Search Documents

By R. G. Kidel, S. C. Doming

The project has shown that it is feasible for a junior company to reopen a narrow vein-style gold mine and successfully take it into production. An intimate understanding of the mineralisation and a flexible approach to mining are crucial, as are stringent cost control and efforts to keep overheads low. The project has confirmed the geological complexity of the Main Lodes, which consist of highly sheared quartz-sulphide infill in strongly sericitised granodiorite. The existence of discrete high-grade zones within the Hangingwall Lodes has also been confirmed. Broad low-grade zones continue to be recognised and require the local application of bulk longhole mining methods. The initial mine plan called for predominantly longhole stoping, but adverse ground conditions have meant that a switch to air-leg mining has produced higher run-of-mine grades. The excess capacity at the processing plant can best be used by batch processing, with its reduced maintenance requirements

Jun 21, 1905

By H. G. Wolfhard

The propagation of explosions through short cylindrical channels has been investigated by the Bureau of Mines. In the experimental apparatus set up by the Bureau, a single such channel formed a connection between a small explosion vessel in which a gaseous explosion was initiated and a larger, partly enclosing, explosion vessel filled with suitable gaseous mixtures; the larger vessel permitted observation to determine if an explosion was induced therein by mass, energy, and species transfer through the channel, as a result of tie initial explosion, It has been found that transmission of flame through to channel is not an essential to induce the second explosion, for hot gases from an extinguished explosion are able to ignite cold combustible mixtures in the larger vessel. The schlieren patterns of flames or hot burned gases emerging from a channel into the explosion chamber were photographed. These show, in most instances, that vortexes of hot gas ejected from the jet into the cold explosive mixture are responsible for ignition. The study has practical significance in problems of rendering electrical equipment safe for use in potentially flammable atmospheres, INTRODUCTION The propagation of flames through cylindrical or annular channels has practical importance in flameproofing electrical equipment and for flame traps. Much practical work has been done to determine the minimum safe breadth of flanges and the maximum safe gap between the flanges that will permit venting an electric motor without allowing flames to pass.

Jan 1, 1959

By M. G. Zabetakis

This publication contains highlights of a 4-hour lecture and demonstration by the Bureau of Mines on the fire and explosion hazards of flammable liquids and solids, oxidizing materials, corrosive liquids, and compressed gases. The authors first presented this material as part of a 2-week course given to officers and enlisted men at the U.S. Coast Guard's Dangerous-Cargo Handling School, established at Fort Eustis, Va., in 1959. The Bureau was asked to present the lecture and demonstration because of the extensive experience of its researchers in handling certain harardous commodities.

Jan 1, 1961

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By J. Mitchell Linnet

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of deposits in the Bucks Lake and Chips Creek RARE II areas in Plumas and Butte Counties, California. These areas lie along the west slope of the Sierra Nevada on opposite sides of the North Fork Feather River and encompass an area of 62,800 acres (25,400 ha). Metasedimentary and metavolcanic rocks of the Pennsylvanian Calaveras Formation are intruded by plutons of Mesozoic age. Mineral; of economic iterest are in quartz veins in metasediments close to these plutons; they are principally gold and silver with minor amounts of copper, lead, and zinc minerals. Molybdenum, copper, silver, and tungsten minerals occur in tactite along metasedimentary-granitic rock contacts. In both areas, auriferous Tertiary channel gravels have been extensively developed. Asbestos occurs in ultramafic rocks in both areas, and a limestone deposit was explored in the Chips Creek area. Gold is the principal economic mineral in the Bucks Lake RARE II area. The Shenandoah Mine (fig. 1, no. 19) contains 7,500 tons (6,800 t) of indicated and inferred subeconomic gold resources in sulfide-bearing, silicified metamorphic rocks of the Calaveras Formation (table 1). Similar rocks have yielded gold at the Edman and Megowen Mines, adjacent to the area. A high potential exists for additional lode resources in the area around the Shenandoah Mine. Callahan Mining Corporation personnel believe a multi-million ton disseminated gold deposit underlies the property.

