Search Documents

By C. Daniel Kealy

Dissolved and suspended solids are present in the free water of tailings ponds. This Bureau of Mines study was designed to identify the influences of the slime zone in preventing these solids from reaching the environment outside the tailings pond. The finite-element method was used to determine the rate of discharge of subsurface water from the Van Stone tailings pond in northern Washington. The slime zone was sampled and tested for the first time, and results were interpreted and incorporated into the mathematical model. Computer results were verified by installing and monitoring piezometers in the field and by a simulated (16- by 1/2- by 3 foot) laboratory model. Output from the numerical model defined critical seepage zones and revealed that proper pond design and maintenance can reduce pond seepage losses to a minimum. Minimization of seepage requires maintaining the pond water level over the slime zone. Sufficient physical, chemical, and limnological data were collected and analyzed to conclude that the only realistic reflection of synergistic effects is obtained by study of the indigenous biota in combination with quantitative chemical and physical data. Proper planning and management of the milling and waste disposal operations are the key to minimal pollution.

Jan 1, 1974

By D. S. Burgess

This report summarizes the incidents that preceded the December 9, 1970, propane-air explosion in Port Hudson, Mo., and then attempts to establish the nature of the explosion from the ensuing events. Special emphasis is given to possible ignition sources, the distribution of flammable vapors, and the analysis of blast damage. Both near-and far-field damage indicated that this explosion may be attributed to the detonation of propane in air with an energy release equivalent to that from about 50 tons of detonating TNT.

Jan 1, 1973

By R. V. Ramani

Procedures have been developed which permit determining in either existing or new mines the optimum diesel equipment deployment schemes and the effect of. diesel exhaust on mine-air quality. Specifically, the following areas are covered in the report: 1. Description of diesel deployment schemes in four underground coal mines that were visited is provided. 2. Description of the analysis procedure to determine the number of shuttle cars required to maintain maximum theoretical continuous miner (or loader) production rates in typical room-and-pillar mining systems and of exhaust contamination resulting from the deployment of diesel powered shuttle cars are provided. Sensitivity analyses to determine the effect of changes in input variables on production and contaminant concentrations are also discussed. 3. Description of the analysis procedure to develop the locomotive operating parameters is provided. Assessment of both production performance as well as estimates of the magnitude of diesel exhaust contamination of the mine air are also made. 4. Recommendations for extensions of this research are outlined and include developing and testing procedures for 1) determining equipment duty cycles for the diesel equipment, and 2) studying the exhuast contamination of mine air on the basis of these duty cycles.

Jan 1, 1978

Recycling and Recovering Fine Particles from Auto Shredding Residue (ASR/SR) to Conserve Raw Materials and Protect Environment

Sep 13, 2010

By J Watt

The Hidden Valley Gold Project is located in a remote and mountainous area of the Morobe Province approximately 30 km south of the township of Bulolo and approximately 90 km south-southwest of the provincial capital, Lae. The Hidden Valley deposit was discovered in 1984 with the nearby Hamata and Kaveroi deposits discovered in 1987 and 1992 respectively. Reserves (Harmony, 2009) at these three deposits are 42.1 million tonnes of ore containing approximately 2.9 million ounces of gold and 45 million ounces of silver. A further 5.4 million ounces of gold and 84 million ounces of silver are in the resources category. The process plant is designed to treat 4.2 million tonnes per year of gold/silver ore extracted by open cut mining methods. Ore is classified into three ore types according to oxidation state: oxide, transition and primary. The silver to gold grade ratio is high for the Hidden Valley and Kaveroi ores, generally in the range 15 - 20:1, and much lower for Hamata, typically 1 - 2:1: Primary ore is the dominant ore type at Hidden Valley with sulfur grades up to about two per cent sulfur. Oxide and transition ores are more prevalent at the Hamata deposit, but its primary ore has up to five per cent sulfur grades. Variable ore types, particularly in the initial years of operation, high silver to gold ratios and limited plant site area, due to the challenging terrain, present the main processing challenges for this project. This paper describes the operating strategies and process development for the main areas of this circuit, highlighting selections of processes and equipment that achieve cost effective, yet flexible solutions to the treatment of ores from these deposits.

