Search Documents

By K Firmin

The Mt Tom Price orebody of Hamersley Iron Pty Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the ore body, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control of products based on selective mining is the production of advance data on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades are determined from assay of samples taken from blast hole cuttings. As shales are more friable than hematite, product fines are always lower in iron grade than the lump product. The realisation of contract specification grade is more difficult with fines than with lump, so maintaining the correct fines grade becomes a prime factor in quality control. Control of fines grade is presently effected by aiming for an appropriate feed grade to the primary stockpile. Studies to estimate fines grade directly by qualitatively taking into account material types are in progress. Quality control measures are checked by monitoring the crushing and screening plant output, and taking appropriate compensatory actions in the mine when required. Minor fluctuations in quality of fines can be blended out on stockpiles. The quality control measures described ensure constant quality products, and a good recovery of high grade material from the deposit.

Jan 1, 1971

By A. F. S. Schoukens

The Mintek Thermal Magnesium Process (MTMP) was successfully demonstrated in November 2004. The pilot plant was operated continuously for 8 days, during which about 30 tons of magnesium producing recipe was smelted in a DC (direct-current) arc furnace at a feed rate of 525 kg/h. The furnace was operated at power levels of 700 to 850 kW, resulting in slag tapping temperatures of 1600 to 1700°C. Magnesium extraction averaged 77 per cent and was as high as 85 per cent during good extraction periods. The furnace generated 70 to 85 kg/h magnesium vapour that was delivered to the condenser where the temperature was controlled at 680 to 720°C. The novel condenser captured the magnesium in a liquid state, which was tapped periodically as required. In total, 15 magnesium-tapping operations were carried out, proving that online magnesium tapping can be consistently performed without any major difficulty. About 3500 kg of crude magnesium was produced with a quality that was similar to, if not better than, that of the Magnetherm?s crude metal. The condensation efficiency averaged 85 per cent, and peaked at 87 per cent, which exceeded the target of 80 per cent set for the pilot scale. A brief magnesium market study was also carried out. Magnesium demand is expected to keep on growing by 6 to 8 percent over the next 10 years and could reach 2 million tons by the year 2020. The growth will be mainly in the die-casting sector for light-weight automotive applications. China is likely to remain the dominant supplier of primary magnesium but competitively priced non-Chinese magnesium producers will be needed to sustain the anticipated growth of 6 to 8 per cent over the next 10 years. In addition, a prefeasibility study was undertaken for a commercial plant. The study confirmed the relatively low capitalcosts of the MTMP process, as well as the competitiveness of theoperating costs, as compared to the industrial electrolytic process.

Jan 1, 2006

By L. H. Simons, H. H. Spain

I NT RODUCTION Theory indicates that linear water-floods should exhibit scaling and stabilization properties in both oil-wet and water-wet porous media'. Experimental verification of these proper-ties in oil-wet media was obtained some time ago', and more recently, Perkins', employing a high permeability unconsoli dated sand and a low oil-to-water viscosity ratio, has obtained flooding data in a water-wet medium which follow the pattern of scaling and stabilization. Also, Root and Calhoun3 have found similar trends in the displacement of gas by liquids from unconsolidated sands. In general, however, the experimen-tal evidence appears still somewhat conflicting since scaling and stabilization of water floods in water-wet media has not been observed in most of the studies to date'.".'. The purpose of this paper is to provide a more comprehensive picture of waterflood behavior in water-wet media and to corroborate the validity of the scaling and stabiliza-tion concepts. The need for differentiating between the intrinsic nature of water-oil displacements inside a porous medium and perturbating secondary end effects is discussed, pertinent experimental procedures are outlined and the results of flooding tests conducted at low and at high oil-to-water viscosity ratios on con- solidated, water-wet Alundum cores are analyzed. END EFFECTS IN WATER-WET MEDIA Outlet End Effects The peculiar feature of the outlet end effect in water-wet cores is that it not only results in an excessive wetting phase saturation at the outflow face,'.' but that it also retards the moment of water breakthrough: i.e., causes an undue delay in the appearance of water in the produced effluent. Conditions existing in a water-wet core when water first arrives at the outflow face are schematically shown in Fig. 1. At this flooding stage the saturation distribution, Fig. la, has not yet been distorted by the outlet end effect. A water-invaded pore at the outlet core face, opening into the oil-filled void space between the end of the core and the end plate of the flooding cell, is illustrated in Fig. lb. The curvature of the water-oil interface is concave toward the outlet, and the pressure on the water side of the interface is lower than on the oil side by an amount equal to a certain capillary pressure (Fig. lc). Before the water (of this particular pore) can be produced from the core, it is apparent that the pressure in the water phase must exceed that in the oil outside the core. Accordingly. when water first reaches the outlet face, it will not leave the core but will accumulate inside, and only oil will be produced. Eventually, as the water injection is continued. sufficient pressure is built up in the water to reverse the curvature of the interfaces in the outlet pores, and only then will water be produced from the core. This stage, illustrated in Fig. 2. corresponds to the conventional "water breakthrough" observed in flooding experiments. For purposes of discussion, it is convenient to distinguish between the flooding stage at which water first arrives at the outlet face of a core (Fig. 1) and the stage at which water is first produced from the core ( Fig. 2). The former will be referred to as "water arrival" and the latter water breakthrough. In oil-wet media

