Search Documents

By Nan Zhou, Jixiong Zhang, Qiang Zhang

"Mining activities under hard roof could easily induce rock burst. Based on the geological conditions of widespread hard roof in China, this paper discusses the type, mechanism of occurrence and prevention of rock burst caused by hard roof from energy evolution point of view. It analyzed the interaction between the solid backfilled body and roof under different backfilling ratios. And by establishing and applying the mechanical model, the deformation of hard roof and energy evolution of the panel under different backfilling ratios were determined, revealing the control effect of solid backfilling on disaster-causing energy. As a result, an innovative method using the solid backfilling method was proposed as a solution to the hard-roof-induced rock burst hazards. Moreover, mine trial was conducted in Panel 6304-1 of Jisan Mine. The result shows that the stress concentration factor of the front abutment stress was only 1.44; the coal dusts in drill holes didn’t exceed the limits and microseism of large energy didn’t occur during mining mining, indicating that solid backfilling mining could be applied as an effective method for preventing rock burst caused by hard roof.INTRODUCTIONSHard roof refers to the thick strata above the coal seam or thin immediate roof. It is strong with poor joint development. After mining, instead of immediate caving, it will overhang for a large area in the gob, resulting in high stress in front of the face and difficulty in gas dispersion. As a result, the face spalls, the roof exposes and the gas accumulates in the gob. With the continuing advance of the face and increase in area of overhang, the stress in the hard roof will eventually exceed its ultimate strength and cause a large area of caving, followed by quick release of energy concentrated in the roof and coal seam, which may cause rock bursts and other dynamic disasters in the mine as well as serious equipment damage and casualties. Therefore, the hard roof becomes one of the main factors causing rock bursts at the face.Hard roofs in China varies in conditions. It ranges from dozens of meters to hundreds of meters in thickness. However, coal reserve under hard roofs accounts for about 1/3 of the total reserve; moreover, nearly 40% of the fully-mechanized coal mining panels are those with hard roofs and more than 50% of the mining areas are associated with problems of hard roofs. Aiming at this problem, researchers at home and abroad have proposed many solutions, e.g. coal pillar support, strength weakening and forced caving, to prevent rock bursts caused by hard roof. These solutions have been employed in some cases with good results. However, due to the variability in geological conditions of mining and hard roofs, the application of the above solutions is limited."

Jan 1, 2015

By Kathleen M. Kowalski

This research explores the emergence of leadership in a crisis situation. The study by the U.S. Bureau of Mines focuses on three underground mine fires and the resulting evacuations. The subjects for this study are 48 coal miners, who evacuated the mines as part of eight escape groups, The subjects described their escape during an open-ended interview. Data were coded according to: (a) evidence of leadership behavior, (b) evidence of lack of leadership behavior, and (c) characteristics of the individual in each group who led the subjects out of the mine. During analyses, attributes of the leaders, who facilitated the escapes, were noted and compared as were instances of lack of leadership. The structure of the group leadership before the crisis was compared with the reality of the leadership during the crisis. Some groups experienced an apparent breakdown of leadership during their escape, while others witnessed the emergence of leadership. Consensus characteristics of the leaders, who emerged during these crises, are discussed and generalizations drawn. Research into leadership during emergency escapes is needed to provide information for training in prevention, escape, and rescue. The authors suggest questions for further investigation and topics for further inquiry into the area of leadership evolvement during crisis.

Jan 1, 1994

By C. W. DeLong, L. L. Farnham, L. A. Stewart

This paper is one of a series covering mineral resources of the Nation . It describes briefly most of the known manganese deposits of eastern Arizona , which for the purpose of this report includes the counties of Navajo , Apache , Gila, Graham, Greenlee , Pinal , Pima , Santa Cruz , and Cochise . With few exceptions , these descriptions are the result of field examinations by the writers . Work on this paper was begun in May 1956 , and in the following 18 months 151 deposits were examined . The distribution of the deposits by counties is as follows : 1 in Navajo , and 1 in Apache , 37 in Gila , 4 in Graham, 13 in Greenlee , 25 in Pinal , 13 in Pima , 12 in Santa Cruz , and 45 in Cochise . In surveyed areas the locations of the deposits are described by section , township , and range and in unsurveyed areas , by approximate projections of these subdivisions . The township and range numbers refer to the Gila and Salt River base and meridian . The history, production, ownership , geologic setting , and mining methods used are discussed for most of the deposits that were visited . Probably , some occurrences have been overlooked , but all of the principal ones have been examined . Ore dressing studies were made of typical ores from several of the larger districts . The work was performed in the laboratory of the Bureau of Mines Tucson Metallurgy Research Laboratory . The results of these studies are given with the descriptions of the deposits from which the samples were taken .

