Search Documents

The commercial application of electrolysis to zinc sulphate solutions for the production of metallic zinc is a development ·of the past twenty years. Earlier attempts failed to give satisfactory results, chiefly because certain harmful elements were either not recognised as being present in the solution, or, if recognised, suitable methods of removal had not been developed. The electrodeposition of zinc from zinc sulphate solution is extremely sensitive to the influence of a great many factors, all of which appear to be closely inter-related.Some of these factors tend to minimise the necessity for a high degree of purity of the solution, while other factors aggravate the harmful nature of certain impurities.The relationship existing betweBn the various factors in zinc electrolysis makes a general discussion of the injurious effect of impurities very difficult since, under one set of conditions a given concentration of an impurity may be of minor: importance, where its under another set of conditions the same concentration of that impurity may prove dangerous to successful electrolysis.

Jan 1, 1934

Over half of the molten aluminium produced at the 52,000 tons/ year eapacity plant operated by Comalco Aluminium (Bell Bay) Limited in Tasmania is cast into saleable produets by the direct chill process. Considering the importance of direct chill casting to the aluminium industry it is surprising that so little published literature on the subject is available, although Easton (1947), Smart (1954), and Uppert (1940, 1944, 1945) have contributed much toward lifting the veil of secrecy surrounding the process.The direct chill, or D.C. process as it is commonly called when related to aluminium, consists basically of feeding molten aluminium or its alloys into; water-cooled mould from the bottom of which solid aluminium is continuously extracted. Although the casting procedure is continuous in principle, the equipment is normally operated in an intermittent manner. Castings up to 20 ft long are formed during a cycle. At the end of the cycle casting is stopped and the pit into which thc castings are dropped is cleared before a new cycle commences. Depending on the size of the casting in relation to the cross sectional area of the pit and the support mechanism (commonly a hydraulic ram), 'drops' of up to 15 tons are not uncommon. This method of D.C. casting IS termed vertical D.C. casting and is the one most commonly employed in the aluminium industry.Horizontal casting has come more to the fore in recent years with the casting being extracted from the mould in the horizontal plane and is a truly continuous casting method since flying saws can be simply used to cut the continuously cast shape into required lengths as it emerges from the mould...

Jan 1, 1967

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

In preparing a paper such as this it was thought that the Newstan Colliery Company Ltd., being comparatively new, would need some introduction to mining people in general.The Newstan Company was formed by the Joint Coal Board in December, 1948 during a period of acute coal shortages. The Company took over the holdings of what were known as the Olstan and Northumberland Collieries, situated at Fassifern, alongside Lake Macquarie and adjacent to the Great Northern Railway, within easy rail access of Sydney and Newcastle, as shown on the locality plan (Fig. 1).The Company was developed in order to produce steaming coal for the power house trade and has continued its activities in the steaming coal trade since its inception. The Olstan and Northumberland collieries were together producing some 300 tons per day when the Company was formed, and it was from this foundation that the colliery was built. The planned development of the Company has been along the lines of producing coal by modern, highly mechanised methods, together with the preparation of theproduct for the consumer, to the highest degree possible consistent with up to date methods.In the comparatively short time of 5t years the mine has developed from a small hand-won coal unit to a high capacity modern mine, one of Australia's largest producers, with an output capacity as high as 3,000 tons per shift.

Jan 1, 1954

By Turner WG, Short RR

Obviously, the paramount advantages of contract mining have been recognised by mine developers throughout Australia, as evidenced by surface gold mining operations of significant output almost exclusively being performed under contract. These paramount advantages of using an experienced professionally managed contractor result from the mine developer being freed from financing the required relatively large capital expenditure at current relatively high interest rates or in a capital scarce stock market, and from the need to recruit and sustain a large operating work force in a competitive labour market.

Jan 1, 1990

By C. Machio

This paper reports the results of a study to determine the effect of process control agent (PCA) on the characteristics of Ti-Mg powders during milling. It has been shown that a 2% increase in PCA content leads to up to a 40% increase in yield of the milled powder but reduces the kinetics of the mechanical alloying process. The introduction of 4% PCA decreases the mean powder particle size by up to 30%, whereas 6% PCA increases the mean particle size by up to 230%. The characteristics of the milled powders will be discussed in relation to the role of PCA in the milling process. Keywords Titanium?magnesium, mechanical alloying, PCA.