By C. Taschereau, G. A. Vickell, A. R. Laplante

Evidence in support of an iron-gold corrosion cell during the high-temperature/highpressure elution of loaded carbon is presented herein including, but not limited to, its discovery, mode of genesis, and confirmatory laboratory testwork. A discussion of metallurgical and economic impacts, remedial investigations, plant design considerations, and future work including mitigative possibilities is presented.

Jan 1, 2006

Slime Flotation Using Ethoxylated Surfactants in Solutions of the Electrolytes

Sep 13, 2010

By S A. Myers, T Klein

The Yanacocha mining district is located in the northern Andes of Peru. The project is within the Cajamarca province, 20 km north of the town of Cajamarca and 600 km north of Lima, the capital of Peru (Figure 1). The district encompasses an area of 120 km 2 and is centred on the 78030'west longitude and 7000' south latitude. The project lies at an elevation of 3400 to 4200 masl.

Jan 1, 1999

By G B. Arehart, J L. Mauk

Quartz veins from the Martha Hill epithermal gold-silver deposit, Waihi, commonly exhibit crustiform banded textures. Visual differences observed between bands are primarily the result of a 1 to 1500 ¦m variation in quartz grain size. Quartz band textures are dominated by anhedral interlocking quartz mosaics, commonly associated with minor adularia and sulphide phases; these textures are interpreted to be products of amorphous silica crystallisation. The occurrence of rhombic adularia suggests that prolonged boiling influenced parent fluids. In contrast, the presence of coarsely crystalline bands, made up of subhedral to euhedral quartz grains, infers primary crystal growth from solution; evidenced by the occurrence of growth-zoned quartz within these bands. There is a narrow range of 3.3ë in d18Oquartz between maximum and minimum isotopic values for the deposit. Significant overlap in d18Oquartz values are observed between the Martha and Welcome lodes. However, statistically significant and commonly systematic differences do occur between individual bands analysed in most samples. Temperature fluctuations may be the dominant factor responsible for observed inter-band variation.

Jan 1, 1995

By D. Kidby, A. Briggs

"Vitrokele ™ is a synthetic adsorbent, using chelating groups on large polystyrene beads, developed in Canada over 7 years ago, and first commercialised in 1985 to recover noxious metals from plating wastes.Pilot plant trials have been performed in Australia and Canada to demonstrate the recovery of cyanide and removal of metal cyanide complexes from gold plant effluent using Vitrokele1 M 912. The pilot plants comprise a simple adsorption train (similar to a CIP circuit) followed by complete elution facilities, so that loaded Vitrokele™ can be stripped and returned to the adsorption circuit.An account of these campaigns is provided, showing the reduction of total CN levels from over 200 ppm to less than 0.5 ppm and Cu levels from approximately 100 ppm to less than 0.3 ppm in treated tailings.Comparisons between pilot plant results and laboratory test data are given and probable future work on the process and its application to the gold mining industry is discussed.INTRODUCTIONThrough millions of years of evolution, life forms have developed specialised molecules with exceptionally high affinity and selectivity for various metals such as iron, cobalt, zinc and copper.In the early 80's professors at the Faculty of Medicine of McGill University engaged in research on the extremely efficient ways that living cells captured trace metals essential for life.As research progressed, it became evident that the special molecules used by biological systems to capture metals could be synthesized to capture selected metals with similar efficiency from water or other solutions.The technology was first commercialised in 1985 to recover noxious metals from plating wastes with compositions applying the special molecules (chelating groups) on vitreous particles (hence Vitrokele™). To date approximately three commercial Vitrokele™ plants have been installed for treating plating waters in Ontario and Quebec."

Jan 1, 1992

By Gualberto Salas

Dado que la voladura es una de las operaciones unitarias de mayor extracción del mineral -en tanto logra una adecuada fragmentación de la roca con un costo reducido, es necesario lograr una interrelación entre los resultados de la voladura y el de las operaciones unitarias como herramientas que evalúan y optimizan los diseños de los disparos. En ese sentido, el presente trabajo describe las técnicas para el diseño de las mallas de perforación, los programas para la simulación de la voladura y también para medir los resultados, que permitirán realizar los ajustes necesarios para mejorar los resultados de fragmentación y reducir el costo de operación de minado.

