Search Documents

By Paul H. Johnson

Heap leaching is a simple means of recovering copper from oxide and oxide-sulfide ores. Although this method requires relatively low capital investment, it suffers from low copper recoveries and relatively high acid consumption. The objectives of this study were (1) to determine what factors influence these shortcomings, and (2) to establish a basis of correlation. between laboratory and field testing. The principal methods of leaching copper ores at the present time are heap, dump, in-place, and vat. A number of references are presented in the bibliography on the theoretical and practical aspects of these methods. In the heap-leaching method, crushed or uncrushed oxidized copper ore is placed on a prepared drainage pad. Acid leach solutions are dis¬tributed over the top of the heap, caused to percolate downward through the ore bed by gravity, and are drained from its base. The leach duration is generally a matter of a few months. Dump leaching is used to recover copper from very low-grade oxide-sulfide pit-waste materials. Here again, leach solutions are, percolated downward through a heap. However, in this method, little or no acid is added to the leach liquors, prepared drainage pads are not used and the leaching cycle is generally measured in terms of several years. Leaching agents are usually autogenously generated by the breakdown of sulfide minerals within the dump.

Jan 1, 1970

By R. W. Van Dolah

An investigation was made of the distances over which sympathetic detonation of ammonium nitrate (AN) and ammonium nitrate-fuel oil (AN-FO) might be expected. Large-scale gap tests used two types of AN-FO donor charges in three sizes with AN, both at ambient and elevated temperatures, and AN-FO acceptor charges. Donor sizes were varied to test the validity of a scaling law commonly used in quantity distance tables. The up-and-down experimental design was chosen to determine the 50-percent initiation point efficiently. The acceptor charges were instrumented to indicate initiation and to determine detonation velocity. Other electronic techniques for measuring the rate of growth, stability of detonation, and detonation pressures were employed. Air shock and fragment velocities between charges were measured by electronic and photographic methods, and determination of side-on air-blast pressures and impulse duration were made for about half the shots. Separation distances between donor and acceptor were found to be larger than anticipated both for the AN and the AN-FO. With AN-FO acceptors and a 16-gage steel faced donor, one initiation occurred at a separation of 53 feet or nearly 16-charge diameters; with AN, initiation occurred at 4 to 5-1/2- charge diameters.

Jan 1, 1966

By F. M. Boler

The U.S. Bureau of Mines conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic de stressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 2 ½ -week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 2010

By E Jak, M Shevchenko, E Nekhoroshev, D Shishin

In the field of pyrometallurgy, the presence of multiple molten phases with distinct chemical compositions, such as slags, mattes, speiss liquids, metals and molten salts, is a well-known phenomenon. These phases exhibit strongly non-ideal solution behaviour and are mutually miscible to varying degrees. To describe these complex molten liquids, the Modified Quasichemical Model (MQM) has proven effective and has been applied to numerous binary, ternary and several higher-order multicomponent systems related to pyrometallurgy. In recent decades, the complexity of high-temperature processes has escalated due to increased impurity concentrations in primary ores, the incorporation of recycled consumer products and the integration of metallurgical plants through by-product and waste exchanges. To address these issues, PYROSEARCH laboratory has been developing large 20-component thermodynamic database using a generalised CALPHAD (CALculation of PHAse Diagrams) methodology integrated with experimental investigations. Over the past decade, strategic decisions were made balancing the ability to generate experimental data, prediction power, accuracy, stability of calculations, as well as computational time, which are discussed in the paper. Examples provided for issues of >3 liquid immiscibility, non-ionic behaviour and exaggerated ‘sharp’ enthalpies of mixing in silicate slags, dealing with multiple oxidation states, as well as comparative analysis of pair and quadruplet approximation in MQM.

Aug 21, 2024

By S. K. Sahoo, S. K. Sharma, U. K. Singh, G. S. P. Singh

This research focuses on the strata control issues in a Bord and Pillar depillaring working under the influence of dead load condition of voluminous and fragmented softcover of overburden dump material. It reports the modeling of a mine working through the FLAC 2D software under the Indian geo-mining conditions. The modeling results of an actual mine working under softcover were compared with that under the intact overburden condition to assess the influence of the soft overburden over the depillaring working. The modeling work involved progressive caving of the strata and the cyclic goaf filling following the modelsimulated occurrence of main fall and periodic caving. Mohr-Coulomb Failure criteria along with a simplified strain-softening (MCSS) model was used to study the failure and caving mechanism. Salamon’s compaction model was used to simulate compaction and resultant stress recovery in the goaf material. Comparison of the model findings was done in terms of load on supports, abutment stress, and convergence, apart from the stress redistribution and failure mechanism. The load transfer mechanism of the soft overburden was also studied for an overall understanding of the strata behavior in such workings.

