Search Documents

By H Arvidson, V Chamberlain, R Marinho, B Parsons, T Rowl, M Noppé, M Mattera

With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.

May 24, 2023

By A. U. Miller

Protection against fire is a greater problem at a coal mine, than at an ordinary industrial plant. Generally mines are located in isolated districts and do not have the protection of city fire departments; consequently fire fighting aquipment must be installed by the mining company. Fire protection around a mine is just as essential as it is in the city.. and undoubtedly is more important if the fire should be underground where many lives would be endangered and all means of escape cut off. A surface fire can generally be attacked from any angle, but an underground fire can be attacked only as conditions will permit.. U. S. Bureau of Mines engineers have investigated many serious mine fires that undoubtedly could have been extinguished in incipiency if a fire extinguisher or fire hose and water had been readily available. In past years very little attention was given..to fire fighting equipment and organization around mines, but in recent years three gen a derde hange of opinion among many of those engaged in mining, and nearly all up-to-date mining companies now have some kind of fire protection about their mine Probably the first company in Illinois to install regular fire fighting equipment and effect a fire fighting organization at its mines, was the Madison Coal Corporation, which operates several mines in Illinois. The main office of this company is in Chicago and the general field office is at Glen Carbon, Ill.

Jul 1, 1930

By Y Potvin

Underground mines in Australia are progressively operating at greater depth, sometimes in conditions where mine induced stresses are very high. In such conditions, the seismic activity often becomes intense and violent and in response, mines must develop and implement a sound rock burst risk management strategy to continue operating safely.This paper discusses the latest techniques successfully used in Australian mines to mitigate the risk of rock bursts. In particular, the paper describes how the analysis of data collected from seismic monitoring systems can provide an understanding of the seismicity and be used for quantifying seismic hazards in the mine. Once an adequate understanding and assessment of seismic hazard has been achieved, the associated risk can be mitigated using different layers of protection.Strategically, modifying the mining method, the extraction sequence and/or the mining layout can alleviate the seismic hazard, but these solutions generally cannot be implemented rapidly. In the short-term, seismic risk can be mitigated tactically using an energy absorbing support system or to remove personnel from being exposed to rock burst damage by implementing exclusion zones.

Mar 21, 2011

By Y. Zhang, M. Yekich, C. Zhou, C. Jobes, J. Galanko, D. Tuchman, J. Srednicki, J. Carr

The continuous personal dust monitor (CPDM) is an essential instrument for working in hazardous environments, is used to monitor real-time coal dust exposure, and is mandated by the Mine Safety and Health Administration (MSHA) for underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) found that it is possible for electromagnetic interference (EMI) between a CPDM and a proximity detection system (PDS) to occur. Various approaches have been taken by researchers and manufacturers to address this EMI issue. Administrative controls were recommended to keep the CPDM six inches away from the wearable PDS device. Shielding pouches were made to contain the electromagnetic (EM) emission from the CPDM. Metal shielding was added to major EM emitting components. EMI filtering with large capacitors was introduced to mitigate EMI. Most recently, a novel magnetic-field-cancellation-based approach was developed and achieved remarkable results. In this paper, we provide a comparison between these approaches. The pros and cons of each approach are presented and discussed, so that mining device manufacturers and operators can best evaluate the technology and controls that improve the health and safety of mine workers.

Feb 1, 2023

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By J Seccatore, T Marin, M Cardu, G De Tomi, F Galvão, A Rezende, E Melo

