Search Documents

By A M. Hagni

Certain copper ores from the Nchanga Copper Mine in the northern Zambia Copperbelt are refractory with respect to conventional beneficiation techniques. This paper reviews recent study of those ores to determine their mineralogy, textures and nature of copper occurrence. Two suites of refractory ores were selected for study: 1.  samples of stockpiled ores from an open pit, and 2.  drill core samples from copper ores. Both sample suites are from the upper orebody at Nchanga and contain about 0.3 - 1.4 per cent copper as determined by atomic absorption, but they represent separate stratigraphic, mineralogical and beneficiation problems. Ore microscopic examination showed that fine-grained copper sulfides are totally lacking from both suites of refractory ores. Petrographic study found malachite in the refractory ores from the open pit, but that malachite probably is post-mine. The opaque mineralogy of the open pit refractory ores is dominated by goethite that occurs mostly as pseudomorphic grains after pyritohedral pyrite crystals that average 200 - 250 ¦m across. Haematite occurs as bands within or as outer shells of the goethite grains. Additional goethite occurs locally as finer-grained areas of exotic goethite. The opaque minerals in the drill core refractory ores are dominated by euhedral ilmenite crystals about 50 - 175 ¦m long. Anatase is the dominant opaque mineral in some drill core samples where it is largely pseudomorphic after ilmenite crystals. Goethite accompanies malachite in unusual drill core refractory ores that have experienced intense hydrothermal alteration. Thus, ore microscopy and petrography showed that fine-grained chalcopyrite and bornite and pre-mine malachite were not the causes of the refractory nature of the ores studied. Electron microprobe revealed that most of the copper occurred in solid solution within micas. Application of automated SEM techniques has provided a detailed understanding of the distribution of copper in these refractory ores.

Jan 1, 2008

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

Change is inevitable but learning from change is an option. Willingness to learn is one of the first lessons that a leader must learn. Get comfortable and get left behind. I propose to outline the main social changes which are taking place and their impact on the Minerals Industry. Also the changing way we do business and what are the skills needed to manage that change and diversity. How are Associations and Institutes responding to this ever changing environment? More specifically, what is my Vision for the Institute to assist professionals to achieve greater and continuing professional excellence in their chosen professions?

Jan 1, 2000

By Patrick M. Y. Waye

As mines utilise more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with high speed data at 30 Mbps and the other for mine wide evacuation and safety applications. The high speed data system incorporates stateof- the-art data networking technologies and the existing leaky cable narrow band radio channels. The new system provides over the same basic infrastructure the high speed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow band radio channels. The second system is a system for mine wide evacuation with "through the earth" communication infrastructure. Emergency situation can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, regular reporting from miners working alone.

May 1, 2001

By R. C. Burtan

Long before recorded history, man began to dig into the earth's crust in a never ending search for useful materials. It is well known that more than half of the earth's crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica-containing material have a great many uses in modern society. This material, however, is potentially an extreme health hazard. Silicosis: Not a New Disease Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. He was obviously describing silicosis. It is also apparent from ancient writings that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. Silicosis was certainly described by Agricola in his De Re Metallica published in 1556. Here he described lung disease among hard-rock miners. The original document was written in Latin and then translated in 1912 by Hoover and Hoover. One of these translators was Herbert L. Hoover, a former US president who once made his living as a mining engineer. More recently, there are numerous references in medical literature in the 19th and 20th centuries relating silica exposure to silicosis. There are specific references to mining in hard rock, as well as to sandblasting and a host of other industrial exposures. In 1919, Winslow described standards for measuring the efficiency of exhaust systems in polishing shops using sandblasting. These standards were equally applicable in the mining industry. As early as 1920, Winslow explored the efficiency of certain devices used to protect sand-blasters against the dust hazard. These devices were equally applicable in the hard-rock mining industry. The medical community recognized the silica health hazard in the early 1900s. Middleton described the illness in the British Medical Journal in 1929. He noted the danger to health at that time. D. Hunter mentions in his book, The Diseases of Occupations (1969), the monumental work of Merryweather in 1936, in which he surveyed the silicosis risk in Great Britain. He showed statistically that the average employment length of sandblasters who ultimately died of silicosis was 10.3 years, compared to 40.1 years for all fatal cases, irrespective of occupation. Sandblasting and hard-rock mining and drilling, obviously, are very hazardous occupations. Weil and Zisking of Tulane University wrote in 1975 that "it was known as early as 1935 that the course of silicosis is much more rapid in sandblasters than in miners or foundry workers. This can be explained by the fact that sandblasters are exposed to an almost pure siliceous dust containing high concentrations of respirable particles within the range of 1 to 3 micron size." Protecting the Worker The medical community recognized in the early 1900s the need for proper protective equipment for all of those who worked with siliceous materials. Middleton, writing in 1929, said: "The worker is then protected by a close fitting helmet with an air feed, much as in the case of an underwater diver. In spite of these precautions, cases of silicosis among sandblasters are being met with today. It is a matter for serious consideration whether a substitute, such as steel or iron grit, could not be used to replace the siliceous grit as the abrading material." C. E. A. Winslow, a professor of public health at Yale School of Medicine, and others wrote of the need to protect sandblasters by

