Search Documents

By K. S. Mortensen

The softwall mining system is a novel, new method of mining mineral deposits in soft, shallow, nonrock ground conditions. This method can mine the ore layer without substantially disturbing the existing overburden. The softwall mining system consists of machinery that is hydraulically controlled and powered, that can be buried (or used on the surface) to extract the ore or mineral from a layered deposit. The method is essentially an application of the longwall mining concept, modified for loose overburden and ore conditions, combined with hydraulic mining.

Jan 1, 2003

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002

By T. W. Peglas, J. Doherty, R. A. Day

The South East Transit Project is a $520 million project in Brisbane, Australia which includes the construction of a 32 km Busway to access the south-eastern suburbs. Close to the centre of Brisbane, tunneling techniques have been used to minimise surface disruption. This paper describes some of the features of the longest driven tunnel on the project, the Vulture Street Tunnel. The Busway is a two lane expressway for buses which requires a 10.2 m finished width and a 12.6 m excavated span of driven tunnel. The Vulture Street Tunnel carries the Busway at minimal cover beneath the operating Vulture Street Railway Station, beneath a three storey office building and beneath the roadway to the Mater Hill Busway station. Halfway along the route, a Y-junction has been constructed to enable future connection with a light rail route. Key features in the design and construction of the Vulture Street Tunnel include: Use of canopy tubes to drive a 12 m wide tunnel beneath operating railway tracks with less than two metres of cover in highly weathered rock. Underpinning the office building in the route of the tunnel construction from within the building carpark. Construction of a 24 m span Y-junction with 7 metres cover of weathered and faulted rock. Use of predictive analysis as an adjunct to traditional back analysis to estimate the tunnel settlements from pressuremeter test results. This paper describes the design methodology with particular reference to settlement prediction, as well as construction innovations used to complete the tunnel. This paper will be of interest to all designers who have to create large spans in minimal cover in weak rock in urban areas and who have to predict the settlement

Jan 1, 2001

By Blaisdell J. L, MacPherson G

The present communication records the results of a research investigation conducted in the Porcupine Gold Mines in Timmins, Onto. Soon after silicosis became a compansable disease in Ontario under the Workmen's Compensation Act in 1926, the attention of mine operators and physicians was drawn sharply to the prevalence and importance of this condition in the mining industry. A number of examining centres were established in Northern Ontario by the Workmen's Compensation Board, and the yearly X-ray examination of miners was made compulsory.Although working conditions were soon improved, the mining industry realized that they were confronted by a problem demanding basic research for its final solution. The late Sir Frederick Banting had, for a number of years, been interested in silicosis, and it was upon his suggestion that an experimental investigation was undertaken at the McIntyre-Porcupine Mines Ltd., Schumacher, Ont., in November, 1932. A preliminary report of this investigation was published in 1937 by Denny, Robson and Irwin and a further report by the same authors in 1939.Accepting the theory that silica exerts its injurious effect upon animal tissue through a slow transformation into silicic acid in the presence of body fluids; these authors assumed that if the solubility of the silicious material retained in the lung could be sufficiently reduced, the usual fibrotic response would be modified or would not occur. A search was therefore undertaken for some non-toxic compound that would fulfil this purpose. After investigating ma:qy substances, Denny and Robson discovered in 1936 that the presence of small amounts of aluminum powder almost completely inhibited the solubility of silicious material in vitro. An intensive study of the mechanism involved later showed that the reduction in solubility was due chiefly to a coating of the silica particle with a thin film of a gelatinous hydrated alumina which on drying formed the crystalline alpha aluminum monohydrate boehmite (AI203.H20). The presence of this absorbed layer on the surface of the quartz was indicated by -staining it with aurin (ammonium salt of aurin tricarboxylic acid) and proved by Germer and Storks by means of electron diffraction patterns.Inhalation experiments with animals were at once begun, using pure quartz dust with and without aluminum powder. (See original communications.) These observers showed that while typical silicosis was produced in about 5 months in the control animals receiving silica dust alone, the...