Small-scale mining operations are characterised by a large variety of equipment availability and a high level of operational flexibility. Mine planning is usually scarce or absent in small quarries in Brazil, and mine management generally focuses on daily operations. As a result, analysis of the effects of unit operations, such as blasting, over the whole mining process is often neglected. The goal of the following project was to study the effect of production blasting on loading and hauling times, secondary breaking times and primary crushing times at the Experimental Mine of the Research Center for Responsible Mining of the University of São Paulo, Brazil. The operations analysed included blasts that performed:under the average operational standard, defined in this paper as Case 1according to quarry standards, defined in this paper as Case 2.In order to establish the effects of blasting on the downstream process, three key performance indictors were used:The time taken to load the truck, when there is the need for material selection. Due to the fact that we do not have an operational baseline, the increase in time cannot be established, meaning that we must content ourselves with comparing the mean time in each scenario.The average time used for secondary breaking machinery.The time required for the primary crusher to fully process the load of a single truck. The results obtained indicate correlations between the coarseness of the blasted material and these operational times. Solutions are suggested and evaluated for the improvement of the small-scale mining process.CITATION:Marin, T, Melo, E, Seccatore, J, Cardu, M, Galvão, F, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The effect of drilling and blasting performance on fragmentation in a quarry and time for loading, secondary breakage and crushing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 355–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By V

"Recent regulations, as well as a general aversion to central dust collectors within the Powder River Basin Coal user’s community, have created a need for an alternate method for eliminating airborne dust. This paper addresses the capital expenditure as well as the cost of ownership of an integrated point source air cleaning system in comparison to a central collection system. This assessment was conducted by comparing the cost to purchase and operate a central dust collection system and integrated air cleaner system on a typical multiple transfer point application. The central dust collector consists of a negative pressure blower, a series of filter bags, a collection hopper, a screw conveyor to place collected material back into the material stream, and a series of ducts to pull air and dust from individual pickup points. The point specific integrated air cleaners consists of a negative pressure blower to pull dust and air from an application point through a bag-less filter media located at the application point. The agglomerated material is then redeposited into the material stream at point of use without the need for ducting or a central material hopper. The assessment yielded a 54% reduction in capital expenditure and a 26% reduction in operating costs for the same application when using individual dust filters as opposed to a central system. In addition to the lowered cost, there are reductions in risk associated with the elimination of ductwork and the central containment enclosure for collected explosive dust. By the conclusion of this paper, the reader will have a better understanding of the quantifiable differences between a central dust collection system and a set integrated air cleaner systems. BACKGROUND Spillage has always been a problem in the bulk solids handling industry. As long as there have been conveyors, there has been spillage. Spillage is material that falls off a conveyor belt and creates a hazard in the environment around a conveyor belt."

Jan 1, 2016

By C N. Hatton, K Ward

Tailings operations are inherently reactive as operations personnel continuously contend with a concentrator reject feed (tailings) transient in physical and engineering properties, which places a constant constraint on capital and operational spending. It requires a unique skill set to manage the prescribed distribution of tailings under unenviable conditions. Enter the tailings operator, an oftenundervalued commodity and untapped resource that can provide benefits beyond the rigors of dayto- day operational support. Experience consistently demonstrates that skilled and committed operators can serve a vital function in the safe construction of a tailings storage facility. It takes a village to raise a tailings dam. An important part of this process is establishing a culture of operational accountability and ownership. Operator development training is nothing new. However, we find that many of the intrinsic operator skills are left unexploited, and an operator's experiential knowledge base and creativity are commonly overlooked and underutilized. With proper training and guidance, these skills can be harnessed, contributing to safe dam operations. Operator engagement, when properly facilitated, provides tangible benefits ranging from improved tailings engineering properties to reduced closure costs. One important benefit is helping transitioning tailings management from reactive to proactive. There are many processes involved in the reactive to proactive transition process. One element of that process includes engaging operators in the tailings management process and facilitating legacy ownership. The core of operational legacy ownership is measured and described using five-stage operator engagement rubrics. Levels of operator engagement are presented with a description of the incremental benefits of each stage. An important part of legacy engagement is providing the tools to operators necessary for managing the tailings. Therefore, the approach identifies specific methods used by operations personnel to control tailings distribution and in-place properties. The end goal of leveraging operator engagement is to facilitate committed ownership and transition tailings management from an inefficient, reactive process to an improved, cost-effective, proactive practice.