Jan 1, 1961

By Dzianis Proshchanka, Yoshi Izumi, Koji Mitani, Ayuna Kitaura

"A new pile driving and drilling navigation system has been developed. It utilizes the commonly used surveying total station, combined with an innovative reticle. Conventional crosshairs have been replaced by a concentrically circular reticle called Baum. It allows for easily performed measurements of central axes of cylindrical objects such as piles, chimneys, electricity poles, etc. This provides several significant advantages compared to other existing systems. It is cost-effective as only one operator is required to control deviations in positioning and inclination. Furthermore, repetitive reinstallation of the instrument is not required for every pile driven or hole drilled. It is also a safer method, as workers have no need to be near a pile driver or drilling machine to perform the measurements. With Baum Station, necessary measurements can be performed away from the actual work area. Moreover, it is highly accurate with real-time solutions, as three-dimensional orientation information for the pile/drill is obtained simultaneously with the pile being driven or the hole being drilled. This allows for the highest levels of precision-control and correction to minimize eccentricity of the intended center positioning.INTRODUCTIONBackgroundIn foundation construction for structures, pile foundations are widely used for deep bearing strata. There are two patterns to driving piles: vertically or obliquely to the ground. The shapes of the piles are normally cylindrical. Vertical pile foundations are employed as the foundations of many structures due to their high workability. There is a problem however, which is that this method does not bear measurement data as construction accuracy is visually checked. On the other hand, tilted pile foundations are rarely employed because it is too difficult to ensure construction accuracy. In addition, commonly used percussion methods create noise and vibrations when the piles are hit, while there are advantages that thinner piles are available, ensuring earthquake-resistance, as tilted piles curb horizontal displacements of structures, which may be caused by earthquake ground motion. However, current requirements of cost reduction bring professional attention to tilted pile foundations, which can be driven reasonably and economically with much research of tilted piles having been carried out to improve their capacity. Also, a method of screwing piling has been developed, which produces small amounts of noise and vibrations. This method has solved tasks of workability and environmental burdens, and is becoming more and more common. However, there is a necessity to develop a method to accurately measure angles of piles’ axes in order to drive piles into the ground with appropriate angles. It is also expected to find out a way to control construction information, such as correction amount and driving record."

Jan 1, 2017

By G. R. Waters

"The technology behind industrial applications such as Hydrometallurgy continues to evolve, as do the corresponding regulations and specifications that ensure the safety of workers and the environment. Valves make up key aspects of this technology, and often represent the single point of failure for entire operations. More often than not, the valves being used in Hydrometallurgy applications are known as Severe Service Valves (SSVs) due to their ability to withstand the extreme conditions. Most experts agree that SSVs are identified by applications, and that these applications are challenging to the valve’s ability to provide a minimum acceptable level of performance over a minimum acceptable duration. The Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry has designated Ross Waters, President of CGIS, as Lead to the Task Force put in place to determine the minimum requirements a valve needs to be able to perform to when faced with extreme conditions, whether from pressure, temperature, toxicity, solids, or usage. This paper serves to determine what the minimum requirements are for SSVs in Hydrometallurgy applications. It will draw on five decades of industry experience from one of Canada’s leading valve experts.INTRODUCTION Severe Service Valves Severe Service Valves (SSVs) mean different things to different people. Until today, defining SSVs had little if any global agreement or recognition. That is about to change as the Manufacturers Standardization Society (MSS) has accepted an application to produce a Standard Practice so defining them. This paper provides information about the selection of SSVs in all industries but focusses on metallurgical processes and applications and offers examples to illustrate the successful and unsuccessful use of these valves. All of this with the purpose of raising the awareness of the industry on all sides, from the suppliers and manufacturers, specifiers and to the users and owners of them. It also supplies tools to understand where and why to separate SSVs from general purpose or commodity valves (GPVs). SSVs are often identified by applications, and these applications are challenging to the valve’s ability to survive. Within these applications the elements that make the service severe are being analyzed, quantified and qualified. From this, we expect to offer objective and repeatable definitions and guidance to improve the experience of SSVs, reduce unnecessary costs, provide longer service life and process runs, improve safety and reduce environmental issues."