Jan 7, 1984

By John Kinneen, Sunghoon Choi, Arne Fareth, Edward S. Barboe, Kyle R. Ott

A new water treatment plant is to be constructed for a portion of the water supply system of New York City. The project includes construction of new water conveyance tunnels crossing perpendicular and sub-parallel to the existing pressurized water tunnel at two locations. A study was conducted to evaluate the impact of new tunnel construction on stability of the existing tunnel and hydrojacking potential in the surrounding rock mass. This paper introduces a practical approach to evaluate tunnel interaction, expressed in terms of rock-liner interaction, stress-induced stability and hydrojacking failures. A simple method to evaluate hydraulic and mechanical properties of concrete liners and jointed rock mass is also presented.

Jan 1, 2007

By Michel Robert

"In 1974, Copperfields Mining Corporation and Soquem formed a new company, Niobec Inc, to bring the niobium deposit of the St-Honore carbonatite into production.St-Honore is located in the Saguenay area, near the cities of Chicoutimi and Arvida, and about one hundred and forty (140) miles north of Quebec. The discovery of the carbonatite complex was made in the fall of 1967 as a result of an airborne radiometric survey in search of uranium. The detailed exploration of the carbonatite indicated two niobium-bearing formations besides the original discovery of a rare earths zone. During the following years, the niobium formations were defined by diamond drilling and a decline was driven down to obtain adequate samples for metallurgical evaluation. In 1974, after seven hundred (700) bench scale tests, eleven (11) months of pilot plant 2nd a worldwide market research, a joint decision was made to initiate the development of a fifteen hundred (1500) T.P.D. mine and mill, under the management of Teck Corporation. The construction of the facilities were completed in early 1976 both on time and within budget. Niobec is now the only north american and the world second largest producer of Niobium concentrate.The process used at Niobec was developed from the pilot plant programs and later modified by the mill personnel. A simplified flowsheet for this process is shown on the slide. Briefly, run of mine ore is crushed to minus 5/8"" and fed to a rod mill, ball mill, and screens circuit where the ore is ground to 92% passing 65 mesh. The ore is deslimed in two stages of cycloning, and the final cyclone overflow at 85% minus 11 microns goes to waste. The cyclone underflow is conditioned prior to flotation of a carbonate-apatite concentrate. This concentrate is cleaned twice and then pumped to tails. The carbonate rougher and cleaner tails are cycloned in two stages to change the process; water and then sent to the pyrochlore rougher flotation. The rougher concentrate is cleaned five times. This is followed by pyrite flotation to remove sulfur, leaching with hydrochloric acid to remove phosphorus and dyed to less than 0.1% moisture before being sent to packaging."

Jan 1, 1978

By D. Harrington

Hatch (260) made the following pertinent statement regarding the present status of engineering design of dust-control equipment: Textbooks on ventilation and engineering handbooks devote little or no space to methods of control of industrial dust, and in the technical journals papers on fundamental engineering design of equipment are conspicuous by their absence. In a recent bibliography of the literature on pneumoconiosis less than 1 percent of the articles dealt with the engineering control of the disease. The science of dust control has not developed beyond the stage of trial and error, and the design of structures for the suppression of dust is based almost entirely upon empirical data together with one or two elementary formulas. The latter were derived from the generalized experience in a limited number of Industries such as woodworking, where conditions and requirements are not at all like those, for example, in a sand-pulverizing plant. Wide experience and good judgment are essential to the proper use of the scanty information that has been collected and systematized. Without attempting to minimize the importance of experience in engineering design, it is necessary to point out that most of the past experience obtained in the empirical design of dust-control equipment was not evaluated by means of quantitative studies of the actual reduction in dust , fence, past experience does not necessarily furnish the proper guide for future design. In fact, recent surveys in certain industries, employing modern methods of investigation, have shown that existing equipment is in many cases inadequate.

