Search Documents

Uranium, discovered in 1949 at Rum Jungle, 40 miles south of Darwin, N. T., was mined and processed to U3O8 from 1954 to 1963 by the Territory Enterprises Pty. Ltd. TEP is a Government company managed by Conzinc RioTinto of Australia Ltd. During this period, the uranium oxide was sold under contract to the Combined Development Agency, a joint Anglo-American uranium procurement agency. When the contract terminated in 1963, more than 31/4 million pounds of uranium oxide had been delivered which had been mined from three open pits. Copper ores, found with the uranium, necessitated the addition of a copper circuit to the concentrator. Copper concentrates containing 12,981 pounds of copper were also produced. Rum Jungle was the largest single industrial enterprise in the Northern Territories and, as such, was an important economic and social factor in this sparsely settled tropical region. To stretch out the life of this enterprise for the above reasons, and with the added possibility that the uranium market might improve, the Commonwealth mined out and stockpiled 650,000 tons of ore containing 9.6 lb of U,O, per ton, which is sufficient to sustain the treatment plant at 200 tpd until about 1971. In the plant, uranium is recovered from solution by solvent ex- traction. Current output is being stockpiled pending suitable market conditions.

Jan 10, 1964

By A. G. Metcalfe

THE failure to detect any change in the thermal properties of cobalt at the Curie point would appear to indicate that the apparatus may have a limited sensitivity. The Curie temperature has been determined by direct methods to be 1121+3°CP and 1131°C.3 The specific heat has been determined many times'.' and weighted values are given in Table I. The allotropic transformations in iron and titanium, used by the authors to test the experiment method, involved a volume change of the order of 3 pct on going from the close-packed to the body-centered-cubic lattice. These energy changes are likely to be much larger than those involved in a diffusionless transformation from a hexagonal to a cubic-close-packed lattice. However, it has been pointed out that thermal observations are unreliable in the detection of phase changes when these are near a Curie point.' James 0. McCaldin and Pol Duwez (authors' reply)—The sensitivity of the present technique is limited to first-order transformations, so that gradual changes in specific heat, e.g., in the vicinity of Curie points, are not detected. Furthermore, the existence of first-order transformations with latent heats much smaller than those occurring in the known allotropic transformations of iron and titanium is, we agree, still pending.

Jan 1, 1956

By A. McLean, J. Hou

Waste slag is a major environmental concern within the metallurgical industry. In the steel industry, about 100 kg of slag is produced in making one tonne of liquid steel from iron in addition to that produced during ironmaking. The amount of slag from the steelmaking converter can be significantly reduced when charging hot metal with low phosphorus and sulphur contents. In this context, hot metal pretreatment is known as an effective means of preparing high quality charge material for the converter thus limiting the generation of residual slag during the steelmaking process. In the aluminum industry, about 2-4 tonnes of slag, including red mud from alumina production and dross from aluminum electrolysis and casting, are generated during the production of one tonne of aluminum. In recent years, reuse of waste slag from the aluminum industry is a topic that is receiving increasing attention. In this paper, the possibilities of using waste slag and by-products from the aluminum industry as a refining flux in the steel industry are discussed. Several successful processes to convert waste materials from the aluminum industry to steel refining fluxes are described. Some theoretical aspects of using calcium aluminate based flux for desulphurization are outlined together with results obtained from laboratory experiments on sulphur removal from hot metal. By intelligent use of waste materials, the disposal of solid waste from the metallurgical industries can be reduced.