Sep 13, 2001

The paper provides a brief review of a multivariate uniform conditioning and a localized multivariate uniform conditioning (LMUC) technique, and presents a production reconciliation case study based on a porphyry copper-gold deposit in Peru. The reconciliation study compares the longterm LMUC mineral resources model (typical of new mining projects, which are invariably based on drilling data on a relatively large grid) to the corresponding production blast-hole grade control model, as well as the final plant production.

Jan 1, 2014

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By M. S. P. Rampedi

The paper reports on a vacation work project conducted at Khuseleka No. 1 Shaft, Anglo Platinum, where there was a need to optimize the transport of personnel to level 15 and below. Approximately 900 men per hour need to travel between the shaft and the start of the current chairlift system. Time studies were used as the major indicator of the extent of the current problem, and it is recommended that a new chairlift system be installed to cover the distance from the vertical shaft station at level 15 to the chairlift decline station on level 15. A capital cost of approximately R10 million is necessary to carry out the proposed recommendation. Khuseleka No. 1 Shaft has the capacity to wind 1070 people per hour, and the current labour complement going to the level 15 shaft station stands at 1570 employees; thus at optimum efficiency the proposed chairlift system could transport the entire shift to the start of the current chairlift system in only 1 hour and 45 minutes. Reducing the distance walked at the start of the shift may also have an impact on productivity.

Jan 1, 2012

By Lutz Markworth, Fernando Parra, Wolfram Jaspers

"The worldwide demand of iron ore and the depletion of the high-purity deposits make it necessary to recover ores in increasingly fine size fractions or low Fe content in the feed material. Impurities for Iron ore processing plants are mainly Silica, Al2O3 and Sulfides.There is a copper processing plant in Chile, which has a high content of Fe in its tailings. These tailings will be re-processed to recover the Fe and to produce a pellet feed concentrate. This challenging flotation process was developed by the customer in his own laboratory. Different flotation technologies were tested. The best results were achieved with the PNEUFLOT® (PNEUmatic FLOTation). For a feed capacity of approximately 600 t/h, a flow sheet of two flotation lines with a reverse two-stage Amine-Silica flotation followed by a single stage reverse Xanthate Pyrite flotation was developed.Because of the two impurities the process control is very critical. Not even the reagent dosing has to be flexible for changes in the feed material; also the flotation cell has to be adaptable. Continuous development of the PNEUFLOT® cell with their specific advantages and the elimination of dysfunctions in the PNEUFLOT® cell have led to a growing demand of this type of equipment worldwide for the iron ore industry within the past years.INTRODUCTIONThe worldwide increasing demand of iron ore is mainly caused by China. This has a major impact on all economics worldwide as the metal price indicates. However, not even the iron ore and steel price, but all other commodities prices and the precious metals prices are increasing by a high percentage. Figure 1 shows the iron ore (pellets) price increase for Fe and the import of iron ore by China. Figure 2 shows the imports of iron ore to China."

Jan 1, 2008

By E A. Amaral Jr, A C. Chieregati, J C. O Souza

Cross-belt samplers are designed to sample particulate material in processing plants, usually when there is no space to install a conventional linear falling stream sampler. Most of the available cross-belt samplers are mounted on the top of conveyor belts, and remove each increment from a loaded moving conveyor with a 360° rotation of an open faced cutter, in a plane perpendicular to the material flow. Despite the practicality of this equipment and the fact that it occupies very little space in the plant, cross-belt samplers are well known for collecting biased samples, especially due to the increment extraction error. Sampling consultants around the world tend to condemn this sampling equipment, claiming that it is incapable of collecting the fine material from the bottom part of the load, and, since the sampling probability is not uniform for all fragments and depends on its position in the stream, this kind of sampler generates biased samples and its use should be avoided. Furthermore, the greater the segregation effect between particles, the larger the bias. However, some plants, whose initial design did not plan for the installation of a falling stream sampler, must rely on cross-belt samples for process control and reconciliation. For the past years, sampling equipment manufacturers have been putting effort in modifying the cross-belt sampler design in order to comply with the principles of correct sampling. Changes to the cutter material, shape, position, speed and movement in relation to the material flow have been made, and are continually being tested for different types of ore with various chemical and physical characteristics. This paper presents the improvements made to a cross-belt sampler at a gold plant feed in Brazil and describes the tests performed until it was possible to validate the new sampling equipment for reconciliation purposes.CITATION:Chieregati, A C, Amaral Jr, E A and Souza, J C O, 2017. Validation of a modified cross-belt sampler for reconciliation purposes, in Proceedings Eighth World Conference on Sampling and Blending , pp 247–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Newmont Gold's methods for deposit modeling vary, depending on geology, mining and processing methods, economic feasibility and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques and being flexible in selecting the appropriate methods. Newmont is one of the world's largest gold mining companies, with operations in the United States, Peru, Mexico, Indonesia and Uzbekistan. And it is active in exploration worldwide. At the end of 1996, Newmont declared a total reserve of 1.15 equity kt (37.1 million equity oz) of gold and 2.17 equity Mt (2.39 million st) of copper. The gold deposits managed by Newmont totaled 752 Mt (829 million st) of ore containing 1.28 kt (41.3 million oz) of gold averaging 1.71 g/t (0.05 oz/st). In addition, Newmont is developing a porphyry copper-gold deposit that totals 9.1 Gt (1 billion st) of ore containing 380 t (12.1 million oz) of gold and 4.82 Mt (5.32 million st) of copper. (In May 1997, Newmont Gold Co. merged with Santa Fe Pacific Gold Corp., thus increasing Newmont's reserves to 1.72 kt or 55.2 million oz of gold and 2.17 Mt or 2.39 million st of copper.)