Jan 1, 1935

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertained by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By F. D. Wright, H. D. Fara

The solution to the plastic and elastic stresses around a circular shaft in a hydrostatic stress field that has appeared in two editions of a widely used book on rock mechanics1 is in error. Although this is a relatively minor matter, the correct solution was not found by a literature survey, so it appears worthwhile to present it. For a homogeneous, isotropic, rigid plastic-elastic body in plane strain which obeys Tresca's yield criterion the following equations must be satisfied:'," In the plastic zone,

Jan 1, 1963

Volume 2 presents the results of studies of Phelps Dodge Corporation's tailings embankments numbers 1West and 2 West, at Morenci, Ariz. The work involved compilation and description of pertinent factors relating to the physical features and operational characteristics of the facility, including information on embankment construction practices; investigation and research of the general geologic and seismicity characteristics of the site and vicinity; limited field exploration and materials sampling and testing at the site; installation and limited monitoring of piezometers, surface movement markers, and slope indicator casing; limited laboratory testing of materials to evaluate the basic index and engineering properties of the embankment and tailings materials; selected engineering analyses of the embankment for various types of potential "failure" conditions; and includes appendices.

Jan 1, 1974

By R. E. Chaney

This report summarizes the research on the Strategic and Critical Materials Program tasks conducted at the Idaho National Engineering Laboratory (INEL) between May 1984 and April 1985. The work is divided into two areas: 1. Production Technologies - Tasks directed at developing advanced extraction technologies ? Biologically-Assisted Minerals Processing ? Metal/Gas Reactions and Thermal Plasmas ? Dehydration of Aluminum Chloride Hexahydrate (completed). 2. Conservation/Substitution Technologies - Tasks directed toward establishing the technical processing base which will permit the use of advanced materials ? Joining of Rapidly Solidified Alloys (RSA) ? Joining of Silicon Nitride-Based Ceramics ? Nondestructive Evaluation of Ceramic and RSA Joints and Materials ? Substitute Catalytic Materials for Platinum.

Jan 1, 1985

By T. A. Lang

Concepts and equations have been developed to quantitatively determine the stability of a rock bolted coal mine roof as a structural (beam-arch) member consisting of reinforced rock units. The equations take into account: rock bolt tension, length, spacing, and orientation; size of opening, strength and physical properties of the rock; and loads from distressed rock, and were critically reviewed using sensitivity analyses and the results available from relevant previous analytical and physical model investigations. It is concluded that they can essentially be validated by using small scale physical models and the full size mine entry model at the USBM Spokane Research Center. However, a comprehensive research program, including analytical and laboratory investigations and field trials in typical mines, will be required to define and validate criteria and standards for using the equations as a basis for a rational design code for rock reinforcement installations to replace the semi-empirical rules now being used. For example, these studies have shown that the practice of installing vertical roof bolts with a uniform spacing equal to the bolt length is inherently unsafe and that the spacing should be reduced near the walls to prevent shear failure of the roof strata. The development of such a rational design code would provide enhanced safety in coal mining operations and warrants a high priority in the Bureau's ground control research program.

Jan 1, 1981

By R. Farrar

The survey work on protective canopy design was conducted in a 2-month period commencing November 15, 1973. The reported re¬sults under this contract are intended to provide guidance to coal mine operators in complying with federal regulations pertaining to incorporation of protective canopies on underground coal mine electric face equipment. All coal mine electric face equipment manufacturers and 11 coal mines were visited in the course of conducting this survey. Canopy designs currently being manufactured and those now being used underground were examined and discussed with manufacturers, mine operators, machine operators, and safety committeemen. The general objective was to find out what kind of canopies are now being made and used underground, what the operational problems are, and what can be done to secure improvements. Specifically, the survey scope was as follows: a. Survey all electric face equipment manufacturers. b. Survey 10 coal mines (seam height 60 inches and greater). c. Identify current production canopy configurations and minimum mine entry dimensions for each model and type of electric face equipment. d. Assess in-mine operation of canopies developed by manufacturers and/or coal companies. e. Specify optimal canopy configuration and minimum mine entry dimensions for each type and model of electric face equipment.

Jan 1, 1974

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertainedd by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By D. Harrington

This circular presents part I of a review of the literature on effects of breathing dusts, with special reference to silicosis, largely in the minim; and allied industries. The literature on this subject is so extensive that no attempt has been made to include all published material but only to assemble some of the more outstanding data on several aspects of the subject. Parts II and III will deal with prevention and treatment of dust diseases and some of the economic and legal aspects of dust diseases in industry, with special reference to mining. Dust diseases arc much before the public at present, and there is good reason to believe that the information on the subject available to the layman is extremely meager; even those rated as experts usually have a more or less theoretical conception of the diseases, their causation, remedies, and prevention, rather than actual experience with them. Until recently little attention has been given to prevention, and the usual attitude of the engineer, upon whom the main reliance for prevention ultimately must devolve, has been to let "sleeping dogs lie" or, more definitely, to "let well enough alone." However, the "laissez faire" attitude no longer is tenable, and in the past few years numerous conditions have caused those engaged in industry, including mining, to bring the subject before the public with a view to ascertaining the facts upon which to formulate remedial measures, primarily preventive.