Jan 1, 2009

By Erin Legault Seguin, Mike Rylatt, Curtis Mohns

"With energy costs increasing and ore grades diminishing, the role of pre-concentration in hard rock mining operations has been gaining greater interest. To maximize energy conservation, the pre-concentration process should be conducted at as coarse a crush size as possible while minimizing losses of pay metals. Dense medium separation (DMS) is a robust process that can be conducted at particle sizes as coarse as 300 mm and as fine as 500 µm with high separation efficiency, depending on liberation characteristics of the value minerals. The DMS process involves three steps: feed preparation, dense medium separation, and ferrous-based media recovery. This paper discusses each of these processing steps, but focus will be given to the dense medium separation stage. Various types of DMS equipment are reviewed. Pilot plant campaign case studies conducted at the SGS Lakefield site are presented, which have included a variety of mineral systems such as spodumene, sulphide-bearing gold ores, and complex sulphide ores. These case studies demonstrate that for amenable ores, mass rejection of 20-60% is possible while maintaining recoveries of greater than 90% in most cases.IntroductionPre-concentration is a process of rejecting mass of gangue while ensuring recovery of valuable minerals prior to more intensive, downstream processing. Pre-concentration has been practiced in industry for many years, and is gaining greater interest as the industry copes with processing lower grade, more difficult ores, typically requiring finer grind sizes and higher energy costs."

Jan 1, 2016

By J. M. Toguri, K. Grjotheim

It is known 1,2 that the equilibrium between titanium metal, TiCl2 , and TiCl3, in a solvent of molten metal chlorides, is influenced both by the total amount of dissolved titanium and by the type of solvent. Assuming that the trivalent titanium forms the complex ion Ti111 Cl4, the equilibrium reaction may be expressed by the following equation, (Me) TiIII cl4+ 1/2 Ti = 3/2 TiII cl2+ (Me) Cl The ideal ionic equilibrium constant for this reaction is, Where the N's are the molar ionic fractions in the equilibrium melt, and (Me) the different types of cations present in the equilibrium mixture. The following thermodynamic relation is derived between Kand the concentration of cations in the equilibrium melt, mix The N"S are the equivalent ionic fractions, and so forth are constants corresponding to the standard changes in free energy for reactions in melts where only the cation indicated is present, and f (y1) is a function of the activity coefficients in the equilibrium mixture. When this term vanishes, a simplified linear relationship between In Kideal and the concentration is obtained. The simplified relationship has been applied with satisfactory results to the experimental data of Mellgren and pie,' and Kreye and Kellogg.2 MANY existing methods for the production of light metals involve the reduction of their respective metal halides in the presence of salt melts composed of alkali or alkaline earth chlorides. In such a solution phase, the light-metal halide may undergo stepwise reduction from a higher, to a lower valence, and finally to a zero valent state. In this connection, the disproportionation equilibrium is of great interest. In the case where the higher valence is three and the lower valence is two, the disproportionation equilibrium may be written as follows, 3 Me11 = 2 Me111 + Me [I] If this equilibrium occurs in a salt melt containing a large excess of alkali chlorides, a typical ionic melt is obtained. It is then possible to formulate the cation equilibrium: 2 Me+h' + Me = 3 Me++ [II] Reaction [11] is analogous to a cation exchange reaction. It has been shown thermodynamically that the equilibrium constant for such a reaction in 2

Jan 1, 1960

By S. Weiss, E. Espinoza

The El Sauzal gold-silver deposit is a high-sulfidation, epithermal precious-metals deposit hosted by an east-dipping sequence of dacitic and rhyolitic pyroclastic and debris-flow units of probable Oligocene age. Total gold production since startup in late 2004 is approximately 450,000 oz. of gold. Above the sulfide boundary gold is mainly disseminated as small grains interstitial to alunite, kaolinite and quartz. The majority of the ore is found in quartz-alunite-kaolinite altered rock that mantles tabular to irregular silicic cores of vuggy, residual quartz ±kaolinite ±dickite. Grade domains are modelled as subhorizontal to east and southeast-dipping. Higher-grade domains cut across alteration zones and also coincide with transitions from vuggy quartz to quartz-alunite-kaolinite. The highest grades are commonly found marginal to vuggy quartz in transitional, hematite-rich quartz-kaolinite and quartz-alunite-kaolinite rock.

Jan 1, 2007

Sulphuric acid leaching at atmospheric pressure of a number of Australian nickeliferous laterites was examined in detail. The results obtained indicate that nickel can be extracted from these ores, although the conditions required to achieve about 90 per cent extraction vary widely. These differences in reactivity can be related to the types of nickel-bearing minerals present.Nickel is more readily extracted from nickel-bearing clays such as chlorite, than it is from nickel-containing goethite.The results clearly show the problems associated with the processing of complex ores such as the nickeliferous laterites, and they indicate the need for complete characterization of each deposit.

