Search Documents

By John E. Newby

The Brightwater Conveyance System consists of four tunnel segments in three tunnel con-tracts, comprising over 21,760 m (71,400 ft) of pressurized face tunneling in complex glacial and non-glacial soft ground conditions with a large proportion 60 m (197 ft) or more below the ground surface with up to 7 bars groundwater head. This resulted in unique technical challenges for establishing geotechnical baseline values. The process used to develop these baseline values and specifications with regard to the level of risk that the owner, King County, was willing to accept is described in this paper.

Jan 1, 2008

By C. J. Beevers

Tlze influence of zirconium hydride precipitate mprphology on the fructure of Zr-H alloys tested at strain rates of 10- sec at 20° and - 196°C and at strain rates of -500 sec.-1 at 20°C has been inves-tigated. The critical stage in the embrittlement of these alloys was the fracture of the zirconium hyhide precipitates to form large interval cracks at a stress of 25,000 10 137,000 psi. In specimens con-temping up to 100 ppm H the preciptates existed as isolafed platelets in the zirconium matrix and their fracture as enhanced by low temperature (—196°C) and high strain rate (-500 set-f) loading. These resl~lts lead to the conclusion that the rate of strain hardening of the zirconium metal controls the frac-tzrm of the hydride platelets. Increased hydrogen contents of 500 to 2000 ppm resulted in an increase in the 1)volume fraction and size of precipitates and crlso led to crack propogation in the hydride at both 20 and —196C at the low strain rates (10'* sec-'). Quenching led to refinerment of hydride precipitate size and reduced the degree of embrittlement at — 196°C; this effect is attributed to the absence of fracture of the fine precipitates. The formation of zirconium hydride precipitates has been shown to be the cause of hydrogen embrittlement of zirconium.' Several investigators'-" have studied the problem in broad outline, demonstrating that impact-loading conditions, testing temperatures below room temperature, and increasing hydrogen content produce increased brittleness. For example, Muehlenkamp and schwope2 showed that the transition temperature for notched impact tests was raised from 150" to 350°C on increasing the hydrogen content from 45 to 490 ppm. The degree of embrittlement is also controlled by the morphology of the zirconium hydride precipitates. The solubility of hydrogen in zirconium decreases from 600 ppm at 550°C to 10 ppm at 20"C,~ so that the form of the zirconium hydride precipitates (ZrH2) can be modified by varying the cooling rate through the Zr-aZr + ZrH2 phase boundary.= Forscher showed that quenching a specimen containing 35 ppm H from above 315°C resulted in a reduction in area of 70 pct at -196"C, whereas slowly cooling from above 315°C resulted in a ductility of half this value. The role of the hydride precipitate in the fracture process has been examined by Young and schwartz6 and more recently by westlake.' From metallo-graphic observations on slowly cooled Zr-H alloys they have suggested that cracks are nucleated in the hydride precipitates by the interactions of twins in the zirconium metal with the hydride. The experiments reported in this paper show that crack propagation in the zirconium hydride precipitates is the critical stage in the embrittlement of Zr-H alloys. The factors influencing fracture of the hydride precipitates and crack propagation in the zirconium metal will be related to the problem of embrittlement. EXPERIMENTAL TECHNIQUES The zirconium used in these experiments was produced from an ingot of vacuum arc-melted iodide zirconium forged down to 1 in. diameter at 800' to 850°C. The 1-in.-diameter bar was surface-machined and cold-swaged to 0.375 in. diameter. After a vacuum anneal at 800°C for 1 hr the hardness was 60 to 70 Vdh. The total impurity content was approxi-

Jan 1, 1965

By S. Felderhof, W. S. Vaughan

"Over the years, it has been increasingly difficult for the minerals industry to raise the necessary capital for its activities. To alleviate this phenomenon, complete transparency and capital market efficiency is needed. Since a company’s mineral resources and mineral reserves base is an essential component to obtaining capital, reporting these assets must also be transparent and efficient. This must occur, however, at an international level given that mineral industry operations, and its financing, are international. To achieve this, an international committee (i.e. Australia, Canada, South Africa, the United Kingdom and Europe, and the United States) was formed and has been developing standards for the reporting of mineral resources and mineral reserves.The effectiveness of these standards, however, depends on adoption by the required regulators. Unfortunately, these standards have not been recognized by the U.S. Securities and Exchange Commission (SEC). Instead, the SEC adheres to its old standard (Industry Guide 7), making it increasingly expensive and difficult for international mining companies to obtain capital in the United States. Compounding the problem is the SEC’s influence over the current work of the International Accounting Standards Board and the International Organization Organization of Securities Commissions. These organizations are in the process of standardizing international accounting practices and international securities rules and regulations. Their current position may prevent adoption of the industry-developed mineral resources and mineral reserves standards which are internationally recognized."