Jan 1, 2004

By M. S. Janssen, J. L. Taylor, M. A. Ford, E. B. Viljoen, H. A. Simonsen

The Stilfontein and Buffelsfontein Gold Mines, near Klerksdorp in the Transvaal, had accumulated a large amount of uranium-containing residue and, when the price of uranium rose in the 1970s, consideration was given to the possible recovery of this uranium. Preliminary tests showed that concentration of the uranium prior to leaching would not be economic. However, the pyrite in the residue could be concentrated by flotation, and the flotation concentrate could be roasted to pro¬vide both enough acid for leaching the uranium and a calcine from which the gold could be recovered. The feasibility study showed that a uranium operation of 270 kt per month would be most economically attrac¬tive, and a plant of that size was accordingly designed and built. In the first six years of its existence, the plant treated over 20 Mt of residue and produced about 3,5 kt of uranium oxide. During that time, the plant was con¬tinually being improved to make it more reliable and cost-efficient. This paper analyses the operation of the plant during its first six years from the viewpoints of its mechanical, process, and economic performance. The criteria on which the selection of the process was based are reviewed and compared with the actual performance of the plant, emphasis being placed on the leaching, solid-liquid separation, recovery, and purification stages.

Jan 1, 1987

By Walter G. Steblez

The countries of Eastern Europe are former members of the Council for Mutual Economic Assistance (CMEA). Geographically, they are located in Central Europe (Poland, Hungary, Czechoslovakia) and Southeastern Europe, largely in the Balkans (Yugoslavia*, Bulgaria, Romania and Albania*). It is important to remember that all of the countries of Eastern Europe had central planning imposed on them by the Soviet Union during the years following World War II. "Stalinist" policy for industrial development had three important tenets: • central economic planning, or a nonmarket-based command economy with administratively set prices; • economic priorities that stressed the development of heavy industries such as mining, metallurgy (steel) and heavy machine building; and • self-sufficiency at all costs, which was aimed at abolishing reliance on the world capitalist market, or reducing it to a minimum. Essentially, the system of industrialization that was used in the Soviet Union in the 1930s and 1940s was imposed on Eastern Europe. Organic market economic development in Eastern Europe ceased during this period. The flaws of this experiment became apparent when mineral processing facilities were set up in many areas of Eastern Europe that did not have reliable resources. Poland, Hungary and Romania are good examples of this situation. The Soviet Union became the principal supplier of iron ore and other minerals and mineral fuels, not only to these countries but to the Bloc as a whole.

Jan 1, 1992

When Australian voters elected a Labor Government in March 1983 the value of the Jabiluka uranium deposit as an asset of Pancontinental Mining Limited effectively evaporated overnight. The day before the election, Jabiluka was Pancon's principal asset, with the Company's 65% stake in the deposit having a market value of the order of $US1 billion. This value had been set by an agreement reached with a potential customer, who was prepared to pay $US150 million for 10% of Jabiluka. The months before the election had been the culmination of ten years of unremitting effort to bring what was then the world's largest reserve of high'grade uranium ore into production. These efforts had included two and a half years of negotiations with the local aborigines, as well as exhaustive environmental studies and conceptual mine planning. All domestic approvals required to develop the Jabiluka deposit had been given to Pancontinental and marketing efforts had successfully placed about 50% of the expected uranium production with overseas utilities. It appeared that Jabiluka was about to emerge as one of the world's great mining enterprises. The election of a government with an anti-uranium policy stopped Jabiluka dead in its tracks. Pancontinental's largest asset had effectively become worthless and the Company appeared to be facing a bleak future.

