Search Documents

By R. H. Lien

The Bureau of Mines has conducted research on a flue gas desulfurization (FGD) process as part of its goal of minimizing the undesirable environmental impacts associated with sulfur dioxide (S02)-bearing waste gases. This FGD process, referred to as the modified citrate process, involves absorption of S02 in a buffered citric acid solution. The absorbed S02 is subsequently stripped from the solution using steam, which regenerates the solution and produces a wet S02 product. This product can be further processed to make sulfuric acid or liquid S02. Economic evaluations showed the process to be expensive when the stripper was operated at or near ambient pressures because of the large amounts of steam required for solution regeneration. Research was directed at reducing steam consumption in the stripper. The effect of stripper pressure on steam consumption was investigated. A process research unit (PRU) was operated with the stripper pressurized in the range of 5 to 150 psig. Test results showed that steam consumption decreased with increased stripper pressure. For example, when operating the PRU stripper at 150 psig, 4.1 grams of steam per gram of S02 was required to remove 90 pct of the S02 from a 1.0-vol-pct-S02 gas. This compares to 7.1 grams of steam per gram of S02 required for 90-pct S02 recovery at 5 psig.

Jan 1, 1982

By M. Sibanda

The diffusion of carbon in Co-5% Fe alloy was studied in a belt-type pressure system at temperatures of up to 1330°C and press loads or nominal pressures of 7 020 tons or 42±3 kbar. Under these conditions, this alloy is in the solid state. Discs of graphite and prealloyed Co-5%Fe were used to make up the diffusion couple. The diffusion coefficient increased with increasing press load due to the tendency of the low density graphite to dissolve in the metallic phase reducing the overall volume and increasing the density of the system. Furthermore, inhomogeneous plastic deformation may have promoted diffusion by creating defects in the alloy. Diffusion couples treated at atmospheric pressure exhibited graphite particles in the metal, while those treated at high pressures exhibited carbide in the form of Widmanstatten laths. Carbon analyses indicated increased carbon solubility with increasing pressure. This was confirmed from calculated high-pressure phase diagrams.

Jan 1, 2005

By Robert Jakiel

The following paper is being presented to provide a basic understanding of the equipment and procedures used in multi-auger deep soil mixing as part of the program for the Deep Foundations Institute (DFI) Deep Soil Mix Seminar. The paper is written as a summary of the author's experience using multi-auger deep soil mixing equipment while working with SMW Seiko, Inc. on several east coast projects in the United States, particularly the soil-cement mixing for the soil stabilization of the Fort Point Channel area in Boston, Massachusetts, one of the largest and most difficult soil mixing projects completed thus far in the United States. The summary provides a brief summary and insight into some of the operational aspects of the equipment and procedures, and some of the important considerations when using multi-auger deep soil mixing. This paper is intended for use by both the contractor and the designer involved in selecting appropriate soil mixing equipment and procedures for various types of soils, depths or applications, or for a better understanding of the operational aspects, potential benefits, and impacts that the performance criteria may have on the operational capabilities of the soil mix equipment, when specifying multi-auger soil mixing for a particular project. Prior to reading this article it is important to become more familiar with the various acronyms and terminology used in soil mixing technology. A Definitions section has been provided at the end of the paper that will help the reader become more familiar with some of the terms used throughout this paper.

Jan 1, 2001

By Charles Taschereau

The statements made in this presentation contain certain forward-looking statements concerning potential developments affecting the business, prospects, financial condition and other aspects of Canada Lithium Corp. The actual results of the specific items described in this presentation, and the company?s operations generally, may differ materially from what is projected in such forward-looking statements. Although such statements are based upon the best judgments of Canada Lithium Corp. management as of the date of this presentation, significant deviations in magnitude, timing and other factors may result from business risks and uncertainties including, without limitation, the Company?s dependence on third parties, general market and economic conditions, technical factors, the availability of outside capital, receipt of revenues and other factors, many of which are beyond the control of the Company. Canada Lithium Corp. disclaims any obligation to update information contained in any forward-looking statement. Toronto Stock Exchange: CLQToronto CLQOTCQX: CLQMFOTCQX: CLQMF

May 1, 2011

By Andre Vervoort

Falls of ground, such as falls of roof and sidewall collapses, are a major cause of fatalities and injuries in South African collieries. Based on information obtained from the accident reports of the various Chief Inspectors of nines, a statistical analysis was conducted covering the period 1970 to 1988. This study shows that the volume of rock in a fatal fall of ground is often quite small. In intersections, fatal falls are on average larger than in roadways and at the face. It was also found that in 36 % of all fatal falls of ground no temporary or permanent support was installed at the site of the accident.