Jan 1, 1945

By Chris Mark

Successful longwall mining requires a stable tailgate entry. Gate entry performance is influenced by a number of geotechnical and design factors, including: - Pillar size and pillar loading; - Roof quality; - Floor quality; - Entry width; and, - Artificial support (primary and secondary). This paper describes a comprehensive, practical, design methodology, based on statistical analysis of a nationwide data base of longwall ground control experience. Geotechnical surveys were conducted at 44 U.S. longwall mines, and underground observations of site geology, entry conditions, and support design were recorded at each mine. The observations were combined with discussions with mine personnel to identify 69 longwall gate entry designs as satisfactory, unsatisfactory, or borderline. Only conventional longwall designs, in which the pillars are expected to carry the full abutment loads, were included in the data base. Designs which employed yield pillars only were excluded. The case histories were characterized using five descriptive parameters. Pillar design was described by the Analysis of Longwall Pillar Stability Factor (ALPS SF). A major new contribution is the Coal Mine Roof Rating (CMRR), a rock mass classification system that quantifies the structural competence of bolted mine roof. Other quantitative measures were developed for primary support, secondary support, and entry width. Multivariate statistical analyses indicated that in 84% of the case histories the tailgate performance could be correctly predicted using just ALPS and the CMRR. Most of the misclassified cases fell within a very narrow borderline region. The analyses also confirmed that primary support and gate entry width are essential elements in successful gate entry design. The relative importance of the floor and of secondary support could not be determined from the data. Based on these results, a simple equation was developed to guide the design of longwall pillars and gate entries: ALPS SF,, = 1.76 - 0.014 CMRR Where: ALPS SF, = ALPS SF suggested for design. Guidelines for entry width and primary support density, as related to the CMRR, are also provided.

Jan 1, 1993

By Morabito J, Harrop D. W

Uranium exploration was commenced in 1973 and carried out at a regional scale over a wide area of the northern part of the Camarvon Basin of Western Australia by Minatome Australia Pty Limited and their joint-venture partners. As a result, pervasive uranium mineralization has been found in the Cretaceous sandstones near Manyingee Hills in the Onslow Region, which were probably deposited in a near-shore, fluvia deltaic palaeo-environment.Mineralization is generally found in poorly sorted argillaceous sandstones and siltstones near redox fronts formed by oxidizing waters circulating in reduced sediments. The principal minerals found in the two Manyingee deposits delineated so far are coffinite, uraninite with associated pyrite in the reduced zones, and phosphuranylite, siderite and limonite in the oxidized zones. The presence of dissolved uranium in the superficial aquifers, of secondary uranium minerals as coatings on granitic rocks, and of recent uranium-bearing calcrete sediments, suggest that the whole Cretaceous-Precambrian system has been subjected to the formation ofroll-front type uranium deposits since the Cretaceous. Continuing exploration is locating additional uranium occurrences. The deposits outlined so far are being evaluated for their amenability to in situ leaching tests planned for 1982-1983.

Jan 1, 1981

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

By Liyuan Chai

In this study, spent grain was used as an adsorbent for the removal of Hg(II) from aqueous solutions, the process parameters such as contact time, solution pH, adsorbent dose, and initial Hg(II) concentration were studied in batch experiments. The initial adsorption process was fast, 91.08% of adsorption occurred within 5 min and equilibrium was reached at around 30min. Adsorption process was found to follow pseudo-second-order kinetics. The equilibrium data were better fitted to Langmuir isotherm than Freundlich isotherm with the maximum adsorption capacity 41.36 mg/g. The structure and component of spent grain before and after adsorption of Hg(II) were investigated using scanning electron microscope(SEM) and energy dispersive X-ray analysis(EDAX), these analysis also confirmed the adsorption of Hg(II) onto spent grain. The results indicated that spent grain had potential as a new inexpensive adsorbent for Hg(II) removal from aqueous solutions.

