Search Documents

By Richard Kunter

INTRODUCTION Additional work has been done on the CIP circuit at Creede, and a brief description of this work is presented in this paper. DREDGE The original dredge for the Bulldog was built by Al Hack, Inc. of Denver. The dredge cutter head is mounted on a boom made of 6-inch diameter pipe which is raised and lowered by a cable-pulley system. Maximum cutting depth is 8 feet. Slurry from the dredge flows through a floating 6-inch diameter pipe supported on 55-gallon drums which runs from the dredge to the shore and then to a trash screen and pumping system. See Figures 1 and 2. The cutter head, suction pump, winches for dredge movement, and all other operations are controlled from a small operations house located toward the rear of the dredge. All of the basic dredge equipment is mounted on a chassis about 8 ft x 16 ft in size. Additional buoyancy was originally provided by sealed 55-gallon drums supported along the sides of the chassis by a small wooden framework. Additional framework and barrels on the front of the chassis on either side of the cutter boom provided additional stability, particularly when digging in hard material. The dredge was quite stable, but two problems were apparent. For one, it could have been sunk by someone from the shore firing a rifle into all of the barrels. In prime deer-hunting and sportsman country

Jan 1, 1983

By Al Romphf

Managing blasting-induced air overpressure levels is a key compliance requirement for most blasting operations. Regression analysis, plotting overpressure amplitude vs cube root scaled distance, will often present a level of scatter which should be considered unacceptable. Relying solely on regression-based predictions can lead to overly conservative restrictions that may negatively impact other key performance indicators. Improved methods are needed for accurate overpressure prediction. The Heelan-Blair wavelet has been shown to closely resemble the overpressure waveshape produced when a single charge is fired under typical confinement conditions. The amplitude of a single-hole overpressure wave is influenced by factors such as proximity to the receiver, charge mass, orientation, and confinement both at the collar and face. Additional factors, including timing sequence, barrier effects, wind direction and velocity, must also be considered. The linear superposition method, commonly applied for ground vibration prediction, can be adapted for air overpressure modelling. In blast design software, this approach can consider all relevant parameters and environmental interactions. Given the uniform nature of air compared to rock, linear superposition using realistic elemental wavelets may replace the need to fire a signature hole. Data from 38 single-hole blasts conducted at quarries and mines throughout North America were used to develop and calibrate a linear superposition model. This model reasonably reproduces air overpressure results from full-scale production blasts, offering a practical approach to overpressure compliance and prediction.

Jan 26, 2026

By Harry Wilton-Clark

Introduction Coal cleaning may be taken as meaning the separation of coal-as-mined into two or more fractions. Coal cleaning includes coal washing, together with any other means used in the ultimate preparation of coal prior to shipment (as coal) . The method of coal cleaning devised for any given mine must be one which is based entirely on the economic results obtainable. The installation of a high-cost and complex washing plant, designed to produce a low-ash dean coal, at the highest possible recovery, may be unsound practice. A crude 'roughing' washer may be the best result of sound engineering and operating consideration, and in some cases coal cleaning should be confined entirely to preparation at the face. Consideration of complete costs, to the point where the coal is actually sold, may show that certain seams are workable or not workable. Of the seams found workable, extraction of the whole or parts of the seam may be decided on. The portion to be extracted may contain rock or bone partings, which must be removed. It may be good practice to mine the extra portion and remove the objectionable materials by surface washing; or it may be that such materials should be removed underground, even at an increased mining cost. For instance, in some of the steeply pitching seams of the Alberta Crow's Nest Pass district, the removal of bone and rock at the face may be almost impossible under the usual 'up the pitch' or 'angle' mining methods, but possible by mining across the pitch so that the material to be rejected can be removed and gobbed. Again, if a complete seam is being extracted, investigation may show marked differences between top coal and bench coal, and if sufficient mine cars are being loaded from a chute at one time, the fact that such a place is working top or bench coal at the time may be reflected by peaks in ash content or size proportions at the ripple. It may be very effective coal preparation to smooth out such peaks.