Jan 1, 1990

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

By D. Imeson, T. Grammatikopoulos, G. Pearse, M. Aghamirian, C. Mohns

"Spodumene mineral is a source of lithium for lithium ion batteries. Thus, the production of a spodumene concentrate with an approximate grade of 6% Li2O is targeted. Traditionally, spodumene is concentrated by froth flotation using fatty acid as the collector. Amine collector can also be used to float mica ahead of spodumene as required or feldspar from the spodumene tailings. Slimes have a negative effect on spodumene flotation and they are commonly separated by scrubbing and de-sliming prior to spodumene flotation. The main losses in spodumene flotation typically occur in cyclone overflow, scrubbing slimes, spodumene flotation tailings and mica concentrate. In recent years, dense media separation (DMS) is the main concentrating process in Australian spodumene operations. In these operations, DMS is efficient at generating coarse grain concentrates and rejecting large portions of silicate gangue, thereby directly reducing the milling cost. The ore should be crushed to 3/8” or coarser while further crushing is possibly necessary on the middling particles to scalp further spodumene. The DMS feed should be classified to remove fines (typically -0.5 mm particles). The final middlings and undersize fractions could then be processed by flotation. The main requirement in DMS operations is to have good spodumene liberation at relatively large grain size. This paper reviews the most significant DMS and flotation parameters in spodumene beneficiation. The treatments of different minerals in the spodumene ore are also addressed.INTRODUCTION A number of laboratory/pilot plant programs have been recently conducted at the SGS Lakefield site, sponsored by different clients. The main objective has been to develop a process flowsheet to generate a spodumene concentrate containing 6.0% or higher Li2O (~75% spodumene) suitable for producing lithium carbonate by a hydrometallurgical process. Depending on spodumene liberation size, dense media separation (DMS) can be an attractive option to produce a final high grade concentrate and to reduce the mass to be treated in the flotation circuit. In such a case, crushing would typically be performed in stages, with DMS separation to recover a spodumene concentrate and reject gangue minerals following each stage. DMS middlings and -0.5 mm fines can be processed by flotation to further recover spodumene. In the flotation process, coarse stage grinding minimizes the grinding cost and formation of slimes. In the majority of cases, a grind size (K80) of approximately 200 microns is sufficient for flotation. After primary grinding, mica, if present in an appreciable amount, should be floated to minimize interference with spodumene flotation. Desliming after scrubbing and high density conditioning are the key process operations prior to spodumene flotation. Spodumene can then be floated from silicate gangue minerals with a fatty acid or a mixture of fatty acid and petroleum sulfonate at slightly alkaline pH. Subsequently, feldspars can then be floated from the spodumene tailings."

Jan 1, 2012

By Edmund J. Cardoza

The paper describes the design, construction and quality control aspects of the installation of a cement-bentonite (CB) cut off wall to impede seepage through a flood control dike. Special emphasis is placed upon the development of a proper specification, distinguishing the CB method from the Soil-Bentonite technique. The importance of the pre-construction laboratory testing program and field quality control procedures is emphasized by the fact that the in-place properties and characteristics of the CB cut off may not be known until after a majority of the work is complete. Sections are included which describe the construction method, the specialty equipment and personnel requirements and the quality control/quality assurance aspects of the project.

