Search Documents

By ALBERT E. HALL, Arno C. Fieldner, Alexander L. Field

As a safeguard against excessive clinker troubles, specifications for the purchase of coal can be drawn to include the "softening" or "fusing" temperature of the ash. The value of such information has been recognized by the Bureau of Mines and has induced the bureau to investigab~ laboratory methods of determining the fUSIbility of coal ash, and the bearing of the results on clinker formation in fuel beds. The bureau realized that the fusibility of a mixture of oxides and silicates snch as is comprised in coal ash ,'aries according to the conditions under which tests are made, and that in the absence of any generally accepted method, no agreement is to be expected among tests made in differ«:-nt laboratories. Indeed, Marks a has recently called attention to differences as great as 3900 C. that were obtained with the same sample of ash by two different laboratories. Therefore if a fusion-temperature clause is to have any place in specifications for coal, a standard m('thod of t('sting should be adopted in order to insure comparable results by different laboratories and to obtain the softening or fusing temperature of the ash unde:'r conditions similar to those of a fuel bed. After a consistent method has been devised for obtaining comparable:' results at different laboratories, there will remain the correlation of these results with those from the burning of coal in furnaces before the value of fusibility tests in coal specifications can hE' finally determined.

Jan 1, 1918

By Edward W. Parsons

The explosive-anchored rockbolt was field tested in six mines where rock conditions varied from incompetent shale or mudstone through fairly soft sand-stone to firm sandy shales. The purpose of the testing was to document, under a wide variety of conditions and in comparison to other rockbolt anchors, the quality of the anchorage produced by the explosive-anchored bolt. In addition, the length, strength, and design of the explosive charge necessary to produce positive anchorage up to the yield strength of the weakest component of the bolt were determined. A l4-inch length beaded explosive charge was found to be suitable, in general, in relatively weak strata, and the length can be reduced in more competent strata. Of the 127 explosive?-anchored bolts tested, 118 bolts produced an evaluated anchorage in excess of 17,000 pounds. Only 4 of 43 expansion-shell bolts and 4 of 14 wedge bolts produced anchorage this good. In preliminary tests, properly coupled explosive-anchored bolts did not ignite an explosive gas mixture. Some minor phases included in the investigation were as follows: (1) effect of explosive-anchored rockbolt on surrounding rock; (2) effect of time on anchored bolts based on torque tests; (3) effect of submersion in water on rockbolt anchorage; (4) pull tests to higher loads; and (5) ignition tests.

Jan 1, 1965

By Frank E. Cash, Max S. Petersen

The use of safe equipment, safeguards, and safe practices in the mining and allied industries should reduce injuries and improve accident experience. The object of this report is to give to the mining industry, especially metal mining, a graphic pictorial description of some of the safeguards, equipment, and practices used and followed in the iron-ore mines of the Lake Superior district. Some of the subject material has been in use or has been established for many years, and some is relatively new. Some of the equipment was purchased commercially, and some was designed by the company employees and constructed in the mine shops. The photographs were taken by the personnel of the Health and Safety Division of the United States Bureau of Mines, primarily for use in the Metal-Mine Accident-Prevention Course of the Bureau of Mines. In general, they are arranged under the following headings or subjects: 1. Accident statistics. 2. Support of ground. 3. Hoisting and haulage. 4. Explosives. 5. Fires, gases, and ventilation.

Oct 1, 1948

Adolph Greiner, Seraing, Belgium:—I have nothing special to add to Professor Hubert's paper except to say that there are some little things that it would be well to have corrected when the paper comes to be published. In dealing with the thermal efficiency of the engine, you will find that the 29.84 per cent. was a very high one. Professor Hubert has forgotten those engines built under the Cockerill type, but he has referred to them in Appendix 11. At our works at Cockerill we have built 63 engines, giving 63,000 h.p., and the other companies who have received licenses have built 113 engines, making 103,000 h.p., and aggregating 176 engines and 166,000 h.p. Eight years ago I had the pleasure of giving to the Institute the results obtained up to that time. Since then a good many engines have been constructed. In 1898 I thought a blast-furnace producing 100 tons of pig iron would allow 3,000 h.p. Professor Witz and Professor Hubert show that with the same production of pig the new engines take 3,800 h.p. out of the gas. At present at Cockerill we make 700 to 800 tons of pig iron per day, and we hope to have 26,000 h.p. in a few years. At present we have only half of that in gas-engines, but we hope to have in five or six years all the gas out of these furnaces to the number of 25,000 or 26,000 h.p. Tom WEstGarth, Middlesbrough, England :—My contribution is not a paper in the ordinary sense of the word, because I am sure you will agree with me that what I have written is only supplementary to the other two papers. The notes are schedules of the larger-size gas-engines built by British engine-makers, of 500 h.p. and upwards. If you look at the schedules you will find that in England gas-engines have become quite ordinary motors for a good many purposes. It was at first thought that gas-engines were troublesome, and ill-