Jul 1, 2021

By David F. Gearhart, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

"Coal mine longwall gateroads are subject to changing loading conditions induced by the advancing longwall face. The ground response and support requirements are closely related to the magnitude and orientation of the stress changes, as well as the local geology. This paper presents the monitoring results of gateroad response and support performance at two longwall mines at a 600-ft and 2,000-ft depth of cover. At the first mine, a three-entry gateroad layout was used. The second mine used a four-entry, yield-abutment-yield gateroad pillar system. Local ground deformation and support response were monitored at both sites. The monitoring period started during the development stage and continued during first panel retreat and up to second panel retreat. The two data sets were used to compare the response of the entries in two very different geotechnical settings and different gateroad layouts. The monitoring results were used to validate numerical models that simulate the loading conditions and entry response for these widely differing conditions. The validated models were used to compare the load path and ground response at the two mines. This paper demonstrates the potential for numerical models to assist mine engineers in optimizing longwall layouts and gateroad support systems.INTRODUCTIONThe need for roof stability in coal mine longwall gateroads places significant demands on the gateroad ground support system. The variable loading conditions associated with the approaching longwall face can cause excessive ground deformations that need to be accommodated by the support system. In coal mines in the United States several different types of supports are used to maintain the stability of gateroads. The supports may include grouted roof bolts, cable bolts, and roof trusses as intrinsic support. Standing supports include timber cribs, engineered timber props, and various types of cement-based cribs. The intensity of support is governed by the expected geologic conditions and the expected stress changes that will occur during longwall mining. At present, the design of ground support for gateroads is largely based on local experience. In-mine trials are usually conducted when new support technologies become available or ground conditions dictate a change in the support system. The research reported in this paper has the objective to assist mining engineers in evaluating alternative gateroad supports and to design suitable support systems for the local ground conditions."

Jan 1, 2018

By D. R. Tesarik, T. C. Trancynger, W. G. Pariseau

The Davis detector cavern was excavated on the 4850 Level of the former Homestake Mine in the mid- 1960s to house a novel neutrino detector developed by Nobel Prize winner Dr. R. Davis. The original cavern was about 9.1 x 16.8 x 9.7 m high, excavated in a Precambrian amphibolite known as the Yates unit and enlarged in 2010. In 2009, the National Science Foundation selected the site for development as a national Deep Underground Science and Engineering Laboratory (DUSEL). This retrospective rock mechanics study of the Davis cavern is intended to inform design of the much larger caverns and laboratory rooms being considered for the same 4850 Level. Provision for rock mass variability, sequential excavation, jointing and wall damage from blasting are included in analyses that were done using two different computer codes and methods (FLAC3D and UTAH3). The results are in agreement with observations and show that cavern stability is indeed the case. The main conclusions are: (1) if conventional scaling of laboratory rock elastic moduli and strengths is done, then 0.25 and 0.50 scale factors are reasonable, (2) measured statistical and spatial variability in rock properties should be incorporated into geomechanical analyses to better reflect reality, (3) discontinuities (“joints”) are essential to reliable analysis of excavation safety and when properly taken into account eliminate the need for empirical “scaling” of laboratory rock properties, (4) major geologic features such as rhyolite dikes and breccia zones may be important to excavation safety at Homestake and should be explicitly represented in analyses and (5) quantifying wall blast damage is important to engineering design of underground excavations.

Jan 1, 2012

The need to hoist increasing loads from great depths is leading to the more general adoption of winders of the Koepe and Blair types. The trend has introduced a number of new problems in winding ropes, more particularly in the Koepe system where regular destructive tests during the life of a rope are not possible. Consequently, the importance of introducing non-destructive tests is much greater, especially so in the case of Koepe ropes used for deep winding where there are three major destructive fatiguing influences. These are rotational effects when a vertical rope is changed end-for- end each trip, the much greater range of stress to which the rope is subjected each trip as compared with drum winding, and the destructive effect of a high coefficient of friction between wheel and rope. A plea for a lower coefficient in the interest of better rope and tread life, substantiated by analysis, is made for Koepe winders operating at depth.Co-ordination of rope testing with general hoisting problems is stressed and the active participation of the Wire Rope Committee of the Australian Mineral Industries Research Association Ltd. in the promotion ofthe project is noted.The general introduction of a rope testing programme in Australia, personnel requirements and some local basic research in the subject to cope with future demands are considered.

