Search Documents

By H. Soto, J. Jara, F. Nava

"A combination of oxidation and precipitation was used to eliminate cyanide from gold milling effluents. Preliminary laboratory work developed with both synthetic cyanide solutions and with industrial effluents indicated that ozone can easily destroy free cyanide and weakly complexed cyanide (i.e. copper and zinc cyanide). In this case the reaction is quite fast and seems to be controlled by the mass transfer of ozone to the solution. Experimental results indicate that free cyanide and weak-acid dissociable cyanide in mill effluents can be reduced to less than 1 ppm. However, the iron-cyanide complexes proved to be quite resilient to destruction with ozone and they remained in the solution even after most of the free and weakly complexed cyanide was destroyed with ozone. These results were confirmed in a pilot trial developed at the Sphinx plant in northern Quebec.To deal with the problem presented by the presence of the iron complexes two different approaches were studied: use of a combination ozone-ultraviolet light oxidation, and the precipitation of iron-ferrocyanide complexes in the residual solution after ozonation. This last method proved quite promising since reduced the total cyanide levels of industrial solutions assaying as much as 250 ppm to less than 1 ppm of total cyanide. Control of the · pH of the solution was the key to obtain the precipitation of the iron complexes. The use of iron to precipitate cyanide complexes has the advantage of being less expensive and less toxic than copper (used by the Inco process)."

Jan 1, 1992

By H. I. Kim

The leaching of a complex matte in chlorine and chloride media was studied. The matte was prepared from manganese nodules by the reduction smelting-sulfidation route. From XRD analysis, the major phases of the matte were identified as CuFeS2, CuS2, (FeNi)9S8, (FeNi)S2, Ni9S8, Ni3S2, (CoFeNi)9S8 and Co metal. Investigated were the chlorine, hydrochloric acid, hydrochloric acid-oxygen, ferric chloride, ferric chloride-oxygen, cupric chloride and cupric chloride-oxygen systems. The results are discussed in terms of reagent concentration, retention time, leach temperature and gas sparging rate. The chlorination process resulted >99% metal extraction efficiency within a short retention time and at atmospheric temperature. However, there were no preferential extractions of Cu, Ni and Co with respect to Fe. The cupric chloride-oxygen system produced leach liquors with the lowest Fe content and with a high base-metal extraction. Sulfide sulfur was converted to mixtures of elemental sulfur and sulfate in all the studied systems.

Jan 1, 2009

By Fredrik Sarvell, Leo-Ville Miettinen, Veli-Matti Uotinen

"Abstract The continued concentration of building activities in cramped areas of city centres means more underground construction and facilities. Demand to minimize execution time and any kind of disturbance to business, general traffic, people and nearby technical structures is increasing. To answer these challenges foundation business has to develop schedule-wise and technically reliable deep excavation and foundation solutions in vulnerable surroundings and challenging soil conditions.Drilled pipe pile wall – RD-pile wall – is a combination of Ruukki drilled steel pipe piles and interlocking sections. Individual RD piles, typical diameters between 219 mm to 610 mm, are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole hammer (DTH) using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings.RD-pile walls have been used as permanent and temporary retaining walls for different kinds of demanding excavations and structures, such as bridge foundation, as quay wall and as sealing structure in rehabilitation of an existing dam. Rigidity and watertightness of the lower end of the RDpile wall is being researched as well as fire design issues examined. One of the most fascinating RDpile wall solution is to utilize the wall as a permanent underground basement wall. Reliable and rigid connection to bedrock decreases the bending moment and deflection of the wall and good fire resistance in addition to large variety of pile dimensions and steel grades gives possibilities to design and execute a cost-efficient basement wall and foundations without temporary retaining wall works. 1. IntroductionIn northern Scandinavian soil conditions, installation of sheet pile walls, or even secant pile walls, is often problematic due to the existence of hard and large boulders in the overburden, and especially when the retaining wall structure should penetrate to or into the hard bedrock. On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid-1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers)."

