Search Documents

By K. Sun

The exothermic behavior of the intermetallic reactions inside an Al-Mn metallic powder compact and its assimilation fundamentals in molten aluminum were examined. In this study cylindrical compacts were manufactured and tested. The experimental work involved simultaneous temperature measurements of three thermocouples as well as detection of the apparent weight of the cylindrical specimen during its assimilation in liquid aluminum. The details of the intermetallic reactions prior to the compact complete disintegration were investigated by microscopically studying the morphology and local composition in a partially reacted compact. The variation of manganese concentration in the melt was determined by chemically analyzing the samples taken from the molten aluminum at specific time intervals. The exothermic reaction increases the compact's temperature above that of the liquid aluminum. In tandem with this exothermic reaction, the compact is suffering a swelling action. This swelling action disintegrates the cylindrical specimen, which is assimilated into the liquid aluminum. The intermetallic reactions proceed in a stepwise manner. Both the bath temperature and the compact composition impact on the exothermicity of the intermetallic reactions. However, when the amount of Mn in the compact is greater than 75-wt%, the maximum centerline temperature rise is slightly reduced as Mn amount increases.

Jan 1, 2004

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) has been used by the mining industry for early fire detection in underground mines. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to integrate real-time AMS sensor data with NIOSH’s mine fire simulation program, MFIRE 3.0, to simulate and predict the spread of smoke that would provide assistance to mine fire emergency response personnel. Determining the heat release rate of a fire using the monitored sensor data was a critical component of the successful completion of this project. NIOSH researchers developed a direct method to calculate the heat release rate when a fire is within close range of sensors. However, this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire heat release rate for complicated scenarios where a fire is distant from sensors and airflow splits and merges are present. The method was validated using a fullscale diesel fuel fire test conducted in the Safety Research Coal Mine at the Pittsburgh Mining Research Division and can help mine operators and safety personnel make informed decisions during a fire emergency.

Jul 31, 2020

By R. Berton, M. Walden, S. Melberg, N. Rocco

Recent tailings dam failures around the globe have influenced many mining industry regulators to reassess their requirements for the numerical modelling of tailings dam failures. This type or forward modelling is associated with overarching uncertainties as the model cannot be calibrated against a physical result. Dam breach analyses that meet the requirements of current industry standards and guidance typically begin with identification of credible failure modes and selection of appropriate topographic data set to represent the study area. The breach parameters and the volume of tailings released are then determined using available methodologies and empirical relationships. Subsequently, when the breach hydrograph is developed and the hydrology of stream networks are complete, the runout simulation is implemented. Due to the uncertainty involved in the process, sensitivity analyses are recommended to quantify variations in model inputs on the inundation extent and the flow characteristics. This paper outlines some common methodologies utilized for development of dam breach models, summarizes associated uncertainties with these methodologies and inputs, and provides guidance on how sensitivity analyses can address a wide array of uncertainties inherent in tailings breach analyses. This paper provides an understanding of how selecting appropriate breach parameters can result in reasonably conservative inundation extents consistent with the identified credible failure modes.

Mar 2, 2022

By Felipe Calizaya, Sekhar Bhattacharyya

Mechanized underground mines suffer from noise overexposure. Noise levels are often above the Permissible Exposure Limit (PEL) where underground fans are used. Sound levels in active workings can reach up to 121 A-weighted decibels (dB(A)), especially when fans are not equipped with silencers. Use of silencers seldom ensures PEL. Overexposure of noise induces permanent hearing loss among mine workers. A NIOSH-funded research project and field studies at six coal and non-coal mines revalidated the findings. The University of Utah undertook laboratory studies to reduce fan noise at the source. A new silencer prototype with varying noise dampening material was designed and tested. The silencer and associated extension can be repacked with different dampening materials. The silencer and the extension were used in various configurations. Attempts were also made to simulate field conditions. The tests demonstrated a maximum sound level attenuation of about 14 dB(A) at the fan discharge. A properly designed silencer offers lesser resistance and thereby better fan performance and lower energy cost. The re-packable silencer is more likely to be maintained properly. Lowering of noise level happens in audible frequencies (4000 to 8000 Hz) which are important in A-weighting.