Jan 1, 2011

By Don Thompson

It isn?t a lie if you don?t tell the whole truth The pictures National Geographic didn?t print Other photos National Geographic didn?t print?

May 1, 2009

The rocks of Waihi and the surrounding district are almost entirely rhyolitic and ande5itic in character. Sedimentary rocks, with the exception of some surface deposits of clay loosely compacted conglomerate, etc., and one or two thin and broken beds of a very poor lignite, occasionally changed by igneous agencies into a bituminous coal, are almost absent. In the shafts sunk by the Waihi and Grand Junction companies outside the outcropping andesitic area of the Martha Hill, more than one old surface or lake bottom has been passed through. At these points layers of sand, consolidated volcanic mud and tuff, accompanied by numerous broken fragments of imperfectly silicified wood have been enccuntered, but these occurrences may, for the purpose of this paper, be neglected.The youngest rock of the district are rhyolites, probably of Pliocene age. At least three distinct classes of rhyolitic lava, each possessing features of unusual interest, may be made out. None of these, however, is gold-bearing. The youngest flow, a light-coloured, fine-grained rock, is remarkable owing to its enclosing at times fragments of carbonised wood, varying in size from mere specks up to quite large pieces of almost pure charcoal. Rhyolitic tuff is also met with. The rhyolites cover a large extent of nearly flat country east, south, and west of Waibi, here and there rising into barren, stony hills.Below the rhyolites, geologically speaking, but for the most part. forming hills which bound the rhyolitic plain, or rise out of it as isolated patches, come ahdesites of older...

Jan 1, 1902

It is easy to demonstrate the importance of aggregates in any conversation about infrastructure and other engineering artefacts. Peoples around the world have made use of stone to enrich and enhance their lives since the earliest days of civilisation. In New Zealand, Maori used hard durable rocks for weapons, tools, and basic structures. European settlement accelerated the use of quarried materials and formed the basis for development of our society as we see it today. Logic might suggest that the quarrying sector would be recognised positively for, and encouraged to continue to contribute to, this underpinning of the way we are. The reality is æNot In Most Back YardsÆ. Why? The rock is where it's always been (often overlooked) and our æsocialÆ environment is today's hard place. For a resource-based business in New Zealand, that environment is principally the Resource Management Act, with the widespread power it has distributed to anyone prepared to invest their time. This coupled with a lack of leadership and direction in the implementation of the Act has created a climate that stifles development and diverts energy and resources to æplaying the gameÆ rather than ælifting the gameÆ. Perhaps the real costs of this are not yet widely recognised. The paper will draw mainly on the experience of endeavouring to consent a ægreenfieldÆ quarry in the Waikato region. This is supported by commentary based on nearly 10 years of ælivingÆ with the RMA at sites across much of New Zealand. RMA Scorecard Summary: Effects based? Rarely. Level playing field? No. Maori Consultation? Could do better. Efficient use of resources? No. Timely? No. Is it working for other sectors? Certainly not the quarrying industry's customers and end users.

Jan 1, 2000

By Vincent A. Scovazzo

Many accepted and useful methods have been developed and used for pillar design. Each method has its own particular strengths and weaknesses. Three methods addressed in this paper are; empirical, analytical, and numerical. Each of these methods have their place in pillar design. Analytical methods result in close approximation of the ideal pillar (most economical, stable, or yielding) and are suitable for use in final mine design and in analyzing existing problems. BOYD uses the analytical method to develop site specific mine pillars design equations. An analytical method, one of many developed by BOYD, is presented here and is based on the procedure used by Wilson (1) and others in development of their empirical equations.

Jan 1, 1995

By H. Gumede

The occurrence of fracturing due to high stress levels is a major factor in hangingwall stability in deep level gold mine stopes. However, rock falls cannot be the result of these fractures alone. Rock falls can result only from the occurrence of unstable rock blocks defined by the interaction of the stress induced fractures and naturally occurring geological planes of weakness. These planes include bedding planes and joint set planes. However, there is a general lack of information on the characteristics of these planes (orientations, spacings and lengths)?it does not appear that any such systematic and quantified information, if collected, has been published. To remedy this situation to some extent, joint mapping exercises have been carried out in several geological environments in two gold mines. The data collected on joint geometry included orientation, spacing and length, and this information is included in the paper. In addition, the paper describes the use of the data collected to evaluate the potential for rock falls and the probability of failure of stope support

