Search Documents

By Edwin W. Meyer

The augered cast-in-place piling technique was used to install deep foundations 20 feet into weathered sandstone. The project involved the upgrading of the Air Quality Control System (AQCS) for a 560 megawatt coal fired power plant located in Stillwater, Minnesota. The site subsurface consisted of 20 feet of overburden overlying weak sandstone. The overburden consisted of sands and gravels with cobbles and boulders, and variable thicknesses of peat. Ground-water at the site was approximately 8 feet deep. Two foot diameter piers were selected to facilitate installation through the cobbles and boulders in the over-burden and to penetrate the sandstone 22 feet. During installation of the first pier, the weak sandstone broke down to sand-sized material that could not be cleaned from the pier hole without the use of slurry to hold the material in suspension. However, the use of slurry would significantly impact both schedule and cost. Since the sandstone could be easily drilled with the pier equipment, it was believed that 2 foot diameter deep foundations could be installed as designed using augered cast-in-place piling techniques. A brief test drilling pro-gram was conducted to evaluate the viability of 2 foot diameter continuous flight augers penetrating 22 feet into the weak sandstone. The test drilling indicated that augered cast-in-place installation techniques should be successful. Following a short delay to mobilize the additional required equipment, construction commenced. Installation of the 2 foot diameter augered cast-in-place piling to a depth of 22 feet into the weak sandstone was successfully performed.

Jan 1, 2006

Twenty field-scale tests were conducted in a 28 MW pulverized coal power plant in Healy, Alaska, to examine mill power consumption in relation to coal grind size. The intent in this field-scale study was to verify if grind size truly impacted power consumption by a detectable amount. The regression model developed from the data indicates that grind size does impact mill power consumption, with finer grinds consuming significantly more power than coarser grinds. However, other factors such as coal hardness (i.e., the lower the Hardgrove Grindability Index, or the harder the coal, the higher the power consumption) and mill throughput (i.e., the higher the throughput, the higher the power consumption) had to be included before the impact of grind size could be isolated. It was also observed that combining amperage and flow rate into a single parameter, i.e., specific amperage, hurt modeling. Cost analysis based on the regression model indicate a power savings of $19,972 per year if the coal were ground to 50% passing 76 mm rather than the industry standard of 70% passing 76 mm. The study also demonstrated that size reduction constituted a significant portion of the power consumption.

Jan 1, 2008

By P Knight, P A. Walker, H E. Speight

Pushback 8 South is the final cut back on the south wall of the East Pit at BHPBilliton?s Mt Whaleback iron ore mine in the Pilbara region of Western Australia. Development of the cutback commenced in 1999 and is now nearing completion with ultimate pit walls up to 300m high. This paper describes the geotechnical, structural and hydrogeological setting of PB8S, reconciliation between design and slope performance and the slope engineering techniques used to effectively manage the risks associated with the slope. These techniques include slope buttressing and sequential mining with waste backfilling, as well as a detailed program of displacement and hydrogeological monitoring, structural mapping and slope stability assessment. During the course of slope formation recent developments in remote slope displacement monitoring using radar and remote structural mapping using terrestrial photogrammetry have also been applied. Aspects of the PB8S slope management plan are relevant to many large scale open pit slopes. This paper provides geotechnical practitioners with information which may be helpful in managing geotechnical risk in similar environments.

Jan 1, 2006

Igneous phosphate deposits located in tropical and subtropical regions of the world are characterised by low P2O5 grades, very diversified mineralogy and intensive lateral plus vertical variations in chemical composition, mineralogical assembly, rock texture, grain size, slimes content and morphology plus surface coating of apatite particles. Those variations characterise ore types with distinct behaviour in mineral processing plants. This work reviews the main challenges to concentrate those ores, addressing developed solutions. Apatite concentration requires long chain anionic collectors to conduct reverse flotation of barite (alkyl sulfate) before direct flotation of apatite (sarcosinate, sulfosuccinate and oleate) at basic medium. The long chain collectors decrease the surface tension of the flotation solution (?LV) and a particular value of 51 mN/m was found to promote the most selective separation between apatite/gangue at a particular plant. Effective control of the magnitude of ?LV in industrial plants has not been realistic because there is a lack of reliable instruments to carry out in-situ measurements. Regarding gangue depression by starch, a review is made on possible mechanisms that promote its remarkable ability to depress some minerals (Fe-oxides, ortho plus meta silicates and calcite) vis-a-vis others (quartz, apatite and layered silicates). Flotation recovery (R) of fine (20<R<30 per cent) and coarse (30<R<60 per cent) apatite particles is considerably lower than the recovery of the intermediate ones (R>70 per cent) and inadequate hydrodynamic conditions within flotation cells are the main reasons for that behavior. Once the best hydrodynamic conditions to float coarse particles are not the same to float the fine ones, flotation of coarse and fine particles is commonly conducted at separated circuits in industrial scale. Entrainment of very fine gangue particles is an important source of contamination of apatite concentrates, mainly when weathered ores are treated. In most cases, adjustments in flotation equipment (columns or mechanical cells) promote considerable improvement in the quality of final concentrates.