By B. D. Pandey, D. Bagchi, Premchand

During the separation and recovery of metals from the ammoniacal leach liquor of Indian Ocean nodules by solvent extraction-electrowinning (SX-EW) in close-loop operation, the copper electrolyte containing ~40g/L Cu, 20 g/L Ni and 180 g/L sulphuric acid is bled-off to control the impurities. The recovery of copper and nickel as powders has been examined from the copper bleed solution following partial decopperisation, crystallization of mixed sulphate of the two metals and aqueous hydrogen reduction. From the dissolved sulphate solution containing 17.68 g/L Cu, 18.83 g/L Ni and 0.03 g/L Fe, the copper powder was precipitated at initial hydrogen pressure of 26 bar in an autoclave in 90 min at 140 °C. The residual copper from the spent solution was removed as sulphide and nickel powder was then recovered (99%) in two stages from a solution of pH 4.5 at 40 bar pressure and 190 °C. However, 98% nickel recovery in one stage was achieved when hydrogen reduction was carried out from an ammoniacal solution in the pH range 9-11. Copper and nickel powders were produced from the bleed solution with acceptable purity and specifications suitable for P/M applications.

Jan 1, 2004

By K. E. Hjelmstad

During an underground mine fire, air can be rapidly depleted of oxygen and contaminated with smoke and toxic fire gases. Any delay in warning miners could have disastrous consequences. Unfortunately, present mine fire alarm systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in mine area coverage. Recent research by the U.S. Bureau of Mines has demonstrated that ultra low frequency electromagnetic signaling can be used for an underground mine fire alarm. In field tests of prototype equipment at five mines, electromagnetic signals from 630 to 2,000 Hz were transmitted through mine rock for distances as great as 1,645 m to an intrinsically safe receiver. The prototype system uses off-the-shelf components and state-of-the-art technology to insure high reliability and low cost. When utilized, this. technology would enable simultaneous and instantaneous warning of all underground personnel, regardless of their location or work activity, thereby increasing the likelihood of their successfully escaping a mine disaster. This report presents the theoretical basis for through-the-rock ultra low frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 2010

By J. P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, including two red shale, two fireclay, a silica, a silicon carbide, a carbon, and a high-alumina brick, were evaluated. Samples were exposed to 40 wt pct HN03 at 70° and 90° C and 60 wt pct HN03 at 50°, 70°, and 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were generally small or not detected, except for a strength drop in the high-alumina brick, which decreased in strength when exposed to the chosen acid concentrations at 90° C. Vol-ume and weight changes were also measured. The leach rates of Al, Ca, Fe, K, Mg, Na, Si, and Ti were monitored. Increasing temperature or a decrease in the acid concentration resulted in an increased ion leach rate. Of the conditions tested, the most severe corrosion occurred at 90° C for a 40-wt-pct-HN03 solution. The silica brick had the best overall acid-resistant properties, followed by a red shale and a fire-clay brick. The carbon and silicon carbide bricks are not recommended for service.

Jan 1, 1984

By Alex Ryberg, Matthew L. Becker

Several integrity testing methods exist which may be used to evaluate drilled shafts. Each test method has advantages and limitations. On occasion, the results from different test methods may lead to conflicting conclusions, making it difficult to conclusively know which results more accurately represent the quality and integrity of a drilled shaft. This case study focuses on the integrity testing evaluation for two drilled shafts which were constructed using permanent casings and installed through flowing river water. Integrity testing was performed using Thermal Integrity Profiling (TIP) and Crosshole Sonic Logging (CSL) on each shaft. During testing, the influence of flowing water and soil layering needed consideration in the collected TIP data. Similarly, concrete curing time influenced the CSL test results and required the CSL tests to be performed multiple times with additional wait times following concrete placement. To aid in the shaft integrity evaluations, Low Strain Integrity testing via the Pulse Echo Method (PEM) was performed on several shafts and concrete coring was also performed to help further assess the acceptance or rejection of the questionable shafts. This paper presents an overview of the testing methods that were applied, their basic methodology, as well as potential limitations that should be considered when evaluating their results.

