Search Documents

By E J. Coyle, L A. Millington

Tailings storage facilities are geotechnically complicated structures that develop heterogeneous strength profiles and varied porewater conditions. The monitoring of porewater pressures is one of the only direct measurements that can be performed to monitor the performance of a facility throughout its life and is of particular importance in upstream facilities. Foundation underdrainage, continuous and staged tailings deposition, climate inputs (rain, snow, humidity, evaporation, etc), and stratified tailings permeabilities can complicate this critical measurement that introduces uncertainty to stability analyses. These difficult conditions manifest in vibrating wire piezometer measurements as very low or negative pressure readings, both of which are within the instrument’s range of accuracy. However, the data can be difficult to interpret, and a range of interpretations are adopted from optimistic low phreatic surfaces to conservative fully saturated tailings. Where tailings are potentially liquefiable, these very low readings introduce further uncertainty regarding the pore space saturation ratio and liquefaction potential above the estimated phreatic surface. This area of uncertainty is the vadose zone, and its affect on tailings behaviour is not well understood. The two facilities analysed in this paper are upstream, raised embankments with tailings classified as clayey, sandy silt that have been found to be potentially liquefiable. The vibrating wire piezometers (VWP) at both sites show very low or negative readings when they are initially installed near the surface and then go through cycles of re-saturation and de-saturation. Eventually the readings settle as the VWPs are buried deeper within the tailings. The instrumented sections within the tailings column do not show consistent readings that would be indicative of a hydrostatic phreatic surface at either site. Rather, they are highly variable and can be interpreted as either representing a high phreatic surface within the tailings or as a ‘perched’ phreatic zone within the tailings layers. How the VWP data is interpreted has a significant impact on how the facilities are raised and operated. The design outcome for Site 1, which adopts a lower phreatic surface, results in an embankment that meets factor of safety (FoS) requirements under residual strength conditions without any buttressing. Conversely, a conservative (high) phreatic surface has been adopted for Site 2 and has resulted in the facility requiring a significant buttress to meet FoS under residual strength conditions.

Jul 1, 2021

By R. E. Chaney

This report summarizes the research on the Strategic and Critical Materials Program tasks conducted at the Idaho National Engineering Laboratory (INEL) between Mdy 1983 and April 1984. The work is divided into two areas: 1. Production Technologies - Tasks directed at developing advanced extraction technologies ? Biologically-Assisted Minerals Processing ? Metal/Gas Reactions and Thermal Plasmas ? Dehydration of Aluminum Chloride Hexahydrate. 2. Conservation/Substitution Technologies - Tasks directed toward establishing the technical processing base which will permit the use of advanced materials ? Joining of Rapidly Solidified Alloys (RSA) ? Joining of Silicon Nitride-Based Ceramics ? Nondestructive Evaluation of Ceramic and RSA Joints and Materials.

Jan 1, 1984

By L. M. Chan, D. H. Carlson, J. B. Johnson

"Abstract — Concentrations of tailpipe pollutants from diesel-powered. underground mine vehicles change over time due to engine wear and the need for maintenance. Since this deterioration in pollutant emissions may adversely affect the air quality in an underground mine, it should be monitored and controlled. This paper presents decision criteria concerning when to service a mine vehicle diesel engine. These criteria, based on mine air and tailpipe concentration measurements, are designed to maintain the tailpipe concentrations within limits that assure satisfactory mine air quality.Application of the deterioration criteria to mine vehicle emissions involves:establishing, for each pollutant, the allowable deterioration factor, anddetermining the deterioration factor, from the mine air and tailpipe diesel pollutant measurements, and the mine air threshold limit values (TLVs).If the deterioration factor is greater than or equal to the allowable deterioration factor the vehicle is removed from service for maintenance.An analysis applying the criteria to measurements made in an underground coal mine is presented. The tailpipe pollutant concentration data were collected using the Emissions Mea-surement Apparatus (EMA) developed by Michigan Techno-logical University. Since the TLV for diesel particulate matter (DPM) has not yet been established assumed mine air DPMTLVs of 15 and 1.0 mg/m3 were used in the analysis. For all of the diesel haulage vehicles included in the analysis. DPM was found to be the critical pollutant (the one most in need of control). For an assumed mine air DPM TLV of 15 mg/m3 none of the diesel haulage vehicles would he removed from service. However reducing the DPM TLV to 1.0 mg/m3 would make it necessary to remove two of the three vehicles tested from service."