Sep 13, 2010

By J. L. Howell, D. E. Pollock, A. B. Cecala, A. D. O’Brien

Dust from worker,s clothes has been shown to be a problematic source of personal dust exposure. A recently completed effort between NIOSH and the Unimin Corporation has resulted in a quick and effective way to clean worker clothing. The process involves a booth under negative pressure with an air spray manifold to supply compressed air to blow off the dust from the clothing. The overall system is designed to meet MSHA and OSHA requirements. Results of field testing indicated that the manifold cleaned the clothes 10 times faster and removed 50% more dust than cleaning methods used by workers today.

By K. E. Wood, K. J. DiRocco, L. A. Becker

The Russia Wharf segment of the Silver Line Phase II Project for the MBTA incorporated ground freezing and underpinning during New Austrian Tunneling Method(NATM) tunneling through timber pile foundations, urban fill, and abandoned wharf structures beneath two historic 7-story buildings with steel frames and masonry facades. During construction, the project team implemented an extensive program to monitor, evaluate, and mitigate the ground and building movements caused by the various construction activities. Mitigation included freeze cycling and building raising/lowering to compensate for ground movements and safely maintain the serviceability and occupancy of the buildings. In this paper, we present the history of the freeze, tunnel construction, and thaw-related movements that occurred and the building response that we observed.

Jan 1, 2005

By Paul J. Axtell

Self-hardening cement-bentontie (c-b) slurry walls were constructed as shear walls to stabilize the downstream slope of Tuttle Creek Dam near Manhattan, Kansas. The slope stabilization was required to protect the existing pressure relief well system located at the downstream toe of the dam. The wells require protection from slope deformation induced by liquefaction of the foundation sands during or immediately after the design seismic event. The shear walls are transverse to the axis of the dam, unreinforced, and relatively brittle members that may be exposed to relatively large shear strains, and possible cracking, during or immediately after shaking. An extensive laboratory investigation was conducted on recovered core samples to optimize the mix design and stabilization scheme. Furthermore, as is the topic of this paper, a portion of the laboratory investigation was to determine the large-strain, or post-peak, shear strength of the c-b material for use in limit-equilibrium slope stability analyses and numerical deformation modeling to assess the magnitude of permanent deformation caused by the design earthquake. These data may be beneficial to other projects that are considering the use of unreinforced c-b slurry walls for seismic retrofit purposes.

Jan 1, 2010

By Linneas W. Laage

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation.

Jan 1, 1995

A Process for the Flotation of Chrysocolla

Sep 13, 2010

By Z. M. Zhang

Fracture grouting is a particular technique which can be used in soils and rocks with low permeability to increase groutability and penetration rates and to solve some special foundation problems by inducing limited and controlled zones of hydrofracture surrounding the injection source. The present paper describes the basic principles of hydrofracture and its application to grouting in deep foundations, and indicates some recognitions about the mechanisms and effects of fracture grouting.

Jan 1, 2010

By S. Heukelman

Zinc or, a zinc refinery in South Africa, uses oxygen enrichment of up to 26% O2 in its fluidizing air to increase concentrate-throughput in its fluidized bed roasters. The aim of the study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining concentrate throughput rates and calcine quality. A laboratory scale fluidized roaster was used to determine the strength and oxidation kinetics of suitable micro-pellets. The strength of the pellets was determined by the extent of attrition during roasting. It was found that micro-pelletization decreases the fines in the feed to the roasters; the ?500 µm fraction decreased from 87% to 10%. The micro-pelletized particles do break down during roasting, which increases the -500 µm fraction to 31%. The general morphologies of the roasted particles are similar to those found by previous workers. Micro-pelletized concentrate particles require more time than non-pelletized concentrate particles to oxidize in the roasting step, although this is less than the mean residence time of the Zincor roasters. Roasting micro-pellets in O2-enriched fluidizing air increased the reaction rate.

Jan 1, 2011

By David Schroeder, John Chipman

Jan 1, 1964

By Herrmann Flor

In steelmaking process, where up to 70% of variable cost of finished product is already incurred, energy and refractory costs account for 45-50% of the cost of production of crude steel and contribute significantly to the carbon footprint of the end product. Any attempt to control and reduce these costs will automatically lead to more competiveness and reduced carbon emissions. Leading the technology for ECOPLANT (characterized by the fact that the economic and ecological benefits are integral part of our products), SMS has developed innovative solutions which can be applied to both new and existing plants alike. This paper reviews one of the electrical and automation concepts. Tackling the secondary gas cleaning system and hence being applicable to almost all steel plants, the X-Pact® Gas Cleaning Assistant optimizes the control of individual dampers based on modelling of fluid resistances of ductwork in gas cleaning system. It guarantees the best dust removal from work place at minimum energy consumption.