Jun 16, 2020

By A. W. Fahrenwald

Flotation practice in Idaho is now about 13 years old. The advance has been steady during these 113 years. The operators have been alert to take advantage of the newest developments and they have themselves made a constant effort to improve their work. The metallurgical improvements are due to the development of (1) better equipment, (2) better reagents, and (3) better understanding and control of the process. During the eight years the writer has been in this district, there has been continuous experimentation by several companies to improve the ore dressing by flotation methods. Gravity concentration has fought hard to hold its place, and although it is true that gravity processes have been improved during this period, nevertheless, in several of the important mills of the district the few tables that managed to hang on have finally given way. On the straight-lead ores, tables and jigs are still used; and, due to better classification, their hold on this job has been strengthened. Ores of the District The ores of the district are of two general classes: (1) clean lead ores, such as those from the Bunker Hill and Hecla mines, and (2) complex lead-zinc ores. The general impression prevails that the clean lead ores, class 1, are simple and that it is easy to obtain high recoveries and good grade products. This, in a way, is a false impression; there is quite a high percentage of locked middling in these ores at 100 and' 150-mesh sizes. Improved classification preparatory to table treatment of this type of ore has made it possible to segregate effectively a high-grade middling which is further comminuted and floated. The complex lead-zinc ores of the district, of which the ore from the Morning mine of the Federal Mining & Smelting Co. is a typical example, always have presented a difficult problem. It always has been comparatively easy to make a clean lead concentrate, but it never has been possible to concentrate sphalerite with a specific gravity of 4.10 from siderite of gravity 3.88. Also, a large percentage of the galena and sphalerite of this class of ore refuses to separate out until the crushing has been carried

Jan 1, 1928

By E. R. Leeman

INTRODUCTION The first references in the literature to the so-called C.S.I.R. 'doorstopper' strain cell were made in 1964 1,2,3,4. These were the climax of nearly two years of experimental and developmental work with the instruments and the operating techniques involved. Since that time numerous field measurements have been made with 'doorstoppers' and they have been developed to a stage where they are in commercial production and are being supplied to users throughout the world. No detailed description of the latest 'doorstopper' equipment has, however, appeared in print and this paper is written to bring the literature up to date in this respect. The triaxial strain cell was developed three years ago 5, 6, 7 and was first described at the First Congress of the International Society for Rock Mechanics in Lisbon in 1966 8. Since that date laboratory tests and-particularly important-field tests 7' 9 have demonstrated the validity and practicality of the instruments and techniques. These instruments have also been developed to a stage where they have been released for commercial production. In this form they are very different from those described two years ago and a full description of them at this stage seems to be justified. THE INFORMATION SUPPLIED BY 'DOORSTOPPER' AND TRIAXIAL STRAIN CELLS Both the 'doorstopper' and triaxial strain cells were designed specifically to determine the absolute stress in rock using an overcoring stress relieving technique. They were not designed to measure changes in stress. They may, however, be used for the latter purpose provided the glue which is used to stick the strain gauges to the rock is known to possess sufficiently stable strain-time characteristics as not to affect the accuracy of the results during the time the measurements are made. The 'doorstopper' was designed primarily to measure the major principal stress in situations where its direction and those of the two other principal stresses were either known or could be assumed. For example, at great depth in undisturbed virgin ground, it is reasonable to assume that the maximum principal stress is vertical and that the other two lie in a horizontal plane. The borehole in which the 'doorstopper' is installed would thus be drilled in the horizontal plane parallel to one of the minor principal stresses, the direction of which would either have to be assumed or determined as described later. The stresses measured would be the vertical major principal stress and the principal stress acting in a horizontal plane normal to the borehole axis. It is possible, as will be shown later, to obtained the complete state of stress using 'doorstoppers'. In this event, it is necessary to make measurements in three boreholes drilled in any three known directions to each other and relative to a system of three orthogonal axes. The triaxial strain cell was designed to determine the complete state of stress in a single borehole drilled in any direction in any stress field. At first glance it would appear to supersede the 'doorstopper'. This is not necessarily true since there are

