Search Documents

Neutralization with lime is a simple, cheap, and effective means of treating acid raffinates from uranium processing to' raise the pH, reduce the concentrations of dissolved salts (including heavy metal impurities), and remove amine by adsorption. Two-stage neutralization, using limestone in the first stage at approximately pH 4 and lime in the second, lIlay be advantageous.Lime neutralization of mffinates in the pH range 7 to 8· 5 generally reduced the radium ·concentration to 10 to 200 pCi 1-1, but ·there was considerable scatter in the experimental data. The radium concentration was further reduced to less than 3 pCi 1-1 by co-precipitation of barium (radium) sulphate with 10 mg Ba (as barium chloride) per litre of raffinate. Adsorption of radium on barytes was -also effective in reducing the radium concentration in neutralized raffinate to less than 3 pCi 1-1.The radium concentration of pit water was readily reduced to less than 3 pCi 1-1 when pit water containing 0·01 M sulphate as ammonium, calcium, or sodium sulphate was treated with 20 mg Ba per litre of pit water.Adsorption on barytes was also effective in removing radium from pit water containing 0·03 M sulphate.

Jan 1, 1975

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By C. D. Thompson

Pile load test programs were carried out in 1984 and 1985 at Stelco's and Dofasco's Steel Making Plants in the Hamilton Bayfront area. 323.9 mm outside diameter by 9.5 mm wall thickness Grade 3 steel closed-end pipe piles were driven to practical refusal at depths of 21 to 30 m in very dense silt till with Delmag D30 open-end diesel hammers. Ultimate bearing capacities of up to 5330 kN were proved by dynamic monitoring and static load tests. Allowable bearing capacities of 1780 kN were achievable on production piles without undue difficulty. It was found that the impact stress at the top of the pile was controlled by the yield strength of the steel rather than a useable upper limit based on the modulus of elasticity. A bearing to impact stress ratio of 1.2 at practical refusal was observed to be reasonable but conservative at this site, and is felt to be generally applicable for piles driven to practical refusal elsewhere. Dynamic monitoring during production pile driving was able to show that apparent relaxation was caused by pre-ignition of the hammer when visual observations indicated that pile driving was proceeding satisfactorily.

Jan 1, 1987

By Gabriel S. Esterhuizen

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as ?Good? to ?Very Good? using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

Jan 1, 2006

By M. T. Davisson

Pile compression load capacity prediction methods are divided into four categories for purposes of discussing their reliability compared to static load test results. The categories considered are: 1) static analysis, 2) driving formulas, 3) wave equation analysis, and 4) dynamic measurement and analysis. It is concluded that any method of static analysis that works for the geological deposit in question may be satisfactory. However, any given method can be quite wrong when applied to other deposits of soil that are different in terms of their engineering and geological characteristics. Dynamic formulas are found to be theoretically unjustifiable. The ready availability of the wave equation analysis for microcomputers eliminates the need to utilize dynamic formulas. The wave equation analysis is found to be the best analytical method for making predictions both for design and for construction control. Dynamic methods of measurement and analysis are found useful, but have limitations that have caused troubles on many projects. Two case histories are presented that show the limitations of dynamic measurement and analysis, and of the wave equation analysis. Soil deposits exist that defeat both the wave equation and dynamic measurement techniques; static load tests are currently the only method of proving the load capacity of piles in such soils.

Jan 1, 1991

By S. O. Bada

Coal samples taken from the No. 2 Seam and No. 4 Seam in a South African colliery were tested in a rotary triboelectrostatic separator. The two-stage triboelectrostatic separation results using the -177 µm size fraction reduced No. 2 Seam coal containing about 30.4 per cent ash to a clean product of 8.9 per cent and 13.1 per cent ash with combustible recoveries of 9.6 per cent and 30.7 per cent respectively. The same separation approach on No. 4 seam feed coal, which contained 36 per cent ash, produced a clean coal product with 10.8 per cent ash at a combustible recovery of 6.0 per cent. Petrographic tests show a significant improvement in the vitrinite content and a reduction in visible minerals encountered when using the triboelectrostatic separator, with about 53 per cent vitrinite reporting to the clean fraction for No. 2 Seam compared to the feed content of 21 per cent, and a 54 per cent vitrinite in the clean No. 4 Seam from a feed content of 21 per cent. Significant sulphur reductions were also observed after separation in both coal samples, with a better separation in the second-stage coal products.

