Search Documents

By D. S. van Vuuren

Titanium bearing resources can selectively be chlorinated at temperatures below 200°C if the Ti02 in the feed is nitrided before chlorination. However, the nitriding reaction is highly endothermic, requires highly reducing conditions, is only thermodynamically favourable at elevated temperatures, and is affected by mass and heat transfer restrictions. At the required processing conditions, problems might also be experienced with sintering and with melting of slag forming components in the raw materials. A test programme was undertaken to study the effects of raw material type, temperature, gas composition, bed depth, carbon to raw material ratio and residence time in order to simulate conditions required for scaling up a nitriding process. In contrast to previous experience with low-grade titanium-bearing slag containing about 30% Ti02, ilmenite and chlorinateable slag do not form melting phases under the studied nitriding conditions and hardly sintered at all. Both feed materials can readily be nitrided with conversions in excess of 90% at temperatures around 1300°C and using bituminous coal as reducing agent with fixed carbon in excess of 1.1 times the stoichiometric requirement. The conversion decreases as the bed depth of the feed material increases and the N2/CO ratio in the gas decreases. Analysis of the relative rates of mass and heat transfer into the reacting beds of ilmenite and slag showed that the heat transfer rates are more limiting than the mass transfer rates. In order to increase the throughput that can be achieved in a kiln, it would be necessary to take special measures to enhance the heat transfer rates into the mass of reacting material. One such a measure is to pre-form the mass of reacting material into thin-walled, hollow brick shapes prior to introducing it into a kiln. Depending on bed depth, temperature and N2/CO ratio, required residence times in the high temperature zone of the kiln can vary between about 6 and 10 hours. Keywords Titanium dioxide, titanium nitride, carbo-thermic, reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By C. Schuffeneger

"The design of SAG milling circuits for mining projects requires the incorporation of the energy consumption considerations and the evaluation between different flexibility-adding options to absorb the time-dependent variation in the ore lithology. In order to expand the focus of the engineering design, a higher level of deepness and quality in the baseline information must be achieved to elucidate all of the constraints on throughput, energy consumption and product quality generating a design optimization consistent with an integrated vision of the process. This paper presents a review of a collection of typical examples of the copper and gold mining project in the Chilean Andes, in which both process and energy efficiency criteria are considered when the focus is to deliver an integral solution that incorporate those areas in the design. The intensive use of energy in the SAG milling, the process continuity and the quality of the product are a function of the proper design and selection of grinding equipment and plant layout, aligned with the mining plan and associated with projected future expansions and production increases.INTRODUCTION Autogenous and Semiautogenous grinding technology, large diameter and short length mills, begins with the Handsel design. During the decade of 1930’s, Handsel-Hardinge studies led to cascade mill development. Nowadays, 80 years later, continuous improvements in design and technology have been conducted to a completely new generation of gearless SAG mills that have led to an increasing capacity at the concentrator plants. Considering the existing alternatives, SAG mills are the most implemented option for the grinding circuit today. This work presents a review of the SAG mill implementation parameters and circuit considerations and its correlations in the most recent projects in Chile with an ore treatment capacity above 50 ktpd since the decade of the 90’s up to now. From this period, the tendencies will be analyzed using project design data. Based on process design information, the recent SAG mill history in relevant projects related to the new generation of commercial SAG mills, technical associated considerations and performance will be discussed. Circuit selection based on energy utilization will be revised to bring up a more holistic perspective on the SAG mill circuit design concepts. As is now well known, the heart of every concentrator plant are the grinding mills. Higher demands on throughput, availability and power consumption optimizations require not only high performance electrical equipment but also a well selected grinding circuit. The energy efficiency issues associated to the circuits design will be reviewed."