Jan 1, 1934

By B. W. Naugle

A small-scale laboratory coke oven similar to those described by Swiniarski, Cryan, and Altieri and Fuchs, Sandhoff, Taylor, and Gauger was built by the Bureau of Mines in 1943. Tests made since that time have indicated that such a small oven is of questionable value in predicting the coking pressures to be expected in commercial coke ovens. This summary of the work done has been prepared at the suggestion of the Advisory Committee to the Bureau of Mines-American Gas Association Survey of Carbonizing Prop¬erties of American Coals.

Jan 1, 1948

By S. H. Ash

THE INUNDATION of anthracite reserves in the Eastern Middle field of Pennsylvania affects the life of the anthracite industry in this field; it also influences the economic status of people, communities, and industries that depend wholly or in part upon anthracite for their livelihood. The trends of production and of employment in the anthracite-mining industry in this field are downward, and they probably will continue in this direction. The reserves have been depleted to the extent that the end of the active life of the industry as a. major economic factor is approaching. By removing the water in those pools where it can be done economically, the future of this industry may be extended somewhat.

Jan 1, 1950

By Eugene T. Sheridan

The United States has extensive reserves of peat. Peat and muck lands are estimated at approximately 79 million acres, with reserves of 13.8 billion net tons. Within the past decade domestic production of peat has increased 2-1/2 times, and apparent consumption has tripled. During the same period imports have increased greatly, and in 1955 they almost equaled domestic production. The substantial increase in the demand for peat in the United States was due chiefly to expanding markets in agriculture and horticulture, for the reason that in this country peat is used primarily as a source of organic matter to improve the physical condition of mineral soils and as a mulch for shrubbery. A valuable constituent of any soil is its organic matter, and its depletion will injure cultivated soils and subject them to greater erosion.

Jan 1, 1957

By Susan G. Bilhorn

A number of studies have been conducted in active and inactive mine environments using continuous monitoring and data acquisition systems to detect various parameters. In addition to the information obtained for research purposes, these monitoring systems can provide a means to remotely collect required information (such as radon daughter concentrations and air velocity) and control various conditions (such as fan operation and air door position) in numerous working sections of an active mine. Selection of detector locations and placement, which are critical to obtain the information and control desired while not inhibiting mine operations and influencing the detector readings, are covered in this paper.

Jan 1, 1984

By W. J. Long

As a part of the strategic mineral exploration program, examining engineers of the Bureau of Mines collected samples of ore from four manganese properties in Yavapai, Yuma, Maricopa, and Mohave Counties, Ariz. As all of the ores were too low in grade to be acceptable by manufacturers of ferromanganese beneficiation studies were made to determine the amenability of the ores to concentration.

Jan 1, 1948

Following the Moura No 2 Wardens Court of Inquiry and subsequent changes to the Queensland Mining Legislation there is a requirement in Queensland coal mines for: a person with the recognised competencies to be appointed at each underground coal mine to the position Ventilation Officer; and the person is directly responsible for the implementation of the mine ventilation system and for the establishment of effective standards of ventilation for the mine. The Regulations require that an underground mine must have principal hazard management plans that provide for at the least the following: emergency response, gas management, methane drainage, mine ventilation, spontaneous combustion, and strata control. Other than strata control all the plans require the ventilation officer to have roles and responsibilities to develop, control, monitor and undertake actions in relation to these plans.There are also another 34 Regulations that either directly or indirectly requires the Ventilation Officer to take actions.The purpose of this paper is to outline the information that the regulators look for in sealing plans and the actions the regulators will take if the sealing does not go to plan (TARPs being exceeded).