Jan 1, 1978

By T S. Giraudo

The Macraes Gold Project, operated by GRD Macraes Limited, engaged GRD Minproc Limited to assist with the evaluation of a pressure oxidation circuit, this being the key component of a recovery enhancement project. The initial study gave sufficient confidence in the process to enter into project execution. GRD Macraes Limited was the first company to license Newmont Mining Corporation's pressure oxidation technology, which aims to improve gold recovery from the carbonaceous sulfidic flotation concentrate. This paper outlines the fundamental chemistry of the process followed by a description of the plant that was ultimately installed. A summary of the commissioning is given together with an overview of the production results to date. The project ramp-up was rapid, with design temperature and throughput being achieved within days of hot commissioning. Gold recoveries have exceeded expectations, improving from around 70% prior to the installation of pressure oxidation to above 84%. The project has increased the nominal gold output at Macraes from 120,000 oz/y to 170,000 oz/y. On-going plant optimisation for process parameters is discussed, giving rise to flexibility in gold production, with key controlling parameters exceeding design.

Jan 1, 2000

By J. M. Riley

This report summarizes Bureau of Mines experiments in purifying sulfate leach liquors, which were prepared from low-tenor beryl concentrates by modifying the Degussa process. The leach liquor was prepared from a beryl concentrate containing 2.7 percent BeO by (1) sintering the beryl concentrate with limestone in a rotary kiln at about 1,150° C. and by (2) treating the sinter first with sulfuric acid and then with water to form and extract beryllium sulfate. About 80 percent of the beryllium was dissolved. The resulting leach liquor contained 2.4 grams of BeO, 20 grams of Al203, and 6 grams of Fe203 per liter. The laboratory solution contained much more aluminum and iron than a solution derived from treating 10 percent BeO concentrate, which is the standard raw material used by industry. Tests were made to determine the behavior of the solution toward alum purification and limestone neutralization both of which were employed industrially in conventional Degussa procedure.

Jan 1, 1962

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007

Greater use should be made of lineations in investigations of the engineering properties of rock masses and in structural studies guiding prospecting programmes.A prominent alignment of elongate mineral grains and stretched pebbles usually marks the primary direction in which metamorphic rocks have been extended by flow. In local adjustment zones separating masses that have extended different amounts, this lineation has been a direction of slip. Kinks and crumples resulting from this slip lie in secondary lineation directions transverse to the primary mineral lineation.During deformation relatively mobile materials move into dilatant zones caused by irregularities in primary flow directions. This secondary movement transverse to lineated, primary-flow directions is the cause of crenulations and folds with axes parallel to flow lineations.INTRODUCTIONThe arrangement of inequidimensional particles in rocks is rarely statistically random. Platy minerals tend to be parallel to bedding and foliation planes. Elongate particles and linear structures lie most frequently in certain lineation directions. The types of elongate particles in lineated rocks include needle and blade shaped mineral grains, sheared out segregations, and stretched pebbles, amygdules, and aolites.Crenulations and kinks are the most common of the linear structures involved.Faint lineations are readily overlooked. Even strong lineations have been ignored. This is unfortunate as even weak lineations may be important.Use of lineation information Well-developed lineations influence the mechanical properties of rocks. Quarry workers have long known that the mechanical properties of rock masses vary directionally...

Jan 1, 1965

By Lawrence F. Johnsen

In 1989, the Connecticut Department of Transportation authorized the evaluation and design for a reconstructed Route 1 bridge over the Quinnipiac River in the City of New Haven, Connecticut. The project extends from the intersection of Route 1 with East Street, easterly for approximately 3/4 mile to the intersection of Route 1 with Wheeler Street and Stiles Street. The reconstructed roadway will be relatively on-line and widened to provide for four lanes of vehicular traffic and a single-track railway line. The existing bascule bridge and approach spans, which were constructed in 1924, will be replaced by a 270-foot span lift bridge and new approach spans. The lift bridge will have a main lift span weighing approximately 3000 tons, second largest after the Burlington Northern Bridge over the Williamette River in Portland, Oregon. The new bridge will widen the navigation channel to 24 0 feet and provide vertical clearances of 13 feet when closed and 62 feet when open. The project is located in an industrial area. Adjacent properties include retail gasoline sales, auto repair, railroad transport and bulk storage of petroleum. Existing structures include the Yale Boathouse and several retaining walls serving as containment dikes for petroleum storage tanks. The Yale Boathouse, located on the east bank of the river, was constructed in 1909-1910 and is eligible for listing in the National Register of Historic Places.