Sep 8, 2021

By Robert K. Koch

The Bureau of Mines investigated separating HF from HF-SiF4-H2O mixtures by passing the mixed gases through a sodium fluoride slurry in an airlift scrubber and forming a mixed precipitate of NaHF2 and Na2SiF6. The oven-dried precipitate was thermally dissociated in two stages. The first stage was carried out at 400° C and dissociated NaHF2 to NaF and HF. Condensation and analysis of the evolved HF proved it to be 97 to 99 weight-percent HF containing 0.79 to 0.99 weight-percent H2O and 10 to 93 ppm silicon. The second stage was carried out at 700° C and dissociated Na2SiF6 to NaF (for recycle) and SiF4. The quantity of HF recovered from gaseous HF-H2O-air mixtures decreased with increasing relative H2O concentrations. Air was beneficial when scrubbing extremely dilute wet HF gases. At HF partial pressures of 0.24 and 0.013 mm Hg in the scrubber entrance gases, HF partial pressures of 6.2 x 10-4 and 9 x 10-6 mm Hg were obtained, respectively, in the scrubber exit gases. Scrubber efficiencies were 99.7 and 99.3 percent.

Jan 1, 1966

By D. M. Wade, F. F. Redfield

PRODUCTION at Aguilar started in 1936 and by 1942 the mine had reached a peak of 25,000 tons a month. Present production is only about 60 per cent of this capacity because of difficulties in railroad transportation and the rationing of fuel oil brought about by the war. In the early years, cut-and-fill stopes were tried, but square sets were found to be the most practical method in the southern section of the mine, where blocky, treacherous ground and greater mining widths are prevalent. Square sets and opencut mining were the rule until 1942, when it became increasingly difficult to get mine timber. The ore beds in the northern section of the mine were found amenable to cut-and-fill stoping as the rock was firmer and the veins narrower. At present 69 per cent of the ore comes from cut-and-fill stopes, 27 per cent from opencut, and only 4 per cent from square-set stopes. Massive galena and sphalerite with comparatively little quartzitic gangue constitutes the higher-grade ore. The gangue minerals that can be detected by eye in low-grade ore are rhodonite, wollastonite, and pyrrhotite. Wall rocks range from shale to quartzite, with occasionally a little limestone.

Jan 1, 1947

By R. A. Ford

The paper outlines: methods used for the determination of wear metals in motor and transmission oils; contaminents in motor, transmission and crusher lubricating oils; and viscosity determinations. Case histories and costs are presented to illustrate the value of an oil analysis program. Introduction NORANDA MINES LIMITED (BELL COPPER DIVISION) is located on the shores of Babine Lake, approximately 450 miles north of Vancouver, British Columbia. Access to the mine is by road from Topley, B.C., about 40 miles away. When a preventive maintenance analysis program was first considered, it was obvious that if samples were to be sent out for analysis, results would not be available for at least a week, due to the distance from any commercial laboratory. The assay laboratory was asked to investigate the possibility of determining wear metals on site. A limited program was started soon after production commenced, and this has now grown to include all large mobile equipment as well as crushers and grinding mills. The laboratory also now determines viscosity, fuel dilution, dirt and abrasives, glycol and water. All these results are ready within two days. This paper will outline the methods used, data interpretation, several case histories and the benefits from such a program.

Jan 1, 1977

By L. M. English

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point But wait a minute: Isn't head loss a negative number, a debit? And isn't fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves -pressure losses as negative values and energy additions as positive values -and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at \\tIich the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation net\wrk. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1997

By J. Labuschagne

The primary factor contributing to the profitability of a platinum mine and its associated concentrator is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. To minimize the time it would take to produce concentrate without stopping because of a lack of feed material a project was undertaken to integrate the mining model with a concentrator production schedule () in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where ?visual pollution? is to be avoided. To achieve this a dynamic stockpile model was created utilizing the mine production schedule resolved into a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ores. The stockpile levels were never allowed to fall below zero to prevent a situation where the concentrator was operational without feed material,. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, that was then used as a basis for commercial concentrate sale negotiations.