Jan 1, 2005

By B Manda, K L. Sandvik, K Musiwa

Mining and processing of pyrite ore at Iron Duke Mine, north east of Zimbabwe, generates large quantities of acidic mine water as a result of the oxidation of iron sulfides on exposure to air and water used in the drilling and blasting operations. The acid mine drainage (AMD) contains elevated levels of dissolved Fe, Al, Mn and sulfate and has characteristic pH values ranging from about 0.50 to 3.00. Handling and disposal of such a drainage places significant impacts on the economics of the mining operation due to the corrosive nature of the drainage on infrastructure, the limitations placed on water reuse and discharge to the environment under a new law governing effluent discharge. Treated sludge at Iron Duke is chemically unstable, changing pH from ~7 to ~3 within four days after deposition in the evaporation ponds. The effluent does not meet the permitted level of neutral pH, 500 mg/l sulfate and less than 2000 mg/l total dissolved solids. Excessive acid seepage from the evaporation ponds has resulted in contamination of the ground water below the ponds area, which shows high mean annual levels of iron (368.67 mg/l), sulfate (1702.89 mg/l) and low pH (2.86) in addition to other pollutants. This poor quality seepage infiltrates into the nearby Yellow Jacket River, contaminating the public water source. Furthermore, a deterioration of the land area and vegetation adjacent to the tailings dump is also observed. Understanding the controls on the neutralisation of acidic drainage and long-term sludge stability after placement in evaporation ponds is essential to minimise costs of closure requirements and for the protection of environment and human health. This study examined the effects of the master variables pH, redox potential, acidity and alkalinity on acid neutralisation. The results indicate that ferrous hydroxides are not as stable as ferric hydroxides and that proper oxidation of iron also leads to better sludge stability, higher treatment efficiency and a manageable sludge viscosity. Metal hydrolysis and secondary mineral formation at the evaporation ponds under a wide range of pH and redox conditions is responsible for equilibrium shifts in metal reactions, resulting in high potential for metal leaching and mobility. Mechanisms of metal attenuation are also discussed.

Jan 1, 2006

By E. L. Evans

The historical development of South Yorkshire mining is traced and note made of the liability to generate spontaneous combustion of some of the seams which have been worked. The liability factor is analysed firstly as an inherent property in the material of a coal seam, and secondly as a circumstance of a situation in which access is provided for the air necessary to sustain oxidation. The geological settings in which incidents of heatings have been known to occur is discussed and conditions favouring a natural pre-disposition to spontaneous oxidation exposed, particularly the effect of argillaceous material overlying the seam. An extensive strata-dynamic study follows to demonstrate the situations in which stray air currents tend to impinge on readily oxidizable material. Prevention techniques are indicated as the identification of strata-dynamic situations in which air access to broken coal is induced and thereafter th operational action to seal off the voids which have been opened up so as to exclude air from the broken coal. Measures to reduce the tendency for ventilating air to short circuit across waste voids, and to obviate deflection of air into packs are outlined. The importance of face and roadway design features is demonstrated and the consequences of practices inimical to good control of spontaneous combustion are related. Discussions on means of detection and also on the sealant materials available are included.

May 23, 1905

By D. J. Parker

In attempting to discuss a subject of this character it should be clearly understood at the outset that the purpose is not to emphasize the mere fact of occurrence of such catastrophes, the memory of which time has largely relegated to oblivion, but rather to stress the means of their prevention, available not only subsequent to but also at the time of occurrence. A careful, conscientious, unbiased study of the causes of mine explosions leads inevitably and definitely to the conclusion that the human element is the most important factor. The human factor should however, be evaluated in terms of responsibility--responsibility on the part of the employer to recognize the existing hazards and take the necessary remedial action, and on the part of the employee to perform his duties faithfully, diligently, scrupulously, and in strict conformity with State mining laws and company rules or other regulations.