Jan 1, 2009

GOLD has played a part in the development of Australia. The total yield exceeds SIX hundred million pounds sterling, while the glamour of gold-mining and the unfailing demand for the product have enhanced its influence. The production is still considerable, but the yield is less than one-quarter of that twenty years previously, while the number of men employed has dropped from 70,000 to 11,000. Not only has there been a marked decline in production, but it is anticipated that thisdecline will continue, and continue more markedly. It is therefore desirable to ascertain the causes of the decline and inquire into means for diminishing or preventing it.The problem under discussion is far from being only local. Finlay states: The grand feature of the history of the business has been the progress of an economic cycle unfavourable to gold milling. The USA yield fell from $101,000,000 to $44,000,000.South Afriea has for some time produced one-half of the world's gold; yet in the Mining and Scientific Press of 11th February, IH22, General Smuts is quoted as saying that if the premium disappeared entirely 24 out of 34 mines would shut down. The solution, however, might be either general eg, a great advance in the metallurgy of gold; or local eg, a bonus; but before discussing any of the proposed solutions it will be advantageous to review the situation.STATISTICS OF THE PAST AND PRESENT PRODUCTION OF THE WORLD AND OF AUSTRALIAThe inquirer soon finds that there is a good deal of uncertainty, and that much care is needed in collating figures. In some cases a considerable part of the output is not officially reported, and returns...

Jan 1, 1924

By C. L. Schneider, C. O. Gomes, R. P. King, J. A. Finch, D. Lin

Discussion is presented by Prof. King and Dr. Schneider of the paper by Lin, Gomez and Finch published in Trans.IMM C, vol.104, 1995, p.C155-C161. They conclude that the correction procedures used for simulated observations of simulated capped spheres are not reliable when applied to mineralogical data and that their relative ranking should not be extrapolated to other situations. Properly regularised solutions obtained with the use of appropriate kernels can be safely used for routine mineral liberation work and can be calibrated accurately against real mineralogical samples in the laboratory

Jun 19, 1905

By M Wilson, D Whiteman, P Kuiper, S Talu, G Watt, A van As

Once the draw process has begun in a block cave, it is very difficult to identify which regions of the cave have successfully propagated, where the caved material is flowing from and where it is flowing to. The uncertainty around cave flow increases as the cave is drawn and can be further compounded by poor draw control practices. These uncertainties make it difficult to plan effective draw strategies to control dilution, as flow model predictions tend to gradually diverge from the actual state of the cave. There have been documented occasions where observed caving phenomena, such as muck pile surface rilling, could not be reproduced with the cave flow models of the time. The ultimate consequence of cave flow uncertainty is generally manifest as higher dilution and lower grades.In order to measure the real-time flow of caved material within an active block cave, CRC Mining and Elexon have developed, together with Rio Tinto, a cave flow monitoring system called Cave Tracker, which is being trialled at Argyle Diamond Mine (ADM) in Western Australia. The Cave Tracker system at ADM comprises electronic ‘beacons’ that have been installed down long HQ diameter drill holes located above the extraction level. As the cave-back propagates and the rock mass fragments, beacons are released into the muck pile and flow along with the caved material to the drawpoints below. At Argyle, the beacons are configured to emit a signal every three days. These signals are picked up by detectors installed on the extraction and undercut levels, allowing the positions of the beacons to be determined.By examining the real-time material flow in different regions of the cave, flow mechanisms can be better defined. Draw control strategies can then be actively tailored to manage the current state of the cave. Thus, previously undetectable indications of excessive rilling, rapid cave propagation, cave stall, air gaps and dilution entry can now be identified early and assessed continuously as the cave progresses. For the first time it is possible to amend draw strategies based on measurements from inside and outside of the fractured zones, allowing caves to be managed more effectively.CITATION:Whiteman, D, Talu, S, Wilson, M, Watt, G, Van As, A and Kuiper, P, 2016. Cave Tracker flow monitoring system installation at Argyle Diamond Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 479–488 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The relationship between neural network (NN) performance and the parameters that form the architecture of the neural network is complicated. This paper studies an issue that is still controversial—the effect of the number of neurons and number of hidden layers on NN performance. This paper tests if the above parameters affect network performance when the NN is trained according to the quick stop strategy. It was determined that the number of neurons did not have any effect on the NN performance for a single layer or a double layer network. It was also found that the training error and calibration error could be poor indicators of the prediction correlation coefficient.