Jan 1, 1993

By J L. Maule, S J. Mathews, K A. Rodgers

Gold and Silver bearing epithermal veins of the Golden Cross deposit are hosted in Miocene and Pliocene calc-alkaline volcanics occurring 8 km northwest of Waihi at the southern extent of the Coromandel Peninsula, North Island, New Zealand. Veining occurred during a period of hydrothermal activity that began early to late Pliocene, and possibly continued into the Pleistocene.   Field relations and petrographic relationships reveal that multiple generations of FeS2 occur in the Golden Cross region, with FeS2 occurring in all nine rock types recognised at Golden Cross. The variability of FeS2 morphology was investigated by preparation of high purity FeS2 separates, and grain counting. Marcasite is the dominant FeS2 phase at Golden Cross, and along with pyrite is shown to have a systematic habit variation. Pyrite shows a sequence from cubes through octahedra to pyritohedra to dendritic growth. This pyrite sequence conforms to an experimentally determined sequence. The parallel sequence for marcasite at Golden Cross is from tabular through bladed aggregates to euhedral miscellaneous marcasite morphologies. The FeS2 sequences observed are believed to be due to increasing temperature, and perhaps also increasing FeS2-oversaturation and fluid flow.

Jan 1, 1994

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 km. Some 500 km south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 km. The Complex was emplaced at several centres along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite. Except in the lower units of the Ultramafic Series sulfide mineralisation is widespread. Pyrrhotite is the dominant sulfide with lesser chalcopyrite pentlandite and pyrite. Four significant zones of sulfide accumulation are recognised and discussed in some detail. Evidence suggests that the primary magma from which the Riwaka Complex was derived was sulfur deficient. It is concluded that the sulfur content of the Riwaka Complex was derived from assimilation of sulfur rich wall rocks during intrusive processes.

Jan 1, 1980

The uptake of zinc, lead, and copper by the flora of the Tui Base Mine area near Te Aroha is described.Vegetation and soil samples were taken from two traverses across the Raukaka Lode. Results. after statistical analysis, indicated that Beilschmiedia tawa was a suitable species for biogeochemical prospecting for lead and that SchefJlera digitata was satisfactory for zinc.The tawa showed a negative anomaly for lead over the vein itself but not over the adjacent dispersion halo. It was concluded that lead concentrations greater than 230 p.p.m. in the wood ash of the tawa and zinc concentrationsgreater than 540 p.p.m. in the leaf ash of S. digitata denoted threshold values for anomalous mineralization in the soil beneath. Although both species contained copper, neither indicated a soil anomaly for this element.

Jan 1, 1969

By Takashi Sasaoka

The PT. Adaro Coal Mine targeted in this research is located in South Kalimantan, Indonesia. The coal production of this mine is increasing year, with about 35 M tons of coal produced in 2006. This mine faces many ground control problems, especially instability of the footwall. Large-scale landslides occur often in the footwall; this may be because of weak rock and the effect of footwall rock weathering. Hence, prompt measures must be developed and followed in order to preserve the stability of the footwall and make this mine safe. Additionally, the final pit design is now being reconsidered because of the increasing demand for and high price of coal. With these issues in mind, this paper describes a solution for improving the stability of the footwall and discusses the final pit design based on the results of an on-site investigation and numerical analysis.

Jan 1, 2008

By Robert Boyd

The Diamond Markets ? Supply has continuously increased over the past 25 years ? However, global supply is expected to drop by 1 to 2% by 2015 ? Demand Driven Market ?Demand is expected to grow 3% annually through to 2015 ? Supply Squeeze Anticipated (2010 to 2015) ? Consumption is exceeding rate of discovery, mine development and reserve replacement ? These fundamentals are driving increased capacity and production at existing mines in South Africa, Botswana and Russia and new areas such as Canada ? Canada is now the third largest diamond producing country in the world ? These fundamentals are also driving record levels of exploration expenditures throughout the world with particular focus on Africa and Canada

May 1, 2006

The re-use of waste water from coal preparation plant tailings is always desirable, but is generally problematic in terms of solid-liquid separation. Dewatering and disposal of coal slurry at a high percentage of moisture poses a major technological and environmental challenge to mining and mineral processing industries world-wide. Characterization and flocculation of these coal tailings reveals that the separation of fine coal tailings depends on factors such as size distribution, slurry viscosity, zeta potential, pulp density, circuit design, plant operating parameters, and the behaviour of solid particles in an aqueous medium. The present study was carried out on -600 mm coal tailings collected from a coking coal preparation plant of Jharia Coalfield, India, using anionic flocculent. Characterization studies revealed that the zeta potential was highest (-44 mV) at a pH of 9.0, the size range of the particles was 1.1?700 m, and the average ash content was 62.57%. Flocculation studies were performed at different solid concentrations, pH values, and polymer dosages. The results indicated an efficient settling rate of 178.15 mm/min at 8% solid (w/w) at a flocculent dosage of 32.50 g/t solid. The turbidity of the clear liquid obtained was 7.42 NTU.

Jan 1, 2014