Jan 1, 1967

By M. Reuter, C. Schuffeneger, T. Seppälä, L. Holappa

Reaction kinetics of solid-state reduction of chromite pellets (laboratory made and industrial) and lumpy ore was investigated by the thermogravimetric analysis (TGA) technique. Carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at both rising temperature and constant temperature in the range of 1450 - 1550°C. Scanning electron microscopy was employed to observe and analyse the structure and composition changes of the chromite samples. For the lab-made chromite pellets, the effects of particle size and bentonite addition on the reduction behaviour were studied. The pellet with smaller particle size gave a higher reduction rate. Bentonite addition had slightly negative effect on the reduction rate. When reducing industrial pellets, temperature and CO flow rate had positive influence on the reduction rate. Reduction of lumpy ore took place slower than reduction of a pellet. In all samples, chromite reduction proceeded longer in the outer part of the sample than in the centre part. The porosity of the chromite samples was determined before and after the experiments. The porosity of lumpy chromite increased significantly during the reduction. However, the porosity of lab-made chromite pellet decreases due to sintering effect. The reaction mechanism is discussed on the basis of experimental results and earlier investigations.

Jan 1, 2004

By B Cope, Y Churi

Roxgold was a small exploration company when it discovered the Zone 55 orebody at the Yaramoko project in Burkina Faso in 2010. Since this time, it has actively progressed the project with the completion of a preliminary economic assessment in 2013, a feasibility study in early 2014 and obtained full permitting for construction in January 2015. With no other underground gold mine in Burkina Faso, developing a modern and productive modern gold mine in West Africa was considered a significant challenge as Roxgold moved from explorer to producer.To facilitate this development, Roxgold engaged an international underground mining contractor to partner this development. This has enabled Roxgold to successfully develop the mine over a relatively short time frame with construction commencing in April 2015, first gold being poured in May 2016 and commercial production being achieved in October 2016.This paper discusses key elements of the project development and highlights some of the challenges faced with operating in a remote poorly developed area with a limited mining culture. Furthermore, the authors highlight the key technical and operational aspects that make the Yaramoko project a very successful development project.CITATION:Cope, B and Churi, Y, 2017. The development of the Yaramoko gold project in Burkina Faso, West Africa, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By S Wellink, D Chalmers, D Adermann, C Martin

The practice of recording blasts for quality control purposes has been conducted for several decades. However, at the low frame rates of a standard video camera, essential data is frequently missed as it occurs when the shutter is closed between frames.The use of high-speed video for the research, development and monitoring of the performance of blasting procedures is a well proven but under-utilised practice.The recent development of low cost, easy to use high-speed digital cameras and user friendly software can deliver a capability into mine management as a day-to-day production tool that can greatly improve blasting performance and reduce costs.Digital high-speed video and image analysis software can accurately quantify each blast. Analysis of the images can facilitate the identification of causes of variance from design, geology changes, errors in blast practice and areas of poor performance. The use of high-speed video greatly enhances the audit and review processes so that future blast design can be quickly and appropriately modified to deliver improved blasting performance and reduced costs.The three videos demonstrate the differences between standard video and high-speed video and the detail that can be obtained from them. These videos of open cut blasts can be used to identify blast performance variances. Capturing images at 1000 frames per second allows the analysis on a millisecond timescale where detonator timings, fragmentation, venting, fume generation and flyrock can be accurately identified.CITATION:Adermann, D, Chalmers, D, Martin, C and Wellink, S, 2015. High-speed video – an essential blasting tool, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M. M. Ali, C. Musingwini, R. A. Phillips