Jan 1, 2012

By C. O?Connor

With ever-increasing global demand for mineral resources, numerous mines are moving towards developing and mining deeper, more complex and lower grade ore bodies. In many cases, mass mining methods (e.g. block caving) are being considered to deal with deeper, lower grade deposits. The body of practical knowledge, however, related to the impacts mass mining methods have on the surface environment in terms of rock mass response, subsidence, etc., is limited, imposing both economic risks to the mine and safety risks to mine personnel. This paper presents the framework for and preliminary results from a large collaborative research initiative between Diavik Diamond Mines, Rio Tinto, the University of British Columbia (UBC) and Simon Fraser University (SFU). The project involves the integration of available subsidence, rock mass, mine operation and monitoring data, together with the advanced application of combined finite/discrete-element modelling codes capable of simulating fracture behaviour, cave propagation and surface subsidence above block cave mines. The main objective of this work is to develop advanced numerical modelling methods to characterize complex rock mass behaviour above block cave mines. The research will also include the study of rock deformation mechanisms associated with the transition from surface to underground mining and the potential interaction between simultaneous open-pit and underground mining operations.

May 1, 2007

By Chris Larsen, Carole Fortin, Dave Scott, Curtis Deredin, Ian Orford, Jean Guy Gauthier, Andy Trusiak, Lyne Côté, Mike Cooper

"Upon successful commissioning of the Stage Grinding Project (Cormier et. al., 2002), process improvements predicted through pilot plant testing were obtained in several flotation circuits, resulting in higher grades and recoveries for zinc and lead concentrates. Subsequent to establishing new baseline operating conditions from the Stage Grind Project implementation, additional opportunities were identified, and through the application of Six Sigma methodologies further gains were made. Six Sigma improvement projects were carried out in the copper-lead, zinc, lead upgrading and bulk flotation circuits. The overall performance increase resulting from incremental improvement projects has been substantial.Most remarkably, given the operational maturity up to the late 1980’s, the Brunswick concentrator team has continued to deliver a steady stream of major improvements over the past fifteen years. While senior managers and their programs have changed several times, there have been some critical constants over the long run. Common elements have been a commitment to team work, a commitment to recruit and maintain technical personnel, a structured business improvement framework supported organizationally by senior management, and focus on a few priority initiatives rather than trying to fix everything at once.The paper briefly discusses the longer term setting and then endeavors to illustrate, with examples, how improvements are presently achieved by applying the Six Sigma quality program.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s larger lead/zinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 mine. In excess of 100 million tonnes have been milled to date. The concentrator employs differential flotation to produce lead, zinc, copper, and lead/zinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2005

By Timothy J. Myers

Expansion and the economic growth in the southwestern region of Missouri necessitated the expansion of State Route 249 and the construction of a new interchange to provide service to the Joplin, Missouri area. The project is located above a former lead and zinc mine in Jasper County, Missouri and includes a five bridge interchange connecting State Route 249 and US Route 171. The variable subsurface conditions, both natural and manmade, prompted the design team to use ground improvement via grouting and small diameter micropiles to provide support for several of the bridge foundations on the project. The scope of work included mine shaft closures, 56,000 ft of overburden and rock drilling, 11,139 ft of micropiles, 524 cy of balanced/stabilized high mobility grouts, and over 8,700 cy of low mobility grout. The selection of the grout used was based on the actual subsurface conditions. Low mobility grout (LMG) was used in voided conditions and for closure of the mine shafts encountered during the excavation. High mobility grout (HMG) was used in fractured rock with the goal of improving the mechanical properties of the rock underneath the future bridge footings and controlling grout volumes during micropile installation. The split spacing method was utilized for both LMG and HMG holes. Geology of the project site subsurface consisted of extremely variable bedrock with strong to very strong limestone, chert, breccia, extremely weak shale, and weak to strong sandstone. Previous activities associated with the mining disturbance (such as partial filled vertical mine shafts, shallow and deep mine horizons, modified hydrology including artesian conditions) further complicates the site subsurface conditions. Real time monitoring and recording of all drilling and grouting parameters was conducted to assist in the evaluation of in-situ geological properties of the site in order to modify the ground improvement and micropile program as necessary. This paper will discuss the design and execution of the ground improvement and micropile program. The project is an excellent example of the use of multiple ground improvement and foundation support techniques combined with real time data analysis to provide a foundation support solution for a complex geological environment.