Mar 1, 1992

By Bethany Witter

In the past decades, a technological explosion has caused generational shifts. First, millennials experienced a technological shift to computers and cellphones. Next, Generation Z experienced a shift to smart phones and social media. These two generations are immersed in technology and are accustomed to constant connectivity. How do the extractive and construction industries gain the interest of younger generations and integrate them into the industry? The Virginia Tech Student Chapter of the International Society of Explosives Engineers handled this same issue with its recruitment efforts and event planning from 2017-2019. The first critical component of integrating Generation Z college students into the extractive industries is clear and frequent communication via email. Next, Generation Z often values the motivation behind work when choosing a career, so advertising technological advancements, benefits, and ways people can contribute to improving the industry also helps attract young generations. Similarly, advertising opportunities for people to work outside with their hands, travel, and secure stable careers can attract students. At Virginia Tech, the most effective way to attract and maintain the interest of students in extractive industries is to put the students in the field. Field trips to mines and factories experienced the most stable attendance and highest survey reviews of all other chapter events. Guest presentations from industry professionals were often well attended, but attendance tapered off as the academic year progressed and students grew busier. Periodic trips throughout the year maintained student engagement and often supplemented their curriculum. The student chapter was relatively successful in attracting students, but it struggled to maintain attendance levels in the latter portion of the academic year. In the future, the industry can increase its recruitment of Generation Z and Millennials into the workforce by working more closely with university programs to provide resources and opportunities for hands-on experiences for students.

By C Rothfuss, X Wang, S J. Herbert, K Prasad

The extraction of groundwater to produce gas from coal seam gas (CSG) reservoirs has highlighted the opportunity for beneficial uses of groundwater in Australia. This paper presents an assessment of alternate groundwater modelling approaches that can be used for assessment of one beneficial use option, that of injection. This assessment examines the outcome of the use of different simulation methods on predictions of hydrodynamic behaviour.In this paper, a simplified hydraulic concept of a multi-aquifer system within the hypothetical injection field was used to investigate the hydrodynamic behaviour of injection into the Precipice Sandstone. Comparisons were made through the analysis of a Theis 3D analytical solution with 2D and 3D numerical solutions. The paper discusses the different solution methods and the impact of these on predictions of pressure and flux. Differences in 2D and 3D solutions result in implications if planning injection as a beneficial use of water. For example, the 2D solution resulted in faster and higher injection pressure build-up when compared to the 3D solutions. The 2D modelling could result in either plans that require higher capital expenditure for a greater number of wells in order to spread the pressure effect and remain below the maximum injection pressure or a reduced injection rate. Meanwhile, the 3D modelling with sensitivity analysis could result in planning for lower capital expenditure for fewer wells required to spread the pressure effect and remain below the maximum injection pressure. CITATION:Wang, X, Herbert, S J,?Rothfuss, C and Prasad, K, 2013. Assessment of effectiveness of artificial recharge for coal seam gas water management based on numerical modelling, in Proceedings Water in Mining 2013 , pp 67-72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Maria K. Kojo

The interaction between various slags and a nickel concentrate containing pyrite, pentlandite, and violarite were investigated by submerging concentrate pellets in molten slags. The slags were contained in MgO-A12O3 spinel crucibles. The slag oxidizes the iron sulfides in the concentrate, resulting in a nickel matte. The amount of S02 gas formed during reaction was measured to determine the oxidation reactivity of the slags. The experimental variables included temperature, the ferric/ferrous ratio of slag, and other slag properties such as the FeO/SiO2 ratio and the MgO and NiO contents. The reactivity of the slag depended in a complex manner on its oxidizing power, viscosity, and interfacial tension. The slag composition for the greatest reactivity was determined to be Fe3+/Fe2+ = 0.3, Fe/SiO2 = 1.3, and % MgO = 2. This slag, however, caused substantial foaming. Increasing the MgO content to 10% or replacing it by 5% MgO + 8% NiO eliminated at a slight decrease in reactivity. The implications of the findings from this work in the bath smelting of nickel sulfide concentrates are discussed.