Jan 1, 1935

By Mary L. Pearson

Ibis report summarizes the results of the contract. Included are summaries of existing legislation pertaining to outcrop barriers and a state-of-the-art survey of outcrop barrier designs and related, mine closure techniques. Six sites were inspected in the field and are presented as case histories The data analysis presented includes a computer modeled seepage analysis, an overburden blew-out analysis, and a wedge stability analysis. The results tit these analyses are interpreted to form recommendations for coal outcrop barriers which will minimize seepage and the potential for failure. Supplementary support and reinforcement alternatives are also discussed.

Jan 1, 1981

The ability to track miners and communicate with them while they work in underground coal mines is important during normal daily operation, and critical in emergency conditions. This was evident during recent incidents at underground coal mines worldwide. Communication with miners and the knowledge of their location is of great importance for rescue efforts and the preservation of life. Numerous technologies have been developed, adapted and deployed to meet tracking requirements of the Mine Improvement and New Emergency Response (MINER) Act of 2006. Evaluating the performance of these systems has proven to be dif?cult for mine operators, system manufacturers and regulatory agencies. The MINER Act requires operators to improve accident preparedness by developing an emergency response plan speci?c to each mine. With the recent implementation of the provisions of the MINER Act of 2006, all underground coal mines in the United States are subject to the mandates of legislation concerning communication and tracking system installation. As of June 2011, 203 new or revised tracking and/or communication systems had been approved by the U.S. Mine Safety and Health Administration (MSHA), with nearly 50 other systems or revisions in the approval process (MSHA, 2011). At that time, the available approved systems for underground coal mine use included these types: ? Leaky feeder communication systems. ? Fixed node-based communications and/or tracking systems. ? Wireless node-based communications and/or tracking systems. ? Medium frequency (MF) communication systems. ? Communication system peripherals. Other types of tracking systems have since been developed and some manufacturers are seeking approval for use in this application. Some of the new products include through-the-earth (TTE) systems and various radio frequency (RF) adaptations. New technologies that are currently being developed and deployed in other industrial applications should also be considered, including acoustical, optical, inertial and hybrid technologies. To date, no uniform method has been employed in the industry to effectively compare and evaluate the performance of installed systems. Neither industry operators nor regulatory agencies can accurately assess the capabilities of installed systems in the continuously changing mine environment. There is a need for a uniform evaluation method that provides the ability to assess how different systems and technologies perform in various mining applications, and whether they can satisfy the regulatory requirements.

The Bibliographic Data Base contained in the present volume is the result of a literature search conducted as one task of the Bureau of Mines project concerned with research in borehole assay technology. The data base includes articles, symposia, books, corporate and government reports, patents, and other literature concerned with some aspect of borehole logging, from January 1969 through December 1975. Occasional updating to keep the data base current is anticipated. The remainder of the intro¬duction will be devoted to the explanation of the organization of each entry, along with the translation of terms and abbreviations used in the text. Each entry contains six sections. These include an ID code, a title, an author section, a source section, an abstract, and a descriptor section. The first item listed in an entry is the ID code. This serves to identify an entry. It consists of the first six characters of the first author's (or editor if no authors are involved) last name, along with the last two digits of the year of publication. A letter sometimes follows the year of publication to assure a unique alphanumeric code. For example, if an author named Wilson writes more than one piece of literature in a given year (for example, 1972), the ID code for the entries identifying these pieces of literature would be identical. Therefore, to allow for unique ID codes, the first piece would he identified as "WILSON 72,', the second piece as "WILSON 72A", the third "WILSON 72B", and so on.

Jan 1, 1976

To improve communication among Government, industry, and academic researchers in the field of thermodynamics, the Federal Bureau of Mines sponsored a Workshop on Techniques for Measurement of Thermodynamic Properties in August 1979. Participants at the workshop presented 33 papers on the subjects of temperature measurement and control, general calorimetric techniques, low-temperature calorimetry, high-temperature calorimetry, galvanic cells, ionic solutions, and heterogeneous phase equilibria. A special invited lecture was presented by E. F. Westrum, Jr., on the resolution of lattice heat capacity. This Information Circular comprises the proceedings of the workshop and includes the texts of papers presented and discussion by attendees.

Jan 1, 1981