The long-term open-pit mine production scheduling problem (OPMPSP) is typically solved in two broad stages. The first stage entails optimisation of the ultimate pit limit, which delimits the economical final pit and maximises the undiscounted value of the deposit. The second stage entails optimisation of the long-term open-pit mine production scheduling, which maximises the discounted value of the deposit. The long-term OPMPSP is a type of an NP-hard problem, such as the travelling salesman problem (TSP), because it is intrinsically complex to solve since it incorporates both hard and soft constraints. Therefore, metaheuristic approaches have been used to find global optimum solutions to the long-term OPMPSP. This paper presents a metaheuristic approach utilising a dual interchange algorithm (DIA) to solve the long-term OPMPSP. The DIA is a parent algorithm which supervises two subservient algorithms, namely, simulated annealing (SA) and Tabu search (TS). The DIA selects the better solution generated in each run from the two algorithms, and simultaneously penalises the algorithm that produced an inferior solution, while rewarding the one that produced a better solution. The DIA was tested on the three-dimensional Arizona Copper Deposit (KD) dataset, which is publicly available for research purposes from the online MineLib repository. It was set to generate net present values (NPVs) in five-minute intervals and the solution improved until it plateaued at about 30 minutes of runtime. The NPVs compared favourably to those obtained on the same KD dataset but obtained over 24-hour runtimes, when solved using simulated annealing and Tabu search algorithms, and the NPV generated from the work of Muñoz (2012) using the modified TopoSort as found on the MineLib repository at the time of this study. Therefore, this paper demonstrates that DIAs can be developed and used to solve the three-dimensional long-term OPMPSP.

Sep 1, 2021

By G. Akdogan, J. H. Zietsman, C. Dorfling, D. Attah-Kyei

The development of newer and improved electrical products has led to an increase in the rate at which older products are discarded as waste. The main focus of electronic waste is the printed circuit board (PCB) because of the inherently high value of contained metals such as gold and copper. Several options for treatment of the non-metallic fraction including material recycling, where the residue may be used as inclusions in concrete or asphalt materials with minimal processing or chemical recycling, where chemicals and fuels are produced from the residue using pyrolysis exist. In this paper, the utilisation of the non-metallic leached PCB waste fraction as reductant in secondary copper smelting was investigated. Analysis of the leached residue revealed that PCB is highly amorphous and has a carbon content of 28.5%, an oxygen content of 23.1%, with the ash and volatile matter contents 40.1% and 44.8% respectively. Thermodynamic simulations of secondary smelting of copper were conducted in terms of metal recovery, and the energy required when PCB was used as a reductant. The results were also compared with that of coal and PCB-coal blends. The simulations revealed that as PCB in the blend used as reductants increases, the amount of energy required for the smelting operation decreases. Metal recovery slightly decreased as the mass percent of PCB in the blend increased due to lower carbon content present in PCB relative to coal. The results also highlighted the energy saving with PCB-coal blends which was around 160 kWh per ton of feed relative to coal. The decrease in the amount of energy required for the operation is attributed to the higher volatile content of the PCB, which is also a part of the reduction process. Keywords: PCB leach residue, alternative reducing agent, secondary copper smelting

Jan 1, 2020

By Alireza Javadi Nooshabadi, Kota Hanumantha Rao

Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by sulphide minerals during grinding was examined. It was found that pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite ((Zn, Fe) S), and galena (PbS) generated H2O2 in pulp liquid during wet grinding and also when the freshly ground solids are placed in water immediately after dry grinding. Pyrite produced more H2O2 than other minerals and the order of H2O2 production by the minerals was found to be pyrite > chalcopyrite > sphalerite > galena. The pH of the water influenced the extent of hydrogen peroxide formation with greater amounts of H2O2 produced at highly acidic pH. Furthermore, the effect of mixed sulphide minerals, i.e., pyrite-chalcopyrite, pyrite-galena, chalcopyrite-galena and sphalerite-pyrite, sphalerite-chalcopyrite and sphalerite-galena on the formation of H2O2 showed increasing H2O2 formation with increasing pyrite fraction. There is clear correlation of the amount of H2O2 production with the rest potential of the sulphide minerals; the greater the rest potential of a mineral the greater the formation of H2O2. This study highlights the necessity of revisiting the electrochemical and/or galvanic interactions between sulphide minerals, and interaction mechanisms between pyrite and other sulphide minerals in terms of their flotation behavior in the context of inevitable H2O2 existence in the pulp liquid.

