Search Documents

By TvS. von Moltke

Steel is a highly versatile material due to its low cost and good mechanical properties, but typically needs some or other form of corrosion protection due to its tendency to corrode when exposed to atmospheric conditions. In the case of organic coatings, the corrosion protection and functionality of the final product is critically dependent on the adhesion of the coating to the surface of the steel. In this work the effect of contaminants and the nature of the surface layers present on industrial steel products are investigated by means of paint adhesion tests, Auger electron spectroscopy (AES), and X-ray Photoelectron spectroscopy (XPS). It was found that the presence of sodium species on the surface is very detrimental to paint adhesion under wet conditions, while satisfactory adhesion may be obtained even in the presence of silicon and carbon residues. It was also found that the nature of the Fe-O layer, formed under wet conditions is labile and different from that formed in dry air, and that subtle changes in process conditions, such as changing the oxygen content of the quench water, may change the adhesion of paint to the surface of the steel. Lewis acid-base interactions are discussed as a mechanism that may determine the bonding between the steel and polymer coating.

Jan 1, 2003

By Stephen P. Signer

To improve the understanding of the support interaction mechanics between grouted bolts and coal mine roofs and to help lay the foundations for improved design and evaluation techniques, the 0.8. Bureau of Mines has conducted laboratory, field, and analytical studies of the load transfer mechanics of grouted roof bolts. Mechanisms by which load is transferred from a bolt through the grout to the rock mass are analyzed. Strain gauges were installed on over 70 bolts and tested to observe the rate of load transfer when a force was applied at the bolt head. Laboratory and field tests were conducted to determine bolt-grout- rock interaction behavior in both the elastic and postyield phases. Long-term laboratory tests were run to determine the time-dependent properties of both polyester resin- and-gypsum-grouted bolts. Numerical studies using finite- element techniques were compared to the experimental results. Elastic tests showed that 90 pct of the applied load was transferred within 24 in of bolt length. Long-term tests indicated that creep is more significant in gypsum-grouted bolts than in resin- grouted bolts. Plastic studies showed that yielding of steel will translate down the length of the bolt from 6 to 20 in.

Jan 1, 1988

By C. J. H. Steenkamp

Theoretically, the main driver behind a mining operations? sourcing decision should differ from company to company, and within a company from project to project, but in reality it often relates to cost. Research confirms that there are a number of factors, including cost, to consider when choosing between in-house and outsourced mining. While the literature is rife with factors to consider, little information exists on how to apply these in practice and the relative importance of the different factors to be considered. A study was conducted to determine whether mining is truly a core competency for a mid-tier commodity specialist mining company. Furthermore, a decision-making framework for mining operations sourcing was developed, and the critical success factors that should be adhered to if outsourced mining is chosen were determined. The research showed that owner mining is not a core competency for the mining company investigated. A decision-making framework was developed using the order winner/order qualifier structure, which can be used to facilitate the mining sourcing decision. The most important tools at the disposal of a mine owner?s team to manage a contractor miner are the social and output control mechanisms, according to the critical success factors study.

Jan 1, 2014

The material presented in this paper describes experimental work to determine the effect of variations in suction nozzle design upon inlet flow conditions. Four entrance profile shapes were examined under controlled conditions of slurry flow and it was found that the straight ended nozzles had consistently higher entrance losses than the straight taper or the ellipse, and that the circular arc profile nozzles were the most efficient. Subordinate considerations were the measurement of the quantities and the forces involved.As the work progressed, three distinct phases in the pattern of flow were apparent and the static pressures in each were carefully examined. An inlet zone was found to be unstable in changing boundary conditions, a transition zone was largely independent of slurry density and in a zone of stability the pressures were found to be directly related to the characteristics of the flowing pulp. In this zone pressure measurements were reproducible within ± 2 per cent regardless of changing boundary conditions.The effect of varying the "1" parameter of nozzles with a part circular entrance profile was examined and it was found that flow conditions approaching the ideal were obtained when the radius of curvature was between 0·40 and 0·550.

Jan 1, 1966

By Todd M. Ruff

The majority of fatalities that occur in road construction work zones in the United States involve a worker being struck by a piece of construction equipment or other vehicle. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these accidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers on foot or other objects. Several cameras and sensor systems are available for this application, and a study was conducted to evaluate these systems on various trucks used in road construction and maintenance. Tests were conducted using sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted using dump trucks during the warmer months to study the effectiveness of the systems in highway work zones. Results show that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in crowded work areas.

Jan 1, 2004

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By Steve Jones

Minor subsidence damage to the Burgettstown Junior-Senior High School building and grounds near Burgettstown, Washington County, Pennsylvania, prompted an investigation of the site in early 1985 by the Bureau of Abandoned Mine Reclamation of the Pennsylvania Department of Environmental Resources. The investigation determined that subsidence over an abandoned coal mine was occurring and that additional damaging subsidence would occur if reclamation measures were not taken. A Pittsburgh Coal Seam Mine which was abandoned in the 1920's underlies the school at a depth of sixty-five (65) feet. This sixty-five foot section is comprised of five (5) feet of unconsolidated overburden and sixty (60) feet of thinly bedded, highly fractured shale. Approximately five and one-half (5-1/2) feet of Pittsburgh Coal was extracted at the school site. A thin shale binder and one (1) to one and one-half (1-1/2) feet of roof coal were left in place. Within the Contractor's Underground Working Area (See Figure 1) approximately thirty (30) percent of the coal was extracted. It appears that the mine was just being developed in the vicinity of the school when it was abandoned for no known reason. Other nearby portions of the mine show extraction approaching sixty-five (65) percent.

