Search Documents

By S Van Duin, I Porter

This paper discusses how advanced manufacturing technology (AMT), which is fundamentally reliant on and developed via multi-disciplinary skills, has benefitted non-mining industries, and what lessons can be derived from this experience to benefit the mining industry, particularly underground coal mining. Examples of AMT use in æconventionalÆ industry, some drawn from the more than 25 years experience in many different industries of the Automation and Robotics team at the University of Wollongong, are described to show typical benefits, risks and opportunities expected in using AMT. Applying AMT to mining brings many unique challenges and this paper expands on these and then provides practical examples of how a multi-disciplinary team can develop new processes and systems leading to productivity, safety and other benefits for underground coal mining.

Sep 26, 2011

By Seong-Taek Lim

Recently, 7xxx aluminum alloys have been evolved into new variants for thick semiproducts which have low amount of 2nd phases and low quench sensitivity. Commercial 7xxx alloys, especially in the thick forgings made of big ingots, often entail microstructural inhomogeneities and concurrent poor mechanical properties due to limited heating ranges and slower quench cooling. In this study, high strength aluminum alloy 7175 and 7050 are adjusted as an attempt to control the equilibrium phases (M-, T- and S-phase) to have optimum microstructure for the thick forging applications. The effects of the relative content of (Zn, Mg, Cu) on the evolutions of the coarse equilibrium phases, hardening response and resultant mechanical properties are investigated. Equilibrium phases (M,T,S) are evolved depending on the constitutional effect, primarily the change of Zn:Mg ratio, and cooling rate following solutionizing. The formation of the T- and S-phases is effectively controlled, and M-phases are homogeneously precipitated in the adjusted (dilute and high Zn:Mg ratio) alloys. It provides extended heating range and lower quench sensitivity than conventional alloys. The attempts ensure the microstructural homogeneity and improved properties, and is expected to be uniquely applicable in 7xxx thick forgings.

Jan 1, 2004

By Z. Hyder, A. Urquidez

"INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is located approximately 26 miles southeast of Carlsbad, New Mexico and is the nation’s first underground geologic repository for transuranic (TRU) and TRU-mixed waste (see Figure 1). The WIPP facility was opened for operation in 1999 when the first TRU waste shipment arrived at the WIPP facility for disposal.WIPP facility does not employ typical production aspects of a conventional mine. Instead, the mining focus is on the quality of the excavation to ensure safe disposal of TRU and TRU-mixed waste (Walls, 1991). GEOLOGY WIPP underground repository is mined within a 2,000 feet-thick bedded-halite formation (Salado Formation) (see Figure 2). The WIPP underground repository is located approximately 2,150 feet beneath the surface near the center of the Salado Formation. Geologic criterion and site-selection factors evaluated for the selection of the repository included topography, depth, thickness, lateral extent, lithology, stratigraphy, structure, erosion, dissolution, subsidence, surface water, aquifers, hydrologic transport, climatic fluctuations, manmade penetrations (U.S. Department of Energy, 1980).FACILITY DESIGN Profit did not play a major role in the WIPP’s conception like in a conventional mine. This was due to the extensive amount of additional regulations and safety controls that had to be built into the WIPP facility. Since it is nuclear and hazardous waste disposal facility, it must meet certain federal and state requirements for TRU-mixed waste. One of the major regulatory drivers for the WIPP facility is defined in the WIPP Land Withdrawal Act (LWA). One of the requirements in the WIPP LWA requires the DOE to submit documentation of continued compliance with Title 40 CFR Part 191, Subparts B, and C. These standards are regulated by the Environmental Protection Agency (EPA). The DOE must submit documentation of continued compliance (recertification) with these regulations every five years. In addition to the LWA, the Resource Conservation and Recovery Act (RCRA) is another major regulatory driver for the WIPP facility. Since the WIPP facility is categorized as a “Miscellaneous Unit” under 40 CFR, it must meet extensive environmental performance standards. These standards are defined in the WIPP Hazardous Waste Facility Permit (HWFP). The HWFP defines the terms and conditions that the Secretary of the New Mexico Environment Department has determined necessary to protect human health and the environment (U.S. Department of Energy and Nuclear Waste Partnership LLC, 2015)."