Jan 1, 2014

By Jin-yan TIE, Ke-xin JIAO, Qian Li, Hai-bin ZUO, Jian-Liang Zhang, Meng SHEN

This paper designs three factors such as temperature, pH, conductivity and three levels of orthogonal test. Temperature is a significant factor. However PH and conductivity are not significant through poor analysis. Further research is conducted on the temperature. Temperature stability is 50 . Suitable water velocity is 2.3m/s, which is calculated based on the largest part of the heat flux intensity and the corresponding water temperature should be controlled with 1.5. Meanwhile, water velocity increased has little effect on the heat transfer capabilities.

Jan 1, 2015

By Richard E. Thill

The Bureau of Mines' Oil Shale Data Bank (OSDB) was created in 1976 to serve as a centralized source for the storage, retrieval, and dissemination of technical literature, patents, and information on research projects in oil shale. Thousands of bibliographic references, patents, and research projects relating to the mining of oil shale have been identified, abstracted, and indexed according to selected keyword topics. The resulting data bank listings are contained in three sections, each with a separate keyword breakdown for use in rapidly identifying references pertaining to a specific subject. All references cited in the OSDB were published prior to an established cut-off date of May 1, 1981, when a redirection of Bureau of Mines programs resulted in the loss of project funds and the subsequent phasing-out of data bank operations. ACKNOWLEDGMENTS The oil shale data bank listings are the result of a team effort of the project staff. The contributions of Jimaleen Jansma for keypunching, information acquisition, and data entry, and John Brandenburg and Sandra Brake for keywording and information acquisition are gratefully acknowledged. Appreciation is expressed to the staff members of the Smithsonian Science Information Exchange, Washington D.C. for their cooperation in supplying data on recent research projects in oil shale for inclusion in the OSDB listings. Appreciation is extended also to the staff of the Gallegos Research Group for assisting with computer services to obtain the final printouts and transfer of files onto magnetic tape.

Jan 1, 1982

By G. S. Hume

Introduction Core drilling of the bituminous sands of northern Alberta has been carried on by the Mines and Geology Branch, Department of Mines and Resources, under the supervision of the Director, W. B. Timm. This was part of the Dominion Government's wartime investigations, which included an agreement with Abasand Oils, Limited, for the study of commercial possibilities of obtaining oil from the bituminous sands. The drilling programme, commenced in 1942 by the Consolidated Mining and Smelting Company of Canada, was continued in 1943 and subsequently by Boyles Bros. under contract with the Mines and Geology Branch. Several areas have been investigated and one of these, the Mildred-Ruth Lakes area, ' herein described, is of special importance in that it contains a sufficiently rich and large deposit of bituminous sands and bitumen beds to warrant consideration of commercial developments for the production of oil. The Steepbank Area, East Side of Athabaska River The Steepbank area, on the east side of Athabaska river in township 92, about twenty-two miles north of Fort McMurray, was selected for drilling in 1942 because previous investigations by Ells indicated it was one of considerable promise both from the standpoint of having reasonably rich bituminous sands under relatively light overburden and also having an excellent tailing disposal and plant site for large-scale operations in proximity to Athabaska river. The drilling done in 1942 and 1943 was largely exploratory, and, when it was found that the southerly part of township 92 had only low-grade material, closer drilling was done in 1944-45 in the richer, more northerly part.

Jan 1, 1947