Jan 1, 2017

This publication is designed to be helpful in promoting health and safety in tunneling and related operations. The format has been selected and arranged to provide a condensed guide for safety personnel, inspection and investigative agencies, design and project engineers, and others responsible for the health and safety of workmen. All the precautionary measures recommended are based on actual conditions observed, from investigations of fatal or serious accidents, and from research conducted to find ways and means of alleviating hazards and unhealthful conditions. Many of the recommended rules are included in State laws and in the general safety requirements of the construction industry. Explanatory, descriptive, and qualifying information has been largely omitted in this publication to keep basic data in more useful and compact form. Included in the appendixes are special precautions for gassy (methane atmospheres) tunnels and tunnels where petroleum products are encountered.

Jan 1, 1968

By Richard S. Fowkes

Advanced technology, including automation and computerized information systems, is being adopted in mining at an ever-increasing rate to improve safety and productivity and to decrease overall costs. This U.S. Bureau of Mines report focuses on the human factors issues related to advanced technology. Among the significant facts discovered were the following: Experts studying tile design adoption, and implementation of new technology have stated repeatedly that human factors specialists should be involved from the early planning stages, through design and fabrication, and up to and during production, since human factors has been consistently identified as the biggest obstacle to the efficient utilization of new technology. Also, middle management is generally the greatest obstacle to the adoption of advanced technology, this technology can give rise to worker alienation, boredom, stress, job insecurity, and a sense of isolation; training most of the present work force is more cost effective than hiring new workers; workers are willing to accept new technology if they are given a voice in its implementation; the social and the technical systems should be jointly optimized; and with the intro¬duction of advanced technology, the cognitive or mental, rather than the physical, aspects of human-machine interaction must be emphasized.

Jan 1, 1994

By E. von Maltitz

IN his highly interesting paper on "Piping and Segregation in Steel Ingots,"1 Prof. Howe emphasizes the effect of successive phases of internal pressure in the ingot in the evolution of gas, and the consequent formation of blow-holes. From his statements in other places, it may be inferred that he does not here intend to ignore the other variable factor, temperature, but rather to discuss this one more particularly. At all events, it is my purpose not to engage in controversy with Prof. Howe, but rather to contribute, towards the complete elucidation of this important subject which we all desire, my own views and experience. If, in doing so, I specially emphasize other factors than pressure, I need not be understood as denying what I do not think it necessary to discuss fully. Nor, in presenting my own original conclusions, need I be understood as claiming to be the first who ever reached or announced them. Many things are asserted or suggested upon inconclusive evidence; and to confirm such tentative propositions may be as valuable a service as to overthrow them. In the following passage, Prof. Howe adduces analogies, based upon the behavior of charcoal and of water, respectively, which seem to me questionable "In general, the. solvent power falls as the pressure falls ; and in general it rises as the temperature falls. Thus, to heat a solid, for instance charcoal, may expel part of its dissolved gas ; and a tumbler of water drawn cold from the faucet gradually evolves gas, as it stands and warms up on the sideboard." (p. 238.) Charcoal is a solid body, which has the property not only of absorbing gases in large quantities, but also of expelling the thus absorbed gases upon heating. A comparison between charcoal and iron as to the absorption of gases is scientifically not possible ; the gas-content of charcoal is partly due to the

Sep 1, 1907

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By J. Ning, T. Bu, J-Q. Jiang, L. Jiang