Jan 1, 1992

By John F. Gamble

Amphiboles are hydrated mineral silicates five of which occur in asbestiform habits as asbestos grunerite (amosite) asbestos, riebeckite (crocidolite) asbestos, anthophyllite asbestos, tremolite asbestos and actinolite asbestos] and non-asbestiform habits (grunerite, riebeckite, anthophyllite, tremolite and actinolite). The asbestiform varieties are characterized by long, thin fibers while non-asbestiform varieties such as cleavage fragments form short fibers with larger widths. The U.S. regulatory method for counting asbestos fibers (aspect ratio [>]3:1, length [>]5 µm) does not distinguish between asbestos and cleavage fragments. The method biases toward increased counts of non-asbestiform cleavage fragments compared to long, thin asbestos fibers. One consequence of this regulatory approach is that workers can be erroneously classified as exposed to concentrations of asbestos (asbestiform amphiboles) above the U.S. 0.1 f/mL exposure standard when in fact they are not exposed to asbestos at all but non-asbestiform amphibole cleavage fragments. Another consequence is that the known carcinogenic effects of asbestos may be falsely attributed to non-asbestiform amphibole cleavage fragments of the same mineral. The purpose of this review is to assess whether amphibole cleavage fragments pose the same risk of lung cancer and mesothelioma characteristic of amphibole asbestos fibers. We identified three groups of workers exposed to non-asbestiform amphiboles: two groups exposed to grunerite (Homestake gold miners and taconite miners) and one group exposed to industrial talc containing non-asbestiform tremolite and anthophyllite in St. Lawrence County, NY. In addition to assessing strength of association and exposure?response trends in the non-asbestiform amphibole cohorts, comparisons were also made with cohorts exposed to the asbestiform counterpart (positive control) and cohorts exposed to the mineral (e.g. talc) that does not contain amphiboles (negative controls). The cohorts exposed to non-asbestiform amphiboles had no excesses of lung cancer or mesothelioma. Similar results were observed in the negative control groups, in stark contrast to the excess risks of asbestos-related disease found in the asbestos cohorts. The only possible exception is the twofold increased risk of lung cancer where exposure was to industrial talc containing cleavage fragments of tremolite and anthophyllite. However, this risk is not considered attributable to the talc or amphibole cleavage fragments for several reasons. A similar increased risk of lung cancer was found in Vermont talc workers, studied in the same time period. Their exposure was to relatively pure talc. There was no relationship between lung cancer mortality and exposure measured as mg/m3 years and years worked. A case?control study reported that all the lung cancer cases were smokers (or former smokers) and attributed the excess to smoking. There were two mesothelioma cases among the NY State talc workers exposed to cleavage fragments of tremolite and anthophyllite, but talc is not a plausible cause because of too short latency and potential for previous asbestos exposure. The positive controls of tremolite asbestos and anthophyllite asbestos exposed workers showed excess risks of both lung cancer and mesothelioma and positive exposure? response trends. St. Lawrence, NY talc does not produce mesotheliomas in animals while amphibole asbestos does. In sum, the weight of evidence fully supports a conclusion that non-asbestiform amphiboles do not increase the risk of lung cancer or mesothelioma. ©2008 Published by Elsevier Inc. Keywords: Amphiboles; Cleavage fragments; Lung cancer; Mesothelioma; Asbestos; Non-asbestiform amphiboles; Grunerite; Talc

Jan 1, 2007

By J. M. Weehuizen

Complete details are given of the drilling method by which two shafts were sunk at the new Beatm'x mine of Staatsmijnen in the Netherlands. The nature of the rock strata in the Dutch mining district determined choice of the drilling rather than the freezing method. Data for each step and details of the equipment used are given in the illustrations. Staatsmijnen was founded in 1902 with government financial backing, but it is run as a private enterprise, on a commercial basis, with the normal fiscal obligations. The company now has four mines in operation with annual outputs amounting to 7 1/2 million tons of coal. In 1952 it was determined that a new mine—the Beatrix—would be opened. Details of the shaft-sinking operation are described in this paper. SHAFT LOCATION The coal-bearing carboniferous rock in the Dutch mining district is overlain almost completely by soft water-bearing strata, which at the site of the new shafts are about 1600 ft thick. The sinking of the new shafts through this soft water-bearing overburden (Fig. 1) is a costly and time-consuming affair. From the two availaible sinking methods: 1) Poetsch's well known freezing method or 2) the drilling method of Honigmann-de Vooys, the latter was preferred, not only because of its relative cheapness, under the prevailing conditions, but primarily because by using the drilling process, a special type of shaft lining of steel, concrete, and bitumen could be used. The new shafts, located 330 ft apart, have an inner diameter of 18 ft, 4 1/2 in. The boreholes, which have a diameter of 25 ft and which were drilled through nearly 1600 ft of overburden and some 100 ft of carboniferous, each contain more than 29,000 cu yd—by far the largest in the world. DRILLING METHOD The drilling method is based on the use of mud-flush—a thin mixture of clay and water—to keep the borehole filled during the entire drilling period and during insertion of the lining (Fig. 2). The pressure of the mudflush against the borehole wall is greater than that of the water in the surrounding