By S. F. Shaw

Tars paper is a review of the principal details of cyanide practice in several of the modern plants in America, mainly during the year 1908. Two of the mills, the Goldfield Consolidated and the Vets, Colorado, are not yet prepared to give data, the former having started about Jan. 1, 1909, and the latter not yet being completed. These two mills embody most of the latest methods and are therefore described as far as possible. I. CRUSHING. The principal methods of crushing ores for treatment by the cyanide process are with gyratory and jaw-crushers, stamps, Bryan and Huntington mills, and tube-mills. The first stage is usually done by gyratory or jaw-crushers, in a few cases sup-\

Jul 1, 1909

By Florence Ntsiful, Eric Stemn

Exposure to whole-body vibration has been recognised as an occupational hazard in the mining industry, especially in the operations of earthmoving equipment. Managing whole-body vibration exposures requires periodic measurement of exposure levels to identify priority areas for implementing controls. However, due to different approaches to collecting exposure values, significant variabilities lie in the results. This systematic review is the first attempt to analyse whole-body assessment methods in the mining industry. The aim was to identify how whole-body vibration has been assessed, including the sources of variabilities to improve future research. The PRISMA methodology was adopted for the review and a total of 152 peer-reviewed journal articles were identified. However, only 24 were included in the review, following the application of some inclusion criteria. Descriptive and thematic analyses were performed on the 24 selected articles. Results indicate that whole-body vibration has been assessed as a function of either equipment characteristics, activity undertaken, operator characteristics, measurement approach or the assessment standards. Due to the multifactorial and dynamic nature of wholebody vibration exposures, the variabilities in results are due to the interrelationships between the risk factors of whole-body vibration and the differences in the sample sizes. To identify the sources of variabilities, a comprehensive assessment of all the risk factors, including equipment characteristics, road conditions, operator characteristics, and activity undertaken, is highly warranted. Finally, research gaps and directions for future research have also been discussed.

Dec 21, 2022

By Yao Yevenyo Ziggah, Victor Amoako Temeng, Solomon Evans Kweku Koomson

Tyre hours/life deficit is a major operational challenge facing the mining industry which adversely affects materials production and costs. An accurate forecast of the tyre life is key in addressing this menace. This study for the first time employed the hybrid intelligent technique by utilising three metaheuristic optimisation algorithms, including particle swarm optimisation (PSO), genetic algorithm (GA), and whale optimisation algorithm (WOA), as trainers for the parametric weights and biases to optimise multilayer perceptron neural network (MLPNN) for enhancing prediction of on-site dump truck tyre life in the mine. Four hybrid models known as PSO-MLPNN, WOA-MLPNN, GA-MLPNN, and BP-MLPNN were developed using a total of 157 tyre dataset records obtained from a surface mine in Ghana. In assessing the prediction performances for the models developed, five statistical performance metrics of variance accounted for (VAF), Nash–Sutcliffe efficiency index (NASH), coefficient of determination (r2), mean absolute percentage error (MAPE), and correlation coefficient (r) were utilised. Moreover, ranking, uncertainty analysis and Bayesian information criterion (BIC) techniques were utilised to establish the most effective hybrid model, whereas sensitivity analysis was conducted on the input parameters. Results achieved showed that PSO-MLPNN was the best for prediction because it had the least MAPE value of 1.196% and relatively high values of VAF (99.642%), NASH (0.996), r2 (0.996), and r (0.998). Besides, PSO-MLPNN had the best selection criteria values of 6, 7.1725, and 444.834 for the ranking, uncertainty analysis and BIC respectively. Hence, PSO-MLPNN is recommended for the prediction of on-site dump truck tyre life for the studied mine.