"In coal mining in China, the cutting height of the shearer in longwall faces is increasing. Owing to the increase of extraction height, the caved roof strata area is enlarged, and new issues are being encountered, such as determination of a suitable working resistance for the shield and control of the roof. Through field observation and theoretical analysis of the first longwall face with a height of 6.0 m in the Bayangaole mine, a three-stage structural model was developed. Stage I is defined as the period in which the lower immediate roof (LIR) caves into the goaf and is broken into irregular shapes of various sizes. Stage II is defined as the period in which the upper immediate roof (UIR) breaks and impacts the LIR. In stage III, the main roof breaks into blocks and then impacts the UIR. With respect to these three stages, a suitable method was identified for calculating the working resistance of the shield support for a super-great mining height longwall face (SGMHLW). Introduction and backgroundThe coal seams in the Shendong coalfield, located in the northwest of China, are characterized by low dips and large thicknesses and are thus suited for full thickness extraction. Since the mid-1990s, the Shendong coalfield has been developed into one of the largest in the world (Ning, Liu, and Tan. 2014; Ning et al., 2017). Recent developments in mining equipment have made it possible extract entire seams up to 5.0 m thick in a single cut. This method, termed the ‘super-great mining height longwall face’ (SGMHLW) method, has been widely adopted in the Shendong coalfield (Table I) (Ju and Xu, 2013; Peng, Li, and Zhou 2015; Zhang, Fan, and Ma 2011). According to some studies, sudden support-closure incidents often occur when using the SGMHLW method. The key to solving this engineering issue is to have a clear understanding of the structural characteristics and movement laws of the overlying strata. For instance, the load on the supports is related to the movement of the roof stratum as a response to the mining activities."

Nov 1, 2018

By Yichi Lu, Haydn N. G. Wadley, Douglas T. Queheillalt

"Using a 3-D ray tracing methodology combined with laser ultrasonically measured elastic constant data near the melting point, ultrasonic propagation in cylindrical single crystal bodies containing either a convex or a concave solid-liquid interface have been simulated and used to design new sensing concepts. Ray paths, wavefronts and time-of-flight (TOF) of rays that travel from a source to an arbitrarily positioned receiver have been calculated. Experimentally measured TOF data have been collected using laser generated/detected ultrasound on model systems with independently known interface shapes. Both numerically simulated data and experimental results have shown that the solidification (interfacial) region can be identified from ultrasonic transmission TOF data. Since convex and concave solid-liquid interfaces result in distinctively different TOF data. When TOF data collected in the diametral plane are used in a nonlinear least squares algorithm, the interface curvature has been successfully reconstructed and ultrasonic velocities of both the solid and liquid obtained. The reconstruction errors were found to be less than 5%.IntroductionMany of today's single crystal semiconductors are grown by variants of a vertical Bridgman technique in which a cylindrical ampoule of a molten semiconductor is translated through a thermal gradient, resulting in directional solidification and the growth of a single crystal, Fig. 1.1 It has long been recognized that during crystal growth the velocity and the shape of the solid-liquid interface, together with the local temperature gradient, control the mechanism of solidification (i.e. planar, cellular or dendritic), the likelihood of secondary grain nucleation/ twin formation (i.e. the loss of single crystallinity), solute (dopant) segregation, dislocation generation, etc. They thus determine the crystals' resulting quality.2-4 The solidification rate and the solid-liquid interface shape are also sensitive functions of the internal temperature gradient (both axial and radial) during solidification.5•6 This in turn is governed by the heat flux distribution incident upon the ampoule, the latent heat release at the interface, and heat transport (by a combination of conduction, buoyancy and surface tension driven convection, and radiation) within the ampoule. The solid-liquid interface's instantaneous position, velocity and shape during crystal growth are therefore difficult to predict and uncontrolled during growth, especially for those semiconductor materials with low thermal conductivity (e.g. CdTe).4-6 The development of technologies to non-invasively sense the interface position and shape throughout the vertical Bridgman crystal growth process has therefore become a key step toward developing a better understanding of the growth process, for enabling sensor-based process control, and thus ultimately for improving the yield and quality of difficult to grow semiconductor materials like CdTe."

