence geometry has on energy as these are changed, are discussed. Efficiency in use of explosives and the decay of energy as it moves through rock and is absorbed and dissipated, is described, along with fragmentation as a function of spacings and energy zoning, etc. Communications are one of the major problems encountered. In an effort to provide a better understanding of the use of explosives, it is necessary to take a little different view of what explosives are, how to look at them as tools to fragment rock, and some of the problems encountered in doing so. First, take the explosive: although there are many factors involved, consider these as being reduced to only two — shock-strain imparted to the rock by the high early development of energy, and the gas effect which is a combination of heat, moles of gas formed, rate of formation of these gases which develop pressures, etc. First, consider shock energy by itself and assume there is no gas effect in the reaction. Fig. 1 illustrates a block or cube of rock, in the center of which is detonated an explosive charge which is 100% shock energy. Tensile slabbing would be seen on the surface and probably the cube of rock would generally hang together even though microcracks were formed. If the situation is reversed and an explosive whch has no shock energy and only gas effect (Fig. 2) is considered, the cube of rock would act as a pressure vessel and contain the pressure from the gas effect until it exceeded the rock-vessel strength; then the rock would break in a few large pieces. If these two kinds of energy are put together and the area of shock-strain around the explosive (Fig. 3) is considered, the two energies will be seen working together to furnish broken rock. The gas effect applies pressure to the microcracks formed from the shock energy to weaken the rock-pressure vessel and propagate these cracks to break the rock apart. It not only will be broken more finely, but will break apart at a lower pressure than the gaseffect case, since the shock energy has first weakened the rock vessel. Although tensile spalling from the shock-strain imparts momentum to the rock, the main source of displacement comes from the gas effect. The term "rock" is being used to mean any material to be blasted. These energies are absorbed by the rock in different ways. First, classify rock into two main categories: "elastic" and "plastic-acting." Elastic rock should be thought of as rock which can transmit a shock wave and is high in compressive strength, such as granite or quartzite. Since this elastic rock transmits a shock wave well, it makes good use of the shock energy from the explosive-forming cracks, etc., for the gas effect to work on. Plastic-acting rocks are rock masses which are relatively low in compressive strength and absorb shock energy at a much faster rate, thereby making poor use of the shock energy by not developing as extensive a cracked zone for the gas effect to work on. Rocks of this type are generally softer materials such as some limestones, sandstones, and porphyries. For the most part, the shockenergy part of the explosive reaction is wasted in plastic-acting rock, leaving most of the work to the gas effect. Since the ratio of gas effect to shock energy is different in different explosives, it is easy to understand why some explosives perform well in elastic rock and poorly in plastic-acting rock, and vice versa. Some of the most difficult blasting situations arise when mixtures of plastic-acting and elastic rock are encountered (Fig. 4). Fig. 4 shows an example of granite boulders cemented together with something like a decomposed quartz monzonite which is plastic-acting. The elastic granite boulders will transmit the shock-strain within itself, but when this shock tries to move through the monzonite to the next boulder, its intensity is absorbed by the monzonite and little shock-strain is placed on the adjoining boulder. In addition to this loss by absorbtion, shock reflection at the surface of the boulder will effect tensile spalling. The net effect is poor breakage of the boulders which do not have drillholes in them as they simply will be popped out with the muck. The same is true (Fig. 5) when layers and joints make

Jan 1, 1970