Jan 1, 2009

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith's' concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman' who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009

By Albert H. Fay

The first data compiled by the Bureau of Mines relating to coal- mine accidents in the United States were published in Bulletin 69," in which the total fatalities by years and States were tabulated from 1896 to 1912. Since the publication of Bulletin 69, further research has been conducted, with the result that the bureau is now able to publish for the first time all of the fatal accidents described in the State inspectors' reports by States, causes, and calendar years, from the beginning of inspection service to date. For the anthracite mines of Pennsylvania, there is a continuous record since 1870; the records of the Pennsylvania bituminous mines are continuous from 1877, and, with the exception of one year, the Ohio records are complete from 1874 to date. In fact, the records of all of the States, with few exceptions, are complete; and incomplete data for any year may generally be attributed to the fact that no report was published during that year. The magnitude of the coal-mining industry in the United States is such that too much stress can not be placed on the need of safeguard- ing the three-quarters of a million men employed. Although the figures given herein show an appalling record for past years, they are not published for the purpose of proclaiming the high fatality rate of the past. They are a record of experience covering a period of 45 years, showing causes and results of many accidents in the coal mines of the United States. They represent a diagnosis of the hazard of the mining industry, pointing out the principal physical causes of accidents, and make available a body of uniform facts that will serve as a basis of preventive measures for use in future operations. It is with these great purposes in view that the Bureau of Mines presents the classified data in this report. Classification and study of mine accidents on the basis of number of persons killed is common and very old, but fails to throw enough light upon the problem involved. Many serious accidents in mines have no fatal results, hence in a tabulation of fatalities they are overlooked and the real hazard of the industry is not made clear. An accident does not necessarily include an injury that may result therefrom. Such accidents as the breaking of a hoisting cable, an explosion of powder, gas, or dust, a runaway car or motor are all serious. Although no loss of life results, they should be recorded, investigated, and studied to prevent their repetition. No accurate data for the United States are available showing how far the personal element as related to the miner and his co-worker, the mine foreman, or to the superintendent and others in authority, contributes to accidents. Many accidents are due to inexperience on the part of the miner, his failure to heed orders, a misunderstanding of instructions and last, but not least, carelessness of himself or his fellow worker. A foreman or superintendent may fail to give proper warning regarding the conditions of certain parts of the mine; he may not have inspected certain rooms or entries on the day of a mine accident; the mine may not be properly equipped, or the operator may neglect to comply with the inspector's recommendations. There is, therefore, a personal element on the part of both the operator and the miner that must be considered. Legislation and the enactment of compensation laws will make the operator realize the seriousness of the mine-accident situation, when fatalities and injuries are to be paid for in legal tender of the realm. The miner must be educated and made to realize the dangers he encounters; he must learn that self-preservation and the safety of his fellow workmen should receive his first attention; he should cooperate with his employer, his asso- ciates, and the State mine inspector to the end that the mine hazard may be reduced to a minimum. "Cooperation for safety" should be the watchwords of the operator, miner, State inspectors, and all others in any way interested in the mining industry.

Jan 1, 1916

By James J. Graham

Uravan, Ambrosia Lake, Gas Hills and South Texas are all historic names in US uranium. These mining areas supplied the uranium that brought the United States into the nuclear age during the 1960s, and fueled the birth of nuclear energy for peaceful uses — a promise of nearly limitless, clean energy for the world’s future. That promise still exists today, but it is hard to hear over the rhetoric of environmental activists and politicians. Nuclear power offers dependable electricity with limited environmental impact at stable prices. Nuclear power releases no greenhouse gases or particulate matter into the atmosphere. High level nuclear waste (HLW), although long lived, is readily controlled and compact. In the United States, generating 1 billion kWh of electricity with coal produces 47 kt (52,000 st) of solid waste (ash and sludge), compared to 3.6 t (4 st) of HLW produced by nuclear.