Jan 1, 1997

By R. D. Currie

A study of the accident statistics in the coal mining industry convinces one that an organized effort must be put forth to prevent the vast destruction of human life in this industry . The fatality rate in Pennsylvania has not improved in the past several years and during 1928 it was higher than the average for the period 1916 to 1927 , inclusive . Although the accident rate for this State is less than that of the coal mines of the United States as a whole , nevertheless the rate is unduly high ; however , there are many companies which have exceptionally good records as regards both fatal and nonfatal accidents . A study of the methods used by some of these relatively good- record companies to reduce accidents in their mines shows that they exert an organized effort to prevent accidents , and that their safety organizations usually affect every employee in and about the mine from the highest official to the check boy . The chief executive must be actively and personally interested in accident prevention if real safety results are to be obtained ; when he shows this interest it is almost invariably reflected in the officials under him and throughout the organization . Safety organizations vary in form and are readily changed or adapted to the varying conditions found in the bituminous field . The companies whose organizations were studied in preparing this report are all getting good results , and it is their opinion that the safety organizations have been a big factor in obtaining these results . At their request the identity of some of the companies whose organizations were studied has not been divulged in this paper , but this does not affect the value of the information concerning their safety organizations .

Mar 1, 1931

By JOHN W. KOSTER, JAMES R. FLEMING

The following report is made through the Bureau of Mines as a result of the work under the cooperative agreement with the State geological survey and the engineering experiment station of the University of Illinois. It deals with the use of permissible explosives in the coal mines of Illinois, and is intended primarily to present to mining men the possibility of assuring safer conditions in mining through the use of these explosives. Twenty coal mines in Illinois were using these relatively safe explosives at the time this report was prepared. Of these, seventeen were in Franklin County, two were in Saline County, and one in Montgomery County. In these various fields experience had shown that although black blasting powder was a useful agent in breaking down the coal at the working face, yet it had given such conclusive evidence of its danger to life and property in causing explosions and mine fires that a substitute was sought and has been found in permissible explosives. Each coal mine in Illinois in which permissible explosives are used was visited and a study made of the problems involved. The report deals briefly with the dangers of black blasting powder now in such common use in coal mining. It discusses the development of permissible explosives and their introduction into Illinois coal mines and points out the characteristic differences between permissible explosives and black blasting powder. The present system of blasting and the most approved methods of using permissible explosives are described. Data are given to show that not only has safety and efficiency in these mines been greatly improved, but that the cost of explosives to the miner per ton of coal has been reduced, and that sizes of coal produced from permissible explosives compare favorably with those previously obtained at the same mines with black blasting powder. The successful use of permissible explosives in these Illinois mines as well as in many other mines throughout the country should aid in their introduction into a larger number of mines and bring about that degree of freedom from explosions and fires which should be attained in mining.

Jan 1, 1917

By Guocheng Pan

"Although many factors play roles in the estimation of recoverable reserves, smoothing effect and conditional bias are considered major geostatistical issues in the estimation. This paper introduces measures for smoothing effect and conditional bias, and provides insights into their relation to the estimation of recoverable reserves. Both smoothing effect and conditional bias are intrinsic to the information effect and kriging estimators. For a given level of drilling information, however, it is possible to identify the optimal search radius that minimizes conditional bias. Furthermore, it is also feasible to define variance correction factor for reduction of the smoothing effect from exploration block models. Both of these components are key to the accurate estimation of recoverable reserves. IntroductionThe accurate estimation of recoverable reserves is critical to decision making in different phases of feasibility study and mine planning. Much attention for improving the methodology of estimation has been focussed on the effect of the change-of-support (Parker, 1980; Dagdelen, 1996). For example, it is essential to make a volume- variance correction to the estimate of multiple indicator kriging (Hoerger, 1992). When the size of block, b, in the geostatistical model differs from that of selective mining unit (SMU), v, a volume-variance correction is warranted for the prediction of recoverable reserves.Most mining plans and decisions are made prior to the availability of high density blast-hole samples. In most mining operations, the true SMU grade Zv is unknown at the time of selection. Instead, the selection is based on the estimate Z v**derived from high density blast-hole samples within the deposit G. Nevertheless, the estimate Z v * of recoverable reserves in the stage of mine planning is derived from exploration data. At the end, the production result must be reconciled to the estimate Z v * . In other words, the selection is based on Z v** from blast-hole samples, while the final production figures are reconciled to Z v * from exploration drilling. For a given preselected cutoff grade z0, the actual mining panels will consist of the units having the estimated grade Z v** =z0 rather than the true grade Zv =z0. The difference between Z v** and Zv is usually of less concern."