Mar 11, 2024

By C A. Thomas, J C. Eardley, G V. Franks

As valuable minerals are more disseminated, there is a need for low-grade ores to be finely ground to liberate these valuable minerals. However, this has a negative impact on ultrafine mineral recovery as conventional separations processes such as gravity separation are no longer effective. Instead, fine particles can be recovered by froth flotation. Various novel reagents have been introduced along with development in flotation cell designs such as Jameson cell and column cells to improve performance and recovery of ultrafine valuables. This study, on the other hand, aims to recover the fines using a combination of commercially available reagents to selectively flocculate the valuables, so they are large enough to be recovered via conventional froth flotation cells. This technique if successful can be implemented in many existing industries that continue to use mechanical flotation cells that require particle sizes to be 50–150 μm for effective recovery (Ralston, 1992; Batterham and Moodie, 2005). Selective flocculation is not widely implemented in industries mainly due to the inability to float the aggregates ones they are formed and gangue entrapment within the aggregates which consequently affects the grade of concentrate recovered (Forbes, 2011). The major goal is to aggregate the minerals and float the aggregates unlike the more common industrial technique such as reverse flotation of hematite, where the aggregates itself is not recovered via flotation.

Aug 24, 2022

By Leslie McHattie

?Intelligent mine? conjures up a futuristic image of unmanned extractors and loaders working in harsh conditions in a remote lunar landscape. The promise of increasing mine fleet productivity and solving the problem labor shortages in mining regions can certainly be achieved today through remote controlled extraction and automated hauling. The technology is available and it doesn?t seem to be so much science fiction when Google?s self-driving cars hurtle down the freeway. ?Intelligent mining,? on the other hand, implies the application of information technology at every phase of the mining value chain, from exploration and geological modeling to equipment, operations and maintenance, and logistics and transportation. These are really industry-specific, enterprise-class software solutions focused on using information technology to support the business processes of mining and make them more efficient and effective. Overlaying the physical world with the digital or virtual world enables us to model and simulate our assets, giving us the ability to effectively design, build, and ultimately optimize the performance and reliability of our assets throughout the lifecycle. The digital asset, often a 3D model, is created initially during the engineering and construction phase, and is handed over to the operator before the mine goes into operation. Combined with geospatial or geographic information systems, the operator has a complete digital representation of the physical world, which forms the foundation for risk and performance management, along with compliance and regulatory reporting. Laser scanning and positioning technology can be used to create point clouds ? information models consisting of millions of data points ? which enable the visualization and representation of the ?as-operated? reality. But consider that once the mine is in operation, it throws off an endless stream of data in the form of performance and condition data from sensors and monitoring devices on fixed and mobile assets through networks, servers, and services. This ?big data? can be processed and analyzed to spot trends, help predict events, and formulate reliability strategies as early as the design stage (e.g., reliability-centered design). ?Intelligent mining? implies that massive amounts of data augment the reality of the physical mine, plant, and equipment. This embedded intelligence can be used to optimize operational efficiency, increase asset availability and utilization, improve safety and environmental integrity, and maximize return on investment. Lastly, the sweet spot for intelligent mining is seen in the convergence of consumerization and industrialization. The application of ?consumer? technologies that we use every day on our iPhones and Android devices, such as cameras, motion sensors, and positioning in an industrial context, are producing ?immersive? experiences. Overlaying the digital world on the physical world and connecting them accurately through intelligent positioning results in ?intelligent infrastructure,? which is safer and more sustainable. Bentley Systems works with many mining companies and engineering, procurement and construction companies involved in all aspects of mining infrastructure development. In fact, 10 of the top 20 mining companies ranked by market capitalization are users of Bentley software, including all of the top five. In addition, Bentley provides software solutions to the world?s leading engineering, procurement, and construction companies, as well as owner-operators, who design, build and operate the world?s infrastructure. Bentley?s solutions for mining and resource extraction industries help increase the efficiency of capital projects associated with the design, procurement, and construction of mines and processing plants, as well as the operation and maintenance of mining fleet and equipment.

Aug 1, 2013

By Michael J. Friedel

As part of an investigation aimed at mitigating the hazards caused by abandoned mine openings, the Bureau of Mines conducted a series of electromagnetic surveys in the Galena, KS, area of the Tri-State mining district. The application of monostatic ground-penetrating radar (OPR) and inductive electromagnetic methods for detecting and delineating hazardous mine openings and attendant features was demonstrated to be feasible for shallow mine workings (i.e., less than 35 ft) occurring below flat-lying areas. Accurate determinations of depth to a mine roof appeared to be limited to roughly 20 ft using the GPR method. Features such as mine voids, fractures, and zones of subsidence were located beneath the Mainstreet (State Highway 26) site using the GPR system. Both the GPR and inductive electromagnetic techniques satisfactorily located mine openings and pillars at the Hell's Half Acre site. Geophysical interpretations were supported by exploratory drilling and mine maps.

