Search Documents

By P. K. Leung, S. R. Allada, P. M. Dranchuk, D. Quon

The alternating direction explicit procedure (ADEP) makes use of the boundary conditions to reduce multi-dimensional problems to a series of one-dimensional problems. The method, previously applied to reservoirs containing only an under-saturated oil, has now been extended to cover the case of natural gas reservoirs. l his involves solving a non-linear partial differential equation, application of the procedure is straightforward and no calcuIational problems were encountered. INTRODUCTION There has been a growing interest in formulating mathematical models of petroleum and natural gas reservoirs — models which permit the engineer to examine and evaluate the physical and economic consequences of various alternative production policies. The tremendous reduction in the cost of solving such models in recent years has made possible their use as an almost routine management tool. This reduction is the result not only of improved computer hardware but also of the development of more efficient mathematical techniques. The present paper is concerned with the application of a recently proposed numerical method (ADEP) to two-dimensional gas reservoirs. STATEMENT OF THE PROBLEM Given a two-dimensional Region R, bounded by a closed Curve C (Fig. 1) such that the behavior on Curve C is known, the differential mass balance for each fluid phase in R, neglecting gravitational effects and assuming Darcy's law for fluid transport, can be written as:

Jan 1, 1967

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

By John G. Payne

The Pebble deposit contains three contiguous zones. In the Pebble West zone, granodiorite stocks intrude gently warped volcanosedimentary rocks that had been intruded by diorite sills and two felsic intrusion breccias. In the Central zone, volcanosedimentary rocks are cut by diorite and granodiorite sills; the latter are genetically associated with the granodiorite stocks. In these zones, widespread potassic alteration consists of brown biotite and K-feldspar, with abundant quartz-carbonate-sulphide vein stockworks. Chalcopyrite/pyrite ratios range from 2/1 to 1/20. Diorite hosts the highest-grade mineralization, with much of it being disseminated. Patchy, later phyllic alteration is moderate and commonly depleted in copper. The Pebble East zone occupies a granodiorite stock and intruded host rocks below an eastwardly thickening wedge of barren Tertiary volcanic and sedimentary rocks up to 600 m thick. Brown biotite alteration and copper mineralization are strong, with chalcopyrite/pyrite ratios commonly over 1/1. The zone extends to a depth of at least 1200 m below surface; some drill holes bottomed in strong mineralization. Later, weak to moderate sericitic alteration removed some chalcopyrite and locally remobilized gold. The Pebble deposit has a Measured/Indicated resource of 3 billion tonnes grading 0.28% Cu, 0.32 g/t Au and 0.015% Mo (= 0.5% copper-equivalent) and an Inferred resource of 1.13 billion tonnes grading 0.30 g/t Au, 0.27% Cu and 0.015% Mo (0.55% copper-equivalent). The Pebble East zone has an Inferred resource of 2.13 billion tonnes grading 0.55% Cu, 0.34 g/t Au, and 0.037% Mo (0.97% copper-equivalent). The Pebble East zone is open to the east and to a lesser extent to the north, south, and to depth.

May 1, 2006

By R. John Caulfield

The primary water supply system for the City of San Francisco and adjacent peninsula areas consists of aging and deteriorated pipelines crossing under the San Francisco Bay (the Bay). This system is highly vulnerable to seismic damage from the nearby San Andreas and Hayward fault zones. The Bay Tunnel Project will replace the existing system with a 8-km-long (5-mi-long) tunnel underneath the Bay. The tunnel will be constructed using earth pressure balance methods and will have a two-pass lining system of precast concrete bolted, gasketed segments for initial support, and a welded steel pipe final lining. The project challenges include tunneling through both soft ground and rock conditions without any intermediate shaft access over the entire alignment. Seismic performance criteria include maintaining service flows after a large earthquake.