Jan 1, 1998

By J. L. Henry

The development and status of technology for producing titanium from U.S. resource materials are summarized in this Bureau of Mines report. Commercially feasible processes and investigations of alternative procedures are reviewed in order to identify techniques that could make existing operations more effective or areas in which future research may lead to the development of new production methods. Procedures are described for producing concentrated titanium dioxide from starting materials such as sands, massive deposits, and mineral processing residues containing rutile, ilmenite, and perovskite; producing and purifying titanium tetrachloride from concentrated rutile, ilmenite, and titaniferous slags; reduction of titanium tetrachloride to titanium sponge metal using metallic magnesium or sodium; purifying and consolidating titanium sponge and scrap by arc melting or induction melting techniques; purifying sponge, scrap, and alloys by molten salt electrorefining; and electrowinning titanium from chloride salts.

Jan 1, 1987

By Lloyd A. Morley

This seven-chapter document is the first volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. After a short introductory chapter, Chapter 2 discusses the history of electrical use in mining and introduces "typical" mine- power-system arrangements. Chapter 3, 4, and 5 supply basic information on electrical theory, circuit analysis, and motors. Next, the Grounding and Distribution Chapters detail unique aspects of mine power systems. Elements of surface and underground use are included in all these chapters. An index concludes Volume I and is cross-referenced to both report volumes.

Jan 1, 1982

The purpose of this study is to formulate practical guidelines for active underground mining in close proximity to water bodies. This was accomplished through systematic completion of three phases of study: I) Collection and Documentation of Data; II) Application of Existing Guidelines to Case Histories of Previous Inundations; and III) Development of Recommended Guidelines for Underground Coal Mining Near Bodies of Water. Phase I of the study involved a worldwide data collection effort designed to obtain foreign and domestic guidelines for mining near water bodies, and accident records and case histories of accidental mine inundations. Within Phase II, existing guidelines were categorized and classified and then evaluated as to their effectiveness in precluding past inundations had they been in effect at the time of inrush. Advantages and disadvantages of existing guidelines were defined. Drawing on the broad data base established in previous study efforts, Phase III was directed at development of viable guidelines to promote the greatest possible coal extraction while precluding accidental mine inundation. Two levels of guidelines are presented; Level I Guidelines require little or no subsurface exploration on the part of the mine operator, while Level II Guidelines recommend various testing and investigative procedures to permit greatest possible mineral extraction. This report presents findings and conclusions of the study.

Jan 1, 1976

By D. Harrington

The primary objective of this paper is to discuss the hazards and furnish a list of recommendations for the safe operation of quarries and related works. They have been compiled from Bureau of Mines publications covering the safety experience of engineers before and during the year in the mineral industry,5 from a publication of the National Safety Council, Inc.,6 from explosives recommendations made by various explosives manufacturers,7 and from suggestions obtained from quarries visited. The second objective is to describe and illustrate safety devices, practices, and quarrying methods. The quarrying and related industries of the United States had a lower accident-frequency rate than either the metal- or coal-mining industry as reported for 1942.8 However, the quarry industry ranked eleventh in 15 major industries during 1942 in lost-time accident fre¬quency; metal mining ranked fourteenth and coal mining fifteenth.