Jan 1, 1987

THE Institute assembled in the Hall of the Boston Natural History Society on Tuesday evening. Dr. T. Sterry Hunt, of the Boston Institute of Technology, after a brief address of welcome to the Institute, read an introductory paper on the Geognostical History of the Metals. President Raymond responded to the welcome of Dr. Hunt. The following names were then presented to the Institute, with the recommendation of the Council, for election: Adams, J. M., . . . . . . Silver City, Idaho. Daggett, Ellsworth,. . . . . Salt Lake City, Utah. Geist, Alfred W., . . . . . Boston, Mass. Hays, Dr. S. Dana, . . . . . Boston, Mass. Heinrich, Oswald J., . . . . Midlothian, Va. Johnson, J., . . . . . . Braidwood, Ill. Leckie, Robert G., . . . . . Actonvale, Canada. Lyman, Edward, . . . . ' . Troy, N. Y. Maltby, William, . . . . . Braidwood, Ill. Nichols, Lyman, Jr., . . . . Bbton, Mass. Ordway, Prof. J. M., . . . . Boston, Muss. Rand, Theodore D , . . . . . Philadelphia, Pa. Richards, Prof. Robert H., . . . Boston, Mass. Roclrwell, Prof. Alfred P., . . . Boston, Mass. Roepper, Charles W ., . . . . Bethlehem, Pa. Schulz, A. von, . . . . . Central City, Colorado. Singer, William F., . . . . Pittsburgh, Pa. Spillsbury, E. G., . . . . . New York. Wells, Calvin, . . . . . . Pittsburgh, Pa. The session concluded with the reading and discussion of a paper, by Henry Engelmann, On the Mines and Ores of the Little Cottonwood Canyon, Utah. The second session was held on Wednesday morning, when the following papers were presented : On the Midlothian Coal Mines, by Oswald J. Heinrich. On the Probable Existence of Microscopic Diamonds in California, by Prof. Benjamin Silliman.

By S Totsuka, P Ortiz, E Prokkola

Electrochemical polarisation techniques can be successively applied to maintain clean surfaces in process environments. The applications are the result of extensive knowledge of the electrochemical nature of process environments, an innovative approach to problem solving and shared æcan doÆ attitudes between the supplier and process owner. Initial identification of suitable applications is based on over 20 years of process and electrochemical experience. The technologies discussed in this paper include Electrochemical Anti-Scaling [EAS], Electrochemical Protection Systems with both anodic [EPSA] and cathodic [EPSC] protection and Electrochemical Flocculation [EF]. Examples of industrial applications are reviewed. Good examples of metallurgical processes which can benefit greatly from an advanced electrochemical treatment are the wet processes involving precipitation, crystallisation and evaporation. Eliminating corrosion and scaling which would otherwise cause process disruptions and quality problems can make a big difference in process profitability. Clear advantages in both cost efficiency and environment friendliness are easily demonstrated. Continuous processing with minimum downtime is one clear advantage. In comparison to the use of corrosion inhibitors, anti-scaling agents and flocculants, the electrochemical polarisation does not increase the environmental load from the process as no additives of any kind are used. In most cases the cost benefits from pro-actively keeping surfaces clean with the help of advanced electrochemistry are substantial when compared to traditional re-active methods and other active treatments.

Jan 1, 2004

GRAHAM BRIGHT,* East Pittsburgh, Pa.-Bee-hive coke ovens are usually located at the mines, where the gases from the ovens are not strongly objectionable because the communities are not thickly built up. The byproduct oven will naturally he located near centers of industry, to which the coal can be brought from different directions and desirable mixtures can be made; where also the byproducts can be readily marketed, while the gas can be utilized for industrial and domestic purposes. Not much thought seems to have been given to the gases escaping from the byproduct coke oven, which are more or less objectionable in thickly populated sections. When the byproduct oven shall have been more widely installed, this question is likely to become serious, and it will be necessary to apply remedies. May I ask what has been done, or is going to be clone, in this direction? S. A. Moss, ? Lynn, Mass.-One cause of escaping gas is that the gas exhausters do not supply the proper suction. If a satisfactory regulating governor is applied and the correct kind of gas exhauster is used, the trouble will be eliminated. J. I. THOMPSON,? Pittsburgh, Pa.-The hoppers Co. has made a careful study of the question of smoke prevention. The smoke caused by the operation of the byproduct coke ovens is infinitely less than that caused by bee-hive ovens.