Jan 1, 2017

By S. Aram

Concrete reinforcing requires coordination among many roles: structural engineer, estimator, detailer, fabricator, installer and others. The methods used to define and represent concrete reinforcement elements and assemblies in building information models is crucial in determining the efficiency of sharing data among BIM platforms and the effectiveness of using the carried data in production planning, fabrication and site work activities. Starting from the information items that are required to be provided by BIM platforms, as defined in earlier work, we have developed the Industry Foundation Classes (IFC) bound Concepts and Model View Definitions (MVDs) for concrete reinforcement. Furthermore, in coordination with software developers, we propose guidelines for best practices for concrete reinforcement modeling. Implementing these guidelines by software providers will improve reinforcement modeling with regard to various aspects of reinforcement products like geometric representation, placement, and property specifications. The proposed approach is selected as a way to improve functionality of the shared data for production planning, fabrication, project management, and site activities. Guidelines for assigning information to rebar type and instance definitions as well as to rebar elements and assemblies are provided. An efficient method of sharing geometry and property sets among rebar instances of a rebar array is also defined.

Aug 1, 2013

By Sanat Talmaki

Construction and mining worksites pose unique challenges to workers and equipment operators due to their dynamic and unstructured nature. Narrow haul roads, crowded work spaces and presence of workers and equipment in close proximity, combined with large blind spots and overall poor visibility afforded to operators lead to collisions and run-over-type accidents between equipment, workers, and other entities that may be present on the jobsite. Operations that involve machine-infrastructure interaction, particularly in the case of concealed infrastructure such as excavation and drilling lead to unintended strikes between the equipment?s end-effect or and the infrastructure. Such accident-prone scenarios can be avoided by providing operators with real-time feedback and warnings using 3D visualization and proximity monitoring of the entities present in the equipment?s vicinity. Thus the jobsite in the real world is abstracted and represented in a 3D virtual world. However, this requires the ability to create a seamless link between real-world sensors present on the equipment and/or the jobsite and the virtual environment. This paper describes a non-restrictive acquisition allocation framework that allows position and orientation sensor streams from construction and mining job sites to be used for updating 3D virtual scenes in real-time for providing vital collision avoidance warnings to equipment operators.

Aug 1, 2013

By T. Suzuki

Acid leach liquors from spent lithium-ion batteries employing lithium cobalt dioxide (LiCoO2) as a cathode active material contain valuable metals such as cobalt and lithium, as well as common metals such as aluminum and copper. The objective of this study was to develop a hydrometallurgical process providing a high selectively between aluminum, cobalt, copper, and lithium from hydrochloric acid solutions. Batch experiment results showed that selective hydroxide precipitation approach was not suitable because a significant amount of cobalt and lithium was co-precipitated with aluminum and copper hydroxides. In contrast, batch experiments and the subsequent data analysis indicated that the sequence of solvent extraction circuits using PC-88A, Acorga M5640, and tri-n-octylamine (TOA) extractants effectively separates four metals of interest. In the first circuit of the proposed process, copper was selectively extracted by Acorga M5640 at the pH 1.0-2.0. Aluminum, cobalt, and lithium remain in the aqueous phase. In the second circuit, aluminium is selectively extracted by PC-88A at pH 2.0-2.5. For the separation of remaining cobalt and lithium, Acorga M5640 provided higher separation efficiency compared to PC-88A single extractant and PC-88A/TOA mixed extractant. However, the stripping efficiency of cobalt from the Acorga M5640 organic phase was found to be low (less than 10 %). Therefore, PC-88A/TOA mixed extractant rather than Acorga M5640 is an advisable choice for the separation of cobalt and lithium. Keywords: spent lithium-ion secondary batteries, solvent extraction, lithium, cobalt