Jan 1, 1983

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from, the underlying unoxidized ore through prolonged weathering. The degree of oxidation in different sections and at different depths within the bed is nut. uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By Nicolas Denies, Gust Van Lysebetten, Bart Lameire, Jan Maertens, André Vervoort, Noël Huybrechts, Flor De Cock

"Abstract Originally developed for ground improvement works, the deep mixing method (DMM) has increasingly been applied in recent years for the realization of soil and water retaining structures and as alternative to traditional foundation solutions. From practice, there is a real need for practical guidelines dealing with the execution, the design and the control of such applications. With the aim of developing such guidelines, the BBRI ‘Soil Mix’ project was initiated in 2009. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites has been tested. In spite of the large advances in the mechanical characterization of the DSM material, one major issue remains the representativeness of the typical core samples in comparison with the real scale behavior of the soil mix elements. There is among others the question of the influence of the unmixed soft soil inclusions on this behavior and the issue of the scale effect which must be considered in the design. In order to investigate these questions, 8 large scale UCS tests and 17 large scale bending tests have been performed on excavated soil mix elements. The present paper discusses results of this experimental campaign, presents some research perspectives and highlights different aspects related to the design of soil mix elements for the realization of retaining wall or foundation solution.INTRODUCTIONSince several decennia, the deep mixing method (DMM) has been used to improve the strength and deformation characteristics of weak soils. In recent years, deep mixing has increasingly been applied – in Belgium and in other countries – for the realization of soil and water retaining structures and alternative foundation concepts. With regard to the execution of the DMM, one can refer to the European standard EN 14679 on deep mixing (2005) that was elaborated under the umbrella of CEN TC 288 “Execution of special geotechnical works”. However, from practice, it has been experienced that this execution standard does not provide enough pragmatic information and guidelines, in particular for the more recent applications of the deep mixing method (with retaining and bearing functions). The same need by the sector for guidance rules linked to design aspects in the context of Eurocode 7 was experienced as well. With the aim of developing such guidelines and in order to provide feedback to the European standardization platforms, the Belgian Building Research Institute (BBRI) has initiated the BBRI ‘Soil Mix’ project (2009-2013) in collaboration with the KU Leuven and the Belgian Association of Foundation Contractors (ABEF), the Belgian branch of the EFFC. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites, with various soil conditions and for different execution processes (CVR C-mix®, TSM and CSM), has been tested (Denies et al., 2012)."

Jan 1, 2014

By E. A. Mihok

A pilot plant for treating mine drainage by neutralization with limestone was designed, fabricated, and operated by the Bureau of Mines. The process consists of (1) producing a very fine (minus 400-mesh) limestone slurry, (2) mixing the slurry with the mine water, (3) aerating the resulting mixture to remove carbon dioxide and precipitate iron, and (4) separating the solids from the liquid by sedimentation. A mine discharge of pH 2.8, containing 1,700 ppm total acidity, 36 ppm ferrous iron, and 360 ppm total iron, was treated at rates from 300 to 400 gpm. The treated water ultimately reached a pH of 7.4 and contained no detectable iron. The resulting sludge compacted to approximately one-third the volume of sludge from mine water neutralized with lime. The advantages of the limestone process, compared with the conventional lime process are as follows: Widespread distribution and lower cost of run-of-mine, indigenous limestone; simplicity of plant design; reduced hazards and plant operating and maintenance costs accruing from the use of a less reactive chemical agent; higher solids concentration of the precipitated sludge; and no deleterious effect caused by accidental overtreatment. While total process costs could not be determined, it is conservatively estimated that the cost of treating mine water by the limestone process is one-third to one-half the cost of the lime process, depending on the characteristics of the water to be treated and the availability and quality of limestone used.

Jan 1, 1968

By P. J. Remington

Field measurements utilizing a seat pad accelerometer were made on 25 underground coal mining machines in order to quantify the vibration levels experienced by the operators. Those data were combined with information on the statistics of the operating times of those machines in order to compare the operator's vibration exposure to the criteria in ISO 2631, "A Guide for the Evaluation of Human Exposure to Whole Body vibration." The comparison showed that about 30% to 40" of all underground coal mining machine operators can be expected to be exposed to vibration exceeding the fatigue decreased proficiency criterion, whereas only 10 to 15% would be expected to experience vibration exceeding the exposure limit. The primary sources of the exposure are shuttle cars and possibly scoop trams. Detailed exposure statistics are presented and the implications of the results are discussed.

Jan 1, 1983

By Nicholas R. Dixon

This report summarizes all work performed under Phases I, II and III of U.S. Bureau of Mines Contract H0387006, "Development of a Prototype Retrofit Noise Control Treatment for Jumbo Drills." The noise and vibration levels of four jumbo drills were characterized and a survey of percussive rock drill usage is reported. A Gardner-Denver DH 123 drill was chosen as a demonstration drill, and extensive noise diagnostic studies were performed. Noise control treatments were designed, developed and evaluated in a reverberant drill test facility. The treatments consisted of an integral enclosure/muffler for the drifter, vibration isolation of the drifter from the enclosure and feed, and a drill steel sheath. A 19 dBA reduction in overall sound power level was achieved with no loss in drilling rate. The prototype retrofit treatments were field tested in an aboveground mine and in a production section of an underground zinc mine. Long-term durability and operator acceptance of the enclosure/muffler treatment were excellent. Preliminary evaluation of the drill steel sheath was encouraging, although additional testing is required.