Jan 1, 2003

By Robinson KJ

Education in Australia now has to respond to a very wide political and policy agenda. The political emphasis is upon increasing participation and retention rates with a view to greater graduation rates in `high-tech' disciplines. There is an implied linkage between `education' and `economic well-being'. Our argument is that equalitarianism in education tends towards mediocrity. In this context many Geoscience educators view the future with pessimism. The argument is that science has been `sold short' and needs revitalising. We contend that Geoscience coursework should be a feature of both secondary and tertiary education in Australia. To this end we propose six policy initiatives to increase the content of Geoscience in education programmes.

Jan 1, 1989

By Frederick W. Slack

This paper will discuss the inherent value engineering associated with the design and construction of approximately 184,000 SF of anchored tieback wall, installed as part of the widening and drainage improvements for KY9 in Campbell County, Kentucky. The total project is 2.2 miles in length. The anchored walls, excavation grading and drainage total to a complete project cost of $28.4 million. This is one of the largest design-build projects undertaken by the Commonwealth of Kentucky. It also features another first for the Transportation Cabinet - the general contractor is responsible for quality control/quality assurance. The project is located just south of Cincinnati, OH and is situated along the east bank of the Licking River. The slopes along this stretch of the river have had a long history of movement and instability. The Kentucky Transportation Cabinet advertised the anchored wall portion of this project to be designed and constructed by pre-approved specialty contractors. The Transportation Cabinet provided the basic design parameters to each specialty contractor. Aspects to be discussed include the site and project history, previous attempts at slope stabilization along existing KY9, the technical proposal and bidding process, and the actual design and construction.

Jan 1, 2003

By Lawrie D. C

Finely ground beryl was decomposed by mixing with ground limestone and soda ash and heating at 900°C for 4-6 hr. The sintered mater:al was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hr. The liquor containing Be, AI, Fe and other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either by filtration or bydecantation washing.The clarified leach liquor was first treated to remove Fe+++ by contacting with a primary amine-kerosene solution in 2 countercurrent stages. The iron free liquor was then passed to a 4-stage counter-current extraction unit where it was contacted with O·5M di- (2 ethyl hexyl) phosphoric acid (EHPA) in kerosene. Under the operating conditions, 99 per cent of the Be and 7 per cent of the Al was extracted.The Be and Al were stripped from the organic phase by sodium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipitatedas Be(OH)2 by heating the alkaline solution to 90°C, the Al remaining in solution. After filtration and washing, the Be(OH)2 could be ignited directly to BeO at about 1000°C or used as a feed to further purification stages if required.A small counter-current extraction unit was operated continuously using liquor derived from the sintering and leaching stages. Dataobtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precipitate contained more than 99 per cent BeO.INTRODUCTIONIn 1958 an investigation was commenced into the recovery of beryllium oxide from beryl, as part of a programme to utilize mineral resources of South Australia. A survey of the literature indicated that little work had been done on direct solvent extraction of beryllium from aqueous liquors, so it was decided to apply the experience gained in this field in uranium processing to the current problem.Preliminary extraction tests on solutions of beryllium...

Jan 1, 1965

Rock engineering has now been practised as a discipline for about50 years, and many sophisticated methods of analysis for use in rock engineering design have been developed. However, analysis is only a tool for use in engineering design, and rock masses are often so complex that realistic modelling of them, even with sophisticated methods of analysis, is impossible. At the other end of the scale, rock mass classification methods have been developed to quantify the rock mass. These ?numbers? are now widely used for assessment of stability of underground and surface excavations in rock, for the determination of rock support requirements, and for the estimation of rock mass strength and deformation properties. In considering these areas, the two concepts?design, and prediction of behaviour?will be dealt with. The discussion will be introduced by a consideration of the characteristics of the rock mass, which will highlight the variability in its properties and hence the uncertainty in the behavioural parameters. Examples of real projects will be used to illustrate the discussion.