Jan 1, 1907

G. A. Moore—The tin-fusion method has been a very favorable possibility for many years. The authors apparently have settled the question that delayed the method for a long time by showing that no hydrogen is absorbed in the tin. This, of course, is very important. I want to make a few remarks concerning the absolute accuracy of analysis, which must be the final basis for deciding among the various methods. From the figures in the paper, there seems to be some re-maining slight discrepancy on the actual amount of hydrogen present in various samples which may be presumed essentially identical. (This is of the order of the precision of individual analyses but appears in averaged results.) From the analyst's viewpoint, the tally of hydrogen content can be regarded as occurring in three portions. First is a large portion which comes off easily and automatically during sample storage and later on heating in the apparatus. This is fairly easily analyzed. Second is an item which may be either positive or negative in the tally sheet. In warm or hot evolution, this is a portion which, in practice, can never be re-

Jan 1, 1951

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

Recycling has become an important part of the lithium-ion battery (LIB) life cycle due to the growing demand for energy storage in applications like electric vehicles and renewable energy. Recycling spent LIBs provides a secondary source for strategically scarce metals, like lithium and cobalt, helping to reduce the environmental impact of LIBs. Organic acids have been proven to be effective lixiviants with the benefit of reduced environmental impacts, amongst which citric acid has shown to exhibit similar extraction performance when compared to mineral acids. Leaching LCO and NMC batteries with 1.5M citric acid and 2 vol.% H2O2 at 95°C, 20 g/L for 20 minutes achieved 93% Al, 90% Co, 96% Li, 94% Mn and 94% Ni dissolution. The strong chelating property of citric acid affects the separation of the metals, providing unique extraction opportunities. The first extraction uses 12 vol.% D2EHPA at a pH of 2.5 and O/A ratio of 2 to separate 96.4% Mn and 100% Al from the PLS in two counter-current stages. Stripping the loaded organic with 1.25M citric acid at an A/O ratio of 3 allows for up to 91% stripping of the manganese in a single stage. The second extraction then separates 96.5% Li from the PLS in three counter-current stages using 20 vol.% D2EHPA at a pH 5.5 and O/A ratio of 5. The raffinate remaining after the second separation contains 48.4 wt.% Co and 50.3 wt.% Ni. Keywords: Hydrometallurgy, lithium-ion batteries, metal recycling, citric acid, solvent extraction

Jan 1, 2020

By F. B. Petermann

The Bureau of Mines conducted electric furnace smelting tests on sintered flotation concentrate and siliceous log-washed are. The flotation concentrate was derived from the Maggie Canyon deposit of the Artillery Mountains area, Mohave County, Ariz., and contained, before sintering, 35.6 percent Mil and 19.4 percent Si02 + A1203. The log-washed ore was from the McGregor deposit of the Artillery Mountains area, Mohave County, Ariz., and contained 31.2 to 33.6 percent Mil, 19.5 to 27.6 percent Si02 + A1203, and 2.5 percent Pb. This work was undertaken to determine the most effective smelting technique for producing standard products from such nonspecification ore and concentrates. The objective was to collect data, using a small furnace, which would be reasonably accurate and permit extrapolation to large-scale practice for comparing with results on specification-grade are.

Jan 1, 1962

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By T. L. Johnston

A review of technical literature of the last quarter century discloses that much experimental work has been carried on in an effort to develop commercial processes for making sponge iron. In addition to the work that has been recorded, other work has been done the results of which have not been published. The degree of success or failure of these investigators does not detract from the fact that the problem has its challenging aspects and practical possibilities that encourage further investigation. The purpose of this report is to record information derived from recent experimental work that .had its 'objective the development and demonstration of one method of producing sponge iron. Work of other investigators was studied and applied wherever possible.