By G J. Delemontex, N J. Grigg

Pre-concentration of precious metal and base metal ore types is becoming more relevant with the discovery, development and operation of many lower grade deposits around the world. The fluctuations in metal prices expose many mines to risks especially dealing with low and variable ore grades.Pre-concentration, the process of concentrating the valuable metal into a smaller mass yield, effectively results in the introduction of higher feed grades to milling circuits. Gangue Rejection, the removal of lower S.G. waste rock from the circuit not only results in higher downstream grades but also potentially removes harder, non-valuable mineral, providing significant power savings within the circuit. The pre-concentration or ‘gangue rejection’ process offers a number of benefits when considering the treatment of marginal ore deposits, especially if it can be performed at a coarse crush size; these benefits include a reduction of the operating costs and the feed of more metal units to the mill.Gekko Systems has effectively utilized the Inline Pressure Jig (IPJ) to pre-concentrate the valuable metal, achieving high primary recoveries into a range of mass yields resulting in upgrade ratios between 2 and 10 times.This paper explores the benefits of pre-concentrating ‘marginal’ ore deposits prior to the milling circuit; the selective rejection of ore types that may affect either the recovery or comminution process, and also looks into the potential to effectively reduce the ‘cut-off’ grade when considering the mine planning process. Case studies of projects using the IPJ to pre-concentrate and reject gangue are also included.Pre-concentration and gangue rejection provide the potential to develop marginal ore deposits, thus providing higher grades, less gangue and more metal at a lower operating cost to producers.CITATION:Grigg, N J and Delemontex, G J, 2015. The pre-concentration of precious and base metal deposits using the Inline Pressure Jig – higher feed grades and more metal, in Proceedings MetPlant 2015, pp 296–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Following a short review of selected literature, a back analysis of stress measurements of stress regeneration in a closed mini-longwall is shown. The agreement is good, lending confidence to the parameters used in the proposed numerical model. Foundation yielding was modelled in the absence of total stope closure. A ?Prandtl? wedge was formed, coinciding with the yield point of the pillar/foundation system. Some theoretical work is used as a starting point for the formulation of a new design methodology for strike or dip stabilizing pillar/foundation systems in deep level goldmines. The existing guideline for the stability of foundations (APS< 2.5UCS) is critically examined. Finally, the advantages of the new approach, and the work required to substantiate the proposed new design methodology, are outlined.

Jan 1, 1998

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

By R Ratlou

Increased contamination due to sand in spiral feed has had a negative effect on the efficiency of spiral concentrators at Navigation Plant. The no. 1 seam at Kromdraai opencast, which was previously mined by underground bord and pillar methods, is now susceptible to spontaneous combustion because of air ingress into the old workings which are exposed in the opencast high wall. This posed a risk in the loss of reserves to burnt coal. As solutions, buffer blasting of the preceding cut to collapse bords and soft overburden dressing of un-collapsed bords were implemented to prevent air entering the workings. The latter remedy resulted in increased contamination due to addition of sand in Run of Mine. After evaluating alternatives, a low capital option was selected. The 110t/hr Teetered Bed Separator (TBS) has been installed, primarily to desand and upgrade the feed to the spiral concentrators. The unit indicated an upgrade with a yield increase of 0.4% during test work and is currently showing an overall plant yield increase of 0.97%.

Jan 1, 2006

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paver.&apos; The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal. Slurries from eight bituminous coal preparation plants in central and western Pennsylvania have been sampled and examined to determine the amount of recoverable coal in each. Examinations of the samples were made to determine the tons per hour of solids and the gallons per minute of water in the slurry; the size, ash, and sulfur analyses of the solids; and the sink-float characteristics of the larger solids. The extreme fines (—325 mesh material) from one of the samples has been examined further to determine the micron size fractions as well as the ash and sulfur content of the micron sizes. Collection of the Samples: Field trips were made to each of the plants where samples were obtained and discussions held with the preparation engineer prior to sampling. The flowsheet of the plant operation was studied and a time-period selected to obtain a representative sample. At least 20 1-gal samples of total plant bleed-off suspensions were collected at each plant in increments over designated periods belived to be typical of the plant flow Three of the samples were obtained from plants in the Pittsburgh area. Each plant supplied information on the capacity, operating time, type of cleaning equipment used, water and material balances, and auxiliary equipment. From the time required to collect given amounts of slurry and from the amount of solids in the slurry, total solids discharges from the plant were calculated and compared with the plant flow. Ash and sulfur analyses of the total solids were also checked, at some plants, with company figures. In all cases where checks could be made there was reasonable agreement between company figures and those reported here. Analysis of the Slurries: Representative fractions of properly agitated samples were examined in the laboratory to determine the specific gravities of the slurries. The solids and water were separated by filtration to check the weight of each so that the percent of solids in the pulp could be determined. From the resulting data, presented in Table I, it may be seen that the percent solids in the slurries ranges from 2.8 to 39.0 and the amount of solids from 2.61 to 45.61 tph. Size Analysis of Solids: Representative fractions of the slurries were permitted to settle and the clear water was removed by siphoning. The solids were then wet-screened at 28, 35, 48, 65, 100, 150, 200 and 325 mesh. Results of the size analyses are presented in Table 11. These results indicate the extreme variation of sizes and in most cases the degree of fineness of the solids. The amount of —325 mesh ranges from 22.5 to 84.5 pct and the amount of+200 mesh from 8.3 to 69.1 pct.

