Search Documents

Analysis for pillar extraction potential (A-PEP) is an intelligent tool, which could be used as a preliminary output indicator when considering the secondary extraction of regional support pillars in the Witbank and Highveld coalfields of South Africa. The safe and economic extraction of underground coal pillars is of paramount significance and importance to the South African coalmining industry to ensure continuity of supply of this fossil fuel. Pillar extraction practices in South Africa have been responsible a significant proportion of safety and fatality statistics in relation to its relative output (less than 5 per cent of total South African coal production) and, as a result, research was undertaken in local pillar extraction operations and extended to similar operations in New South Wales, Australia to assess a way forward for pillar extraction in South Africa. It was found that, although little in the way of new technologies has emerged in this field in the recent past, significant contributions could be made in the field of risk analysis to obtain a generic design methodology for pillar extraction in South Africa. The resultant A-PEP tool to assess pillar extraction potential is based on certain physical, risk and economic factors, which combine to indicate operational success in terms of economic, health and safety attributes. At the time of A-PEP?s development there was alack of operating underground coal pillar extraction operations, which made it difficult to validate its applicability. Since then, however, A-PEP has been successfully tested and validated against two unique underground coal pillar operations, which is the discussion of this paper. One operation is situated in the Witbank coalfield and is extracting pillars, which are 20 years old and at a depth of 80 metres below surface, while the other operation is situated in the Highveld coalfield-which is extracting 6 month-old-pillars underneath a massive dolerite sill at a depth of 220 metres. A-PEP has shown that its predictive nature is consistent the workings at both operations, irrespective of their unique conditions, and as such it can be successfully used as a mine planning tool. The A-PEP mine planning tool thus represents a positive step toward an integrated approach to underground coal pillar extraction when considering legal and operational aspects, which could form the basis for legislative guidelines when considering the future of pillar extraction in South Africa.

Jan 1, 2005

Mineral production was of little significance in the country's economy, and Bangladesh was not a world-ranked producer of any mineral commodity during 1977. Natural gas was the most important mineral exploited; however, reserves were sufficient to allow for much greater production, Economically, Bangladesh made some progress in 1977-782 in its struggle against poverty, underdevelopment, and rapidly increasing population. The gross domestic product (GDP) grew 8%, mainly owing to a 13% increase in food grain production, the key economic indicator in this highly agricultural nation. GDP at current prices dropped slightly in Fiscal Year (FY) 1976.77 to $6.6 billion3 and rose to $7.2 billion in FY 1977.78. The population rose from 81 million in FY 1975-76 to about 85 million in FY 1977-78, resulting in an increase of per capita GDP from $83 to $85 during the same period. The high annual population growth rate, over 3% in 1976 and about 2.8% in 1977, was recognized by the Government as the main problem facing the country. Average density was 525 people per square kilometer. A similar density would have the entire world population living within the continental United States.

Jan 1, 1981

By T. Yalcin

In the Box-Wilson method, the correlation between dependent and independent variables is represented by a polynomial response function, whose constant and coefficients are determined by applying regression analysis to the experimental data collected. The five levels used for each variable consist of a minimum, a maximum and three intermediate values. A study was carried out using Ni-Cu ore from Sudbury, Ontario, in which 15 experiments designed according to the Box-Wilson method were carried out in random order and in duplicate. The two sets of replicate data showed close similarity, with an overall variance of 0.311 for the five parameters studied. The response functions were used to optimise frother dosage, collector concentration and air flow rate and an experiment was then carried out under the optimised conditions; the results agreed closely with those predicted by the response functions