Jan 1, 2012

By M. O. Serbousek

The load-transfer mechanics of fully grouted roof bolts in coal mines have been investigated in laboratory and analytical studies. The purpose of this Bureau of Mines research is to increase understanding and better interpret data from routine field pull tests and to develop a numerical model of a grouted bolt that can be used in a global computer model of a mine roof. Analytical studies using closed-form solutions and finite-element techniques were compared to experimental results. Laboratory work includes variation of bolt length, hole diameter, and grouL type. Pull tests were pel'fol·med on 4-, 2-, and I-ft bolts in holes of 1-and I-3IB-in diameters. Both polyester resin and inorganic grouts were used as the anchorage medium. Strain gauges were installed on the bolts at several locations to observe the rate of load transfer from the bolt through the grout to the rock mass when a force was applied at the bolt end using standard jack pull testing procedures and equipment. The average anchorage length of 4-and 2-ft bolts was 22 in. Grout type and hole size variations did not produce a significant effect on the rate of load transfer from the bolt to the rock.

Jan 1, 1987

By M. S. Eygi

This study covers the investigations based on the electrokinetic and rheological properties to explain the interactions between kaolin minerals and commercially available polyelectrolyte in anionic character. Additional adsorption test were also conducted to support the interaction mechanism. Adsorption tests showed that adsorption densities decrease by increasing the solid content. In-creasing the solids contents from 1% to 30% by weight resulted in the decrease on adsorption from 2.14 mg/g to 1.85 mg/g. Because of its difficulty, the solids ratio at 70% was not studied. However, following to trend of the curve plotted adsorption density-solid ratio, an estimation was made and adsorption density at 70% solid content was extracted from the curve as 1.75~1.80 mg/g. The electrokinetic studies pointed out that the presence of polyelectrolyte increase the zeta potential of kaolin from 40 mV to 60 mV which is reasonable conditions to disperse and stabilize the kaolin slurry and lower the viscosity. When these result of the different tests are combined and considered together, 2 mg/g polyelectrolyte concentration was noted as optimal concentration where adsorption density, viscosity and zeta potential of the slurries give maxima and remain constant after this concentration.

Jan 1, 2014

By Larry F. Brown

Mining has been the mainstay of the Woods Creek Valley for more than a century. The head of the valley is at the Continental Divide, about 50 miles west of Denver, Colorado. First, it was the quest for gold and silver that drew people to the valley. Then, when molybdenum was classified as a strategic metal by the U. S. Government during World War I, it was the valley's molybdenum mineralization which attracted the most attention. Molybdenum is used primarily as an alloying material in superior grades of steel. Circumstances responsible for providing the label "Urad" are unknown, but Urad is variously reported to be an acronym for "Uranium Research and Development" or "Uranium Research of America Division". The search for uranium was fruitless as no ore grade uranium exists in this area. The moly orebody was first developed and mined by the Primos Exploration Company from 1914 to 1919. During World War II, the mine was purchased by the government and turned over to the Molybdenum Corporation of America to operate. In 1963 AMAX Inc. purchased the property for $2 million. After spending nearly $30 million for exploration and development, AMAX put the mine into production again in 1967.