Jan 11, 1918

By J. S. Hattrup

INTRODUCTION Tunnel boring machines in non-abrasive competent rock with little or no water have set new performance standards in the driving of tunnels. However, when the machines have hit blocky or running ground, they have encountered difficulties. The success of a tunnelling machine is usually due to a thorough geological investigation which accurately describes the rock conditions, a well designed tunnel support system, and a tunnel boring machine designed to cope with these conditions. In some cases machines have had to be modified in the tunnel after the machine had commenced boring, because geological conditions were not correctly anticipated before tunnelling began. The features described herein are not a panacea for all conditons, and some of them, like an auxiliary thrust system that thrusts off a precast invert segment requires pre-planning of work on the part of the contractor. CUTTERHEAD DESIGN Figure 1 shows typical cutterheads of ten to fifteen years ago. Note the large buckets and large openings between the buckets. These large openings were considered necessary to gain easier access through the cutterhead for cutter changes. The standard cutter in those days was an 11 inch or 12 inch cutter with small bearings, and was generally a delicate tool for the duty it was to perform. These large buckets would clog up if a formation with clay seams was

Jan 1, 1981

By Ora H. Rostad

Some gold production was obtained from placer deposits in Puerto Rico during the period of Spanish colonial rule, but most of the gold was produced prior to 1536. There had been no significant hard rock mining, other than in quarries for road metal or construction purposes or for raw materials to make cement, prior to 1954 when the government of the Commonwealth of Puerto Rico recognized that changes in the mining code were necessary to stimulate exploration for metalliferous ore deposits. The Puerto Rican Legislature passed an act (No. 6), which was approved on Oct. 6, 1954, that reiterated that the title to all "commercial minerals" is vested in the Commonwealth of Puerto Rico. The act provided for the establishment of a Mining Commission, stipulated the power% with which the Mining Commission was vested, and provided that no one may dispose of "commercial minerals" in Puerto Rico without a Commonwealth grant issued on its behalf by the Mining Commission. Act No. 6 also provided for prospecting permits, mining leases, and grants. The Mining Commission, by authority granted to it by Act No. 6, adopted regulations effective Nov. 21, 1957, relating to prospecting, leasing, and producing commercial minerals in Puerto Rico. Royalty rates were also specified for various types of deposits at different annual tonnage production levels.

Jan 1, 1991

EUGENE COSTE, ? Calgary, Alta.-Evidently in Argentine they have a petroliferous province just east of the Andes where very much the same conditions exist as are found on the east side of the Rocky Mountains and in the plains adjacent. It strikes me, though, that the same mistake is being made in Argentine in the exploration for oil as was made in Alberta, Canada; viz., drilling the wells too .near the seepages in the belt in the eastern part of the petroliferous province, too near the mountains. This same mistake was made in Alberta, with disastrous results; viz., only fissure production was found. The strata so near the mountains are tilted at a very strong angle, such as is described in this paper, and the dislocations are intense. On the other hand, we have found that when we get 100 or 200 mi. away from the mountains we get into oil and gas belts which are very prolific. So far our fields in Alberta have been gas, but in Wyoming, as you know, they get many thousands of barrels a day. I have no doubt that conditions in Argentine are exactly similar but that they have so far kept too near the mountains and that they want to explore the belts farther east to obtain better results.

Jan 4, 1919

Early efforts to control the dust necessarily produced during dry crushing operations, took the form of venturis at loading chutes and other places where dust was most evident. These venturis discharged to the atmosphere and for obvious reasons were not very satisfactory.Attempts to collect the dust drawn off by the venturis, using dry cyclones, were not successful, the cyclones catching only the coarser particles. Further, no satisfactory method of continuously discharging the dust catchment was evolved. Water sprays were also used, and will be referred to later.In 1940, a single discharge fan of 3,000-4,000 cu. ft. per minute capacity, was installed to draw the dust-laden air from the Symons crushers and ·screening sections with their attendant conveyors. Suction was through two 15 in. ducts which branched off into 10 off-takes situated over the conveyers at points of discharge from crushers and screens.A dry cyclone was installed in front of the fan, which exhausted into a bag-house.The cyclone suffered from the defects of the smaller units mentioned earlier. When the collected dust reached a certain level in the cone, no more collection would take place until the cone was emptied. This objectionable feature was overcome by introducing a jet of water ahead of the cyclone. The water and dust collected overflowed a weir and were pumped to the mill.