Jan 1, 1948

By D. Harrington

For many years the Federal Bureau of Mines-in cooperation with other agencies-has been making investigations and compiling and publishing reports and statistics on accidents in the various branches of the mineral industry.4 Its assistance has been enlisted also in health, safety, and ventilation problems' incident to the driving of many large tunnels in the United States in recent years. As part of this work the Bureau has compiled considerable statistical and other information on accident experience in the tunneling branch of the heavy-construction industry. It has always been difficult to obtain up-to-date information on tunneling methods and tunnel accidents. Published accounts of tun¬nel construction furnish much interesting material of engineering, historical, or fiscal value, but usually little or no attempt is made to discuss and critically analyze the means taken to preserve the health and life of employees.

Jan 1, 1941

By Almon F. Robertson

This is one of a series of reports describing investigations made within the Missouri River Basin in Montana by mining engineers of the Bureau of Mines, Minerals Division, Region II. The primary purpose of these investigations is to provide basic information to agencies of the Department of the Interior and other agencies concerned with the planning of power and other water developments in the Missouri River Basin. This report contains only such factual data as have been authorized for public distribution. Special precautions have been taken not to reveal any information or data considered to be confidential. The field investigations for this report were made during the fall of 1948 and the summer of 1949. Virtually all of the known metallic mineral deposits and some nonmetallic (industrial) mineral deposits within Judith Basin County were investigated. Most of the mines and prospects have been inactive for many years; most of the old underground mine workings now are inaccessible or only partly accessible. Consequently, much of the information on many of the mines and prospects necessarily has been obtained from available U. S. Government and State publications and from owners and local residents.

Jan 1, 1951

By Robert M. Becker

This report (the second in a series of five) presents the mathematical development in extending the theory of sample reliability from a sample consisting of a fixed number of items to a sample consisting of a fixed amount of items. Examples of a fixed amount of items per sample are samples consisting of a fixed weight or a fixed volume of unequal size particles. The probability distribution functions (those here called the compound binomial and compound multinomial functions) are developed from fundamentals. Their distributions are generalized to include some measured characteristic of the items. Infinite population moments are derived from moment-generating functions, while finite population moments are developed from corresponding infinite population moments using the finite probability operator defined in part 1 of this series.

Jan 1, 1964

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By R. M. Becker

THIS IS a progress report on a study of the application of statistical practice to mine and mineral sampling undertaken by the Federal Bureau of Mines to provide sound theoretical and practical data for use of the mineral engineering professions. One of the problems in mine sampling is determining the reliability of the results. For certain types of sampling data (random data) the reliability of the results can be stated mathematically. For other types of data there is no known means of quantitatively expressing reliability. In applying measures of reliability to a set of random data, some knowledge or assumption of the characteristics of the particular data is necessary. In many fields these characteristics are well known. However, in mining, where the data are in assays, these characteristics are not well known.

Jan 1, 1961

Explosives identification tagging refers to the addition to explosives, during manufacture, of coded microparticles that can survive detonation, be recovered and decoded, and allow the explosives to be identified and traced to the last legal possessor as a result of distribution records kept of the coded tagged explosives. This study seeks to prepare the way for National implementation of identification tagging of all dynamites and cap-sensitive slurries (also known as water gels) by resolving technical issues and by developing a plan for pilot testing of the program. It is presented in two volumes: Volume I, National Implementation Model, and Volume II, Pilot Test Plan.

Jan 1, 1977

The Full Scale Model Roof Bolt Test System described herein was designed, fabricated, erected, and installed by MSA Advanced Systems Division for the U. S. Department of Interior, Bureau of Mines, Spokane Research Center. It was furnished under USBM Contract No. 50271014 and Modifications. The test system is intended for use by the Bureau of Mines to run comparison tests on roof bolt systems. The mine entry cross section is made from special concrete pillars and roof slabs. They are constructed within a steel beam frame with hydraulic operated cylinders to apply loads that simulate the action of mining overburden. The frame is designed so it can be disassembled for replacing the concrete in subsequent tests. A computer and data acquisition system is furnished to control the load application and measure and gather data.