Jan 1, 1961

By Linda L. Chasko, Charles P. Lazzara, Gary Braselton, Ronald S. Conti

Preparedness is an important element of any underground mine&apos;s strategic plan in dealing with an unexpected event, such as a fire. A fully implemented fire preparedness and response plan is essential in reducing the probability and seriousness of a mine fire. This report describes the development of an underground coal mine fire preparedness and response checklist (MFPRC). The checklist is a data collection instrument for profiling both the fire prevention and response capabilities of a mine site and usually requires 3 to 4 days to complete. The checklist encompasses conditions, procedures, and equipment that have frequently been identified as the primary or contributing causes of underground coal mine fires. At least 1 day is needed underground to evaluate the water system. This entails measurements of water flows and pressures at fire hydrants, and water throw distances of fire hose and nozzles at several locations (mains and branch lines). A few of the other topics that are discussed with mine personnel include detection and suppression systems, combustible materials, mine rescue and fire brigades, and firefighting equipment. The MFPRC was developed by the National Institute for Occupational Safety and Health (NIOSH),Pittsburgh Research Laboratory. Under a Cooperative Research and Development Agreement (CRADA) with Cyprus Amax, Twenty mile Coal Co. (Oak Creek, CO), the checklist was field tested and further refined. Additional field tests were conducted at several other operating coal mines.

Jan 1, 2000

By Walter E. Vanderpool

Full scale load tests are frequently performed immediately prior to deep foundation construction to verify the design assumptions. Occasionally, load tests are performed during design development and applied to the final design for critical and non-redundant structures. We believe that full scale load tests can be very valuable and economical for projects, especially in a geologic environment where the record of full scale load testing is very limited or non-existent. The load testing for the Utah Transit Authority?s Airport Light Rail Trax project provides an example of the advantages of a load test in design development. The savings realized by the owner was in excess of $800 thousand dollars.

Jan 1, 2011

By S. Uludag

Spontaneous combustion of coal has been studied by laboratory techniques using an apparatus in a small-scale laboratory testing. Coal?s inherent characteristics can be measured using Differential Thermal Analysis (DTA) and Crossing Point Temperature (CPT) methods. The DTA curve obtained after testing is compared with actual inherent moisture and its effect on spontaneous combustion has been investigated. It has been found that the Wits-Ehac Index increases as the inherent moisture of the sample increases. Therefore it can be deduced that liability to spontaneous combustion increases with increased inherent moisture. In addition, volatiles have a catalytic affect on self heating immediately after the inherent moisture is reduced. This is identified as stage two in the thermogram. The inherent moisture has a cooling effect during the initial stages of testing and is visible in the DTA thermogram. In addition, while an increase in carbon content means an increase in Wits-Ehac Index value, an ash content decreases the likelihood of on spontaneous combustion. Keywords: Spontaneous Combustion, Differential Thermal Analysis, Crossing Point Temperature, Moisture, Coal, Laboratory Testing.

Jan 1, 2007

By Daniel Hauer

Blocking. (5) The “blocking” of boulders is a much cheaper way of breaking them up than “mud capping.” It should always be used in preference to that method except when too much time will be consumed by a crew of men waiting for the drilling to be done, as shown in example of cost No. 1, as given under “mud capping.” Under such circumstances the time consumed would be a greater cost to the contractor than the extra amount of dynamite. Then, too, on large thin boulders to drill one hole would result only in breaking the stone into such pieces as would again have to be broken; and the many holes might equal the cost of extra dynamite. Under such circumstances if method (6) cannot be used, “mud capping” will have to be resorted to, to do the work economically.

Jan 1, 2006

By C Li, D O’Dea, R Moreno-Atanasio, T Honeyands

The behaviour of iron ore granules in the feeding process of sintering is significantly influenced by the material properties of the granulated mix. Therefore, the measurement of key material properties of the iron ore granulated mix is indispensable prior to the simulation of the sintering process based on the discrete element method (DEM). In this paper, three key property parameters of the iron ore granulated mix, apparent density, elastic modulus and rolling friction coefficient, were measured in laboratory-scale experiments. For different sintering processes, the moisture content of the granulated mix normally varies according to the specific requirements for granule size distribution and operating conditions. Therefore, understanding the effect of moisture content on the property parameters of iron ore granules is very helpful in accurately determining the property parameters for DEM simulation work. In this paper, six groups of iron ore granule samples with six levels of moisture contents were prepared through granulation and the trends in apparent density, elastic modulus and rolling friction coefficient with the increase of moisture content were plotted and analysed based on the measurement results. The results show that as moisture increases from 6.9 per cent to 9.1 per cent, the apparent density decreases from about 3000 to 2800 kg/m3. With moisture increasing within the same range, the elastic modulus first decreases from over 200 MPa to below 100 MPa and then reaches a relative constant value of about 40 MPa at higher moisture contents. Rolling friction coefficients are measured using two methods with both indicating a similar trend, with the rolling friction coefficient first decreasing and then rising as moisture increases from 6.9 per cent to 9.1 per cent. The relationship between µr and µ’r is assumed to be similar to that between static and dynamic friction coefficients.CITATION:Li, C, Moreno-Atanasio, R, O’Dea, D and Honeyands, T, 2017. Variation in property parameters of iron ore granulated mix with moisture content, in Proceedings Iron Ore 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J L. Mauk