Jun 21, 1905

By R G. Barker, A B. Christie

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. More than 11 Moz of Au and 50 Moz of Ag have been produced from epithermal deposits in New Zealand, almost entirely from 50 deposits in the Hauraki goldfield. Since the 1980s, new deposits have been discovered at Waihi (Favona, Trio, Correnso) and nearby at Golden Cross. Feasibility studies into reopening the Talisman mine at Karangahake are continuing, and advanced projects with preliminary inferred resource estimates are reported at Wharekirauponga, Neavesville and Muirs. In the Taupo Volcanic Zone, 11 prospects have been drilled, resulting in the definition of large but low-grade Au-Ag resources at Ohakuri. In Northland, several Au, Ag and/or Hg prospects are known, and small quantities of Ag and Hg have been mined. Six prospects have had some drilling, with the most advanced exploration at Puhipuhi. The application of Taupo Volcanic Zone geothermal systems research to the modelling of former hydrothermal mineralising processes in some epithermal prospects has enabled better targeting of exploration.CITATION:Christie, A B and Barker, R G, 2015. Exploration for epithermal gold deposits in New Zealand, in Proceedings PACRIM 2015 Congress, pp 533–540 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Lower greenschist quartzo-feldspathic schists within the N-S trending Earnslaw Synform of the Upper Wakatipu area are pervaded by late-stage quartz filled extensional and extensional shear fractures, with quartz-scheelite lodes infilling normal faults. Exposed veins/lodes mapped over at least 1000 km2 define a paleoflow system developed during late metamorphic exhumation of the schist. Both veins and lodes have consistent angular relationships to the schist foliation independent of their location on the Earnslaw synform. Unfolding the synform leads to a regional subhorizontal foliation and a systematic set of subvertical quartz veins striking NNW extending over a depth interval >5 km, striking parallel to a set of normal faults hosting the quartz-scheelite lodes. The structures define an extensional regime with s1 sub-vertical, s3 oriented WSW-ENE, a low differential stress, and suprahydrostatic fluid pressures.   The quartz-scheelite lodes (<2 m thick) occupy faults which cross-cut the quartz veins, and are traceable for a few hundred metres, at most. The lodes consist of laminated and/or massive quartz, slivers of crushed and folded schist, random and discontinuous lenses of scheelite with clay selvages separating the lode from relatively undisturbed wallrock schist. Textural evidence suggests that slip developed incrementally with total displacement on faults during lode formation on the order of a few ten's of metres.   The distribution of Glenorchy veins demonstrates broad scale hydrothermal flow through low-permeability schist, channelled within dilatant mesh style structures comprising interconnected shear and extension fractures. Flow through the lodes was likely derived from the greater surrounding area via the interlinked network of fractures and focused into the low displacement shears. Available evidence suggests the system developed together in a uniform extensional stress regime toward the bottom half of the seismogenic regime.

Jan 1, 2001

By J. Kunze, R. Degal

During the last 100 years, the submerged arc furnace has been one of the most amazing diversified melting units. These furnaces have found their application in more than 20 different main industrial areas such as iron, ferro alloy, chemical industry, lead, zinc, copper, refractory, titanium oxide, recycling, phosphorus etc. Such an evolution was only possible because of tremendous efforts in research and development and due to the large range of design solutions. The worldwide strong competition also forced the industry and plant suppliers to develop highly efficient, economically balanced units in optimized sizes and with long lifetimes, to adapt to the market conditions. Regarding the environment, the plants improved significantly in terms of water treatment plants and off-gas treatments as well as on site recycling units. This paper will give a short overview regarding the history of the furnace and the latest developments in today?s main application fields: ferro alloys, non-ferrous, special application and recycling. In addition new activities in research and developments are briefly discussed.

Jan 1, 2004

By Donald O. Capstick

The local geology, the lack of recorded mining activity, and our field investigation and associated sampling indicate a low potential for mineral resources. Claim records and the literature review failed to show any lode or heavy mineral placer mining claim locations that are definitely in the area or anomalous mineral concentrations in the study area. Field investigations revealed no claims, prospects, or mineralized areas.

Jan 1, 1982

By A. Hotta

Reduction of CO2 emissions is the key driving force behind the development and implementation of new solutions for energy production. One solution is circulating fluidized bed (CFB) combustion technology combined with a high-efficiency once-through water-steam cycle. Foster Wheeler's CFB technology is today commercially available in capacities up to 800 MWe with ultra-supercritical steam parameters. Simultaneously, the Flexi-Burn® CFB technology is being developed to provide capability of flexible operation in air firing and oxy-combustion for carbon capture. CFB technology can offer an attractive solution for the reduction of CO2 emissions, owing to advantages such as fuel flexibility and low emissions that the air-fired CFB technology offers today. Pilot test facilities provide information about the performance of CFB oxy-combustion technology, and the acquired knowledge is being incorporated in boiler modelling and design tools. One of the European R&D initiatives on carbon capture and storage (CCS) is the Technological Centre for CO2 Capture and Transport, which is supported by the Spanish Government through the Fundación Ciudad de la Energía (CIUDEN). CIUDEN is a research and development institution created by the Spanish administration in 2006 and fully conceived for collaborative research in CO2 capture, transportation, and storage. The Technology Development Centre for CO2 Capture and Transport comprises two technologies on oxy-combustion: pulverized coal (PC) and circulating fluidized bed (CFB). This paper will focus on the design and main characteristics of the 30 megawatt-hour thermal capacity (MWth) oxy-CFB boiler. Foster Wheeler is the technology provider of the Flexi-Burn CFB unit, for which commissioning has been completed in the first quarter of 2011. The CFB unit design allows operation either under conven¬tional combustion with air or under oxy-fuel conditions. The size of this experimental boiler is sufficient to allow the scaling of the results to commercial units. In this way, multiple fuels and operating conditions can be tested economically. The results will validate the design of a future 330 MWe supercritical Oxy-Combustion Power Station (OXY-CFB-300 Compostilla Project) intended to demonstrate the CCS technology at commercial scale. The Compostilla OXY-CFB-300 Project is one of the six CCS demonstration projects funded under the European Energy Programme for Recovery (EEPR) of the EU. The project is based on a future 330 MWe CFB supercritical oxy-combustion plant, with CO2 storage in a deep geological formation. The first phase of the project, granted by the EEPR programme and led by the Spanish utility ENDESA, includes all studies and characterization work needed on CO2 capture, transport, and storage, as well the costs, financing, and regulatory and permitting required, prior to the final investment decision for the construction phase of the plant by the end of 2012.