Sep 1, 2012

By D. M. Ziebarth

"Normal sequence of operations to develop a new underground mine is: construct and outfit headframe for shaft sinking, sink shaft, construct and outfit shaft sump, develop shaft station and shaft bottom steel. In an effort to reduce the overall project schedule, an innovative plan was developed to install service shaft steel below station level, prior to the completion of the shaft sinking effort. To better evaluate the construction of this substantial steel tower, a preliminary constructability evaluation was conducted, including the best method of supporting the main tower; from the bottom, middle or top of the tower. The design criteria and plan involved: •,Develop access from existing service shaft, 25 km underground •,Use of materials to maximize strength while minimizing corrosion exposure •,Estimating the location of the shaft centerline •,Over excavating the station and shaft below station to allow future shaft steel repositioning •,Designing the tower steel for modular installation •,Incorporate commissioning considerations, such as suspension of the cheese weights during steel installation •,Provision for covered stair access to shaft bottom •,Enclosed shaft envelope with open panels to allow visibility and ventilation The design approach was innovative and this paper will describe the design principles and challenges encountered while providing insight into the solutions developed and implemented; especially the modular construction and installation methodology. INTRODUCTION In an effort to expand the mining operations, a plan was developed to construct a new service shaft closer to the new mine workings and convert the existing service shaft to a production shaft at the Potash Corporation of Saskatchewan Inc. (PCS now Nutrien) Rocanville Potash mine in southeast Saskatchewan. The new service shaft required a multi roped friction hoist operating a cage / counterweight, rope guided conveyances to support the operational requirements. The service shaft is an integral part of the mining infrastructure as it provides access to the underground workings, transport personnel and materials underground for operation and maintenance of the mine. The shaft also allows for services required for safe operation of the underground mine, power supply, controls, communication, dewatering and fresh water supply."

Jan 1, 2019

RME has a vision for a new mill operational paradigm made possible by RMEÆs fast, safe Mill Relining System. This vision can be moved forward into reality at any time with or without guidance from recent development in measurement and predictive modelling tools.Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by optimising liners for life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the linersÆ wear life. RMEÆs proposition is to design new liners for maximum commercial performance. This may mean more frequent changes of liners but with liners designed to yield optimum grinding, metallurgical and profitability performance. In other words, mill liner profiles and mill relining speed become key operational controls and not simply æmust doÆ maintenance functions. Taken to the extreme, liner profiles may prove capable of ætuningÆ a grinding plant for maximum profitability in any metal price environment. This paper provides an update regarding RMEÆs fast, safe Mill Relining System technologies and outlines RMEÆs vision of a æliner profile versus profitabilityÆ model as a function of metal price, developed intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2006

By Ken McIntyre, Trodel Wolf-Dieter

"Sirius Minerals is a UK based fertilizer development company focused on advancing into operation its polyhalite project in North Yorkshire, England. The operation is known as the Woodsmith Mine which has an estimated 2.7 Billion Tonnes of reserves and is currently in the construction phase. DMC Mining Services was selected to carry out the construction of four shafts for the project, a production shaft of 6.75m diameter to a depth of 1594 m, a ventilation shaft of 6.75 m diameter to a depth of 1565 m, and two additional shafts to support the construction of the material transport system (the MTS and Lockwood Beck intermediate) to 360m in depth for servicing the underground conveyor network for transport of product from the mine site to the costal port facilities located at Teasside. This paper will review the status of the project to date and the innovative approaches that DMC is utilizing to ensure a safe and successful shaft sinking project. INTRODUCTION The Woodsmith Mine in North Yorkshire is a Sirius Minerals-owned deep potash and polyhalite mine located near to the hamlet of Sneatonthorpe, Whitby in North Yorkshire, England, approximately 75 km east of York. The area of interest is more than 700 km2. The £3.2 billion project is to develop the Woodsmith Mine to extract polyhalite, and a tunnel system to transport it to a materials handling facility and harbour at Teesside. The site is the world's largest and highest-grade deposit of polyhalite and is expected to produce 20 million tonnes of polyhalite, potash and POLY4 per annum, as well as create over 1,000 direct jobs and many more indirectly. It has the potential to generate over £2 billion of annual exports for the UK. As the project will require mining to be undertaken in the North York Moors National Park, many objections were raised about the mine. Sirius Minerals has gone to great lengths to ensure that the project is sensitive to the local landscape, including: mineshaft head frames that will be positioned below ground to reduce their visual impact; surface buildings will be kept to a minimum; and the entire site will be landscaped and screened by existing woodland to blend in with the surrounding area. The project will also abide by strict environmental limits which govern our activity during the construction phase."