Jan 1, 1995

By Daniel Torres Espinoza, Jose Pinedo

"Ventilation is a vital service in underground mines, required to provide fresh air to the work force and dilute diesel equipment gases (CO, NOx) and diesel particulate matters (DPM). At a Mexican precious metal mine in the state of Chihuahua there is a VOD system implemented using Howden’s control and monitoring system and a state of the art tagging and tracking technology. The JM zone of the mine is ventilated using a push and pull system, using automated regulators on each level to control the air going in and out of the levels. The implementation of advanced control strategies using Howden’s VentSim™CONTROL allows the mine to generate significant savings and increase health and safety of the workers.INTRODUCTIONIn underground mines, ventilation is a requirement in order to maintain the fresh air needed for personnel and equipment. Ventilation regulations dictate the amount of air required underground to carry out day to day operations by limiting the exposure that workers have to toxic gases and other pollutants. Regulations for required airflow in underground operations for diesel pollutants are generally provided on vehicle rated brake horsepower, in Mexico the requirement is 75 cfm/bhp. In underground mines, ventilation services can account to up to 75% of the mine’s energy consumption, and it is very common for fans to operate all the time because of a lack of control infrastructure for the ventilation system. By the implementation of a Ventilation On Demand (VOD) system a mine can reduce this consumption with different control strategies. The main infrastructure required to implement this system consists of remote control of ventilation infrastructure (fans and regulators), a communication network between throughout the mine with the surface and a tracking system for personnel and diesel equipment. Software is required to determine fresh air requirements based on the tracking system data and then send the control commands to the different ventilation infrastructure. In 2015, San Julian Mine acquired Howden’s VentSim™CONTROL (formally SmartEXEC) and the hardware solution to deploy a VOD system at their operation. The VOD system and Fresnillo plc’s San Julian Mine in Chihuahua, Mexico, consists of control of 10 surface exhaust fans, 2 surface intake fans, and 12 underground automated regulators. It also includes the monitoring of 46 flow sensors, 28 CO sensors, 28 NO?? sensors and 42 temperature and humidity sensors, approximately 500 personnel tags, approximately 220 vehicle tracking tags with diesel status (ON or OFF) and approximately 250 tracking zones. This paper discusses the control strategies that have been implemented at San Julian Mine since the system was commissioned and the next steps that will be taken at the mine with the system as they test different level on VOD."

Jan 1, 2019

By J. Jávor

The response of the air/water interfaces to deformation in presence of surfactants is affected by the adsorption/desorption rate, re-orientation and exchange rate of surfactant. These surface properties can be observed using equilibrium and dynamic surface tension and surface elasticity measurements. However, the effect of these parameters on bubble size in dynamic conditions has not been studied due to the difficulty in capturing freshly formed bubbles in dynamic conditions. The paper presents a new experimental set-up designed and built at the Aalto University, called Shear Force Observation Chamber(SOC). The setupallows the monitoring and analysisof freshly formed air/liquid interfaces in dynamic conditions and facilitates the study of the effect of dynamic surface tension and surface elasticityon freshly formed air bubblesin presence of surfactants. The method helps to establish correlation between bubble size and dynamic interfacial properties and bubble-bubble interaction in turbulent flow. Dowfroth 200, Nasfroth 240 and Dowfroth 250 commercial flotation frothers were tested in this study. The results show a marked difference between results obtained in dynamic conditions compared to the static conditions. The results are presented and the reasons and implication to flotation modelling are discussed in the paper. Keywords: shear force observation chamber, flotation frothers, flotation bubbles, critical coalescence concentration

Sep 1, 2012

By Xubo Chen, Zhiqiang Hu, Zhijian Sun, Gaoyun Zhou

"The research aimed at developing an efficient and environmental frother,which was applied in the flotation of sulfide ores. The flotation properties of an efficient frother and pine oil have been studied relatively by flotation tests of lead and zinc sulfide ores. At the same time, the biodegradability of two kinds of frother has been studied by the method of biological respiratory curve. The test results show that the flotation properties of new frother are superior to pine oil such as flotation rate, dosage etc. and its biodegradability is superior to pine oil. INTRODUCTION Frother is a kind of important agent in flotation reagents.In practice, the criterion of the foaming performance of the frother is what is high and low according to flotation indexes. The difference of different minerals and flotation technologies has great influence on the foaming performance of frother, and it is very important to choose the corresponding frother. The type, dosage and selectivity of frother in flotation process must be considered carefully. In today's society, environmental protection and ecological protection are becoming more and more important, and the environmental and ecological damage from mine development has aroused increasingly more attention. The use of mine agents has promoted the development of mineral resources, greatly improves the recovering utilization of mineral resources, at the same time, the production and use of mine reagents also inevitably bring about pollution, and result some influence or damage in the ecological environment.The frother is a common kind of reagent in the flotation process of the concentrator. In many cases, the waste water in the concentrator can not be let out in the natural water because the higher content of the frother in the waste water results in higher index of COD.This will inevitably increase the cost of waste water treatment in the mine.Therefore, the choice of frother should not only consider its influence on the flotation index, but also consider its influence on environmental protection. Waste water treatment is a way to solve the waste water pollution, but it needs to cost a lot of fund, manpower and material resources.And the development of high efficiency pollution-free reagent is a good way to reduce the production cost of mining enterprises and reduce the environmental pollution."