Jan 1, 2012

By H. Dong

This paper presents a heat conduction model to determine the erosion profile of freeze linings in a ferronickel submerged arc furnace. Kirchhoff transformation was adopted to simplify the nonlinear equation governing heat conduction. The boundary element method (BEM) and Nelder-Mead simplex optimization method were employed to solve an inverse heat conduction problem. Erosion profiles could be obtained when calculated temperatures at sensor locations agreed well with measured temperatures. The model was validated by comparing the heat loss through the linings, which was calculated by BEM and integral operation after erosion profiles were obtained, with the value calculated from industrial data such as actual power consumption, tap-to-tap time, and ferronickel output. The optimal solution for the erosion profile could be acquired when the difference in heat losses calculated by these two methods is at a minimum.

Jan 1, 2014

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the separation efficiency (E,): E. = (R - R,), where R is the percentage of the valuable constituent and R, the percentage of the waste appearing in the concentrate. The separation efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products. The problem of quantitatively assessing the results of a mineral concentration process recurs whenever one tries to decide which of two similar test results is more desirable. Although economic factors may greatly influence the eventual choice of process, they usually have very little to do with the technical excellence of a separation and are, therefore, not a consideration at this point. Concentrate grade and recovery, used simultaneously are the most widely accepted measures of performance, and if both the grade and the recovery are greater for one case than for another, the choice is simple. However, when the results of closely competitive operations are compared, it often occurs that one set of test results shows a higher grade and a lower recovery than another and the choice is no longer obvious. Laboratory investigations of a mineral concentration process applied to a given feed material can often be designed to yield successive paired values of concentrate grade and recovery over the practical range of the course of a separation process.' These results may be plotted as some combination of the cumulative values of grade, weight recovery, or unit recovery in the concentrate. The resulting correlations for two slightly different sets of conditions can then be compared qualitatively, or even quantitatively in particular cases.2 Such comparisons are not applicable, however, to individual concentration test results. The reduction of a separation test result to a single efficiency figure, preferably as a percentage of ideality, would afford the simplest and most precise means for comparing the results of competitive tests. The effective proportion of feed material that undergoes complete separation in any real concentration process, hereafter referred to as "separation efficiency," is such a figure. It is essily calculated from the usual feed and product data and can even be evaluated, in many cases, from data in publications describing various concentration processes. Mineral Concentration Processes and Their Evaluation Mineral Concentration Processes: The overall concentration process may be subdivided into a liberation process which severs the bonds between unlike mineral species, and a separation process, which sorts the resulting liberated particles into two products—a concentrate rich in mineral A and a tailing lean in mineral A. A perfect mineral concentration process is represented by the idealized scheme shown in Fig. 1 in which liberation and separation are not differentiated. The feed mixture consists of two mineral types which are completely liberated early in the process and then sorted by type. All the mineral particles of type A which respond uniquely to the selection forces acting in the ideal separator, report to the concentrate, while all the mineral particles of type non-A report to the tail-