Jan 1, 1998

Geostatistical methods have become well established in the last two decades for the evaluation of ore reserves in base metal, industrial minerals, coal and gold deposits of the Witwatersrand type. However, there has been considerable debate about the applicability of geostatistical techniques when applied to vein-type gold deposits with hydro or epithermal mineralisation. The main problems stem from a lack of spatial continuity and the highly erratic sample values that characterise these deposits. This paper reviews some of the current geostatistical techniques that are applied to the evaluation of gold prospects.

Jan 1, 1992

By F. J. Chernosky

Most previous studies of coal flotation utilized chemically pure reagents. Since such reagents are not available in quantity, a study of various wmmercially available reagents as frothers was undertaken. Flotation procedures similar to those used in a large number of commercial coal flotation plants were employed. The reagents used were compared on yield-selectivity-wst basis. The selectivity was found to be relatively constant with yields above 70% but the reagent cost varied greatly. The types of reagents available were compared. In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these have been an attempt to correlate the intrinsic chemical and physical proper- ties of the reagents or reagent groups to the floata-bility of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, 1) the yields obtained, 2) the ash levels obtained and 3) the reagent cost relating to these results. REAGENTS The reagents employed have been grouped into the following chemical classes: 1) aliphatic alcohols, 2) terpines, 3) glycols (synthetic water-soluble

Jan 1, 1963

By Éric Létoumeau, Julie Fournier, Sylvain Caron, Yves Breau, Martin Plante, Dominique Girard, Luc Tardif, François Robichaud

"Since 1999, COREM (formerly the Centre de Recherche Minérale) has conducted and coordinated research and development activities for a consortium of mining companies that uses the benefits and advantages of collaborative pre-competitive research. In particular, COREM’s “In Situ Optimization Group” is involved in the development and implementation of modem information technologies related to process optimization and control.The POP Project was launched in order to increase and consolidate the use of such technologies applied to mineralurgical and metallurgical processes. To ensure a successful transfer to the industry, there are a number of essential activities that have to be undertaken. These activities have been identified by COREM’s members and are grouped into three main modules:- R&D Module: research and development in universities and research centres;-Technology Transfer Module: integration of new tools into the POP Software, industrial applications and technical support;- Training Module: education of new engineers in universities and continuing education of plant personnel through on-site workshops.This paper outlines the opportunities that led to the definition of the POP Project, presents its main objectives and describes its main modules. The main features of the POP Software are outlined, the first applications at COREM’s member plants are presented and, finally, future developments are discussed."

Jan 1, 2002

By S. J. Schatzel

Coal mine longwall face ventilation is an important component of the overall mine ventilation system. Increases in the production rate due to higher capacity mining equipment tend to increase methane emission rates from the coal face, which must be diluted by the face ventilation with a minimal opportunity for assistance from additional control equipment (i.e., surface boreholes). Increases in panel length, in some mines approaching 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. Face ventilation can also be affected by communication with the methane-laden gob gas reservoir. Except in a two-entry system, belt air cannot be used to ventilate the face in the US, except in limited cases. This relatively recent requirement has further challenged the mining industry in maintaining adequate longwall face ventilation. To assess the effectiveness of current face ventilation practices, a face monitoring study was combined with a tracer gas test on a longwall face. The study was conducted at a US mine operating in a thick, bituminous coal seam with some self-heating tendencies. Multiple gob gas ventholes were located near the face and produced a small portion of ventilation air in their production flow. Initial results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Increases in methane concentrations in the tailgate entry in the vicinity of the longwall face T-junction appeared to be produced primarily by gas flow from the gob, not from increased emissions from the face. Barometric pressure variations were substantial over the course of the study and varied on a diurnal basis, as is typical of many mining operations. Suggestions are forwarded for reducing longwall face methane concentrations.

Jan 1, 2012

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100 per cent recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after 12 years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980