Search Documents

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2003

By D. Grabowski, Z. Pokryszka

A study carried out in the iron basin of Lorraine (North-East of France) highlighted the existence of under-oxygenated and noxious gas emissions (carbon dioxide, radon…) in vast built-up areas related to former mine workings. Site investigations showed that the gas flow was mainly due to natural thermal air circulation between old mines and external atmosphere. The main hazards associated with this flow of gas and its potential accumulation in confined volumes in buildings are asphyxiation and intoxication. A further study is in progress in order to better understand the origin of the gas generation within the old iron mine workings. Following the first hypothesis, the carbon dioxide emission is mainly due to the specific hydro-geo-chemical process associating the pyrite oxidation with the acid dissolution of carbonates. KEY-WORDS : gas, emission, iron mine, pyrite.

Jan 1, 2003

By Zwaan J, Kepa J

Ok Tedi mine has become one of the major copper producers in the world. In the process of becoming of age, it overcame the challenges of operating in a locality which is young in geological terms, experiences very high rainfall and has a topography which gives rise to frequent landslides. This paper discusses some of the geological, mine and geotechnical engin- eering aspects of the Mt Fubilan ore deposit.

Jan 1, 1991

Gold in the stibnite veins of Costerfield, Victoria, was described in 1922 1, prior to any mineragraphic examination, as (a) free yellow gold (b) free rusty gold and (c) combined gold. The free yellow gold occurs in quartz and will amalgamate with mercury. The free gold of dull, rusty or copper-red colour occurs in massive stibnite and has been stated to resist amalgamation with mercury. The dull colour is only skin deep and the colour is bright when the rusty gold is scratched. The appearance of the rusty gold is spongy or cellular and it generally occurs near small cavities in the stibnite. The suggestion that the cellular character indicated the removal of a certain amount of stibnite leaving a residue of se.condary gold cannot be sustained.It now appears probable that the rusty gold is formed by the primary dissociation of a gold antimonide and is distinct in origin from the normal yellow gold which is deposited with quartz or stibnite from auriferous mineral solutions.The combined gold referred to in the earlier paper was the gold contained in the stibnite as revealed by assay. Such gold was at first thought to be either dissolved in the stibnite or else present as free interstitial particles too minute for observation in transmitted light in thin sections.Subsequent examination of numerous polished,surfaces disclosed the small particles of gold occurring in the grain boundaries in aggregates of fine grained stibnite 2. The assumption that all the gold in the stibnite, as revealed by assay, occurred in this way is now known to be incorrect, because limited amounts of a gold antimonide have been found in the veins.

Jan 1, 1952

By Dave Bigby

Hatworth Colliery, operated by RJB Mining (UK) Ltd, is successfully mining the Deep Soft Seam at a depth of 1000m using single face retreat longwalling. The seam is characterised by a weak roof generally comprising 4 to 6m of well bedded carbonaceous mudstones overlain by weak siltstones. The paper describes the layout and support design strategies which have enabled the colliery to adopt sole support by rock reinforcement techniques for its longwall gateroads. To achieve this success the colliery layout has had to be radically modified to take account of the in-situ horizontal stress field. The layout is also closely controlled by environmental considerations, the seam being one of the gassiest in the UK Economic support by strata reinforcement has been achieved using a combination of rockbolting of the roof and sides installed at the face of the heading, and systematic double birdcage cable bolting installed on drivage and supplemented ahead of the retreating panel. The layout and support strategies have been developed through a combination of detailed underground measurement of support and stress parameters backed up by numerical modelling using FLAC. The FLAC modelling has paid particular attention to careful representation of bedding properties and validation through underground stress measurement.

Jan 1, 1996

By C. Musingwini

The Bushveld Complex is economically significant and strategically important to South Africa, thus it is imperative that optimal extraction of platinum group metal (PGM) resources on the Bushveld Complex is achieved. Optimal extraction broadly requires that the maximum amount of ore is extracted by excavating and hauling the minimum amount of waste in the shortest possible time, at the least cost, and in the safest and most environmentally acceptable manner. In open-pit mine planning this entails among other things, minimizing the waste stripping ratio, whereas in underground mine planning it includes minimizing the metres of waste development. In conventional mining, the main development that is in waste or partly in waste and defines the mining grid pattern includes levels and raises. It was prudent to consider optimizing level and raise spacing in conventional mining because the method is a prevalent mining method on the Bushveld Complex accounting for nearly 70% of platinum production.