Jan 1, 1990

By R. S. Douglas

THE Granby Consolidated Mining, Smelting and Power Company, Limited, is engaged in the mining and concentrating of copper ores, and, incidentally, in the mining of coal and the production of electric power. The Company has been engaged in these various operations both on the mainland of British Columbia and on Vancouver island for the past forty-five years. This paper will attempt to cover their present operations in the Similkameen mining district of southern interior British Columbia. GENERAL CHARACTER OF THE DISTRICT The Interior Plateau in southern British Columbia ranges in elevation from 3,000 feet to 6,000 feet. In the vicinity of Princet0n, a depression in the Plateau forms a well defined basin which is floored with a series of nearly flat-lying Tertiary sediments containing some workable seams of lignite. From this basin, the upland surface rises gradually t0ward the south, from an elevation of 2,000 feet at Princet0n to 4,000 feet at Copper mountain, and 6,000 feet in the upper parts of the Similkameen basin, where it merges into the rugged and diversified t0pography of the Cascade system, with glacier inhabited peaks rising to over 9,000 feet. The valleys of Similkameen river and its tributaries are wide, having flaring sides and gentle slopes, and are separated one from another by subdued rounded spurs, of which Copper mountain is typical. The drainage of this district is taken care of by Similkameen river and its larger tributaries, such as Pasayten river, and Wolfe, Friday, and Whipsaw creeks. The name Copper mountain is applied to a gently arched, nearly flat-topped spur between the deep valley of Similkameen river to the west and the shallower valley of Wolfe creek tO the east. The mountain is appro-priately named from the number of copper deposits occurring on its sides and summit, some of which have been developed int0 an important producer, known as the Copper Mountain mine.

Jan 1, 1943

By C. Stamberg, W. McGuire, R. C. Carlson, L. W. Vollmer

"The selection of materials and pre-cautionary measures for handling natural gas and condensate containing aqueous hydrogen sulphide are presented. Based on the results of a pilot production test and laboratory studies, together with several years . of operating experience, it was found that the behaviour of materials in sour gas environments can be predicted sufficiently accurately for engineering purposes.The selection of proper materials is essential for preventing sulphide-stress cracking. Where high strength materials are not required, low car-bon steel is used. Components requiring high tensile strength and hardness characteristics should be made from K-monel or properly heat-treated carbon-manganese-molybden-um and AISI 4140 steels. Welded connections are a potential source of sulphide-stress cracking. Consequently high quality welding and strict inspection are suggested as the most economical precautionary measures available.A maintenance program based,. where possible, on visual inspection of equipment and/or test spools located at strategic points should be used to follow weight loss and putting corrosion in sour gas environments. If severe weight loss or pitting corrosion is encountered, inhibitors have been found to be an effective deter-rent."

Jan 1, 1960

By L. R. Burdick, R. Wiggers, J. F. Berkley

"INTRODUCTION On February 23, 1944, Solid Fuels Administrator Harold L. Ickes stated that the existing fuel shortage made it necessary to utilize a great surplus of freshly mined anthracite ranging in size from Barley (No. 3 Buckwheat) downward through the smaller sizes. As a part of the program to increase the use of such coal, field trials of mixtures of bituminous slack coal and anthracite Barley were made on industrial-size stokers at many fuel-burning plants. The following covers the test information it was possible to accu-mulate during the work of initiating the use of these mixtures at the plants.SUMMARY AND CONCLUSIONSField tests of various mixtures of bituminous slack coal and anthracite Barley on industrial-type stokers show that the use of such mixtures is very practicable and that it is possible to change and usually to adjust to an improved condition the characteristics of a fuel bed of eastern bituminous slack coal by the addition of proper amounts of anthracite. The improved uniformity of the fuel bed of single-retort stokers makes possible less manual attention to the bed. Air flow through the fuel bed is affected.Smoke is decreased. In general, the fly ash and also the unburned combustible in the fly ash and refuse are increased. Clinkering in the fuel bed is generally lessened. The peak-load carrying capacity of the stoker is definitely affected, usually adversely for the higher percentages of anthracite."