Jan 1, 1979

By Frank Pepe, Nestor Garavelli

The 2023 Rapid Excavation and Tunneling Conference (RETC) will be held in Boston, MA and will include the presentation of 133 papers divided into 20 technical sessions during the 3 day conference that were selected from over 200+ papers that were submitted to the committee. The selected papers are included within this book to provide a comprehensive recap of the conference while also providing a source of reference for contractors and engineers in the future. The selected papers will include contributions from all divisions of the tunneling industry plus risk management and best contract practices. Boston is known to the tunneling industry for its complex and difficult tunneling history, specifically of recent memory the Central Artery/Tunnel Project also know as the “Big Dig” of the 1980s and early 1990s. The selection of Boston as a host city was fitting from a historical perspective and as avenue for the city to present its upcoming tunnel projects. RETC began in 1972 with the idea of sharing ideas, design and project construction experience, and new technology, between contractors, designers, owners and suppliers. The ability to provide a single location every other year for all facets of the tunneling industry to gather and discuss the aforementioned was and still is viewed as a way to help the tunnel industry grow. The lessons learned from completed projects, the advancement of technology which could be implemented into design and the presentation of new projects by owners/designers and contractors allows for the limits and complexity of upcoming projects to be expanded beyond our current capabilities. Our industry has never been as busy as it currently is, and we are seeing more future projects coming out for solicitation across all business sectors. With the good fortune that all of us have been blessed with one of the biggest challenges that we have been faced with is the shortage of future management on all levels for our projects including the labor force. We all want our industry to continue to grow and succeed, our most important assets are the people that we employ. Investing in the education and continued training of our work forces to be up to date with the latest technology and methods is the key to our success. This also includes develop, recruiting and mentoring of young students graduating college to join our industry so that we can all continue to grow. We hope that all those attending the conference will have the ability to attend as many sessions as possible and to expand their network within our industry. As in past years, scholarship students will be in attendance and we encourage all to offer these students an opportunity to visit jobs, attend learning sessions or future internships to expand their interest in our industry that needs an injection of young engineers to contribute and lead our future Rapid Excavation and Tunneling Conferences. The program chairs wish to thank the session chairs, co-chairs, authors, and other members of the RETC Executive Committee for their dedication to this conference. Last but certainly not least, we give special thanks to the SME staff for their hard work and enthusiastic support in making this conference possible.

Dec 1, 2023

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and, liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise eight be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and. removing the disintegrated clay particles from wells after the perforated pipes have been inserted. Mechanical methods for removing mud sheaths are quite satisfactory, but prompted by tie request of certain operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions.

Jan 1, 1934

By A. H. Harvey, M. Delangen, A. D. Fernie

"A large-scale expansion to Pacific Coast Bulk Terminals Ltd. has now been completed and placed in operation. The original plant, built approximately eight years ago, consists of the direct rail-car to ship transfer of bulk commodities. The extension includes additional rail-car unloading, a transfer house system for directing commodities to storage or ship, major storage and reclaim facilities, a second shiploader and a second deep-sea berth. In addition to the facilities for overseas shipments, a wood-chip loader and a barge berth have been installed for domestic shipments of wood chips and, occasionally, for other local commodities. The design considerations imposed by the nature of the products to be handled are covered in this paper."

Jan 1, 1969

By W. W. Odell

The results of the 1921 cooperative experiments conducted by the U. S. Bureau of Mines and the University of North Dakota at the University mining substation plent at Hebron , North Dakota , pointed clearly to certain definite dep ficiencies in the schemes hitherto developed for benefiting and utilizing lignite . First The apparatus used in the carbonizing process or used to produce carbonized lignite suitable for briquetting is too costly , that is , the cost per ton day of residue made is too high . Second - The depreciation of the carbonizing appara tus is too high . Third The carbonizing apparatus can not be operated intermittently without seriously damaging it and impairing its efficiency of performance . Fourth Too little attention has been given to the possibility of using at least a certain percentage of the carbonized lignite directly in suitable stoves and furnaces without briquetting or other treatment . Accordingly , consideration was given to the design of an oven that could be built at a mine without the importation of highly skilled and specially trained construction men , erected at a low first cost , readily kept in a state of repair , operated at a rela tively high capacity and put into operation or shut down at will without seriously damaging the brickwork . The need of such an oven was appreciated also by the University of North Dakota and a cooperative agreement was made to build and operate such an oven during the summer of 1921.

Feb 1, 1923