Jan 1, 1933

By B. Arsenault

Aluminum coatings can provide galvanic cathodic protection for several metals and alloys, In order to be a suitable protective solution on structural components, the mechanical integrity of the component must be preserved, In particular, fatigue properties are a challenge for thermal-spray protective coatings on mechanical structures, To address the issue of the fatigue integrity of 7075 aluminum alloy with an arc-sprayed protective coating, different surface preparations prior to arc spraying were considered, In the present work, a feasibility study was performed using laser ablation as a surface-preparation technique before or during arc spraying of coatings, This was collaborative effort between the LERMPS laboratory in France, the National Research Council Canada and the Royal Military College of Canada, Both fatigue and adhesive properties of aluminum coatings were evaluated in relation to substrate-surface-preparation techniques including laser ablation (Protal® process), grit blasting and shot peening. Results indicate that a combination of key conditions, including the use of nitrogen as the arc spray gas, shot peening, and proper laser energy density for ablation, provide high fatigue resistance of metallic coated 7075 alloy substrates. Specimens prepared under these conditions show a similar fatigue resistance to uncoated substrates.

Jan 1, 2005

By A. Brown

THIS P APER has been pre-pared as a progress report on Mines Branch investigations into problems of ground stress in certain co al mines of Western Canada. As such, it should be considered as a companion report to the one ( 1) presented to the Mining Society of Nova Scotia in 1956 and which dealt with similar investigations in the coal mines of Eastern Canada. For the past 50 years, dynamic incidents in the form of 'bumps' and 'outbursts' have been occurring in the coal mines of the Inner Foot-hills belt of tl1e Canadian Cordillera. As these phenomena generally become more frequent with in-creased thickness of overburden, a limiting depth of mining of 2,500 feet has been set (2) for estimating recoverable reserves of coal. If such a view were accepted, from a long-term viewpoint very large resources of coking-grade ?coal -in a part of the continent deficient in such coals -would not be available to the nation. The terrain in which these in-6dents take place may be described in geological terms as being dominated by pronounced structure in strata ?consisting of a large proportion of highly indurated rocks. The Geological Survey of Canada has co-operated by carrying out structural studies (3) at the mines, supplemented lithological by stratigraphic observations.

Jan 1, 1958

By K. N. Bolatbaev, S. S. Naboichenko

The initial rates of dissolution of pyrite, chalcosine, sphalerite and galena in acidic sulphate solutions under oxygen pressure were measured in the range of Poe = 0.2-1 MPa, 130-180 °C, [H2SO4]0 = 0.2-0.7 M, and in the presence of surface-active agents and agitation producing Re = 4-16 x 103. Reaction orders, activation energies, and values of reaction constants for these oxidation reactions were established. The reactions also were shown to be diffusion-controlled; and the rates demonstrate a linear dependence on the surface area of the sulphides. A surface reaction model, in which oxygen is transported through a solid layer of surface products, has been advanced. The initial stage of high-temperature interaction at pH <7 is suggested to involve a chemical activation of the sulphide surface and is described by the following general reaction: MenSm + H3O+ Men-1 Sm-1 (HS-)s + H2O The subsequent oxidation of surface complex HS- to S0 or SO2-4 occurs with the assistance of Fe(III), Cu(II) ions depending on temperature and the redox potential of the medium, which are defined by oxygen pressure and composition of the reaction mixture, especially concentrations of H2SO4 and metals with variable valence. General process kinetics are complicated due to the formation of by-products on the basis of Fe3+ Pb2+, Cup ions, which displace the kinetics into the diffusion region.

Jan 1, 2004

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of underground mining conditions on the activation of automatic sprinkler heads. Sprinklers were exposed to liquid fuel fires in a rectangular tunnel at airflows of 0, 45, 90, 150, and 250 m/min to determine the effect of ventilation and fire size on the time to activation. As the airflows were increased, the time to activate the sprinklers for a given fire size increased. Also, as the fire size increased, the activation time decreased. Temperature profiles of the tunnel showed that the maximum temperature near the roof was shifted downstream as the airflow increased. Experiments to determine the effect of rated activation temperature and response time index (RTI) value on activation time showed that the time to activate increased with increasing activation temperature, and decreased with decreasing RTI value. Exposure to the mine environment showed little effect on the activation times in large-scale experiments, and no significant effect in laboratory experiments. The results showed that airflow can have a significant effect on the activation times of automatic sprinklers. This needs to be considered in the design of effective sprinkler suppression systems for ventilated areas.