Jan 1, 2012

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that contains between 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By V. Izaxon

Current practice in mining frozen, underground placers is to support the mine openings by leaving remnant pillars, which are kept frozen to maintain their stability. These pillars may be partially extracted depending on mining conditions, but this practice may be risky, and roof falls are common. Instead of allowing the mined-out areas to cave, the extracted entries could be filled with waste material, which would then be frozen, using cold ventilation air. A finite difference model for analyzing the effects of various parameters on the freezing of backfill in underground mines in the Arctic has been developed and tested. The model also accounts for properties unique to a frozen rock mass, including those that change with temperature. Examination of the characteristics of ice-cemented mining waste materials as backfill indicates that with proper engineering control, a backfill system can be designed for use in production mines. The system will allow increased extraction ratio while maintaining the stability of underground openings with minimum heat impact on the surroundings. These simulated results establish the relationships among the strength, the temperature, and the freezing characteristics of a given material. When coupled with site observations these relationships will facilitate the optimal design of ore pillar recovery methods.

Jan 1, 2004

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. But wait a minute: Isn't head loss a negative number, a debit? And isn't fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves - pressure losses as negative values and energy additions as positive values-and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Feb 24, 1997

By Gregory J. Canivan

Three test pile programs were conducted in Charleston, South Carolina to evaluate differences in bearing resistance due to installation methods. The tested piles were installed with impact hammers and vibratory drivers through soft clays and/or loose sands into the Cooper Marl, a stiff calcareous marine clay or silt. Piles driven into the Cooper Marl experience significant capacity gain with time following initial installation due largely to pore pressure dissipation. Pile size and pile type were both known to affect pore pressure generation during installation and subsequently the capacity gain with time. The test programs were primarily conducted to optimize pile design values and construction methods with regard to trestle construction but the results also contribute to the understanding of driven pile behavior. High strain dynamic testing was performed on several open-end pipe and H-piles. The measured difference in long-term bearing capacity of the H-piles as a result of the two installation methods was negligible, while the short-term bearing capacity of the pipe pile was larger when the piles were installed using impact hammers. The lower short-term resistance in the vibratory driven piles is attributed to larger excess pore pressures generated during installation compared to those generated during impact driving.

Jan 1, 2002

THE slide-rule, as a quick and convenient instrument for performing approximate calculations, is steadily growing more and more into favour with the engineer, and results obtained by it are considered close enough to enable him to satisfactorily dealwith a considerable portion of his work. To the surveyor, however, whose ordinary computations must be as precise as his measurements, the present makes of rule are insufficient, except for a very narrow margin of the scales and for rough work. Few will carry the rule when they can clearly see that it is unreliable for general routine, and the careful surveyor is inclined to look askance at those who do use it, recognizing the temptation there undtmbtedly must be to push it into work that the log book should be called upon to treat. From the fact that a surveyor's duties take him on the surface in all weathers, and underground in many wet and uncomfortable places, where the manipulation of a book of mathematical tables becomes both awkward and patience-trying, an efficient slide-rule must offer the mbst transparent advantages. Again, a surveyor being specially trained to read divided scales quickly and accurately, the slide-rule must commend itself as an apt addition to his outfit.

Jan 1, 1912

When Haematite Explorations Pty. Ltd. began prospecting for petroleum in 1960, there was only ill-defined geological evidence on the land bordering Bass Strait to support the belief that petroleum lay trapped in sedimentary formations beneath its shallow waters.A reconnaissance of the area, made in 1961 by the airborne magnetometer method, covered the waters and islands of the Strait and overlapped the Victorian and Tasmanian coasts. The survey indicated the presence of the Bass Basin (which is completely water-covered), assisted in outlining the Otway and Gippsland Basins, and showed that each basin contains sedimentary rocks over 10,000 ft thick. Information on the regional geology and minor volcanic activity was also obtained.Marine seismic surveys carried out from 1962 to 1965 defined these basins more accurately and showed the nature and structure of the thick sedimentary sections.Correlation of the seismic data with onshore wells identified the sediments as Tertiary and Mesozoic. Subdivisions of the former in all basins and the latter in the Otway Basin were made. These Tertiary and Mesozoic rocks are not seriously deformed and they have good prospects of containing petroleum.Possible structural and stratigraphic traps, recognized from the seismic record sections by petroleum geologists, are being tested by offshore drilling which began in 1964.

Jan 1, 1966

The first part (lH of this work dealt with the process of recrystallization of single crystals of lead after deformation by creep, as revealed by macroscopical examination. It was shown that when recrystallization commenced, a crystal, termed the primary crystal, started to grow at the edge of the specimen and extended into the body of the specimen along the slip planes. At some stage during the growth of this crystal, other crystals appeared at the boundary of this first crystal and fragments of the parent crystal. From thispoint, recrystallization was accelerated with relatively rapid necking down of the specimen until fracture occurred.All those crystals formed after the primary crystal were given the term secondary crystals. In the present paper is given a detailed account of the orientations of the primary and secondary crystals.EXPERIMENTAL METHODThe size of the test pieces and the manner of loading were given in the previous paper (1). X-ray back reflection photographs were taken of the individual primary and secondary crystals and from them were determined the orientations. The path of the X-ray beam was perpendicular to the surface of the creep specimen.In view of the large number of photographs needed, gold...