Jan 1, 1986

By C. A. Ozturk

The compressive strength of rock (sc) has an important effect on design of structures in rock engineering. Compressive strength can be determined in the laboratory using the uniaxial compressive strength (UCS) test. Some other index tests, such as the point load test, are also used, particularly when suitable samples for UCS are not available. The quantification of rock texture has introduced a new method in rock engineering for estimating the mechanical and physical properties of rock materials from microscopic investigations. The aim of this study is to quantify rock texture to estimate rock strength from the texture coefficient (TC), which is determined from a statistical assessment of thin section images. Rock texture is quantified by twelve different images from a single thin section to increase the reliability of texture analysis. A data-set is prepared to investigate correlations between TC and sc. The statistical correlations are computed after classifying of the rock samples based on their lithology as well as grain features. Equations derived based on the results of this study are used to predict the approximate value of compressive strength from the texture coefficient. This method is particularly useful for preliminary studies in rock engineering projects prior to detailed site investigation.

Jan 1, 2014

While ring-blasting techniques offer substantial benefits, there are intrinsic problems that are exacerbated when large blocks of ore are mined in attempts to improve the production economics. These problems relate to both the convergence of holes around the ring drive and the charging of up-holes. The size and shape of the ore block concerned should be carefully considered so that good drilling, patterns can be achieved. The hole diameters chosen, both affect and are affected by the size of the ore block. The explosive selected depends on the hole diameter and together with the diameter, determines the nominal drilling pattern. Ring-drilling patterns are best derived through the use of computer software together with engineering judgement. The loading of explosive is necessarily high, and charging patterns require careful thought if overcharging is to he minimised and adequate energy is to be available at all parts of the ore block. Initiation systems are critical to the blasting results, but sub-optimal systems must be adopted if collar priming is practised. In view of all these factors, idealised guidelines can be given for ring design, but it should be recognised that developments in technology may in time change some of these parameters.

Jan 1, 2000

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shafts (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, including the post-grouting of all drilled shaft tips. ? Design and construction of the scour protection for the two main pylons. ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2007

By N. B. Devi

The extraction of copper(II) from sulphate solution was investigated using LIX®984N in kerosene. The parameters that could affect the extraction, such as equilibrium pH, extractant concentration, salt concentration, various diluents, and temperature, were separately investigated. On the basis of slope analysis, the complex formed in the organic phase is proposed to be CuR2, where R is the anionic part of LIX®984N. The extraction equilibrium constant and Gibbs free energy ( G) of the extraction process were determined. The positive value of H obtained from temperature variation studies showed that the extraction process is endothermic. The extraction of copper was lowest when chloroform was used as the diluent. Separation and recovery of copper from a synthetic copper-nickel solution containing 6.35 g/L Cu(II) and 0.58 g/L Ni(II) was carried out using 20%(v/v) LIX® 984N. The separation factor ( = DCu/DNi) was found to be pH-dependent. A two-stage batch countercurrent extraction was carried out at an O:A ratio of 3:4 at equilibrium pH 1.05 for extraction of copper from copper-nickel solution, followed by copper stripping from the loaded organic phase with 15% H2SO4 at an O:A ratio of 3:1.

Jan 1, 2014

By G. Lyle

Since its inception CEMI (Centre for Excellence in Mining Innovation) has focused on facilitating innovative solutions to the mining industry in six strategic research areas; GeoRisk, ConstructMine, ValueMine, FindMine, SustainMine and MineTech (visit www.miningexcellence.ca for details). This paper focuses on CEMI?s largest project to date, Ventilation on Demand (VOD). Energy consumption in mines can account for upwards of 40% of a mines operating cost, with a significant portion of this been consumed by the ventilation requirements. VOD provides a significant opportunity to reduce overall mine ventilation requirements and subsequently energy costs, while potentially increasing mine productivity. CEMI is currently in year 2 of an assessment of VOD, focusing on the financial, physical and equipment viability of utilizing such systems in both new and existing mines. This two year program, to be completed by March 31, 2011, is designed to systematically assess such a system to determine if and when it could effectively be applied in underground mines. The paper will describe the process by which the project was initiated, the demonstration projects established to capture data, the means to interpret the data and the modelling developed to calibrate and predict ventilation system requirements.