Jan 1, 2018

By A. T. Iannacchione

Unfortunately from 1991 through 1995, 44 miners were fatally injured in the stone industry. Of these 12 occurred at underground mines from a total work force of less than 2,000 miners. Nine of these 12 miners were fatally injured in falls of roof or rib. A safer environment for the miners can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground control strategies. Roof and rib conditions in the underground stone industry were observed and assessed at 33 mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania, and West Virginia (Figure 1). Hazard assessment indicated that those ground failures occurring under moderate to substantial overburden ( > 30 m [100 ft]) were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine layout decisions tremendously influence ground stability.

Jan 1, 1997

By Lei Zhang, Xianjun Lu1, Minjie Lian, Liyang Zheng

In order to investigate rheological behaviour of fine tailings backfill pastes, the fine iron ore tailings (size fraction of -0.074mm accounts for 70%) from Fuquan Mining Co., Ltd. of Sinosteel Corporation (Shandong, China) was investigated. The rheological parameters such as slump, viscosity and yield stress of the tailings pastes under different densities were measured in detail, and the effect of paste density on the rheological property and the relationships of different rheological parameters of the pastes were also discussed. According to the results, the rheological behaviour is in accordance with the pseudoplastic fluid in a wide range of paste densities (solid content, w/w) of 65% to 80% and the pastes turn to be Bingham fluids at higher shearing rates. Along with the increase of paste density, the slump drops gradually and the viscosity and shear stress increase gradually. However, the variation extent of the rheological parameters varies at different density ranges. According to the variation pattern of the rheological parameters at different paste densities, the flow ability of the pastes can be classified into three zones. The high fluidity zone was observed at the density range of 65%-69% where the rheological parameters vary slightly along with the paste density, the moderate fluidity zone was observed at the density range of 70%-76% where the rheological parameters vary significantly along with the paste density, and the low fluidity zone was observed at the density range of more than 76% where the rheological parameters vary sharply along with the paste density and the critical density for this sudden variation is about 76%. Furthermore, linear correlations of slump/viscosity and slump/yield stress were observed. It is possible to predict the viscosity and yield stress of the pastes based on the slump measurements.

Jan 1, 2014

By M. F. Vancas

The advantages of using vertical pulsed columns as replacements for conventional mixer/settlers in the uranium industry have been known for some time. The advantages of the columns offer include a reduction in real estate for the plant, elimination of diluent evaporation and crud formation. This paper presents the findings of laboratory tests of pulsed columns extracting copper from pregnant leach solutions and also discusses potential advantages of the pulse column in copper solvent extraction.

Jan 1, 1999

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By Yadong Xue, Fei Wang, Hongwei Huang, Yan Sun

"Increasing attention to subway tunnel maintenance is being paid with the high speed development of urban rail transit system in China. A novel moving tunnel inspection equipment based on machine vision is developed in this paper. High resolution image acquisition system is proposed for tunnel crack and leakage inspection. The main components of this image acquisition system includes high speed CCD cameras, linear lights and high performance computer. To inspect the crack less than 0.3mm with a 3-5km/h speed in subway tunnel, we need to consider resolution and line rate of camera, pixels of cameras, range of inspection and illumination intensity of lights simultaneously. The optimization design is proposed to make the equipment more convenient for tunnel use. Entire tunnel situation can be detected and recorded in a single inspection process. This equipment has already been verified in Shanghai subway tunnel for defects inspection.1. INTRODUCTION In China, the quantity of subway tunnel has reached a large scale in recent years. Until 2014, there had been more than 2300km of subway tunnel in China which accounted for nearly three quarters of Chinese urban railway system (Zhang Chen,2015). In some metropolises like Beijing and Shanghai, most of the metro tunnels has already run over 20 years which within maintenance phase. This has brought about plenty of inspection work and maintenance work to guarantee the tunnel under the serviceability limit states. The increase of running mileage of subway tunnels in China has been displayed in Fig 1."