Jan 1, 2014

By Y Ren

?ptim?sgtion t?ols nos ope? 0iu ?ingc s?ch as the cche??ling and?pi? k?(i?isatTon tool{ ?ave bg?ome(?osd-dvfective way? to e?iluata open`¦it mi~e!p?n?ept as w?ll asá?}prmv?ng mine?projecW`value> ?owerez

Aug 12, 2013

By A. M. Poston

Introduction of radioactive elements into ore samples and/or pregnant liquors and radiometric tracing thereof have greatly improved control of fusion and extraction studies on beryllium ores and products. Extractive metallurgical research on beryllium, normally guided by the usual laborious analytical methods, is both costly and slow. Recognition of this problem by the Bureau of Mines led to the development and application of radioisotope tracer techniques" as a substitute for chemical analysis at the Salt Lake City Metallurgy Research Center, The result was that much faster progress at significantly lower cost was achieved. This report discusses the problems encountered and resolved in using radioactive tracers and radiometric methods, defines the conditions and techniques for their effective use, and delineates the limitations and flexibility inherent in applying such methods in laboratory-scale beryllium research.

Jan 1, 1962

The placer mining industry of the West Coast region of the South Island is based largely around the production of alluvial gold, although other valuable minerals are also present. Since the first major discoveries in 1864-65, reported gold production has totalled around 264 t (8.5 Moz). During the past 10 years, annual production has totalled around 1460 kg (47,000 oz). It is anticipated that gold production over the next three years will continue at a level of 1400-1800 kg.   Annual gold production peaked during 1866 at approximately 17,170 kg (550,000 oz) and has not exceeded 100,000 oz since 1885. This reflects the ease with which gold was won from shallow, rich deposits that were present at many localities. Subsequently, there has been a general decline in the availability of this type of deposit, a trend that will continue in the future. This paper outlines the present state of placer mining in the West Coast region, gives some historical background to the industry and briefly predicts future trends.

Jan 1, 1997

By C. Sykes, E. Turner, M. Wyart-Remy

This paper follows that of the Milos Conf, 2002 and examines the collection and reporting of SDIs in the industrial minerals industry in Europe. It compares the characteristics of the GRI Reporting Guidelines, with its Metals and Mining Sector Supplement with those of the EU DG Enterprise Scheme, launched in 2001. The particular issue of SME's and companies which are not publicly traded is examined. The pros and cons of participating in such schemes is a central theme of the paper. The paper concludes that there and many business benefits for these companies in participating and submitting their data. The European Commission Scheme is strongly recommended for companies in the sector which are SME's and not-publicly traded as well as large firms who are listed on European Stock Exchanges.

Jan 1, 2005

By R. G. Vardiman, M. R. Achter

Observations of dislocation structure in niobium are presented using two techniques. Triangular pits developed by electroetching are confined to orientations in the stereographic triangle between the (111) pole and planes of the (1ll) zone and require the presence of carbon. Some unusual electroetching phenomena at other orientations are noted. A chemical etch of dislocations decorated by the addition of carbon to 50 ppm reveals the complete dislocation line structure in a surface layer up to 30 p deep, with a resolution of less than 1 p. This effect is independent of surface orientation. The structure of subboundary nets may be resolved for misorientations up to about 1'. Dislocation structures found in strain anneal grown crystals, such as helices, prismatic loops, and high-density areas, are observed. The measurement of dislocation density is discussed and values obtained in different ways are compared. IN the course of some work on the response of refractory metals to thermal-mechanical treatments, it was desired to examine the defect structure of relatively low dislocation density crystals of niobium in bulk form. Surface and bulk methods for the observation of dislocations have been reviewed by ~melinckx,' and include etch pitting, decoration, and various X-ray techniques. The dislocation line structure has been developed by decoration in a few metals, although observations were limited to certain orientations, or by the coarseness and nonselectivity of the precipitate. The most commonly used technique is etch pitting. In niobium, etch pits have been developed chemically'0," in material of high impurity content and electrolyti-cally'' in relatively pure material. In this paper, etch pits developed electrolytically, and the dislocation line structure of a surface layer developed by decoration and chemical etching, are examined, and observations are presented from both techniques. EXPERIMENTAL METHODS Our starting material was electron-beam-melted niobium, swaged to 4 or -in.-diam rod. Chemical analysis is given in Table I. Single crystals were grown by a strain anneal technique using 1 to 2.5 pct of strain and growth temperatures of 1700" to 2300"~.'~ Some crystals grown by zone melting were also examined. The desired surface orientation was exposed either by spark machining or by sectioning with a cut-off wheel and prepared for etching by electro-polishing.