The Martha epithermal Au-Ag deposit contains multiple generations of quartz veins with a range of textures. We examined: +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; vein textures, +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; crosscutting vein relationships, and +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; the paragenetic sequence within the pit walls as well as a wide range of hand specimens. Samples include host rock, breccia, and veins, but these groups are not distinct; instead, they form a continuum. &nbsp; Veins at Martha mine show a wide range of textures on a local scale; these textures also change significantly over both the lateral and vertical extent of the pit. Common textures include crustiform bands, comb quartz, colloform bands, platy quartz, massive quartz, drusy quartz, sedimentary textures and brecciation. &nbsp; Vein grades relate to textures. Many textures, including crustiform, platy, cherty, and sedimentary textures display predominantly low grades, but some textures are linked with high grades, such as ginguro, massive and comb quartz where they are associated with visible base metal sulphides and/or electrum. Host rocks and most breccias are low grade, as most samples contain &lt;2 ppm Au.

Jan 1, 2006

The Winton Basin is one of three Southland sub-basins. The oldest known sediments are Early Oligocene terrestrial shales, sands and lignites deposited in half grabens formed as a result of oblique extension. A marine transgression in the Oligocene deposited mid-outer shelf to upper bathyal mudstones. Shallowing of the basin and tectonic quiessence lead to limestone deposition in the Early Miocene. Regional tilting led to uplift in the north and east and deposition of terrestrial lignites and gravels across the basin and the basement high to the south.

Jan 1, 1992

To mine uraniferous sand-stone in an economically feasible and environmentally compatible manner without placing men underground. Approach Uraniferous sand is remotely extracted through a single borehole by cutting Into the are around the borehole with a high pressure water Jet, and pumping the resulting slurry to the surface. How It Works A 16-inch-diameter borehole Is drilled from the surface down into the burled mineral deposit, and the mining tool Is installed. High pressure water Is released as a jet from a nozzle In the mining tool to erode the are, forming a slurry that flows to the bottom of the cavity. The slurry Is drawn Into Inlets located near the bottom of the drill string. See drawing. After being pumped to the surface, the slurry is weighed, metered, and checked for radioactivity. It is then deposited Into one of a pair of sumps. Water collecting in the sumps drains Into an adjoining pond for reuse. Thickened are In the sumps is removed and placed In piles.

Jan 1, 1978

By Mike Johnson, Niels Verbaan, David Dreisinger

The Search Minerals Foxtrot project in Labrador represents a significant Canadian resource of rare earth elements rich in the sought after heavy rare earth elements (19.8% HREE/TREE). A preliminary economic assessment of the project indicated that the project is technically feasible and economically attractive. A variety of metallurgical test programs have been undertaken which have led to significant streamlining and simplification of the process flowsheet. The improved flowsheet should allow Search to reach production earlier and will use conventional processing equipment. The results of these test programs are presented and discussed in this paper.

Jan 1, 2014

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941

By Scott Rosenthal, Logan Connolly

Butte, Montana holds a prestigious place in the history of mining, deemed “The Richest Hill on Earth,” containing a plethora of underground mines. The Orphan Boy/Orphan Girl underground mines, on the western side of Butte, operated from 1895-1956 producing zinc, lead, silver, and manganese. Today, the Orphan Boy mine is part of Montana Tech’s Underground Mine Education Center (UMEC) and the Orphan Girl mine houses the World Museum of Mining. Underground development in the Orphan Boy mine continues to progress as students from Montana Tech receive hands-on underground training; in addition, the UMEC is a multi-disciplinary research facility. Repeated underground blasting occurs in close proximity to old mine workings (wood supports installed circa 1950 or earlier). Research began to determine the impact of underground blasts on nearby pre-existing structures. Using the ISEE Field Practice Guidelines for Blasting Seismographs, one seismograph monitors the predominately-wooden structures to measure their response during each underground blast and one seismograph positioned on the surface to monitor surface structure response to the blast. This paper presents the findings of the research conducted to date for the project. The paper includes analysis of the research data, and conclusions determined from the research. Recommendations for the future work are included as well.

Jan 1, 2018