Jan 1, 2002

By T. Tholana

South Africa hosts some of the world?s largest known resources and reserves of minerals that are strategically important to the global economy. The country?s mining industry contributes significantly to the national economy in terms of gross domestic product, export earnings, corporate tax receipts, remuneration earnings, and employment. Platinum, gold, and coal are significant minerals because they make the largest individual contributions to these economic indicators. Several factors impact the cash cost performance of operations that mine these minerals, thus affecting the future sustainability of these operations, which are generally ?price-takers?. It is therefore important that the cash cost performance of operations for these key minerals is analysed. Commercially available industry cost curves can be used for such analysis. However, some companies may not be able to afford to purchase these curves. This paper presents a simple Microsoft Excel® algorithm for constructing the curves. It also demonstrates how the constructed industry curves were used to analyse the cash cost performance of South African mining operations for the three selected minerals for the period 2007 to 2011, which included the 2008 global financial crisis. The analysis revealed that the operations were affected by several global and local factors during the review period. The work reported in this paper is part of an MSc research study at the University of the Witwatersrand. Keywords cost curve algorithm, economies of scale, cash cost performance

Jun 1, 2013

By Michael S. Wieland

"Toxic fumes cause fatal andnonfatal incidents in underground mining, where the working environment tends to trap the fumes, hindering the restoration of non-harmful conditions. Workers can underestimate the residual fume toxicity and return to the work site too quickly. The toxic fumes from charge explosions depend upon a number things: formulation ingredients, mixture uniformity, water resistance, hole contaminates, rock hardness, and dust interactions. Transitory hole-to-hole waves can cause partial desensitization, ruin the reaction kinetics, and worsen the fume toxicity.Traditionally the toxic fume hazard for a candidate explosive is resolved from a requisite tally of fume components. The resolution starts with the fume spectrum, a tabulation of specie concentrations, transformed to standard reference conditions and readjusted to remove the air dilution. The resultant influence, which is referred to as relative fume toxicity RFT, is deduced by a formula rule with some chosen constants and the requisite concentrations. The RFT result is normally compared to an RFT criterion that represents the worst-case (maximum) tolerable fume toxicity, as stipulated by regulations or otherwise."

Jan 1, 1997

Les Mines Inmet ? La Division Troilus exploite une mine d?or à ciel ouvert depuis 1996 et produit un concentré de cuivre. La Division Troilus est localisée à 175 KM au nord de la ville de Chibougamau? au 51 parallèle.

Feb 1, 2008

By Frank E. Chase

Clay veins, also referred to as clay elastic dikes, have been responsible for numerous underground injuries and fatalities. These hazardous structures are also responsible for increased production costs during all phases of mining. For these reasons, the Bureau of Nines has investigated the physical characteristics of and roof instability problems associated with clay veins in order to make support and other mining recommendations. In addition the occurrence and origins of clay veins were examined to determine whether or not the structures could be projected into unmined portions of the coalbed. This investigation included portions of the Arkoma, Illinois, Northern Appalachian, Southern Appalachian, and Uarrior Coal Basins. Virtually a11 clay veins observed or documented occurred in the Illinois and Northern Appalachian Basins. Observed clay veins ranged in sire from 1 inch to 16 feet In cross-section and were found under shale, siltstone, sandstone, and limestone roof rock. Individual clay veins were predominantly composed of claystone; however, limestone. siltstone. and sandstone infilled clay veins do occur. Clay vein formation has been associated with the infilling of fissures which result from compressive, tensile, or shear ground failures. These gaping fissures were propagated by compactional processes and/or tectonic stresses active during and subsequent to coal iff cation. Associated fault, fracture, and slickenside planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance the roof is segmented into cantilever beams causing unstable conditions. Therefore, the strata on either side of the clay vein must be bolted and strapped together to form a beam.

Jan 1, 1984

By Robert E. Johnson

1962 was the second year of recovery from the mild 1960-61 recession. The year-to-year gain in constant dollar gross national product, our most comprehensive measure of the country's economic performance, was 6.0 percent (from $447.7 billion in 1961 to $474.8 billion in 1962). The unemployment rate declined from 6.7 percent to 5.6 percent. Although it was a good year, there were still unused resources of labor and capital which implied that the economy was operating below its potential. The year-to-year change in the Federal Reserve Board (FRB) index of industrial production of 7.6 percent masked the fact that more than one-third of the growth took place within 196L The monthly index rose only 4.8 percent during 1962, from 114.3 in January to 117.8 in September. The fact that the economy as shown by the industrial index, rose rapidly in the first half of the year only to remain on a plateau of 119-120 during the second half, led some people to fear an imminent downward turn. This did not occur. Neither production nor consumption of mineral fuels advanced as fast as the total economy. But consumption showed more gain than production, 5 percent compared with somewhat less than 4 percent. Production of both crude oil and natural gas reached new highs while bituminous coal production was the highest in 5 years.