Jan 1, 1969

Jan 1, 1962

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By A. Basçetin

Equipment selection in mining engineering is one of the most important decisions that affects the mine design, production planning and economic parameters in open pit and underground mining. Mine planning engineers generally use their intuition and experiences in decision making. Mostly, linguistic variables (the weather is raining, soil is wet, etc.) come into question and decision-makers may not know how these variables are computed. Since the advent of the fuzzy set theory, these uncertainties are easily interpreted in the decision-making process. The development of computer technology and programming of colloquial language with expert systems have considerably reduced decision-makers? burden. This paper reviews the development of a computer programme software called EQS (EQuipment Selection) that automates equipment selection in mining engineering using fuzzy set theory. The EQS with an introduction of the concepts and theories of multiple attribute decision-making, the fuzzy set theory, and EQS applications to mining industry problems with case studies are presented

Jan 1, 2006

By Rob Barber

This paper shares the experience of the Alberta Energy and Utilities Board (EUB) Field Surveillance Branch over the past few years in building relationships with Aboriginal communities. Our goal is to provide and encourage best practices that may benefit you and your organization and result in strong, mutually beneficial relationships with a focus on Aboriginal communities. Historical information provides insight that aids in establishing effective working relationships with Aboriginal communities. An important component is appreciation of the perspective of these communities, which is achieved through awareness training. The use of local Aboriginal resource people as part of the training is recommended. A plan that is supported by management and staff is essential and lays the foundation for successful relationships. However, the plan must be flexible enough to change as circumstances warrant. The concept of having local people in communities address local issues is essential. This ?grass roots? approach, combined with the goal of exceeding a community?s expectations with respect to addressing issues, will go a long way to establish trust and credibility. Measuring the effectiveness of this work is the final building block to complete the picture.

May 1, 2004

By Nick Barton

A recent analysis of 145 TBM tunnels of more than 1000km total length has helped to quantify the time dependence of utilization (U). In fact U = Tm, where T is time in hours and m is a negative gradient of deceleration. In poor quality ground, gradient m has a strong dependence on rock mass quality Q, for example m ˜ -0.5when Q = 0.1. Good investigation is critical for ensuring faster TBM tunneling then drill-and-blasting, which tends not to slow down (in m/hr) as the tunnel length increases. Anew design model called QTBM allows more reliable prognoses be made, and occasionally will disqualify the TBM solution.

Jan 1, 2001

By J. V. Ghelarducci, M. A. Sharpe, D. G. Chedgy

This article presents a novel design, called the Climax, High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 ~ 660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax, magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Feb 24, 1997

By Luis Valle, Fredy Zegarra, Ernesto Vizcardo

El uso de los procesos estocásticos y cadenas de Markov se ha desarrollado solo para estudios de probabilidades en la rama de las ciencias matemáticas y como una opción a las descripciones tradicionales en el campo del procesamiento de minerales, se realizó una comparación entre ambas metodologías para lo cual se cuenta previamente con varios análisis granulométrico proveniente de los molinos de Bolas industriales de la empresa Shougang Perú y pruebas granulometrías de Molienda de Sider-Perú, comparar en ambos estudios, como el probabilístico (Cadenas de Markov) y el cinético (Selección y fractura) ofrecen un buen acercamiento al resultado experimental, dando como una buena alternativa el primero por su uso del manejo estocástico.

Sep 1, 2017

By George Boucher, Simon Williams, Neil McBride

"The aim of these analyses was to utilise the latest available production information for the Wandoooperation to determine the optimal blasting parameters, costing’information and predicted results(fragmentation, muckpile shape and vibra.tton). Much of the data used as input was made availablefrom the information gathered during the excavation of the test pits during 1995. As with any“planning stage” analyses, many assumptions were required to fill gaps in the available data."