Jan 1, 1950

By WILLIAM F. McMURRAY, James O. Lewis

The Bureau of Mines is investigating the technology of petroleum and its products, the investigation including well-drilling methods and the transportation, treatment, and utilization of petroleum and of natural gas, with especial reference to the prevention of waste and to increased efficiencyin the development of oil and gas resources in land belonging to or controlled by the Government. During. the winter of 1912-13 the enormous waste of the gas encountered while drilling for oil in the Cushing field, Oklahoma, called forth protests from various sources, and appeal was made to the President of the United States and to the Secretary of the Interior in behalf of the landowner and of the public in general. The facts were wanted regarding the amount of waste and the technical conditions that were responsible for practices causing it. An investigation was ordered and conducted under the direct supervision of the late J. A. Holmes, the first Director of the Bureau of Mines. R. S.Blatchley was sent to investigate the amount of waste going on in the Mid-Continent flelds.s In the latter part of March, 1913, J. A. Pollard and A. G. Heggem were sent to Oklahoma to study well-drilling methods with reference to the waste of gas from wells on Indian lands and to suggest means of preventing the waste of natural gas on such lands. Pollard and Heggem decided that the mud-laden fluid process, which had been used successfully for some years in Texas, Louisiana, and California was the method that would meet the situation most efficiently and economically. The method was accordingly demonstrated in Oklahoma. In 1914 Congress provided for the employment of six oil and gas inspectors to supervise oil and gas mining operations on lands of the Five Civilized Tribes in Oklahoma and to conduct investigations with a view to the prevention of waste. Positions under this appropriation have been held by William F. McMurray, James O. Lewis, Harry D. Aggers, Ralph R. "Weed,George W. McPherson, James C. Fowler, Louis W. Courtney, and Carl H. Beal, the technical work of these men being directed "byW. A. Williams, chief of the petroleum division, Bureau of Mines. After careful and impartial investigation of conditions in Oklahoma, these men also decided that the mud-laden fluid process was the one best adapted to prevent further wastes. In 1915 laws were passed by the State of Oklahoma that provide for the conservation of natural gas and oil, authority being given to the corporation commission to make rules and regulations and to employ agents to enforce them. After hearings and investigations, the corporation commission reached substantially the same conclusions as the Federal agents regarding the importance of the wastes and the best methods of conserving the gas. Technical Papers 66a and 68b were published by the Bureau of Mines in December, 1913, and January, 1914, respectively. Technical Paper 66 deals with the mud-laden fluid process in general and No. 68 with its application in Oklahoma. The interest aroused by these publications has been so widespread that within two years the first editions have been practically exhausted. Rather than reprint these publications, it has been considered advisable to replace them with the present report, which includes the results of more recent investigations. The methods of using the mud-laden fluid are an outgrowth of the rotary drilling system, which was developed in Texas and later employed in Louisiana and California. Some of the principles of the use of mud fluid had been observed and used to a limited extent for a long time in cable-tool drilling. So far as known it was first used successfully with a circulator and cable tools in the Coalinga field, California, in 1906,Harry D. Aggers, one of the contributors to this paper, working on the well. The part of the Bureau of Mines has been to call attention to its merits and to demonstrate its practical use in fields like those of the Mid-Continent.

Jan 1, 1916

By A Murphy

Mining plants and infrastructure, and the decisions made by their designers, can have large impacts on their environmental and social context, commonly referred to as the site or plant footprint. They can also be the source of constructive contributions to sustainable development when designers are enabled via the information, systems and tools to incorporate sustainability in engineering processes. A facility’s footprint and the project’s contribution to sustainability – economic, environmental and social aspects – are now key considerations in regulatory approval processes and are the fundamental drivers of support, or opposition, from the project’s stakeholders.Historically, plant and infrastructure designers have not been well integrated with the environmental and social professionals who are engaged to pursue regulatory approvals. Despite this, many objectives central to technical and process engineering have in fact contributed positively to a facility’s footprint and indeed its contribution to sustainable development. Examples of these objectives include increasing process and energy efficiency, and minimising the quantities of waste requiring disposal. With the framework of sustainability, mining plant and infrastructure designers are indeed at the forefront of incorporating sustainability into resource industry projects and are central to the process of obtaining regulatory approvals and ongoing stakeholder support. The process of incorporation starts with a shared understanding of sustainability and sustainable development, and continues with project processes that facilitate information and knowledge exchange throughout the project life cycle.CITATION:Murphy, A, 2014. Incorporating sustainability into mining plant and infrastructure design, in Proceedings Life-of-Mine 2014 , pp 637–646 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014