Jan 1, 1963

By P. Miranda, K. Le, G. Maes, R. Peters

"The Mount Milligan Mine, owned by Thompson Creek Metals Company Inc. (TCM), started operations in September of 2013. It is located between the communities of Fort St. James and Mackenzie and is the first major metal mine to open in British Columbia in 15 years. Based on reserves as of January 1, 2014, it has an estimated 22 year mine life with 2.1 billion pounds of copper and 6 million ounces of gold in reserves. Like all commissioning operations, there have been issues achieving design throughput and recovery due to flow sheet design, equipment failures, control philosophy, and reagent scheme. Efforts to improve overall mill performance include equipment modifications, reagent screening and testing, and grind size testing. Applying these changes to the mill and working closely with the mine has resulted in continuous improvement each month as Mount Milligan looks to achieve the nominal design capacity of 60,000 dry metric tonnes per day in the later part of 2015. Considerable focus is being placed into ensuring size reduction equipment is utilized effectively. Additional modifications and tests are being undertaken to steadily improve processes and alleviate restrictions in the mill. This paper will discuss the start-up and present ramp-up history of Mount Milligan, the current mill processes, and the steps taken to achieve expected production numbers.OPERATION BACKGROUNDMount Milligan is an open-pit copper and gold operation wholly owned and operated by Thompson Creek Metals. It is located approximately 155km northwest of Prince George, British Columbia, between the communities of Mackenzie and Fort St. James. The copper-gold porphyry deposit contains a Measured and Indicated Mineral Resource of 706.7 Mt at 0.18% Cu and 0.33 g/t Au, containing 2.84 billion lb. copper and 7.50 million oz. gold. Mine life is currently estimated at 22.1 years (“Feasibility Update – Mt. Milligan,” 2009). The mill is designed to process 60,000 dry metric tonnes per day and produce 400 dry metric tonnes of concentrate per day averaging 25.5% Cu and 40 ppm Au. Concentrate is delivered by truck and trailer to Mackenzie followed by rail to Vancouver for overseas shipping to various customers.Mount Milligan is considered a “zero discharge” operation meaning no process or surface water will be discharged to the environment. As well, stockpiling is very limited and is only permitted for a short period of time. This scenario presents several unique challenges. Scheduling of ore/waste production must be carefully planned as waste rock is used to build the tailings storage facility (TSF). Reagent selection is also important as persistent chemicals will have a tendency to build up in reclaim water which feeds the process water tank."

Jan 1, 2015

By Luis E. Vallejo

The strength measured by the uniaxial compression test is a parameter that is widely used for the engineering classification of rocks. Sedimentary rocks such as shales, however, are difficult to evaluate by uniaxial compression tatting because the rocks slake during the preparation of the standard samples required for the tests. Indirect methods such as the point load test have been proposed to determine the unconfined compressive strength of shales and other soft rocks. It is current practice to use 24 as the conversion factor between the point load strength, Is, and the unconfined compressive strength, sf (sf = 24 Is). The present study investigated index-to-strength conversion factors for shales and sandstones obtained from surface coal mining sites in the Appalachian region. Regression analyses indicate that a conversion factor of 12.5 best correlated the strengths obtained from the point load and unconfined compression tarts in the case of shales. For the sandstones, a value of 17.4 best correlated the strengths.