Jan 1, 2005

The major proportion of South African coal is extracted by the bord-and-pillar mining method which requires that the overlying strata be supported by pillars of coal. The stability of the pillars is a major safety concern. One of the factors which affects the strength of coal pillars is the intensity and nature of discontinuities in the coal seams. Current design methods for pillars assume that al the coal seams have equal strength and are equally disturbed by natural discontinuities, resulting in over-designed pillars in some cases and potentially unstable pillars in others. Research was carried out to determine the nature of discontinuities in coal seams and to assess their potential effect on pillar strength. It was found that large variations exist in the intensity of discontinuities in the different coal seams being mined. In addition, numerical model studies showed that the discontinuities could significantly reduce pillar strength if the width-to-height ratio of the pillars is small, but the effect decreases as the width-to-height ratio increases.

Jan 1, 1997

By P. G. Semple

"In January 1985, Equity Silver Mines Limited began operation of a cyanidation circuit to scavenge precious metals from the flotation tailings. At present, this process is treating 270,000 tonnes of tailings per month and is recovering in excess of 0.20 grams of gold per tonne. To obtain these results Equity is operating a carbon-in-leach circuit that utilizes pressure stripping, zinc precipitation acid washing and thermal reactivation. A cyanide destruction circuit is also required to minimize the deleterious effects on reclaim water in the flotation stage. This paper describes the existing scavenger plant, and details the start-up problems encountered and the modifications made to correct these problems.INTRODUCTIONEquity Silver Mines Limited , a 68% owned subsidiary of Placer Development Limited , is located 38 km southeast of Houston in north central British Columbia. The geographic location of Equity Silver Mines is shown in figure #1. In September 1980, production first began with the ore being supplied from the Southern Tail open pit. In March 1984, the Southern Tail deposit had reached its economic pit depth, and since then ore has been supplied by the Main Zone pit the gold mineralization in the Main Zone is less refractory than the Southern Tail and cyanidation of the flotation tailing appeared to be a viable alternative.An extensive test program was undertaken and the results confirmed that considerable gold and silver values were amenable to cyanide leaching. A feasibility study showed that these values could be economically recovered and the detailed engineering work began."

Jan 1, 1987

By F. A. Camisani-Calzolari

The latter half of the 20th century has seen the proliferation of a series of codes to address commodity needs which were brought about by rapidly advancing technologies and the globalization of markets and consumerism. This paper addresses the specific needs and the origin of this surge and presents these codes in the context in which they were developed. It also compares the main codes or groups of codes and elaborates upon their strengths and weaknesses. Three main categories of codes are identified, namely codes for reporting to international agencies, codes addressing government needs and, finally, codes for the investors and the stock market. Codes governed by international agencies usually relate to strategic commodities which have highly specialized fields of usage such as nuclear power generation where international cooperationis eventually the only viable approach for both the development of technologies and their applications. Codes for reporting to governments address the necessity of each state to exploit its mineral potential profitably and to secure the preservation of wealth for future generations. Reporting to investors is experiencing a considerable popularity as of late because of globalization in mining and the growing need for outside financing of mining projects, whose capital requirements are getting out of reach for the average mid-cap mining company. All these codes have advantages and shortcomings dictated by the specific circumstances under which they were developed, therefore necessitating the definition and implementation of some kind of international standard whereby investments and the spread of information across political boundaries would be facilitated. Though none of these codes might ever become international in the true sense of the word because of significantly different legislations at national level, a step that would greatly contribute to the cross-border disclosure of information would be the reciprocal recognition of competent persons by the major mining countries, including China and Russia. It is also becoming essential that financial institutions and investors be properly advised on mining projects by reporting reserves and resources in a transparent and responsible way with the relevant public disclosures being compiled by professionals who take full responsibility for their submissions. Keywords: reporting codes, mineral resources, mineral reserves, competent person, UN Framework Classification, IAEA classification, JORC Code, SAMREC Code and CRIRSCO.