Jan 1, 2003

The production of sulphuric acid at Port Pirie by the contact process began in March 1924 with the commissioning of the Electrolytic Zinc Co.'s roasting and acid plant. This plant, operated by B.H.A.S. Pty. Ltd. on behalf of the E.Z. Co., continued to produce sulphuric acid from the gases evolved when roasting Broken Hill zinc concentrate in mechanically rabbled furnaces until September 1954, when the plant was closed down.In this peri9d of approximately 30 years some 600,000 mono tons of 98·5 per cent sulphuric acid was produced, most of which was used for fertilizer production at Wallaroo and Port Adelaide. During World War II 14,400 mono tons of the above was produced in the form of 20 per cent Oleum and railed to the Salisbury Munitions Factory for use in the production of nitro-glycerine, gun-cotton and T.N.T.In the early post-war period various ways of converting at least some of the sulphur in the gases' discharged to atmosphere from the lead sintering plant were considered until, in 1949, it was decided to erect a modern contact acid plant. Much work remained to be done on the roasting plant to produce a gas of suitable grade for the contact process and also on the design of a purification section suitable for the treatment of D.L. gases.The acid section itself, however, was largely of conventional design and it was therefore decided that this would be erected first. To it was then attached a sulphur-burning section to allow it to operate as a "hot gas" brimstone acid plant until the roasting and gas purification plants had been designed and erected. In this way the urgent need for sulphuric acid in the fertilizer industry would be relieved, to some extent at least, as soon as, possible.

Jan 1, 1956

By H. F. Yancey

About 65 percent of the more than 400 million tons of coal produced annually in the United States is mechanically cleaned to remove the inorganic impurities before being sent to market. The impurities, principally shale and clay with some pyrite, average about 20 percent of the raw coal treated. Nearly 95 percent of the tonnage is treated by wet processes, in which water, suspensions of solids in water, or occasionally calcium chloride solutions are employed. Difference in density of coal and impurity is the basis of these processes. Of major importance in the separation is the competency of the impurities, that is, the resistance of the impurities to size disintegration in water. In general, the impurities are more resistant in geologically older coals or those in effect made older by metamorphism. If the impurities suffer reduction in particle size when immersed in water, the separation of organic from inorganic material becomes more difficult, Recently the Scientific Department of the National Goal Board (Great Britain) undertook fundamental research into the interaction of shale and water and also developed an empirical method of assessing shale breakdown or disintegration. 6

Jan 1, 1962

By F. A. Seward

A1though the expanding Eltran1 configuration has been used in induced polarization exploration for several years, there has been little application of this method to straight resistivity problems. A comparison of results of resistivity exploration by this technique versus those obtained from Wenner configuration surveys reveals a number of advantages in interpretative resolution as well as in field operation. The application of electrical resistivity to ground-water exploration is well known.= In the past a major portion of this work has been accomplished by use of one or more variations of a technique employing the Wenner3 electrode configuration. With the introduction of the frequency domain technique of induced polarization measurements, used primarily in the exploration for disseminated sulfide deposits, there arose the need for an electrode configuration by which potentials could be measured externally to the current electrode spread in order to minimize coupling between current sending and potential receiving circuits. It was also deemed desirable that the configuration would provide information laterally along profile as well as with depth. To reach these objectives the expanding dipole-dipole configuration (which probably first was used in the electrical transient method of exploration and from which the name 'Eltran' was derived) has been adapted to induced polarization exploration. The author has successfully applied the same techniques

Jan 1, 1963

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Selective-reductive leaching of manganese from low-grade manganese ore using tannic acid as a reductant in acidic media was demonstrated by XRD, SEM-EDX characterization, and batch leaching studies at room temperature. The pH change in the liquid phase before and after leaching revealed that selectivity of manganese over iron was due to the hydrolysis of iron. The acidity in the liquid phase during leaching was dictated by two mechanisms: proton-consuming reaction (manganese oxide reduction by tannic acid) and proton-producing reaction (ferric ion reduction by tannic acid to produce ferrous ion). Based on the leaching studies, the more prevalent reaction between these two was determined by initial leaching conditions: tannic acid concentration, sulfuric acid concentration, liquid-solid ratio, temperatures, and agitation time. Kinetic studies revealed that maximum recovery was attained within 6-h agitation, which indicated a product layer diffusion process.