Jan 1, 1989

By Hamid Maleki

In this paper, the authors present a review of data gathering programs and stress analyses for improving mine layout designs at BRL mines located near Paonia, Colorado. BRL and other companies have used both longwall and continuous miner methods for the extraction of the Upper D, Upper B, Lower B and C seams from the multiple-seam reserves in the North Fork Valley. Historic mining in the B and C seams has created stress footprints in the neighboring unmined seams compounded by stress transfer from recent longwall extraction in the Upper D Seam. Thus optimum positioning of workings in the remaining reserves requires careful collection of pertinent data and consideration of load transfer from previous workings through remnant abutment pillars. Based on long-term subsidence monitoring, underground mapping and stress analyses, we have confirmed initial load transfer analyses finding mild interactions between the UD and LB workings, and the mining conditions have proven to be good and manageable during the development stage of the LB Seam. This has been achieved through prudent mine planning, prudent positioning of the gateroads in multiple seam workings and support allocations.

Jan 1, 2007

By D. Lusinga

Hydrocyclones are a common feature in almost all mining operations in the world, serving mainly as classifiers. Some of their advantages include low capital costs, low space requirements and their ability to reduce residence time in closed circuit grinding processes. Although an extensive body of literature exists for hydrocyclones, these devices are still inherently inefficient, and more research is currently being undertaken, particularly in the field of modelling. In the vast body of hydrocyclone literature published so far, there has been little or no effort devoted to analysing the effect of the cone force ratio on the performance of hydrocyclones. The cone force ratio is defined as the ratio of the spigot to the vortex finder diameter (Shah, 2005). In this study a total of 44 tests was carried out in a custom-built rig at the University of Cape Town. These tests were aimed at evaluating the effect of the cone force ratio on the performance of as mall diameter hydrocyclone. The cut size and water split were used as the criterion for evaluating the performance of the hydrocyclone. Results from the tests showed that the cut size decreased with an increase in the cone force ratio. The cut size also appeared to decrease as the calculated locus of zero vertical velocity (LZVV) shifted inwards. The water recovery to the underflow appeared to increase with an increase in the cone force ratio. The effect on the cut size of adjusting the cone force ratio was found to be higher for a coarser feed than it was for a finer feed.

Jan 1, 2009

By M. Rafie, M. Rinne, F. Samimi Namin

"SynopsisRock mass classification systems constitute an integral part of empirical underground excavation design. One system that is commonly used to classify rock mass is the Rock Mass Rating, or RMR, system. The RMR system has evolved over time to better reflect the perceived influence of various rock mass factors on excavation stability. While the introduced modifications have enhanced the applicability of this classification system, there are still areas that cause potential ambiguity. The RMR system cannot deal with input data ambiguities, uncertainties, and vagueness. To deal with the uncertainty, a Fuzzy Rock Mass Rating (FRMR) has been developed. This study aims to describe the main concept of the fuzzy approach, which is implemented in the FRMR to classify rock mass. The FRMR considers the uncertainty associated with the input data (uncertain variables) used in rock mass classification. The Gol-e-Gohar (GEG) area 3 iron ore deposits in the south of Iran were chosen as the case study for investigating the applicability of FRMR. The results of this study show that the FRMR software tool can easily be used for rock mass classification, even if uncertain input parameters have been used. FRMR consists of three parts, each of which is suitable for certain conditions.IntroductionNowadays, rock engineering classification systems, which constitute the backbone of the empirical design approach, are widely employed in both civil engineering and mining engineering. Rock mass classifications have recently been quite popular and are being used mostly for the preliminary design and planning purposes of projects. According to Bieniawski (1989), a rock mass classification scheme is intended to classify the rock masses, provide a basis for estimating deformation and strength properties, supply quantitative data for support estimation, and present a platform for communication between the exploration, design, and construction groups."

Jan 1, 2015

By Y. Q. Zhang, S. S. Peng

Numerical modeling was used to design the pillars and bolting plan for a mine with weak roof and multi-seam stress condition. Previous mining experience, pillar/roof yielding and in-situ horizontal stress were considered in the models. By modeling the upper seam yielding and vertical stress transfer, a multi-seam influence zone was obtained. Appropriate pillar sizes were designed for conditions with and without upper seam stress influences. Roof support for the track and belt entries, using fully-grouted resin bolts and cable bolts, was proposed and implemented in the model. The bolting plan was evaluated under the weak roof condition.

Jan 1, 2004