Jan 1, 2019

By M Andrew, H Reynolds, R Mills

As the global mining industry continues to grapple with ‘black swans’ (high consequence / low frequency events) for health, safety and environmental losses, the focus is shifting from risk assessment of these events to risk management using selected purposeful controls that reduce the risk.Fundamental to critical control management (CCM) is a soundly based rationale for selecting the right controls for each and every risk. The approach should be based on a thorough understanding of the dynamics of the event: What causes it? How frequently will it occur? How likely is the consequence to be realised? This is typically done through a bowtie and methodical numerical risk analysis. Core to this step, then, is the structure and content of the bowtie; specifically, the analytic architecture that is used to construct the bowtie. Different architectures yield different constructions, and bowties are no different.Although bowties for operational health and safety (OHS) hazards appear to have a common architecture, they are not generic. It is important to stress that they contain site specific information, are prepared by site based operational teams, and vary from site to site to reflect each site’s operational conditions. They are often a product of the knowledge and understanding of the operational teams involved, may be prone to human error, and potentially miss latent hazards that may have been embedded early in the planning, design or construction phase of a mine or facility, or within the mining equipment. Overcoming these deficiencies through constant re-evaluation of the risks, and challenging the content on the bowtie will help to minimise the chance that something will be missed.This paper will cover key themes in bowtie architecture, introduce the concept of barrier models for high consequence event (HCE) bowties and present a relevant case study to illustrate the issues that determine quality in bowtie construction and critical control (barrier) selection and management.CITATION:Mills, R, Andrew, M and Reynolds, H, 2016. Can we stop a black swan breeding? Advances in bowties and critical control management, in Proceedings International Mine Management Conference, pp 105-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Bahjat Khoshaba, Bern Klein, Haixing Yan, Libin Tong, Andrew Bamber

"When a conductive or magnetic particle was put into an electromagnetic field introduced by an electromagnetic sensor, the particle can influence the electromagnetic field which can be used to characterize this particle. The electromagnetic technology based on eddy current theory was explored to investigate its potential in both the separation of minerals and the pre-concentration of a base metal ore. Samples tested in the study included the minerals obtained from Ward’s Science and the low grade copper ore particles obtained from Mount Polley Mine. The effects of mineral type, sensor frequency, particle size, particle position on the sensor surface, and particle lift-off on the magnitude and phase of the electromagnetic spectra were investigated. The electromagnetic spectra of various minerals show that it is possible to separate chalcopyrite or magnetite from tested minerals, simply based on the magnitude of the spectra. The spectra of the ore particles were determined by the mineral in the particles with the strongest signal. The effect of the pre-concentration of the low grade copper ore is determined by the association of chalcopyrite with magnetite. Direct sorting is the mechanism in the separation of mineral particles, while indirect sorting is the mechanism for low grade ores.INTRODUCTIONSensor-based sorting technologies include radiometric, X-ray transmission, X-ray fluorescence, near infrared, photometric, inductive, microwave heating and so on. Sorting not only discards barren rocks away from the concentrator but also recovers metal bearing that would be lose to the waste dump. The benefits of pre-concentration using sensor-based sorting are achieved on reduced energy consumption for comminution and reduced water usage on a volume per weight of metal basis (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Kleine & Wotruba, 2010; Knapp, Neubert, Schropp, & Wotruba, 2014; Kobzev, 2014; Lessard, de Bakker, & McHugh, 2014; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013). Amongst others, high frequency electromagnetic sensors were developed for ore sorting at MineSense Technologies Ltd. and are subject of this paper. Improving the understanding of ore heterogeneity is the basis for developing a successful semi-bulk or bulk sorting systems by incorporating the sensors in the material handling equipment (MineSense Technologies Ltd., 2016). The present study focuses on the bulk sorting potential and bulk sorting mechanisms of the electromagnetic technology in the pre-concentration of minerals or ores."