Jan 1, 1984

By D. S. Kingery, F. F. Kopsch

The practice of using two or more main ventilating fans is common at large coal mines throughout the coal-mining industry. To assure adequate and efficient ventilation at may mines, such multiple-fan systems are necessary. The hazards associated with interrelated ventilating currents if a fan fails are controversial, and to date little effort has been made to study this specific problem and to determine corrective measures. The obvious questions are: 1. Is there a hazard? 2. Under what circumtances does it exist? 3. How serious is it? 4. What are corrective measures? Most members of the mining fraternity agree that reduced quantities of air and changed airflow patterns introduce potential hazards, especially where gaseous conditions exist when mechanized methods are used in concentrated mining 0 The seriousness of the hazard depends on the ease with which methane accumlates in face areas or haulage roads, the quantity of methane in workedout areas, and the extent to which reversed air currents interfere with escape and recovery operations after mine fires or explosions. These studies cover three mines and give the distribution of air for the specific conditions show. Each mine probably has somewhat different airflowpressure relationships between fans. This depends on the number of fans, the

Jun 1, 1959

By R Shaw, T T. Neidel, C Adams

Sampling equipment manufacturers endeavour to ensure that the mechanical equipment installed in sampling systems are designed and manufactured to adhere to the requirements of the International Organization for Standardization (ISO) or other standards relevant to the application. The mechanical parameters necessary to achieve these standards can be well controlled and requirements such as constant speed can be met through good mechanical design and engineering. However, when the equipment is installed and put into operation, the ISO compliance of the system is out of the hands of the equipment manufacturer and handed to the operator, who may be a generalist control system integrator.Making a sampling system perform according to standards, and being able to monitor and report on compliance require that the sampling system knowledge and the control integration is combined and applied in an integrated approach. Using a dedicated library of control routines developed for sampling can change a system from having compliant equipment to being a compliant system. The library has to include monitoring of relevant parameters and control and reporting on sampling parameters.CITATION:Neidel, T T, Adams, C and Shaw, R, 2014. Control and monitoring of International Organization for Standardization compliance for industrial sampling systems, in Proceedings Sampling 2014 , pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Blair R. Benner

This paper describes the installation and operation of a Texas Nuclear on-line silica analyzer (NOLA) coupled with a Leeds and Northrup Microtrac particle-size monitor (Microtrac) at U.S. Steel's Minntac taconite concentrator. An automatic sampling system provides the NOLA with samples of final concentrate. After the sample is analyzed for silica by the NOLA, it is pumped to the Microtrac for size and surface area measurement. A sample is analyzed every six minutes, providing the control room with the silica concentration, the percent passing 270, 400, and 500 mesh, and an equivalent Blaine surface area number. When fed a slurry of final concentrate containing between 20 and 70% solids and 5 to 6% silica, the NOLA analysis is within ±0.2% of the wet chemistry silica. The agreement between the Microtrac output and standard screen analyses is ±1.2% at 270 mesh; ±1.5% at 400 mesh, and ±2% at 500 mesh. The poorer disagreement at the finer sizes is mainly due to inaccuracies in screening at 400 and 500 mesh. The agreement between Microtrac surface area a d laboratory Blaine surface area is about 9 ±80 cm 2/g. These instruments provide rapid and reliable feedback information to the concentrator and feed forward information to the agglomerator.

Jan 1, 1984

By C. J. Greet

Grinding with an electrochemically inert grinding media (i.e., high chrome white iron) shifts the pulp potentials to more oxidising conditions, increases the dissolved oxygen content and reduces the EDTA extractable iron concentration when compared with milling with electrochemically active grinding media (forged steel). These changes in pulp chemistry produce cleaner particle surfaces, reduce reagent consumption, and increase concentrate grades and recoveries. This paper presents a robust laboratory test program that not only demonstrates the changes in the pulp chemistry, but also provide an indication of the magnitude of the metallurgical improvements that are possible. While laboratory studies are interesting, the proof is in the pudding! So, the paper provides an overview of plant trials conducted at several porphyry copper operations around the world: Newmont’s Cadia and Red Chris Operations, as well as Evolution Mining’s Northparkes Operation. These successful plant trials clearly demonstrate that selection of the right grinding media alloy will yield savings in grinding media consumption and reagent consumption as well as increases in revenue through improved copper and gold recoveries. However, many of the porphyry copper mines on the Eastern Pacific are copper-molybdenum deposits. The paper presents laboratory test results for typical copper-molybdenum operations and extrapolate these numbers to what might be expected should a plant trial occur.

Feb 1, 2025