Jan 1, 2010

By R. A. Harris

In this study Pt-Al thin films were prepared via electron beam physical vapour deposition (EB-PVD) with an atomic concentration ratio of Pt25:Al75. These films were heat treated at temperatures ranging from 150°C to 650°C for annealing times from 4 to 60 minutes. The resulting microstructure of these thin films were obtained via secondary electron imaging used in conjunction with depth profiling with the aid of scanning auger microscopy (PHI 700).Elemental maps of the micrographs were obtained. Simulations, based on a chemical potential Monte Carlo method1, were run for various interaction parameters. From these simulations theoretical depth-profiles and proposed microstructures were obtained. These were compared to the experimentally measured depth profiles and elemental maps. Keywords Monte Carlo, chemical potential, depth profile, Pt-Al thin films.

Jan 1, 2011

By R. H. Zeng

Many subsidence researchers in the U. S. have developed new empirical function methods to predict subsidence, or attempted to validate some empirical functions developed by foreign researchers for use in the U. S. An attempt is made in this paper to develop a new empirical function to predict a surface subsidence basin due to longwall mining. In the U. S., the emphasis of empirical methods for the subsidence prediction over longwall panels has been in large part on determining the profile functions for the major cross-sections of a subsidence basin. In this approach, the surface monuments are usually laid out along the major cross-sections and thus, the subsidence profiles developed are restricted for subsidence prediction along the major cross-sections. However in practice many monuments or surface structures for which subsidence prediction for damage evaluation is required, are not laid out along the major cross-section of the basin. In such cases, it is difficult to get either the empirical profile function for the cross-sections where these structures are located or to predict their subsidence based on the profile function developed for the major cross-sections. Therefore, there exists a strong need to develop a subsidence basin function with a reasonable degree of accuracy, which can be determined or confirmed by the data of scattered monuments on a surface basin. The same subsidence basin function can also be used for prediction of subsidence for any arbitrary points over a longwall panel. In 1982, He (1) proposed the clastic theory, for which he developed the basic differential equations describing the movement and deformation of overburden due to underground mining, and performed the selection of best solution for the equations. He found that the Weibull dietribution is the optimal solution. The Weibull distribution has three parameters that vary to fit the subsidence profile so well that the profile function derived from it provides a high degree of accuracy in subeidence prediction. However the results

Jan 1, 1986

By H. R. Babitzke

The purpose of this investigation was to develop an alloy of columbium for use at high temperatures and for nuclear applications. The properties of possible alloys were determined, and the more promising ones were selected for further improvement. Criteria for selection were machinability, hardness, workability, tensile strength, and oxidation resistance. Thirteen 100-gram ingots, ranging from 100 percent columbium to 100 percent vanadium, were prepared and subjected to various tests. Also included for comparison were zirconium and the zirconium alloy, zircaloy-2. Test results showed that a columbium alloy, containing 10 atomic percent vanadium merits further development. Besides being workable at room temperature, the columbium-10 atomic percent vanadium alloy has oxidation resistance superior to the other alloys of the series and is also superior to zirconium or zircaloy-2. The latter two materials have comparable neutron-absorption cross sections. The strength and hardness values of the alloys tested were found to increase with increasing vanadium content, reaching a maximum at 50 atomic percent vanadium and decreasing with further increase in vanadium. This behavior is typical of binary alloys wherein each element will retain any proportion of the other in solid solution. INTRODUCTION There is an increasing need for alloys for service at high temperatures. Since current world reserves of columbium metal approximate 1,500,000 tons (1),4 this metal is now readily available. Columbium can ties; be considered a practical base material for high-temperature alloys required in nuclear reactors and in aircraft and space vehicles. General requirements chosen are: (1) Workability, (2) satisfactory mechanical properties at temperatures approaching 1,000° C., and (3) resistance to oxidation at such temperatures.

Jan 1, 1962

By R. K. Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a cascading pillar failure, occurs when one pillar in the mine layout fails, transferring its load to neighbouring pillars and causing them to fail in succession. Recent examples of this kind of failure in coal, metal and non-metal mines in the USA are documented. Mining engineers can limit the danger presented by these failures through improved design practice. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This is used as a basis for three design approaches to control cascading pillar failure: containment with barrier pillars during pillar splitting; prevention with panel pillars of high width-to-height ratio and small-centre mining; and full extraction by retreat mining