Jan 1, 2010

By J. A. Brothers, M. R. Foran

"AbstractThis paper reviews the progress made in the manufacture of hydraulic cement from iron blast-furnace slag by simply grinding the granulated material with other constituents. The influence of the chemical and mineralogical composition of the slag, the conditions of granulation, the manner of drying, and the fineness of grinding, on the hydraulic properties of the cement, is discussed. The effect of additions of lime, portland cement, and anhydrite, alone and in combination, on the physical and cementing qualities of the mortar and concrete made from Sydney blast furnace slag, is shown in tables of data and is reviewed in some de- tail. The work at the Nova Scotia Technical College has shown that a cement equivalent in every respect to portland cement can be made from basic blast furnace slag- by the us2 of certain quantities of portland cement as an activator.IntroductionBlast furnace slag is a potentially valuable material for the manufacture of hydraulic cement. It is a by-product of the manufacture of iron in the blast furnace, and is formed by the combination of the silica and alumina .of the iron ore with the limestone flux. The metallurgist terms a slag .acid or •basic according as the percentage of lime is less or greater than the percentage of silica plus alumina. The basic slags have the •more pronounced hydraulic properties."

Jan 1, 1950

By Frank E. Scott

During the past year interest in the use of hydrazine and hydrazine hydrate as a fuel has increased in the United States; For this reason it was felt to be desirable to obtain information on the explosives properties (if these materials in order that hazards inherent in their manufacture, storage, transportation, and use might be evaluated.

Jan 1, 1949

By M. Vallée

Several reviews of mineral project performance in the past 35 years indicate a pattern of occasional, but recurrent, mining project failures due to shortcomings in geological information and estimation, mineral processing and metallurgical testing, feasibility study objectives and requirements, and project start-up methods. A commitment to quality assurance and continuous improvement methods and to obtaining “ENOUGH DATA, OF APPROPRIATE QUALITY” is essential. Recent international and Canadian proposals for mineral resource and ore reserve definitions have taken a nonprescriptive stance that will undermine the formulation of requirements, guidelines and industry standards for efficient deposit delineation and estimation, and for the determination of project feasibility. To help reduce problems, every feasibility study supporting a mine development and production decision should be based on objectives and methods adequate to reach completion targets similar to the bankers’, as a good business target for a profitable project. In a resource/reserve system, the use of reserve should be restricted to a project that meets required technical, economic and legal feasibility requirements for successful project implementation, and the definitions of these categories should provide explicit limits. Current shortcomings will limit the ability of the Qualified Person to provide “adequate professional practice,” fulfill his/her professional responsibilities to his employer or client and provide adequate information to the investing public. We must take advantage of present opportunities for Setting New Standards for the new Millennium.

Jan 1, 2000

By Howard C. Pettibone

Mine safety personnel reported occurrences of excessive "glove-fingering" and other problems with resin-grouted roof bolt installa tions. To study these problems, the Bureau of Mines designed a test plan to (1) obtain baseline information on several resin cartridges and (2) investigate the variables involved in the installation of a resin bolt. Three brands of resin representative of the industry in January 1983 were selected for cartridge evaluation. The installation variables selected for study were the method of installation, the hole depth, and the hole annulus. These variables were studied by installing a series of bolts in concrete blocks using different values for each variable. Results of the research show overspinning the resin may cause problems, but they can be avoided by using the spin times recommended by manufac-turers. Excessive glove-fingering is not a problem if the manufacturer-recommended installation procedures are followed.

Jan 1, 1987