Jan 1, 2016

By N. Edmonson

Apart from its role as an essential input to a wide array of agricultural chemicals and industrial processes, sulfur is interesting in that its supply involves competition between primary product and by-product. This general production structure is found repeatedly among markets for metals and other industrial minerals, and research results from the sulfur market potentially carry over to other markets with similar structures. The purpose of this paper is to present an analysis of the recent and prospective market for sulfur. The analysis will rely heavily on simulation using a comprehensive model of the North American sulfur market developed by the author. A brief description of the model is offered by way of introduction

Jan 1, 1993

By Osvaldo A. Bascur

Standards and Technology for bringing information at the desktop has greatly evolved in recent years. The benefits to be realized depend on how these new tools are embraced at the performer level. A key operating challenge is to ensure collective effort is geared towards the most efficient achievement of identified operating and corporate objectives. Presentation, application and data repository modular software are emerging in successful client server applications. The industrial desktop emerges as the new tool for continuous improvement and innovation in industrial operations. Here, process information, reliability maintenance, process simulation, production schedules, performance monitoring are integrated using Microsoft enabling tools at the desktop. A workflow model is presented to assist in implementing a strategic information system in metallurgical plants.

Jan 1, 1996

Ground falls (roof and rib) have historically been responsible for nearly 50% of all fatalities in bituminous underground coal mines. In recent years, the number of some annual ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, the twin disasters at Crandall Canyon in 2007, in which nine miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990s, these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents since 2005. Progress has also been made in pillar recovery, where there has been just one fatal incident since 2005. On the other hand, more than 300 miners continue to be injured each year by rock falling from between supports and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities available technologies such as roof screen, rib bolting and inside control roof bolters could reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety.

Jan 1, 2011

Mineral processing is an energy and water intensive activity. Mill comminution equipment usually has high energy requirements which necessitate extensive cooling to remove heat. Cooling requirements are typically 10% to 20% of the comminution energy. If there is an adequate supply of suitable water, open water-based cooling systems are the simplest, cheapest and most energy efficient cooling method available. This paper describes a method to determine the water demand for open water-based cooling systems at a plant and to determine whether the mine has sufficient water to meet that demand.

Jan 1, 2014

By C. Horstmann, D. Andreo, G. Barthold

"The concept of large single line grinding circuits provides a valid answer in project feasibility studies by reducing capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational aspects, in terms of higher and greater process stability, and reduced operational costs mainly due to the associated lower maintenance expenditures. However, concerns exist in the minerals industry on whether large single line grinding could reduce the overall concentrator plant availability. The mechanical design and integrity, the mill and gearless mill drive integration, as well as assets management aspects of this type of equipment are the key to guarantee successful availability records. Together with an overview of the added value provided by large single line grinding circuits, this paper focuses on risk mitigation strategies during mill and gearless mill drive integration, as well as on the design of the equipment itself, for the key aspects which could put at risk the operations availability.INTRODUCTIONDespite a large long term demand for commodities, the mining industry has never faced complex challenges as it is doing today. Decreasing high-quality and accessible deposits, declining ore grades in existing mines, shortages of electrical energy (e.g. in Chile) and an aging workforce are the most significant among the megatrends affecting our industry. In addition to this, flat underlying commodity prices and high price volatility are currently posing strong requirements to miners when entering into the process of approving investments.Nowadays to get projects financially approved (optimizations, expansions, new plants), capital expenditure has to be reduced, as observed up to 30% compared to the last decade, and at the same time the plant design has to be such to demonstrate that operating costs will also be significantly lower than in the past.When it comes to the concentrator plant, the concept of large single line grinding circuits provides a valid answer in project feasibility studies by significantly reducing the capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational costs, in terms of higher and greater process stability and reduced maintenance expenditures."