Jan 1, 2007

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

By Donald A. Bruce

"Abstract The Deep Mixing Methods (DMM), in their current forms, have been employed in the United States since 1986, although an earlier version had seen service from 1954. The earlier developments were strongly influenced by practices in the Nordic countries and Japan, while by the late 1980’s several DMM systems had been developed in the U.S. itself. Since then, DMM has continued its evolution, principally via the challenges of a series of large, landmark projects, but also via distinct, significant technological advances. This paper highlights the key points in the history of DMM in the U.S., and provides an overview of the different methods currently in use.In the BeginningIt is a common misconception that the history of applications of the Deep Mixing Methods (DMM) in the United States dates from 1986 when SMW Seiko Inc. — a subsidiary of Japan’s Seiko Kogyo Company — was established in the Bay Area. However, the author believes that Intrusion Prepakt Co.’s patented MIP (Mixed in Place) system had been used, albeit sporadically (about 30 projects are recorded), since 1954 (FHWA 2000, 2001). Ironically, by 1961 this single auger method had been extensively used under license in Japan for excavation support and groundwater control — by the Seiko Kogyo Company. By 1972, the original MIP technique had been succeeded by more advanced Japanese methods, involving multiple augers. Intrusion Prepakt have long since become defunct.The first systematic studies of contemporary Deep Mixing Methods in Japan began in 1967 when the Port and Harbor Research Institute of the Ministry of Transportation began laboratory testing using granular and powdered lime for treating soft marine soils. Fundamental studies continued through the early 1970’s, by which time the development of industrial scale equipment was well advanced, having its first application on a marine trial near Haneda Airport. Coincidentally, laboratory and field research also began in 1967 in Sweden (“Swedish Lime Column Method”) for treating soft clays using unslaked lime. Reportedly the progenitor was a Norwegian, Kjeld Paus, who had made observations on fluid lime columns in the U.S. It would seem that developments in Japan and the Nordic countries proceeded independently until 1975 when the technology leaders from each group (Broms and Boman; and Okumura and Terashi, respectively) presented their — very similar — findings at a conference in Bangalore, India. Limited technical exchanges ensued thereafter.Whereas the Nordic developments continued to focus on the use of dry reagents (cement and lime) and relatively light equipment compatible with operating on and in very soft clays and organics, the Japanese progressed into the use of fluid reagents (cement-based grouts) and heavier equipment for both marine and land-based projects. Thus, by 1986, there were a large number of proprietary (wet and dry) DMM systems in Japan, and a rapidly growing market already by then accounting for over 12,000,000 m3 of ground treatment."

Jan 1, 2014

IN presenting a'description of milling and treatment methods at the Waihi mine, it is advisable to first traverse a good deal of the past history of the mine, and show the various steps which have led up to present-day practice. The record of the company is one of steady, solid advancement, both in metallurgical and financial results. This is illustrated by the following figures, dating back from 1897...

Jan 1, 1912

By Zhouhua Jinag

The attempt has been made to manufacture high nitrogen austenitic stainless steels by pressurized electro-slag remelting furnace with maximum nitrogen pressure of 7MPa. To obtain high nitrogen content in steels, the compound electrodes with different nitrogen sources (FeCrN, Si3N4) were prepared. Using the Si3N4 as the nitrogen alloying source, the silicon contents in ingots were prone to be out of the specification range, and the electric current fluctuated greatly and the surface qualities of the ingots were poor. The surface qualities of the ingots were improved using FeCrN as nitrogen alloying source. The sound and compact macrostructure ingot with the maximum nitrogen above 1.0wt% could be obtained. A series of high nitrogen austenitic stainless steels have been successfully developed by this method. The mechanical and pitting corrosion resistance properties of high nitrogen austenitic stainless steels were investigated. The results show that the steels exhibit excellent mechanical and pitting corrosion resistance properties.

Jan 1, 2009

By R. T. Jones

Base metals and platinum group metals can be collected in metallic alloy form, via a wide variety of smelting processes. The recovery, or degree of collection, of the valuable metals is a function of the extent of reduction in the furnace, which, in turn, is indicated by the fraction of iron present in the feed materials that report to the alloy. An equation has been developed that relates the recovery of various metals (such as Ni, Co, Cr, and PGMs) to the recovery of Fe. This recovery equation (for each metal) is characterized by a single parameter (K?) that can either be empirically fitted to the data, or expressed in terms of the equilibrium constant and the ratios of the activity coefficients involved. Data from a number of varied DC arc furnace campaigns are presented to illustrate this behaviour.