Jan 1, 1982

By Paul Meadows

This Bureau of Mines report presents operating practices and results of pressure maintenance and secondary recovery by water injection or by water injection supplemented by gas injection. Particular emphasis is placed on the results of water injection, which is the principal oil-recovery method employed in projects covered by this report. No attempt is made to study gas-injection projects or operations that are considered water-disposal projects. Also, this report does not include water-injection projects that have not been in operation long enough to evaluate results. Figure 1 is a map of north Louisiana showing the geographical locations of the projects included in this report. Most of the data used in this study were supplied by unit operators, operating companies, and the Louisiana Department of Conservation. Reservoir information and recovery data are generally those supplied by the operators, but include revisions where deemed necessary.

Jan 1, 1962

By H. A. Wright

This report assesses the economic, legal, institutional and technical factors that affect the current and future status of implementation of mine monitoring systems in the United States. It begins with a description of a poll of the Mining Production Research Committee and the Mine Monitoring and Communications Committee of Bituminous Coal Research that was conducted to establish industry monitoring needs and constraints. Existing systems in the United States and foreign countries are then reviewed and compared with the requirements set forth by the industry committees. At the same time, state and federal mining laws are reviewed, and equipment currently available from suppliers of mine monitoring systems and components is discussed. A framework for cost/benefit analysis is established and a series of case examples for various monitoring functions are presented. The total values of the market for mine monitoring systems in 1980 and 1990 are estimated on the basis of industry statistics and system cost estimates.

Jan 1, 1982

By P. J. Watson

The objective of this study was to prioritize the potential risks nuisance and biologically active dusts and fumes present in metal and nonmetal mines. This was accomplished by ranking numerical values derived from a matrix formula calculation that took into account dose, mine population, and sampling size. Data used in these calculations were obtained from the Mine Inspection Data Analysis System (MIDAS). The dusts determined to have the highest risk potential were quartz respirable particulates, mine dust, cristobalite respirable particulates, welding fume components, and nuisance respirable dust. Other dusts and fumes that were not ranked in this study, due to small sampling population, but which show a potential risk, include asbestos, talc, hydrogen cyanide, organic compound dusts, arsenic, metal dusts, and metal and nonmetal fumes.

Jan 1, 1987

By Clyde L. Brown

The ignition source of fires and explosions in coal mines is sometimes difficult to explain because resulting widespread destruction often erases valuable evidence that might reveal the cause. However, through years of experience, investigators have been able to piece together enough evidence to establish the reasons and, thereby, have been equipped to recommend corrective or preventative measures. The pattern of hazards is not constant. It changes with the development of new practices and new equipment. Important among the new hazards to coal mining are those introduced by electricity. In addition to the dangers of electric shock, fires and explosions from heat and arcs, and premature blasts, certain others have developed as a result of stray electric currents from direct-current traction systems. The conventional direct-current power-distribution system in coal mines is conducive to electrolysis damage to mine tracks, metallic pipelines, grounded power conductors, and structures in a position to become conductors of stray currents. The voltage drop resulting from power demand on intentionally grounded power conductors and accidental grounds on insulated conductors are common sources of stray currents in coal mines. Uncontrolled electric cur-rents flowing through the earth and metallic structures can be a menace, and these contribute to the estimated $6,000,000,000 annual loss caused by corrosion. The purpose of this publication is to discuss some of the electrolysis hazards in the coal-mining industry and to outline corrective measures to alleviate them.