Jun 19, 1905

By G. Zhan, P. Mousset-Jones, G. Danko, J. J. K. Daemen, C. Mezei

Paper presented at the conference Risk assessment in the extractive industries, held in Exeter, 23-24 March 1994, and first published London: IMM, 1994, preprint volume. 18pp., 12 refs. (Originally entitled: Tunnel roof diagnosis using a robotic sensor test bed.) An integral roof diagnosis method is proposed to assist in assessment of risk regarding the stability of an excavation. A Robotic Sensor Test Bed (RSTB) is being developed for the characterisation of roof stability. The sensor test bed consists of a sonic/ultrasonic wave response sensor, a laser surface profiler and a surface temperature sensor. These sensors are mounted on an articulated robot manipulator for performing remote-controlled or fully automated diagnoses. A number of laboratory and field sonic/ultrasonic tests were conducted. A high-energy ultrasonic transducer and an impact device were used to resonate rock slabs. The fracture depths of the slabs were found to be inversely related to the measured resonance frequencies. The agreement between identified and actual dimensions was acceptable. Field tests also showed that loose rock on the surface can be clearly distinguished from solid formation by comparing their wave responses. The robotic laser profiler part of the RSTB was used to measure surface geometry. Different scanning methods are being developed to achieve the fastest and most precise measurements and to provide pertinent information about rock joints and major fractures

Dec 1, 1994

By A. M. Richardson

The significance of a massive sandstone unit in the immediate roof to longwall support weighting is well known. If the unit lies in the main roof above the zone of caving, its influence becomes more difficult to calculate using traditional methods. Much of the reserves at Cyprus Plateau's new, multi-seam Willow Creek Mine are located in the A Seam. The massive Kenilworth Sandstone is typically situated 21.3 m (70 ft) above the A Seam in the main roof and is on average 14.6-m (48-ft) thick, ranging to 29.0-m (95-ft) thick. This paper describes the application of distinct-element modeling to determination of the appropriate yield capacity for supports at Willow Creek. The modeling was determined to be useful for understanding support loading mechanisms and as an aid to engineering judgment in selecting supports.

Jan 1, 1996

By Gordon M. Matheson

The factors which control chimney subsidence sinkhole development in weak rock were assessed by analyzing the characteristics of approximately 3000 chimney subsidence features along the Colorado Front Range. The area of study included features developed over abandoned mines in the Colorado Springs Coal Field, the Boulder Coal Field, and the Foothills District. The approximate locations of the areas studied are shown in Figure 1. Data were collected for sinkholes occurring over both room and pillar, and retreat mining areas in coal seams with a wide range of dips. The location, size, and approximate time of development of each sinkhole were documented. From these data, relationships were developed which describe the time rate of observable sinkhole development and the relative location of sinkhole development with respect to mined height, overburden thickness, and type of mining for relatively flat-lying coal seams. In addition, the observed locations of sinkhole development over steeply dipping coal seams were assessed for portions of the study area.

Jan 1, 1986

By A. M. R. Neiva

The WNW-ESE-trending hydrothermal veins cut alternating mica schists and quartzites of mainly Ordovician age and, to the west, a Hercynian muscovite-biotite granite. They have been prospected and developed to a depth of 300 m and reserves of 20 t Au estimated. The paragenetic sequence and chemical compositions of the ore minerals are generally similar to those at Jales to the south. Gold, electrum and aurian silver form inclusions in arsenopyrite, pyrite, galena, sphalerite, pyrrhotite and quartz and also occur in veinlets that cut these minerals. Silver has been found in gold, electrum, aurian silver, tetrahedrite, freibergite and the Ag-Pb-Sb sulphide owyheeite. Early arsenopyrite crystallised at an estimated 480 degrees C and the more common, later arsenopyrite in which Au and Ag are generally included at 430-300 degrees C. Sphalerite crystallised at 307-100 degrees C. Monoclinic pyrrhotite may have been formed by the inversion of hexagonal pyrrhotite at 248 degrees C

Jun 16, 1905

Coking coals are very much in demand on a world wide basis, particularly the higher rank coking coals, which form an important part of many coking blends and which represent the smallest portion of the world'scoking coal reserves. Conventional coke oven plants, using these coals, will predominate at least until the next century.Blending schemes for conventional coking require definition of the basic properties of coals so that the factors influencing the carbonization behaviour may be assessed. Several concepts, which are relatively simple, ate available to help promote a better understanding of the bask factors controlling -coke strength and are also useful in suggesting possible lines to follow in the blending of coals for coking.The interpretation of carbonization behaviour and coke structure in terms of petrographically defined coal rank and type provide a basis for planning and exploitation of coal Teserves. The optimum parameters for coking are suggested as follows.1. Type- Vitrinite content (% m.m.f. by volume) 55 ± 5%2. Rank- Mean maximum reflectance of vitrinite 1.30 ± O.10% Carbon content of vitrinite (% d.m.m.f.) 87·5 ± 1·0%The value of a coal should be assessed in relation to all its possible uses in blends. This is a more realistic and productive approach, as compared with considering coals only in relation to the results of blending with"good" coking coals. Blending schemes have been outlined to assist in the assessment of the blend potential of coals of all ranks and types.Reserves of higher rank coking coals in N.S.W. are very limited and should be conserved by blending with the low rank coking coals, of which there are large reserves.Examination of blending theories in relation to N.S.W. coals suggest that blends in the broad categories of minimal downgrading of the higher rank N.S.W. cok...