Oct 30, 2017

By Sean Gallagher

Bolting large sheets of wire mesh screen (WMS) to the roof of underground mines prevents injuries due to rock falls. However, WMS can be heavy and awkward to lift and transport, and may result in significant spinal loading. Accordingly, six male subjects (mean age =45.8 years + 7.5 SD) were recruited to lift WMS in a laboratory investigation of the biomechanical demands. Biomechanical modeling was used to estimate external moments about L5-S1 for sixteen lifting tasks, using two sizes of WMS. Full-size WMS involved a two-person lift, while half-size WMS involved a one-person lift. Lifts were performed under 168 cm and 213 cm vertical space. Restriction in vertical space increased the maximum L5-S1 extensor moment from 254 to 274 Nm and right lateral bending moment from 195 to 251 Nm. Lifting full sheets of screen (as opposed to half sheets) resulted in an average 33 Nm increase in L5-S1 extensor moment. The L5-S1 extensor moment was increased by an average of 44 Nm (18%) when lifting screens positioned flat on the floor compared to an upright position. Relevance to industry: Large flexible materials are commonly lifted in industrial work environments, and may involve the efforts of two or more workers. The current study examines the low back loading associated with lifting large flexible screens and presents recommendations to reduce spine loading.

Jan 1, 2009

By Phillip Cancilla, Daniel Roy, Frank Rosenblum

"The manual moisture determination methods employed today by mineral processing plants falls short in providing timely information required for automation control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation, that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool.A novel on-line determination system for ore concentrate moisture content would replace the normally tedious classic manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the “wish list” of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done in the classical technique of loss in weight by uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7 to 9%. Many times, delays in manually achieving reliable feedback on the moisture content results in the moisture varying from 5 to 12% before corrective actions can be made.This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper describes a unique and promising on-line moisture sensor in two mineral processing applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarize the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content."

Jan 1, 2001

By M. Rakoma

Following the blasting fatality on 17 December 2009, Landau Colliery was forced to change from the blasting practices that had been utilized since the start-up of the mine. Since then, attempts have been made to optimize blasting results. The challenge is rooted to the mining environment - during the early life of the mine, mining took place in virgin areas, whereas currently mining is taking place in areas overlying old underground bord and pillar workings. The underground bord and pillar workings aggravate phenomena such as spontaneous combustion, hot holes, and sinkholes. The 2009 fatality was attributed to hot holes causing premature detonation. Landau has been struggling with poor results from their overburden and coal blasts; leading to poor fragmentation of overburden and the PI parting that lies between the No.1 and No.2 coal seams. An extensive literature survey was completed in order to identify possible alternative solutions that could be evaluated for this unique mining environment, which demands a high degree of caution during mining to ensure factors such as dragline stability and personnel safety. The literature survey confirmed that the previous blasting technique, which was mainly characterized by air decking, was indeed the more efficient, although it was deemed unsafe because of the possibility of hot holes and the high sensitivity of detonators. Potential modifications to the blasting technique were modelled in a Microsoft Excel simulation that was available from the mine, and pit visits were conducted in order to determine whether implementation would be a problem. From the model it is evident that results can be improved by changing the current burden and spacing ratio. Visiting the pit revealed that the tie-in pattern and drilling inaccuracies are contributing to problem areas.

Jan 1, 2013

By Org de Wet

This paper summarises the strategy for selection between a two module coal plant incorporating large, but less equipment, and a three module coal plant with more but smaller equipment. The two options were evaluated in terms of three main categories: ? Size ? size of the equipment and the effect on the process efficiency as well as the difference in physical dimensions of the plant to accommodate the larger equipment; ? Cost ? capital savings between a two and a three module plant, processing the same ROM (run-of-mine) tons per hour (t/hr); and ? Practicality ? in terms of constructability of the plant, safety of using larger equipment and maintainability of the equipment. Decisions that were taken to reduce the risk associated with size, cost and practicality on the chosen option of a two module plant will be highlighted.

Jan 1, 2006

By Descour Jozef, Suguru Shirasagi, Takuji Yamamoto, Koji Murakami

For TBM tunneling no visual inspection of excavated ground is possible. This may hinder the high-speed excavation, particularly in complex ground conditions. The TBM Excavation Control System was developed for better prediction of geological conditions ahead of the tunnel face during excavation. The seismic reflector tracing produces volumetric images of anomalies in the ground in “near-real time.” These images are verified using logging data from pilot boring and TBM driving data, to improve reliability and precision of ground mapping. Also good correlation was obtained between the rock strength index computed from TBM data, and one derived from volumetric seismic images.

Jan 1, 2007

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976