Jan 1, 1962

By W. W. Adams

"The seventh National Safety Competition, that for 1931, conducted by the United States Bureau of Mines, was participated in by 350 mines and quarries operating in 34 States. Tables 1 to 5 show the relative standing of the various plants, Bronze trophies, known as the ""Sentinels of Safety,"" which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines were awarded to five companies, each company having established the best accident—prevention record within one of the five classes into which all companies were divided — namely, anthracite mining companies, bituminous—coal mining companies, metal—mining companies, operators of nonmetallic mineral mines other than coal mines, and quarries or open—cut mines. The trophies are awarded for one year and are then transferred to the winners of the succeeding year's contest.The outstanding feature of the contest of 1931 was the operation of a bituminous coal mine without a lost—time injury to any employee. While accident—tree records had previously been made by certain quarries, metal mines, and nonmetallic mineral mines, never before has such a feat been accomplished by a bituminous coal mine in the National Safety Competition. Whether or not such a record has been made by a bituminous—coal mining company not enrolled is the competition the writer does not know, but it is believed that the case referred to is unique among large coal—mining companies. The mine to which reference is made is No. 1 mine of the Phelps Dodge Corporation, at Dawson, N. Mex. To that company belongs the distinction not only of being the first coal—mining company among those enrolled in these yearly safety contents to operate its mine without an accident but also of occasioning the 'Sentinels of Safety' trophy for a bituminous mine to take its first journey west of the Mississippi River. For the past six years the trophy has been in West Virginia, Alabama, or Pennsylvania."

Jun 1, 1932

By R. T. Stain

Integrity testing of deep foundations is now common practice in Europe, indeed in the City of London such testing is a contractural requirement on every site. This paper is in two parts: Part 1 describes the most commonly used test methods and their applications. Part 2 presents a case history where both of the above techniques were used.

Jan 1, 1987

By Richard E. Thill

Elastic wave velocities and moduli were determined by both the pulse and resonance methods in a large number of specimens of St. Cloud Gray Granodiorite and Tennessee marble under the same moisture, temperature, and stress environment. Long cylinders were first tested by the resonance method to obtain longitudinal bar and torsional wave velocity. The cylinders were then sectioned in half and tested by the pulse method to obtain the transient pulse velocity. These velocities were later used to obtain various moduli for comparison. Statistical comparisons between the Young's, shear, and bulk moduli and Poisson's ratios obtained independently by the pulse and resonance methods indicate that the methods do not give equivalent results in nearly isotropic rock. The amount of difference varies for each modulus, with the least difference (less than 5 pct) occurring in the shear modulus and the greatest difference (as high as 34 pct) in the bulk modulus. Moduli determinations in aluminum show much closer agreement between the pulse and resonance methods than in rock. The discrepancy in pulse and resonance results probably is caused by frequency dispersion effects and by differences in error sensitivity in the various formulas used to calculate the moduli.

Jan 1, 1974

By Andrew M. Leszcykowski

This report represents the first comprehensive accounting of lode mining sites in the Sheep Mountain mining district, Custer County, Idaho. Twenty-one mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were checked and the updated information added to the data base. The district's deposits are mainly confined to metasedimentary xenoliths in granodiorite and quartz monzonite. Those deposits in the north and west parts of the district are lead-silver-zinc replacement veins in dominantly calcareous facies; those in the southern part of the district are polymetallic fissure-veins containing pyrite, chalcopyrite, arsenopyrite, galena, and sphalerite hosted by micaceous schist and phyllite. The dominant structural trend in the southern part of the district is northwesterly and on strike with major deposits in the adjacent Seafoam mining district.

Jan 1, 1983

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Scenario-level uncertainty is a representation of large-scale differences encountered when considering ultimate mining pits optimized over various subsets of stochastic realizations. Accounting for scenario-level uncertainty allows mine plans to be assessed against several probabilistic subsurface interpretations. Scenario-level uncertainty is found through clustering stochastic geostatistical realizations and optimizing final pits across the realizations in each cluster. Where these pits are geometrically different, plans for each scenario differ. Knowing these differences allows the value of each planning alternative to be assessed based on the value and relative probability of each scenario. These results also facilitate the use of formal decision-making frameworks for planning, leading to optimization that better represents the full statistical characterization of the deposit. An example utilizing this approach evaluates both infrastructure placement and drilling program requirements. In both cases, scenario-level uncertainty improves initial plans by limiting opportunity costs and identifying additional potential.

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Scenario-level uncertainty is a representation of large-scale differences encountered when considering ultimate mining pits optimized over various subsets of stochastic realizations. Accounting for scenario-level uncertainty allows mine plans to be assessed against several probabilistic subsurface interpretations. Scenario-level uncertainty is found through clustering stochastic geostatistical realizations and optimizing final pits across the realizations in each cluster. Where these pits are geometrically different, plans for each scenario differ. Knowing these differences allows the value of each planning alternative to be assessed based on the value and relative probability of each scenario. These results also facilitate the use of formal decision-making frameworks for planning, leading to optimization that better represents the full statistical characterization of the deposit. An example utilizing this approach evaluates both infrastructure placement and drilling program requirements. In both cases, scenario-level uncertainty improves initial plans by limiting opportunity costs and identifying additional potential.