Jan 1, 2016

By A. J. Antony Chettupuzha

During a construction project, it is important to ensure that accurate and pertinent knowledge is delivered on time to appropriate personnel. The criticality of documents exchanged or referred to by various parties, evolves over the course of the project lifecycle. Determining the criticality of documents at different stages of the project can aid companies with managing the flow of information in an organized manner, while providing for the detection of potentially disruptive, erroneous material that could result in delays and costs. Therefore, it is crucial to determine documents which have the potential to disrupt a process (by virtue of being incorrect versions etc.) so that they may be isolated or prevented from entering or interfering with the active flow of information in a project, while also ensuring standard revisions of documents are recognized and accessed accordingly. Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project. Analyzing an EPPM system may yield information about the criticality of certain documents within an activity, as well as isolate characteristics peculiar to documents which can assist in risk mitigation. We propose methodology that identifies such critical documents.

Aug 1, 2013

By David N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in Western Pennsylvania. The coal bed mined is in the Lower Freeport seam which averages 42 inches (1.07m) in height locally. Drainage from the mine is approximately 3.5 million gallons of water per day (13.25 million liters per day). This water deteriorates the mines predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplished by pulling the 6 ton (5443 kg) shields out under their own hydraulic power and transporting them by track over four miles (6437m) co the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1984

By Betty J. Laswell, Gerald W. Laswell

The stepped-up pace of US open-pit and surface mining during the 1970's is a direct response by mining firms and equipment manufacturers to rising costs and declining ore grades. In the race for bigger and more efficient machines, rotary drills have emerged as the foremost leader in primary drilling at major US surface operations. At least 12 different manufacturers now offer rotary rigs in the 102- mm-diam. (4-in.) or greater blasthole size range. With capital investment for the larger units quickly approaching $1 million, the question is asked, "What's been the performance record to date of rotary drill rigs operating in North America?" To answer that question, a comprehensive study of rotary blasthole drills was conducted which qualitatively reveals various problem areas inherent in the rotary drill market and indicates some new directions for improvement.

Jan 6, 1978

By Joseph A. Sopko

The first documented procedures for designing frozen earth structures are over 50 years old, implemented long before the introduction of the Finite Element Method (FEM). Since that time, the development of three-dimensional models has made the traditional and often over-conservative methods relatively obsolete. This paper discusses a new approach that is largely dependent on the analysis of internal stresses with the frozen structure and comparison to frozen soil laboratory tests. A specific design process is discussed related to initial field investigation, laboratory testing, structural and thermal analysis, and performance monitoring. The design results are compared to case histories in the field that verify the procedure. BACKGROUND One of the first documented methods to designing frozen earth retaining structures was by Sangar (1968). Methodical refinements were published by (Harris 1995) and published by the International Symposium on Ground Freezing in 2002 (Andersland et al. 1991). The structural design or thickness of the frozen mass was based on the unconfined compressive strength of the frozen soils. Two simple equations for determining the thickness of a frozen shaft are shown in Fig. 1 and the first two equations below.

Jan 1, 2019

By Youqi Fan

Complicated copper oxalate precursor powder was prepared using ammonium oxalate as precipitating agent in the Cu(II)-C2O42--NH3-NH4+-H2O system. The composition and morphology of the powder are characterized by chemical analysis, X-ray Diffraction (XRD), scanning electron microscope (SEM), infrared spectroscopy (IR). The effects of temperature, copper ion concentration, pH value are investigated. It?s indicated by the experimental results that precursor of copper oxalate is prepared below a critical pH value, whereas the precursor turns to be a complicated copper salt combined with NH3 while over the pH value. Probable chemical formula CuC2O4?x(NH3)?yH2O can be assumed which x and y are relation to experimental conditions. Technological parameters, such as temperature, initial copper concentration and solution pH value, have significant effects on particle size, morphology and dispersion of precursor powder. By controlling certain technological conditions, various morphologies of precursor, pie shape, spindle shape and rod shape can be synthesized.

Jan 1, 2009

Conventional ferronickel smelting has five main steps: Drying, calcination, prereduction, smelting and refining. In the scope of the current work, smelting experiments were conducted using Sivrihisar laterite ores (1.26% Ni) of Turkey. The ore samples previously subjected to drying, calcination and prereduction stages were smelted in alumina crucibles in a laboratoryscale horizontal tube furnace under argon atmosphere. Smelting experiments were performed at 1500, 1550 and 1600 oC. The amount of excess coal used in prereduction step was another variable. Sivrihisar laterite ore is a limonitic one with low MgO composition. Therefore, MgO was added to the smelting charge as a flux. The effects of experimental variables on metal Ni content and slag composition were investigated.

Jan 1, 2012