May 1, 1946

By Arthur Dubé

An account is given of the developments brought about in the last fifteen years by metallurgical research in the field of heat treatment of steels. The practical aspects of these developments are especially emphasized. Methods of representation of the phase-change during austenitizing and sub-critical transformation of austenite are described and the importance of time-temperature-transformation charts for the planning of heat treatment cycles is shown. Special copies such as retained austenite and internal stresses developed on quenching are also discussed in some detail. Due to the interest shown currently in these problems, it has been thought advisable to describe briefly the underlying principles and present some of the results already available.

Jan 1, 1945

By C A. Foss, D A. Clark, D Hillan

While magnetic surveys are the most common geophysical method used in mineral exploration, magnetics and geology remain to be fully integrated quantitatively in iron ore provinces. Although high-resolution aeromagnetic data has been collected over prospective areas of the Hamersley Province, much of the information in the data sets has hitherto not been fully exploited due to a lack of suitable interpretation methods. Recent advances in the processing and modelling of magnetics in highly magnetic terrains, constrained inversion and 3D visualisation and understanding the magnetic properties of banded iron formations and iron ores potentially create the capability to generate realistic 3D mapping of magnetite and hematite concentrations over large areas. Initial processing of conventional total magnetic intensity data produces true potential field maps that are unaffected by local perturbations of the regional geomagnetic field direction by intense local anomalies. The true potential field can be converted into vector and tensor components, each of which emphasises different structural features of the geology. Scalar quantities derived from these components simplify interpretation, using new methods, developed by CSIRO and elsewhere, that are less sensitive to magnetisation direction. Preliminary interpretations allow interpolation between mapped units and structures and evaluation of remanence and anisotropy effects. Accurate modelling requires rigourous treatment of self-demagnetisation and magnetic interaction effects. Semi-automated constrained inversion, combining magnetics with available geological information and other geophysical data, can be utilised to generate models of disposition of major magnetic units and the 3D magnetisation distribution within them. The final stage of interpretation is to exploit the understanding of magnetic properties (susceptibility, anisotropy and remanence) developed over many studies by CSIRO, the University of Western Australia and others to convert the interpreted magnetisation distributions into 3D maps of magnetite and hematite contents, which are the quantities of direct exploration interest.CITATION:Clark, D A, Foss, C A, Austin, J and Hillan, D, 2015. Three-dimensional mapping of magnetite and hematite concentrations from reprocessing of detailed aeromagnetic data, in Proceedings Iron Ore 2015, pp 229–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By N Tyson

Throughout Australia and the world, there have been in recent years a number of incidents involving the reaction of ammonium nitrate based explosives with ground containing certain types of sulphides. This paper presents a comprehensive strategy designed to identify, assess and mitigate the risks involved with blasting in areas of reactive ground. Undertaking blasting in reactive or potentially reactive ground involves a degree of risk, the level of which is dependent upon the controls in place for specific sites; this in turn depends upon the degree of sound reasoning and judgement behind the implementation of these controls. Implementation of controls to minimise the risk of incidents also involves a measurable increase in production and blasting costs. To achieve a balanced solution to this matter, decision-makers need to understand how the risks eventuate, how they should be evaluated, and how control measures reduce the risk. Also required is an understanding of how the problem affects the economics of the operation, and the magnitude of this effect. It is the aim of this paper to provide a structured approach to gaining this knowledge, so that mine management, the workforce and explosive suppliers may jointly develop more effective economic and safe blasting systems for potentially reactive ground. Using a combination of fault/event tree risk assessment and semi-quantitative analysis, a structured approach to dealing with the issue will be illustrated.

Jan 1, 2001

By S. A. Scott

In 1913, potash mineralization was recognized at a depth of over 7,000 feet in an oil-well hole (Norcanol's Radville No. 1 well) drilled near the town of Raddlle, Saskatchewan. Although, at this depth, potash is not considered mineable by conventional underground mining methods, this discovery shed the first light on the potash deposits of Saskatchewan in much the same manner as oil-well drilling was responsible for the first discovery of potash in the Carlsbad Basin of New Mexico in 19:25. The discovery near Radville alerted the oil-well geologists and, as a result potash mineralization was recognized in the Verbata No. 2 well, near Unity, Saskatchewan, in 1946. The mineralization, which was at a depth ?of 3,466 feet, graded more than 20 per cent K20 over a thickness of eleven feet. This discovery, as its depth, thickness and grade were all amenable to mining,

Jan 1, 1963