Oct 1, 2010

By N. Z. Fotoyi

Keywords: MgO-MgR2O3 refractory, SO2-containing gases, chemical attack The reaction mechanisms occurring when MgO-MgR2O3 refractories are exposed to SO2-containing gas atmospheres were examined. The study examined the characteristic structures of magnesite-chrome, chrome-magnesite and magnesite refractories exposed to SO2-O2 gas mixture at temperatures of 700°C to 1350°C. The phase characterization was conducted with scanning electron microscopy (SEM) and powder X-ray diffractometry (XRD). The results show that the physical characteristics of the refractory matrix along the grain boundaries are important refractory features during chemical attack from SO2-containing gas. Upon heating in SO2-containing gas, the changes in phase-chemical compositions and accompanying grain growth causes loosening of the structure and the pore volume promotes gas diffusion. The chemical reactions that occur form stable sulfate compounds identified as MgSO4, CaSO4 and CaMg3(SO4)4, and lead to disintegration of various phase structures and consequently erosion of the refractory. In conclusion, the reaction mechanisms in MgO-MgR2O3 refractories exposed to SO2-containing gases progress through a combination of structural disintegration and chemical attack.

Jan 1, 2011

By J Taylor, L Richards, M McKenzie

When a collapse in its services shaft caused rapid gas build up and its premature closure in. 1951, the Blackwater Mine at Wiauta was in full production with significant ore reserves yet to be mined. A total of nearly 23 tonnes of gold was produced from the mine during its 44 year life. It was New ZealandÆs deepest underground mine, producing gold from an extensive sub-vertical mineralised quartz reef that averaged 0.6 m in width. Mining was by stoping between adits and short shafts, latterly with the main mine access through the 840 m deep Prohibition shaft. Macraes Mining Company Ltd are presently investigating the possibility of reopening the mine. This paper outlines a preliminary assessment of the main geotechnical factors for achieving the reopening, using recent exploration and old mine information. The greywacke host rock mass in the vicinity of the quartz reef has been evaluated using both these sources, and the paper discusses how the geological structure, intact and rock mass strengths, the rock mass defects, in situ stresses, and groundwater inflows may effect the reopening and support of the prohibition shaft, the excavation methods and support for a new supplementary shaft, and the likely excavation and support requirements for working adits and stopes in the rejuvenated mine.

Jan 1, 1996

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By A. M. Neale

Kriel Colliery has experienced some sub-standard blast results on the overburden. Blast results are considered poor when the fragmentation is too big, back break into the new highwall, capping is experienced and/or excess overburden material is thrown into the void. Poor blasting leads to lower productivity, equipment breakdowns, and poor drilling and blasting results on the adjacent blast, contamination of coal or loss of coal. A simulation was developed in Microsoft Excel to model blasting results while changing various parameters. From the simulation results, it could be seen that a change of blast design could be beneficial. As an example, smaller drilling patterns were simulated (10 m x10 m to 8 m x8 m, and 8 m x8 m to 7 m x7 m in Pit 5 and Pit 6 respectively) in combination with changes in explosives (P700 emulsion vs. ANFO) and drill bit diameter (311 mm vs. 251 mm). The results show that each of the options has a specific scenario that will be most beneficial to the mine. These results are quite specific and subject to variable inputs. The purpose of the example is to demonstrate how the simulation can be used as a tool to asses blast design variations.

Jan 1, 2010

Inpit tailings disposal has been undertaken at a number of mining sites within Australia. This paper presents a brief history of the experience of inpit tailings disposal at the Marymia Gold Operation in Western Australia, including geotechnical aspects of the design. Regular monitoring of the inpit tailings disposal into the K1SE Pit at Marymia has allowed the operators of the mine to assess the performance of the tailings storage against its predicted performance during the design phase. Results of this monitoring indicated that the predicted performance was exceeded and the results have been incorporated into the design of another large inpit tailings disposal, the K1 Pit. Monitoring of tailings disposal to both the K1SE Pit and K1 Pit has allowed the mine operator to make substantial savings from inpit tailings storage when compared with above ground tailings storage facilities. The inpit method of tailings disposal at Marymia has proven to be acceptable from an environmental perspective by reducing the water resource requirements of the project, backfilling pits, which would otherwise collapse with time and eliminating the need for disturbing additional areas of mining leases, which usually accompanies construction of above ground tailings storage facilities.

Jan 1, 1999

By M. K. Larson

The U.S. Bureau of Mines conducted a study to evaluate support interaction between conventional bolts and the rib at two Western coal mines. The principal goal was to develop guidelines for designing rib support under various conditions. At mine A, seven rib bolts were installed with load cells and monitored over a 4-month period. Fifty-seven pull tests were conducted with two types of anchors at various depths. At mine B, 163 pull tests were conducted. Results showed that during the 4 months of monitoring bolt load, tension in the bolts decreased over time in some situations and that anchorage capacity was reduced in a yielded zone. Load-versus-deformation plots from pull tests in the rib showed fundamental differences in anchorage behavior at the two mines, particularly when comparing results of tests in old pillars at mine A and tests in new ribs at mine B. Numerical modeling experiments indicate that coal bonding strength was the most significant factor in determining postyield anchorage capacity. Correlation of anchor yield point with anchor depth were more pronounced at mine A than at mine B; measuring torque may be a reasonable method of monitoring deteriorating anchorage capacity in a rib undergoing fracturing and yield.

Jan 1, 1996

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau's turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987