Jan 1, 2004

By J. M. Wempen

Booster fans in underground coal mines are often located using the concept of a neutral point. Normally, intake airways are maintained at higher absolute pressure than return airways, so air leaks from intake to return. By adding a significant pressure force to a region of a ventilation system, booster fans installed in a return airway can increase the pressure in the return so that air leaks from return to intake. This is commonly referred to as recirculation. The neutral point occurs at the location in the system where the pressure difference between the intake and the return airway(s) is zero and at this point there is no leakage or recirculation. Ideally, placing a booster fan near the neutral point minimizes leakage and recirculation; however, in practice the position of the neutral point is not static and it changes as the ventilation system parameters change. This paper presents a study of how changes in the system parameters affect the location of the neutral point in a model coal mine ventilation system. First the effects of booster fan pressure and location on the neutral point are evaluated. Next the effect of increasing mine distance, and therefore mine resistance, on the location of the neutral point and the magnitude of recirculation is evaluated.

Jan 1, 2012

By P. A. Olubambi

The leaching of zinc and copper from Nigerian bulk sulphide ore with sulphuric acid in the presence of hydrogen peroxide was studied. The aim of the study was to investigate the effectiveness of hydrogen peroxide as an oxidant for the sulphuric acid leaching of zinc and copper from a complex sulphide ore. Distribution of elementals within the various particle sizes was initially determined by ICP-OES and XRF to provide a basis for explaining the dissolution process. The effects of concentration of hydrogen peroxide, particle size, stirring speed, and leaching time at a constant temperature of 298K were studied. There were variations in elemental and mineralogical composition within the different sizes. The concentrations of zinc and copper reduced as particle size decreased while silica, sulphur, iron and lead contents increased. Dissolution results showed that the leaching rate of copper was lower than that of zinc. The highest recoveries of zinc and copper were obtained at a leaching time of 180 minutes, stirring speed of 160 rpm, particle size of 75 µm and a concentration of 1M H2SO4/1MH2O2. It was observed that the leaching rate of zinc and copper increased with increasing hydrogen peroxide concentration. Increased stirring speed had a negative leaching effect as it promotes hydrogen peroxide decomposition. Keywords: Nigerian sulphide ore, zinc, copper, hydrometallurgy, sulphuric acid, hydrogen peroxide.

Jan 1, 2006

By John N. Cunningham

Despite the wide use of micropiles for rehabilitating and retrofitting existing structures, little is known regarding the load-transfer distribution of grouted micropiles in various soil deposits. The rehabilitation of a concrete-frame warehouse in Portland, Oregon, required provisions for the seismic restraint of a new shear wall; the installation of two micropiles was specified to meet project requirements. The micropiles were uncased, 19-m (63-ft) long, 200-mm (8-in) nominal diameter, and reinforced full-length with a 64-mm (No. 20) diameter hardened steel threadbar. Due to space limitations, a sacrificial, instrumented micropile was installed near the two production piles to verify design assumptions. This paper describes the geologic setting of the project within the unsaturated Missoula Flood deposits, instrumentation, load-displacement behavior, load transfer, and Beta-coefficients for the sacrificial micropile.

Jan 1, 2011

By R Simcock

Why Rehabilitate? Legislative Requirement Land rehabilitation is a condition of resource consents for mining. Clause 17 (1) of the Resource Management Act 1991 (duty to avoid, remedy, or mitigate adverse effects) provides the legislative basis for local authorities to impose resource consent conditions requiring land to be rehabilitated to approved uses during and after mining.

Jan 1, 1997

The Mineral Sector Development Project, sponsored by the World Bank, has been set up to revise the legal, regulatory and fiscal framework for the minerals industry in Tanzania, with a view to attracting mining companies and investors to the country and facilitating future minerals development. One component of this project, the Environmental Management Framework for the Mineral Sector, was awarded to Wardell Armstrong of the UK and ENV Consult of Tanzania. In developing a new framework of environmental regulations, emphasis was placed on developing realistic standards which reflect local conditions and prevailing values. The main corner-stones of this approach are; effective environmental impact assessment procedures; establishment of environmental management procedures; and monitoring and auditing of companies? performance. The favoured approach involves a three-tier framework, as follows: ?Framework environmental provisions within the new Mining Act; ?Regulations covering more detailed environmental requirements ?Guidelines and/or Codes of Practice, which may in future become regulations in their own right. Careful consideration has been given, in developing the framework, to the limited resources likely to be available for implementation to the Ministry of Energy and Minerals and this has influenced the approach that has been adopted. This paper outlines the main components of the environmental management framework and discusses some of the important issues raised by these proposals.

Jan 1, 1998

By L. Forsbacka, M. Nakamoto, L. Holappa

Viscosity of the slag is one of the central parameters when producing FeCr in submerged arc furnaces. It contributes to smelting behaviour and reduction kinetics of chromite ore as well as to the Cr recovery by influencing the separation of dispersed metal droplets from the slag. A typical FeCr process slag contains 5-10pct chromium oxides, CrO and CrO1.5. The neural network computation was applied to the evaluation of viscosity for slags containing chromium oxides, and the prediction of viscosity in FeCr process slag was conducted. The main results in this estimation were that the chromium oxides in FeCr process slag lower its viscosity, and that the effect of CrO on the viscosity decrease is greater than that of CrO1.5.