Jan 1, 2016

By Peter Scales, Ricardo Jeldres, Fernando Concha, Pedro Toledo, Shane Usher, Anthony Stickland

The impact of several electrolytes present in seawater on the rheological properties of flocculated mineral suspensions was assessed using the creep test. Flocculated suspensions were obtained by adding polymer flocculant to a cylinder of mineral suspension and aggregating the suspension using the plunger method. The suspension was allowed to sediment and the supernatant liquid decanted prior to tests for the viscoelastic properties of the resulting sediment. The solid used was alumina AKP-30 both, below and above the isoelectric point. The polymer used was AN934SH, an anionic flocculant with high molecular weight. Salts analyzed were MgCl2, CaCl2 and NaCl, known as water structure makers, and KI and KCl, known as water structure breakers. A high salt concentration of 0.5 M was used to approach the ionic strength of seawater. For both pH’s studied, the sediments demonstrated a viscoelastic non-linear behavior observed as a non-linear relationship between yield strain and applied stress. In the absence of flocculant, it was observed that the viscosity and yield stress of a suspension increase in the presence of structure maker salts for the case of both silica suspensions and alumina suspensions. These results were explained using hypernetted chain statistical mechanics models describing the interaction of ions with solvated surfaces. In contrast, with the presence of flocculant, the shear yield strain of alumina suspensions increases with the breaker character of the salts, however, this result has been explained by an extension of the results from the models. The work has significant implications for the flocculation of mineral suspensions in the presence of seawater.

Jan 1, 2014

By N Taylor, P Hewitt

The Northern Beaches Storage Project (NBSP) is part of Sydney Water’s SewerFix™ Program to improve the wastewater system and protect public health and the environment. It was built by the SewerFix Wet Weather Alliance (the Alliance), a partnership between Sydney Water, RPS, MWH, Parsons Brinckerhoff and United Group Infrastructure.The project temporarily stores excess wastewater diverted from the Narrabeen Submain during wet weather. The project considered a below-ground storage facility, which involved constructing a deep tunnel from Brookvale to Fairlight, connecting into the Northside Storage Tunnel and a storage tank, which was subsequently adopted and constructed.The storage tank scheme included a pumping station and inlet and outlet pipes installed by microtunnelling. The storage tank site is in the Brookvale industrial area situated in an area of deep marine sediments overlying Hawkesbury Sandstone at about 30?m below ground. Microtunnelling for the inlet pipe was conducted from a 12?m deep jacking shaft. The jacking shaft and 14?m deep pumping station excavations were carried out from within secant pile earth retaining structures adjacent to existing buildings.Construction activities had the potential to cause settlement of the adjacent buildings. During excavation and microtunnelling the water ingress, adjacent groundwater level and settlement of the adjacent buildings were monitored. The monitoring data was assessed against an action plan, which modified construction activities as required to minimise the risk of damage to buildings from settlements caused by lowering of the groundwater table outside the excavations. The secant pile construction, excavation, microtunnelling and pumping station construction proceeded without incident or damage to adjacent buildings.This paper highlights that tunnel/underground options should be considered during options development, describes the original storage tunnel scheme and presents details of the successful microtunnelling and deep shaft construction adopted on the NBSP.CITATION:Taylor, N and Hewitt, P, 2014. Tunnelling on Northern Beaches Storage Project, Sydney, to improve water quality, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 451–458 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Barry Beith

This report details a study which was designed to assess the effect of retroreflective material on detection and form recognition of workers in the mining environment. Further, the study attempted to determine an optimal configuration of retroreflective material with respect to amount and placement on the body to facilitate detection and form recognition. The study involved a one-fifth scale simulation of the perceptual task found in the underground low seam coal mine. Four different configurations of reflective material were presented in various body positions, common to low coal miners, at three different locations in the visual field, i.e., 10, 25, and 45 degrees from focal line-of-sight. All reflective configurations significantly improve detection and form recognition over configuration (cap only) worn by miners. As the amount of reflective material increased, accuracy also tended to increase. Based on the configurations investigated by this study, the Armband configuration (i.e., refectorized armbands, belt, self-rescuer and battery pack) was determined to be optimum. It is recommended that an actual field evaluation be made using the Armband configuration to establish if simulator results are generalizable to the underground mining environment.

Jan 1, 1980

By H. B. Oblad

Coal/pyrite fines were froth floated in a laboratory cell to examine the rate of pyrite recovery during conventional coal flotation. The effects of collector, particle size and carbon to total sulfur ratio on the kinetics of recovery were investigated. These data coupled with microscopic examination suggest that miniscule amounts of coal that remain attached to the pyrite surface affect the rate of flotation of pyrite.

Jan 1, 1985