Jan 1, 1961

By Osama El-Fiky

There are many types of deep foundations currently being used in the San Francisco Bay Area, one of the most common being driven precast, prestressed concrete (PC/PS) piles. PC/PS piles are frequently selected for use due to of ease of installation, availability, and relatively low cost. Disadvantages of using PC/PS piles are noise, vibrations, pollution, front-end delays due to indicator pile programs, and reduced flexibility. An acceptable alternative to driven PC/PS piles was selected for construction of foundations for the heavy housing and administrative buildings at the San Francisco County Jail #3 replacement project in San Bruno, California. The pile type selected, the Auger Pressure Grouted Displacement (APGD) pile, was chosen to reduce noise, vibrations, installation time, and cost, and to allow for greater flexibility of installed pile lengths. This paper presents a case history of the use of APGD piles that were substituted for driven PC/PS concrete piles for the subject project. Standard and quick loading pile load tests were performed to confirm adherence with the design criteria originally used for the driven PC/PS concrete piles. The APGD piles were found to increase shear strength around the piles similarly to driven displacement piles. In addition, this paper presents the methodology used in monitoring APGD pile installation.

Jan 1, 2002

The Greymouth Coal field is situated on the West Coast of New Zealand's South Island and has been mined for coal for more than 120 years. The area covered in this paper is within the Rapahoe Sector of this field and contains >200 million tonnes of low ash, low sulphur, bituminous rank coal. Paper No 6, presented to the 19th Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy in Christchurch in August 1985 by R G Bowman, explained 'A Geologist's View' of the 'Economic Potential of the Greymouth Coalfield', and describes previous geological assessments of the Rapahoe Sector.

Jan 1, 1989

By James A. Schneider

The successful installation of long piles driven into very dense sands relies on the occurrence of the reduction in local friction with increased pile embedment, a phenomenon known as ?friction fatigue?. The underlying mechanisms controlling friction fatigue are poorly understood, with some design methods including an adjustment for the influence of pile diameter while others do not. This paper back calculates the installation resistance of 0.356m to 2m (14in to 78in) diameter open ended piles driven into very dense sands using wave equation analyses. Cone penetration test data are used to link soil properties to installation resistance. The study illustrates consistent interpretation of a variety of case histories of open ended piles driven in very dense sands using newly developed analysis techniques and normalized parameters. Results provide information on methods for incorporating friction fatigue into drivability studies as well as a discussion of mechanisms related to pipe pile installation resistance in sandy soils.

Jan 1, 2010

"The application of telerobotics to mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa, and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place, a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run?A Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University to investigate these questions and many more through a series of experiments in a telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian College’s eDome. The laboratory supports many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments, and some preliminary results."

Jan 1, 2005

By B Whittaker

The paper examines the role of chain pillars in longwall mining layouts as used in several countries. The application of chain pillars in relation to their expected design role is discussed. An important feature is the specification of the pillar design to meet strata loading conditions as imposed by the mining and geological setting. The paper relates longwall width and chain pillar configurations to pillar size to satisfy anticipated loading and strength expectations. Laboratory work is referred to which examines criteria for pillar stability. Comments are made regarding the application of the findings presented in the paper, to different situations involving the use of chain pillars in longwall and shortwall mining systems.

Jan 1, 1987

By F. Freme

Coal production in the United States reached a record level in 2005, ending the year at 1.03 Gt (1,133.3 million st) according to preliminary data from the U.S. Energy Information Administration (Table 1). Production in 2005 was 19.2 Mt (21.2 million st) higher than the 2004 level of 1 Gt (1,112.1 million st) and surpassed the prior record set in 2001 by 5.1 Mt (5.6 million st). Although total U.S. coal consumption rose in 2005, not all coal-consuming sectors had increased consumption for the year. Coal consumption increased in the electric power sector by 2.2 percent and declined in the other industrial sector, while coking coal consumption decreased slightly.