Jan 1, 2007

By A. Lashagri

This paper presents research results on assessment of environmental impact of digging and loading equipment in surface coal mining. Environmental impact is accessed through the equipment exhaust and dust emissions, and sound level. Exhaust emission is related to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx), and volatile organic compounds (VOCs). Dust generation is expressed through the particulate matter PM10 and total suspended particulate matter (TSP), while sound is presented through the sound pressure level. Modeling of environmental impact of digging and loading equipment is conducted in Microsoft Visual Studio.NET software package. This research is a part of a boarder project on development of software system for the selection of productive, cost-efficient and eco-friendly mining systems, which is sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). The research work presented here may be used by mining professionals to aid in quantifying environmental impact of digging and loading equipment and determinate strategies for reducing its overall impact.

Feb 27, 2013

Existing processes for the recovery of platinum group metals (PGM) from UG-2 ores place stringent requirements with regard to chromite content upon feed material to the plant. An alternative hydrometallurgical process for which this is not an issue is proposed that involves reductive roasting of the ore followed by leaching with HCl/chlorine, ion exchange, and recovery of PGM from the ion exchange eluate by reduction. Problems associated with leaching of PGM are discussed and results of laboratory testwork for each of the process steps are given.

Jan 1, 2004

By D. Komljenovic, J. Paraszczak

"This paper presents the use of queuing theory in truck fleet sizing in open pit mining operations. In the first part, a methodology is developed by which an optimal ratio between the size of shovels and trucks may be determined. The second part gives the fundamentals of the queuing theory and its application in analyzing shovel and trucks. The stochastic character of involved times (loading, truck cycle, etc.) is taken into consideration. Using the above theory, the optimal truck fleet size in actual conditions may be estimated. Minimal operating cost of the working system (shovelstrucks) represents the basic requirement of the analyzed process. The methodology was validated on Caterpillar front-shovel – truck combinations. IntroductionLes camions représentent probablement les équipements les plus utilisés pour le transport dans les mines. Le coût de transport peut parfois atteindre 50 % du coût d’exploitation et 25 % du coût total (Collins, 1996; Kennedy, 1990). Il est critique pour une opération minière de le minimiser. C’est un sujet qui a été traité relativement souvent dans la littérature spécialisée. Les premières applications informatiques dans l’industrie minière ont été développées pour la détermination du temps de cycle des camions.Au fil des ans, la capacité des camions a augmenté et, aujourd’hui, les plus gros manufacturiers de camions (Caterpillar, Orenstein & Koppel, Euclid, Terex, Unit Rig, Komatsu, Liebherr, Belaz) fabriquent des camions ayant une capacité de 200 t et plus dont quelques-uns d’une capacité supérieure à 320 t. Pour les plus gros camions, le coût d’opération peut même dépasser 240 $US/heure dans des conditions modérées (Caterpillar, 1999). Les mines modernes de grande taille peuvent posséder plusieurs dizaines de camions dans leur flotte."

Jan 1, 2004

Ferrochrome is the major chromium source for stainless steel production, and submerged-arc furnaces (SAF) are most commonly utilised to smelt chromite ores into ferrochrome by using suitable carbonaceous reductants such as coke. Because of the complexity of feed structure and electrical-thermal-chemical interactions, there exist large gradients and wide distributions of temperature, mineralogy and other process variables in the furnace. This leads to various zones in the furnace, and different reduction mechanisms. Control of the furnace is thus often difficult due to the complicated physical and chemical situations in the furnace. The temperature profile in the submerged arc furnace has a great influence on the reduction rate and the production efficiency. Therefore, the energy generation through electrical arcs submerged in the solid feed and its distribution within the packed bed play an important role. In the present paper, an overall process model is illustrated to simulate inter-linked transport processes of fluid flow, heat transfer and reduction kinetics within the submerged arc furnace. The application of reaction kinetic data to simulate the chromite pellet/lumpy ore reduction with CO gas is presented and further adjusted to provide a submodel for a flow and heat transfer simulation for the packed bed by using computational fluid dynamics (CFD) technique. The comprehensive process model is aimed to simulate materials and gas flow, temperature and energy distribution throughout the furnace system. A preliminary model for gas flow and temperature distribution for the upper part of a 20 MW furnace (the packed bed) for high carbon ferrochrome production has been developed under simplified conditions. The integration of the reaction kinetic model into process simulation, and the future vision for a more comprehensive process modelling are discussed. It is expected that better understanding of the furnace insights through process modelling will help process optimisation and furnace control.