Jan 1, 1948

ALTHOUGH the mineral Stannite (Cu2S, FeS, SnS2 , also known as "bell 'metal" ore, tin pyrites, etc.) is found in various parts of the world, in only three iocalities has development proved it to exist in sufficient quantity to warrant the erection of treatment plants. Two of those mines are in New South Wales and one is an Tasmania. The writer will deal with the latter-the Conah mine, Zeehan, Tasmania, it being the most important and extensive occurrence so far worked. The Conah mine was first worked by a Tasmanian company for silver-Iead, and was fairly remunerative until the zone of secondary enrichment was passed through, when the lodes became too poor for further exploitation. During the time that the line was thus operated the stannite lode was discovered. It occurs in a graphitic slate, which, in common with the slates and spilites of the Zeehan field, is probably underlain by the stanniferous granite which outcrops two miles to the west. The Conah stannite lode is older than the galena lodes of the district, being faulted by one of the latter. Near the surface the lode was very rich.Shipments were sent out assaying 150 oz. of silver per ton, 20% copper, and 18% tin. An .apparently homogeneous sample of stannite, analyzed by the writer for the Tasmanian Geological survey, gave the following results:

Jan 1, 1915

By Wei Liu

A new process for extracting cadmium from the electric precipitated dust produced by ISP process was studied. A leaching rate of 89.1% of cadmium was attained by leaching the dust with NH3?H2O-(NH4)2SO4 system under the best leaching conditions: ratio of liquid to solid(l:s)=2.5, c(NH3):c(NH4+)=3:5, total concentration of ammonium and ammonia=8 mol?L-1, leaching time= 1.5h, temperature=35. The most troublesome impurity of lead could be deposited from the leached out solution automatically after put it static more than 15h when the total concentration of zinc and cadmium was up to 45gL-1 , and the final concentration of lead was 0.0047 gL-1, which meant 99% of it was removed. Metallic cadmium which contained cadmium more than 99% was prepared by electrowinning under the conditions: current density=750Am-2, total concentration of Cd2+ and Zn2+>25gL-1. The current efficiency was about 87% and the energy consumption for every ton of cadmium was about 548KWht-1. Main impurities of the metallic cadmium were copper and zinc and all of they could be got rid of in the following pyrometallurgical refining step.

Jan 1, 2006

By W. F. Baldwin

The timing circuit generally employed in Carter Reservoir Behavior Analyzers consists of a synchronous motor driven cam which actuates a microswitch. A mechanically actuated timer of this type has several inherent disadvantages, among which are the following: 1. The first time interval may not be of uniform length, depending on the exact position of the cam at the conclusion of a previous run. 2. The positioning adjustments on the microswitch lever arms are critical and require periodic readjustment. 3. The mechanical system is subject to wear which will ultimately impair its accuracy. It was therefore considered desirable to devise an alternate method which would eliminate these difficulties without introducing others that would be equally troublesome. This note describes the design of an electronic timing device which has been incorporated in the analyzer constructed by the Field Research Laboratories of Magnolia Petroleum Co. The electronic timer circuit is built around a simple neon glow tube relaxation oscillator, the complete circuit diagram of which is shown in Fig. l. The operation of the circuit is as follows: Condenser C, is charged to the critical firing voltage of the neon glow tube VR-75 by battery B1 through resistors R1 and R2. When the neon glow tube fires, the condenser C, is discharged, The charging cycle then repeats itself,

Jan 1, 1950

By Ahmad Hemami

A working code is developed to simulate the forces that are involved in the process of penetration of a bucket into bulk media during loading and excavation. The result of this work can be integrated with the simulation software that many manufacturers of heavy earthmoving machines introduce for training purposes. The simulator programs for machines such as backhoes, loaders, LHDs and the like, used for operator training, are usually only based on the kinematics of the machine. As a result, there is no indication of the effect of the medium when the cutting tool of such a machine touches the excavation material. This is like moving the machine in the air. Feeling the resistance force of medium to cutting by a bucket or blade during loading and excavation is more realistic, both mentally (by vision) and physically (feeling resistance in pedals and levers). The results from force simulation can be used by feedback in creating simulated resistance in these training gears, similar to what is done in flight simulators for aircrafts. In addition to serving for the above purpose, the results of this work can be used as a tool for examination and verification of the effect of a control policy for automation of loading and excavation of bulk media. So far no commercial product has been introduced that has such a capability, despite some extensive research on the subject.