Jan 1, 2006

During the latter part of 1937 consideration was given to the construction of a; local smelting plant for producing blister copper. Previously copper concentrates had been shipped to the United States of America. The proposition had the advantages of a saving in cost of realization, quicker financial return and reduced dependence on overseas shipping.The smelter was designed by the existing staff, who had difficulty in obtaining data on small plants, particularly on the reverberatory furnace. Construction was started in March, 1938, and the reverberatory was blown in on January 16th, 1939. One roaster had been operating for several weeks prior to this date.While results and operating technique on this new departure in small-scale smelting are barely beyond the experimental stage, it is felt that the experience gained to this time should be recorded to help fill the obvious gap in published information covering plants of this type.At present there are three copper smelters operating in Australia; the other two plants are equipped with blast furnaces.LOCATIONThe new smelter is situated in a position convenient to the concentrator and to the power plant. The site is traversed on two sides by a brick flue, from an old smelter plant, which connects with a 250-ft. stack. This stack and portion of the old flue are used in connection with the...

Jan 1, 1939

Solvent extraction has recently been introduced into Australian hydrometallurgical practice for the production of a high grade uranium concentrate from El Sherana ore by a sulphuric acid leach and solvent extraction process. The solvent is a 5 per cent solution of tri(iso-octyl)amine in kerosene modified with 4 per cent of a long chain alcohol. The stripping reagent is a molar solution of sodium chloride.Preliminary testing for the development of the process showed that the leach liquor was quite amenable to the solvent extraction process and that the equilibrium and rate considerations of both the extraction and stripping steps were very favourable.The industrial plant contains four stages of extraction, three stages of chloride stripping and one stage of secondary carbonate stripping. An internal type of mixer-settler is used for the stagewise contact, the design being based on tests with model equipment.The performance and control of the industrial plant is satisfactory; 99·7 per cent of the uranium is recovered for a loss of 0·3 gallons of kerosene and 0· 4 pounds of amine per 1,000 gallons of liquor treated.INTRODUCTIONThe processing of El Sherana uranium ore from the South Alligator River valley commenced in April, 1959, and thereby introduced into Australian hydrometallurgical practice the unit operation of solvent extraction on an industrial scale. Although there are now some twelve mineral processing plants in the United States and Canada using solvent extraction, its application to the field of primary hydrometallurgy is quite new. Prior to 1956 none of these twelve plants was operating and hydrometallurgical application waslimited to the refining of comparatively high grade uranium compounds and fission products from nitrate and nitric acid solutions.

Jan 1, 1961

By Abraham Lindo

"Blasting plays a key role in hard rock underground mining. It is by nature a violent and destructiveextraction method designed to economically fragment the rock into a suitable size for it to be loaded and hauled as part of the specific mining process while controlling the amount of damage to the surrounding rock mass."

Jan 1, 2016

By H. Jang, Y. Kawamura

Unplanned dilution and ore loss directly influence not only the productivity of underground stopes, but also the profitability of the entire mining process. Stope dilution is a result of complex interactions between a number of factors, and cannot be predicted prior to mining. In this study, unplanned dilution and ore loss prediction models were established using multiple linear and nonlinear regression analysis (MLRA and MNRA), as well as an artificial neural network (ANN) method based on 1067 datasets with ten causative factors from three underground longhole stoping mines in Western Australia. Models were established for individual mines, as well as a general model that includes all of the mine data-sets. The correlation coefficient (R) was used to evaluate the methods, and the values for MLRA, MNRA, and ANN compared with the general model were 0.419, 0.438, and 0.719, respectively. Considering that the current unplanned dilution and ore loss prediction for the mines investigated yielded an R of 0.088, the ANN model results are noteworthy. The proposed ANN model can be used directly as a practical tool to predict unplanned dilution and ore loss in mines, which will not only enhance productivity, but will also be beneficial for stope planning and design.

Jan 1, 2015