Jan 1, 2004

By A. Nel

The gold mining industry in South Africa stands to benefit much from the implementation of the self-directed work team concept. Its introduction implies flatter hierarchical structures, empowerment of the workforce and increased participation. Research indicates that half of the initiatives to implement self-directed work teams, however, fail, and it is therefore imperative for companies to be aware of the factors impacting on the effectiveness of self-directed work teams in order to focus on these early in the implementation phase. The objective of the study was to qualitatively determine these factors. Semi-structured interviews based on the phenomenological method were carried out. The sample included members of, and individuals involved with, self-directed work teams (N= 26) from a large gold mining company in South Africa. Results show that most respondents rated the availability of resources to do their work as the most important factor affecting their effectiveness.

Jan 1, 2006

By M. Mirnezami, D. Lascelles, J. A. Finch, E. El-Ammouri

"In a previous publication, the depressant action of Mg above pH 10 on Cu-activated sphalerite was described (Lascelles et al., 2001). In the present communication, a second role, aggregation is introduced.Aggregation (i.e., the tendency of particles to cluster) is measured using settling rate and turbidity converted to an aggregation index (AI) where 0 corresponds to dispersed and 1 to aggregated. Surveys of Cu and Zn flotation stages at four concentrators showed the A1 increased significantly above pH 9. The metal ions identified in the process waters, principally Ca and Mg, were tested to determine which might be responsible. The presence of Mg was found to be the most important, 50 ppm Mg having a greater impact than 500 ppm Ca fkom pH 9 to 1 1. In one plant, poor repeatability in A1 was suspected to be related to varying Mg levels; doping with Mg significantly increased AI.In both aggregation and depression, therefore, the common feature is the impact of Mg at pH > 9. Over this pH range Mg forms a range of hydroxy species, including Mg(OH)2 precipitates. Suggested aggregation and depression mechanisms associated with these precipitates are introduced. Possible problems and opportunities arising from the findings are discussed.INTRODUCTIONProcess waters in flotation circuits contain a variety of metal ions that may introduce unwanted activation or depression. Two common metal ions are calcium and magnesium. Typical concentrations are in the range 50 ppm Mg and 500 ppm Ca (Marticorena et al., 1994, Basilio et al., 1996, Negeri et al., 1997, Nesset et al., 1998)."

Jan 1, 2002

By Alan J. Lutenegger

Some years ago, a method was developed to incorporate a grout column around square-shaft helical screw-piles and anchors to increase shaft buckling resistance under compression loading. An additional benefit of this grouted shaft is to increase the load capacity in both compression and tension, depending on the geometry of the lead helical section and the soil conditions. Because of the unique construction procedure, the contribution of the shaft to the total capacity has largely been unknown. The behavior of grouted shaft helical anchors in clay was investigated by performing full-scale axial uplift (tension) load tests on a series of anchors installed at the University of Massachusetts Geotechnical Test Site. In order to isolate the contribution of the grouted shaft to the total load capacity, anchors were installed with a wooden dowel connection between the lead helical section and extension sections on three of the four anchors so that only the shaft resistance would be measured during the load tests. The grouted shafts ranged in length from 10 to 30 ft (3 to 9 m). Initial tests were performed approximately 5½ months after installation. Nearly four years after the initial tests were performed, the tests were repeated to evaluate any significant change in capacity with time and/or repeat testing (preshearing). The soil conditions at the site are presented along with the load-displacement curves for both the initial and repeat teats and a discussion of the analysis of the results. Repeat load tests showed an increase in capacity from the initial testing, however the percent increase was not the same for all depths. The results demonstrate that considerable shaft resistance can be developed in clays from the grouted shafts as might be expected. Depending on the L/D ratio of the shaft and the contribution of the lead helical section, at working loads the shaft capacity can dominate the behavior.

Jan 1, 2011

By Michael Allen, Paul Worsey

In underground blasting, the pull of the initial cut is the limiting factor for the success of the rest of the round. By improving the pull of the first cut, a critical step is made towards improving the entire round. This project attempted to optimize a burn cut’s effective pull by varying the depths of the relief holes in the burn. The effect of varying the depths of the relief holes was investigated, including depths longer than that of the cut’s charged holes. The overall objective was to consistently achieve greater pull than in a standard burn, using an identical amount of explosives. Increased pull results in savings of both time and cost in underground heading advance.

Jan 1, 2015