Jan 1, 1971

By Dale Dean, Bill Hancock, Raul Mondragon, Carlos Aguilar, Chris Martin

"In 1942, commercial mining operations began in what is now the Lucky Friday Ag/Pb/Zn mine in Idaho’s Silver Valley. Wholly owned since 1962 by Hecla Mining Company, the mine has produced more than 145 million ounces of silver and has been a mainstay producer in Idaho’s Silver Valley for over 70 years.However, by the early 21st century, the mill had fallen, technologically, seriously behind the rest of the industry. Accordingly, starting in 2005, the current mill management team set to revitalizing the milling operation. This paper will describe how the mill was systematically evaluated and the aging infrastructure replaced with more current technology. Driven by internal mill review studies supported by QEMSCAN mineralogical balancing, the mill has in recent years been through waves of upgrading – from the installation of new mechanical and column flotation equipment to the introduction of on-stream analysis, a technology well-accepted around most of the industry but alien to this technologically conservative mining district.The experience at Lucky Friday is a testament to the need for ongoing structured mill optimisation and technology upgrading in established mining operations. This paper will describe engineering experiences associated with upgrading equipment in an operating mill, contained in a confined building. Experiences in teaching the team new ways of operating a mill, and finally the metallurgical rewards that have been reaped will be described.INTRODUCTIONMining in Idaho’s Silver ValleyIdaho’s Silver Valley is a 64-km long valley flanked by the US Northern Rocky mountains, seldom more the 3-km wide, and stretching across much of Idaho’s northern panhandle, roughly 150 km south of the Canadian border. Mining has been continuously active in the area for more than 140 years, during which time, the Silver Valley has become one of the richest silver producing districts in the world, and as of 1985 had out-produced the 500 years of production from the famed Potosi district in Bolivia. Since 1885, almost 100 deposits have been discovered and worked in the district (Chapman, 2000)."

Jan 1, 2011

The Bega granite at Whipstick, N.S.W., consists of a granite metasomatically altered to leucogranites and a spessartite-granite. The ore occurs in pipes controlled by jointing and shows evidence of post-depositional tectonic forces.The principal ore minerals are molybdenite and bismuthinite, with minor amounts of uraninite, pyrite, gold, bismuth, joseite A, joseite B, tetradymite, chalcopyrite, arsenopyrite, and skutterudite. The gangue minerals are microcline, albite, quartz, muscovite, and spessartite, with fluorite, chlorite, magnetite, and biotite as accessory minerals.The intrusion of granite was followed initially by ascending metasomatic fluids which penetrated along joints to be trapped in the domed roof of the intrusion to form the leucocratic granite. Iron-manganese-rich fluids metasomatically altered the granite to a spessartitegranite which is associated with the later deposited ore.Quartz veins and dykes of varying composition post date the ore deposition.

Jan 1, 1968

By Ketan H. Trivedi

This paper describes the method of analyses used for the design of temporary and permanent Secant Pile Walls, describes various aspects of construction including, guide walls, sequence of pile installation, plan alignment and verticality tolerance, methods of drilling (auger, wash boring, cased and open holes), lateral bracing for secant piles, cutting of keys in secant pile walls for the connection of permanent floor slabs, sealing of water leaks and waterproofing. The paper concludes with a brief case history of a secant pile wall project recently constructed in New York City.

Jan 1, 2006

By M. A. Trevits, T. A. Gray, L. M. Crayne, P. Glogowski

Mine seals can he remotely constructed in underground coal mines through vertical boreholes when direct access to a fire is impossible or considered to he too dangerous. This method has great merit because the boreholes can be drilled to specific mine areas, and the seals can be positioned close to a fire zone. The technology however can be largely ineffective if the constructed seals do not provide of effective barriers to airflow or if they cannot he used to impound water and other inert materials. Unfortunately, no viable alternatives exists to sealing the entire mine to the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL). Under this effort. Howard Concrete Pumping Company and GAI Consultants Inc. have joined forces to evaluate a potentially significant improvement to the current state of the art. This paper covers the development o f novel technology or rewrote mine seal construction, the evaluation of rite materials used, the construction practice and the Fellow-up testing.

By Charolett Hayes, A. L. Russell, Anthony J. Bednar, Jared Smith, Valentine A. Nzengung, Stephen L. Pilcher

The manufacture of Energetics Materials (EM), including maintenance and demilitarization of munitions causes dangerously high levels of explosives residues to be harbored in building features. The two commonly approved methods of decontaminating energetics contaminated equipment and building features are thermal treatment and steam washing. The current regulatory environment is generally becoming more stringent and unfavorable to thermal and steam decontamination because of their adverse impact on air, soil, and water and their ineffectiveness to completely remove accumulated energetics from foundation cracks, internal and external piping, voids in walls and ventilation systems, and internal cavities of fixed equipment. However, chemical destruction of energetics, especially high explosives, is gaining acceptance as a safer, cost-effective and environmental friendly alternative to thermal and steam decontamination. Organic explosives, including nitramines and nitrate esters are oxidized organic compounds that are susceptible to chemical oxidation and reduction reactions. Under suitable conditions, a chemical reagent consisting of sulfur-based bulk reductants (neutralent) commercialized as MuniRem generates highly reactive free radicals that very rapidly degrade many energetic compounds to innocuous end products while stabilizing metals as the insoluble metal sulfides.