Jan 1, 1940

By David Flores, Benjamin Cebrian

Gold mining require high levels of dilution control due the high value of ore. These types of operations employ short benches, which are suitable for ore control, lower displacement and more representative block models. However, shorter benches makes fragmentation by blasting difficult because blast designs tend to be stiff in regards to burden/bench height ratio. This is especially relevant in hard, massive ore bodies where usual drilling diameters lead to poor energy distribution. In regards to control ore loss and dilution, there are different techniques to minimize both, which include: panel blasting, buffer blasting to muck piles and differential loading of areas of the blast bench. All of them should be sequenced with appropriate displacement along the ore/waste contacts. This paper describes extensive engineering approaches to achieve both dilution control while not hurting fragmentation in the very hard, massive ore sections of a mine case study. Ore Tracker microchips are used to correlate performance of these designs at the SAG mill (bottleneck of this specific operation). Another gold mine uses the same technology to detect when and where operational dilution is happening. The system tells where flagging of the different ore bodies has been followed in order to detect which operators pass the excavation limits beyond ore control flagging.

By P. Hickey, J. Spenceley, T. J. DeMull

Development of the Batu Hijau Project was successfully completed in the fourth quarter of 1999 with the final handover and start-up of ore processing facilities. The development project had started more than three years earlier, in August 1996, when the Owner, PT. Newmont Nusa Tenggara (PTNNT), awarded an EPC contract to Fluor Daniel (FD) for design and construction of the project including: copper concentrator, port, power plant, town site, and infrastructure. PTNNT managed the development of the mine and procurement of mine equipment with its own forces. Bringing the Batu Hijau copper deposit into production was the largest mining project ever undertaken. Development of Batu Hijau was a complex project involving the work of tens of thousands of people in all parts of the world to complete engineering, manufacture and deliver equipment, supply materials, and build the plant. The ore deposit is located on the tropical island of Sumbawa in a remote and undeveloped section of Indonesia. The location and environment presented challenges for all phases and aspects of the project. To meet the challenges, the project team combined good planning and teamwork to best utilize the resources available. This approach assured continuity of personnel through construction to operations and minimized cost, resulting in completion of the project ahead of schedule and under budget.

Jan 1, 2001

In exploiting the ultra-deep, narrow reef ore bodies of the Witwatersrand, the ventilation and cooling systems within the stopes play a critical role because of high concentrations of active workers. This paper examines the heat, ventilation and cooling effects of a number of different stoping layouts for narrow reef mining in ultra-deep operations in very hot rock. The stope ventilation and cooling needs are driven primarily by the difference between the air temperature and that of the rock front being excavated. These needs depend on the face utilization, geometry, face advance (rate and direction), layout, backfill, use of water and machinery1,2,3. Detailed studies of different stoping configurations have been undertaken for mining operations extending to depths of 5000m below surface, where virgin rock temperatures approach 70°C. Extensive work has been completed with regard to evaluating ventilation and cooling requirements to maintain air reject temperatures of 28°C wet-bulb and better. This knowledge is being used to determine overall cooling requirements, reduce operational costs and maximize the efficiency of cooling systems. These issues are important when considering both the local and regional air conditioning systems and the most effective application of in-stope chilled water.

Jan 1, 2001

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

By S. Kevin McNeil, William Joa, Catherine Johnson, S. Omar Garcia

The geometry of an explosive is known to have a fundamental effect on the resulting shock wave propagation. Typically researchers use a spherical or hemispherical geometry in order to simplify the shock wave so that resultant overpressure and impulse are uniform in all directions. The goal of this research is to understand the overpressure characteristics from a sheet explosive, a geometry often utilized for breeching in the military. In training alone, soldiers can be exposed to several tests per day, which may be contributing to the prevalence of blast induced mild traumatic brain injuries. Using PCB pressure transducers and high speed video, it was found that as the angle departed from normal (perpendicular) to the face of the sheet explosive, the over pressure decreased significantly. When in line with the plane, a decrease of over pressure by as much as 20% was observed. Time of arrival was roughly 20% faster directly in front of the charge with a pressure amplification of 46% relative to a spherical baseline charge of the same mass. This testing may reveal a more complete relationship between the pressure and angle from the explosive that could have applications for military and law enforcement with respect to best practices on blaster location for reduced over pressure exposure.

Jan 1, 2019

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006