Jan 1, 2009

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt. Under the scope of the study, which has been performed to determine the effects of the artificial discontinuities at different depths and the effects of artificial discontinuities through structural damage risk, three test areas, at the same location and same formation, were considered. Six numbers of artificial discontinuities, each 10 m (32, 81 ft) transverse, were created by using pre-splitting and drilling-blasting technology. The number of sequential artificial discontinuities on each test area is two and they have the same length. The length of artificial discontinuities are; 6,80 m (22,31 ft) at the first test area, 13,60 m (44,62 ft) at the second test area and 17,00 m (55,77 ft) at the third test area respectively. The distance between sequential artificial discontinuities is 8 m (26,25ft) on each test area. Thirty-one shots were executed in order to produce vibration (10 shots on the first test area, 11 shots on the second area, 10 shots on the third test area). One hundred and twenty-three seismic recordings were obtained during the execution of the shots by using 4 seismographs. The closest distance between the shot points and the nearest measuring station is 5,30 m (17,39 ft). During the shots, the rock was cracked and there was no fragmentation and/or fly rock. At the first test area, measured PPV values are between 25,40-127,00 mm/s (1-5 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. At the second test area, measured PPV values are between 76,20-177,80 mm/s (3-7 inch/s) before the first artificial discontinuity and less than 76,20 mm/s (3 inch/s) after the second artificial discontinuity. At the third test area, measured PPV values are between 50,80-279,40 mm/s (2-11 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. Peak reduction rates in Peak Particle Velocity (PPV) values determined by measuring as follows: In the first test area 95,77% (106,00 mm/s to 4,48 mm/s) (4,17 in/s to 0,18 in/s), in the second test area 79,77% (176,00 mm/s to 35,60 mm/s) (6,93 in/s to 1,40 in/s), in the third test area 95,85% (from 205,00 mm/s to 8,55 mm/s) (from 8,07 in/s to 0,34 in/s). The arithmetic mean of the differences of PPV values (decrease rate) is 82,66% in the first test area, 69,37% in the second test area, and 92,03% in the third test area. The highest sound value is 138,50 dB and is defined as “noise”. When the measured parameter values are examined it was determined on the USBM norm graphs that these vibrations carry a risk of structural damage in the region before the first artificial discontinuity. While passing through artificial discontinuities the vibrations progress by losing energy and the vibrations passing through two artificial discontinuities do not carry structural damage risk under current conditions.

By Danell. R. E.

A drill monitoring system has been developed which measures performance characteristics of a rotary drill and relates this to the material strength and rotary specific energy. The drill monitor is computer based and is used to produce a profile of the relative in-situ material strength as a function of depth. This information has been used in determining the placement of explosive in selective loading of blastholes and estimating the amount of lump product in a particular section of an ore body.

Jan 1, 1989

By A. K. Tripathy, P. K. Pattnayak, H. S. Ray

The effects of water addition on the solid-state reaction between Cr2O3 and Na2CO3 at low temperatures (up to 873 K) were investigated to determine its possible influence on the reaction rate and the degree of conversion to soluble chromate. Experiments at high temperatures were conducted for comparison. It was found that adding water to the mixture before roasting enhanced both reaction rate and yield significantly. The reactions followed the Lesokhin-Tempelman equation at low temperature and the Ginstling-Brounshtein equation at above 973 K; the respective activation energies were 95 and 22 kJ/mol

Jun 19, 1905

By Steve Kral

Despite low commodity prices and mining industry cutbacks throughout the world, Peru remains one of the industry’s bright spots. The country’s remarkable economic turnaround during the 1990s remains a model for other developing nations to follow. And the Peruvian government has not forgotten the industry that was instrumental in that turnaround. True, the country has not been spared the effects of the mining industry’s retrenchment that has occurred in other parts of the world. However, foreign mining companies remain committed to doing business in Peru. And the government remains committed to attracting foreign investment and maintaining a strong mining industry. This commitment was evident in September 1999during the 24th Convention of the Institutos de Ingenieros de Minas del Peru in Arequipa, Peru. More than 3,000 mining industry professionals from around the world attended the convention. And Extemin, the accompanying exhibit, featured more than 450 companies, many from the United States, Canada, Australia, South Africa and other countries.

Jan 1, 2000