Aug 1, 2013

By C. L. Schaidle

Computers and communications technology have revolutionized many industries. In earthmoving, this revolution has just begun. The major changes are still to come but are just around the corner. This article presents a vision of this upcoming revolution in the earthmoving industry. This vision includes basic communication, machine monitoring and diagnostics, job and business management, planning and operations, and machine control. For the industry to realize maximum benefits from the information age, it must have a vision of the future that is shared by technologists, machinery producers and miners. History of the information age During the 1970s, the information age revolutionized retailing, starting with the grocery business. By using bar codes and laser scanners, individual items were connected to the information world of computers and communications. Once this connection was made, the data on what an item was and where and when it moved became valuable information for inventory control and marketing. Not only was the information valuable, it was easy and inexpensive to collect and manipulate. The effort required to provide the consumer with the right product at the right time was reduced. Costs went down and customer satisfaction went up. But there were casualties of this revolution. Many inventory counters lost their jobs. There were also equipment casualties. Cash registers that could not interface with the digital world were discarded long before the end of their useful life.

Jan 1, 1994

[ ] (14) SCREENS: Description of Allis-Chalmers' complete line of vibrating screens for the mining industry is contained in a new 8-page bulletin. Primary scalping, secondary scalping, and conventional screens for wet or dry sizing and screens for heavy media separation are included. Also given is a typical fiowsheet showing how horizontally operated Low-Head screens are used in the sink and float process. (15) MILLS: Forty-six years of experience and 4000 installations throughout the world lie behind the seven basic types of mills illustrated in a recent bulletin from the Hardinge Co. Fields of application and materials handled in various installations are listed. (16) BLOWERS & COMPRESSORS: A brochure describing the manufacturing facilities and the axial and centrifugal blowers and compressors made by the Sawyer Bailey Corp. is now available. (17) LINATEX: The first catalog of the Linatex Corp. of America has been issued, outlining the advantages claimed for this special form of natural rubber, when used in corrosion, abrasion, and vibration resisting applications. (18) WIRE ROPE: Twenty-four pages packed with concentrated wire rope data is the way E. H. Edwards Co. describes a booklet which they are now making available. It was condensed from the Edwards general catalog to provide users with a concise guide to every important phase of wire rope production, maintenance, and use.

Jan 1, 1952

By E. G. Deane

THE CHAIRMAN (P. G. BECKETT, Globe, Ariz.).-The mining of large orebodies has in the last few years been such a big factor in the copper output of this State, and, in fact, of the whole country, I feel that we should have some valuable discussion this evening on the various mining methods described in the papers which are to be read; and I hope you will start a discussion on Mr. Deane's paper. J. A. EDE, La Salle, Ill.-I would like to ask whether, the timbers being left in, they have any fires owing to that fact? E. G. DEANE.-No, we do not. The timbers in the mat seem to lose life. I cannot tell you exactly what change takes place, but they do not burn readily. There is undoubtedly a chemical change in them-a change that makes them lose all strength. I , spoke of the strength of the sills. When we first started, we put in 4 by 8 sills, but those sills had no more strength in 6 months than a 2-in. plank would have. .J. P. HODGSON, Bisbee, Ariz.- I would like to ask Mr. Deane if the central supply raise in the- center of the block has been satisfactory; and also whether in extracting the ore they put small raises up so that wheelbarrows are not used in the stope?

Jan 12, 1916