Jan 1, 1972

By C. Pelley, A. Piche

"The Canadian mining industry faces the prospects of a severe shortage of graduate mining engineers over the next decade. This arises from three factors: first, a growth in industrial activity; second, the average age of company engineering and management staff; and third, the reduced number of students in engineering faculties around the world. This paper aims to identify the critical factors underlying the trend of inadequate recruitment into higher education for mining and to examine means of alleviating the problem.This paper is based upon surveys of potential and current students and graduate mining engineers from four mining schools. An attempt is made to understand institutional and industrial images, career prospects and what is required to attract enough high-calibre young people into mining education over the next decade.IntroductionThe mining industry has started to experience a severe shortage of graduate mining engineers which is likely to persist and even worsen in the short- to medium-term.This arise s from three principal factors:1. a recent and strong growth in mining activity, which surpasses that experienced through the 70s, before the recent international industrial recession; .2. an increasingly older average age of mine engineering employees, at least in the industry's larger companies; and3. problems associated with maintaining adequate mining undergraduate recruitment levels ."

Jan 1, 1989

By J. P. Landriault, F. W. Harrison

"Zinc-iron alloy coatings can be produced by either thermally alloying hot-dipped galvanized steel or by electro deposition. Stelco Inc. produces a thermally alloyed Zn-Fe alloy-coated steel, which is mechanically wiped to remove free zinc.A more extensive use of Zn-Fe alloy-coated steel has been predicted for unexposed autobody and structural part applications, since this material is characterized by good spot weldability and formability, and provides superior corrosion resistance under automotive primers.This investigation has examined the coating composition, corrosion resistance, spot weldability and formability of Stelco's Zn-Fe alloy-coated steel and found its properties to be similar to those of Zn-Fe alloy-coated steel produced by post coating annealing.IntroductionRecently, there has been increased automotive interest in galvanneal, which is characterized by good spot weldability, good paintabilityt and good corrosion resistance when primed. Stelco produces a thermally alloyed zinc-iron coated sheet product similar to galvanneal. However, this product is produced by mechanically wiping the free zinc from the surface of hotdip galvanize to expose the underlying zinc-iron alloy.The surface of Stelco zinc-iron alloy-coated sheet is matte gray and has longitudinal streaks which result from contact with Kevlar wipers during production (Fig. I). This paper describes the coating composition, corrosion resistance, weldability, formability and surface appearance of Stelco zinc iron alloy coatings and, wherever possible, compares these properties to those of galvanneal."

Jan 1, 1987

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By B. J. Moore

This publication contains analyses and related source data for 269 natural gas samples from wells and pipelines in 18 States. All of the samples were obtained and analyzed during, calendar year 1979 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-one previous publications have presented tine results of 11,883 gas analyses made prior to 1979. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source

Jan 1, 1980

By C. A. Hesse

The Quartz Hill Molybdenum Project, In Southeast Alaska, was the first mining project to attempt the permitting of a submarine tailings disposal system in the United States, since the passage of the National Environmental Policy Act of 1969 and the Clean Water Act of 1977. Over $20 million was spent by the project developer in baseline data gathering and In funding the preparation of the four Environmental Impact Statements and other environmental documents required at various stages of the project between 1977 and 1988. Because of the timing and a unique set of environmental, legal and regulatory requirements which applied to this project, innovative approaches were developed. This report describes those requirements and the developments, and gives a full historical account of the campaign for permitting submarine tailings disposal at Quartz Hill, until denial of the NPDES permit application by EPA in September 1 990. The extensive studies done for Quartz Hill suggested that under certain conditions the selection of submarine tailings disposal can be the overall environmentally preferred alternative for a mining project. The Quartz Hill story illustrates the complexity of the existing permitting structure and paints out the desirability of rationalization to achieve a more effective system.

Jan 1, 1993