Jan 1, 1998

Several glacial episodes have been distinguished in the Shotover Valley. These produced fluvioglacial aggradational deposits downvalley from the terminii, commonly with well-preserved terrace treads, as exemplified near Skippers. Chronological links can be determined between the Shotover tills and sediments and assessed equivalent deposits in the Wakatipu Basin/Kawarau Valley region through axial valley profiling. Constructed relationships suggest older Shotover events were probably large and left little detrital deposits within the valley. In contrast, the younger advances were smaller and valley-constrained. They are modelled as being wholly of Waimea or Otira Glaciation age, advances from the latter period producing the visually distinctive flights of terraceremnants. Both the terraces and the inner gorge, now occupied by the Shotover River, have been extensively worked for alluvial gold. Enrichments in the former environment have predominantly been as bottom or intermediate lags produced during degradation phases of catchment erosion. Surface lags have been locally targeted. Placer mining in terrace areas involved both tunnelling and sluicing techniques. In the modem river the greatest concentrations were on the schist or false bottoms, although flood gold has always contributed to the returns. Placer mining techniques here were highly variable.

Jan 1, 1998

By Doris M. Hyde

In the past, mining has represented between 11% and 12% of the gross domestic product (GDP). In 1982, mining contributed over $150 million to the estimated $1.4 billion GDP.2 Overall economic growth for 1983 was projected at about 2%, primarily as a result of increased tourism. The inflation rate remained at or fell below the 1982 level of almost 4%. The Government continued its efforts to strengthen the industrial base by improving infrastructural systems and the establishment of a free trade zone. Laws against property ownership by foreigners or foreign-owned companies were strengthened, but the prohibition was softened to allow for close family inheritance. Otherwise, Government approval must be obtained to retain property acquired through inheritance, court order, mortgage, or other means. Special consideration was granted to foreign investors seeking to promote industries beneficial to the economy.

Jan 1, 1985

By George Goble

I hope that after the long evening and all the exercise that some of you took you won't be completely exhausted to listen to a little bit about pile testing. The topic that 1 have been given is pile testing. It seems to me useful to break this topic into some smaller pieces so that we can try and organize our thought a bit. As I understand the terms "pile testing", I believe we are really referring always to capacity, one way or another, so I am suggesting that we organize the things we are doing in terms of measurement of soil capacity and pile capacity. There are obviously two failure modes and we frequently speak of pile integrity rather than structural pile capacity, but it's really capacity that we are concerned about. Further within these breakdowns I am suggesting that we might look at the topic of soil capacity in terms of static methods and dynamic methods and, finally, within each one of these, measurements of axial capacity and measurement of lateral capacity. Also here some of these subdivisions might be there for the purpose of symmetry and finally the same sorts of breakdown in Pile Capacity area.

Jan 1, 1994

By Jerry Gagnon, Matt Burr, Dave Evans, Timothy Ellis, Davies Kakengela, Abbas Mirza, Larry Webb, François Leclercq, Andrew Johnston

Lead-based alloys are the primary anodes used in electrowinning from sulphate-based aqueous systems. Lead anode technology has evolved over the years, migrating from pure lead and lead-antimonial alloys to the present day lead-calcium-tin alloys for copper electrowinning and lead-silver alloys for zinc electrowinning. It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new alloys and production processes, the industry still has unresolved issues related to untimely corrosion which limits anode life and may lead to higher contaminant levels in the metal being produced. Lead anodes corrode because of the difference in the chemical/electrochemical potential across the microstructural features of an anode. Given a very high purity material, we find that the grain boundary areas corrode significantly faster than the rest of the grain. The desire to minimize grain boundary corrosion by a balance of alloying element selection and microstructural design allows the grain boundary area to be engineered. However, operational issues can lead to unexpected corrosion behaviours which we will discuss moving forward. The comments in this work, though directed toward copper electrowinning, can be extended to similar phenomena in other metals electrowon from sulphate media (i.e., zinc, nickel, cobalt, manganese). The lifecycle of electrowinning anodes is dependent upon electrowinning tankhouse operating conditions and maintenance of the anodes, including cleaning and straightening. This paper will focus on the operational aspects of maximizing the utilization of lead electrowinning anodes.

Jan 1, 2015