Jan 1, 2016

Owing to the number of chemical processes now in use for the separation of metals from their ores, and the consequent employment of chemicals at the mine, it is sometimes necessary to be able to produce them on the spot. This particularlyapplies to sulphuric acid which may be required for the manufacture of chlorine and of sulphate of copper, or for the treatment of'sulphides and other purposes. It can be made from brimstone for rather less than £3 per ton, but when delivered to any distance from the works, the cost of packages and other charges would amount to more than the value of the acid.I hope therefore, that to any of the members of the Institute who may find it necessary to make sulphuric acid for their own requirements an outline of the process, and some details of the plant etc may be useful, and perhaps lead to their devising improvements, mechanical or otherwise. Though acid can be made from pyrites in Europe for about 15/- per ton, it is probable that for most metaIIurgical purposes the quantity required. and the uncertainty as to how long it would be needed, would make it advisable to spend as little as possible on plant, and so use brimstone, though more expensive, I have therefore given no details of pyrites burning, which is very fully treated by Prof, Lunge in his work on " Sulphuric Acid and Alkali."

Open cut mining of the Black Rock chalcocite ore started in 1963. A ground movement monitoring programme was commencing in the early stages of mining when signs of instabilityof the western wall became apparent. Eventually 100.000 cu vd, of overburden Were removed beyond the rim of the western wall in an attempt to stabilize the slope. Subsequent decpenlug and mining till the final batter angle of 45 resulted in deterioration and mining was stopped 38 ft short in the ulltimte design deplh of 520 ft.Investigations showed that the geology of the western wall , was a major factor in the instability of this wall. A block jointed model was made 10 illustrate some of the pehomena observed. Quallatative agreement was found between the model deformation and the field measurements obtained.The results of the monitoring programme clearly show the value of this work In respect to the conlrol of the mining operatIon...

Jan 1, 1968

By R. M. Tyler

The importance of the heavy mineral sands to southern African economic well-being cannot be over emphasized. The value of the worldwide titanium dioxide industry is estimated at $7 billion. Six out of eight of the world?s proposed new project areas are in southern and eastern Africa, and a seventh at Tamil Nadu in India is partly owned by a South African company, Kumba Resources. The HMS industry can be highly lucrative; its return on capital is the best in the mining industry. There are, however, problems, particularly in the smelting technology. The often considerable affect of mining on environmentally sensitive coastal dunes is also becoming increasingly important. The medium-to long-term demand for Ti-dioxide pigment and ceramic grade zircon appears very healthy. If, as predicted, the costs of producing titanium metal can be reduced, then there is huge potential for the metal. In summary, the HMS industry is an attractive one to be in, with good returns and generally manageable risks. New business opportunities and their economic implications for Africa are discussed.

Jan 1, 2004

By John Popovich

The MICON RokLok binder system including component and consolidation processes and safety and its first aide are described. The implementation procedures and selection of injection parameters are discussed. Finally a case example of recovering a 30-ft. long roof fall in mainline haulage entry is used to illustrate the economic potential of preventive measures by RokLok injection.

Jan 1, 2001

By C. Özgen Karacan

Gob gas ventholes (GGV) are used to control methane inflows into a longwall operation by capturing it within the overlying fractured strata before it enters the work environment. Thus, it is important to understand the effects of various factors, such as drilling parameters, location of borehole, applied vacuum by exhausters and mining/panel parameters in order to be able to evaluate the performance of GGVs and to predict their effectiveness in controlling methane emissions. However, a practical model for this purpose currently does not exist. In this paper, we analyzed the total gas flow rates and methane percentages from 10 GGVs located on three adjacent panels operated in Pittsburgh coalbed in Southwestern Pennsylvania section of Northern Appalachian basin. The ventholes were drilled from different surface elevations and were located at varying distances from the start-up ends of the panels and from the tailgate entries. Exhauster pressures, casing diameters, location of longwall face and mining rates and production data were also recorded. These data were incorporated into a multilayer-perceptron (MLP) type artificial neural network (ANN) to model venthole production. The results showed that the two-hidden layer model predicted total production and the methane content of the GGVs with more than 90% accuracy. The ANN model was further used to conduct sensitivity analyses about the mean of the input variables to determine the effect of each input variable on the predicted production performance of GGVs.

Jan 1, 2009