Search Documents

By Sam Palombo, James José Varela

"Washing can be defined as the process used to eliminate or reduce the dirt (presence of fines or slimes) of one material. It is also the basic and oldest process applied to ore preparation for further concentration. This process, in combination with commnution and screening, form the so called washing plant and in many cases produce end products. This work describes the factors that influence the performance of the washing process and main washing technologies used in the mineral processing industry.The Hydro-Clean represents, since 1998, a state of the art technology in this area and is comprised of one of the most innovative solutions developed at HAVER & BOECKER. HAVER & BOECKER design and manufacture technology for mining and related industries. Today the Hydro-Clean is manufactured and sold throughout the Haver Screening Group (HSG) which is comprised of HAVER & BOECKER Maschinenfabrik Münster, HAVER & BOECKER Latinoamericana – Brazil and W.S. Tyler Canada.The Hydro-Clean is a washing technology based on utilization of high pressure water jets. To follow we will discuss how the Hydro-Clean’s different modes of operation result in several advantages related with mine waste reduction, recovery of saleable product, lower capital costs, superior washing results, less stress for the material, a wider range of application and less maintenance cost. Aside from these positive factors, its lower operation costs related to the consumption of energy and water are presented. It is important to note that the quantities, tonnages, data and management concepts presented in the paper are accurate for the time of writing and are subject to change and modification as operations progress."

Jan 1, 2009

By Robert J. Rothwell

Underground mining of coal by longwall mining methods has not been a predominant technique in Ohio. To date, only five mines in the state utilize this method, however, the technique has sparked a certain amount of controversy. As a mining technique, longwalling was introduced into southeastern Ohio in the early 1970's but it did not attract public attention until the mines began moving into privately held surface lands. This occurred coincidentally at about the same time that the state of Ohio began to regulate the environmental impacts of underground mining. Prior to the passage of the Surface Mining Control and Reclamation Act in 1977, (SMCRA), Ohio's reclamation law, Chapter 1513 Ohio Revised Code (O.R.C. 1513) did not regulate underground coal mines. As a result of SMCRA, the Ohio Statute was amended in 1978, to include regulation of the surface effects of subsidence. The inevitable result was that existing mines were immediately subject to regulations that were not considered during the initial mine planning process. (For an excellent survey of Ohio Laws that deal with coal mine subsidence, see Zima, 1985. ) The problem faced at that time by both the coal industry and the Ohio Division of Reclamation (the agency within ODNR charged with implementing O.R.C. Ch. 1513.1, was that of attempting to superimpose permitting requirements, and design performance standards onto mines that' had been operational for a number of years.

Jan 1, 1986

By M. J. Beus

A shaft is truly the "lifelinen of an underground mine. Damage to the shaft lining and guides as a result of ground movement can result in serious loss of production and extensive and continual repair. In some mining districts, annual shaft repair and maintenance costs resulting from high rock stresses and excessive displacement are in the millions of dollars per year. For many years, the Bureau of Mines has conducted research to characterize the rock mass and to develop structural guidelines to improve the design of accessways in deep mines. Much of this work has centered on determining the in situ conditions that affect the structural stability of shafts in the Coeur d'Alene Mining District of northern Idaho. Recent work by Beus and Board (1984) has concentrated on measuring the rock and support behavior during sinking of the Silver Shaft at the Lucky Friday Mine. These results are currently being used as a comparative data base for further basic research as well as to establish structural design criteria. The factors affecting the deign and structural stability of deep mine shafts are numerous. A design approach that use field data as input and directly compares field measurements with numerical models can validate the procedure and provide realistic design criteria. Naturally occurring "fixed? conditions such as magnitude, direction, and ratio of in situ stresses, geologic environment, and physical properties and constitutive relationships of the rock mass ere obviously basic to numerical modeling.

Jan 1, 1989

By K. F. Unrug

In the paper a numerical modeling method is used for evaluation of a roof support system, which is commonly used in the US coal industry. The effectiveness of mechanical roof bolting with or without, header boards and steel straps are compared. This analysis takes into account the response of a shaly roof to changing environmental conditions in mines related to the seasonal changes in temperature and humidity of the intake air. Discussed are principles of roof support in coal mines and based on them a critical evaluation of header boards interaction with bolts and roof itself is carried out. Header boards create a soft inclusion within a much more stiffer system comprising bolt-rock. As an alternative to header boards, steel straps are analysed and corresponding results are presented. It is demonstrated that application of steel strap is beneficial from the stand point of stress distribution and maintaining tension on roof bolts. The laboratory investigations and modeling work previously undertaken by the authors, clearly indicate the detrimental effect of header boards on effectiveness of roof bolting. There are significant practical implications of the research considering that header boards are commonly used in mines. This practice has been probably originated from the wooden support used by mining in "pre-bolting era?, and it has stayed with coal mining based on tradition more than principles of engineering design. It is demonstrated that header board$ are detrimental and actually contribute to development of roof problems.

Jan 1, 1989

In recent years it has been more and more recognised that applied geology can be of service to the mining industry, and many mining companies overseas now have permanent geological staff as part of the operating organisation.Most of these companies insist that the geological department must pay for itself by the savings it can make in operating cost, and the growing use of the geologist is proof that such savings are made.The geological problems in every district are different, and a description of the problems and method of attack in a specified district is a useful addition to the literature of mining geology. Very few contributions, from the standpoint of the mining company geologist, have appeared in the Australian literature so that, although the operations of Bendigo Mines Limited are still in the development stage, and its geological work newly established, a description of the routine geological work at Bendigo should beof interest.Although most Bendigo mining companies have not employed permanent geologists, they have utilised geological guidance wherever possible, and a great body of data has grown up. Acknowledgment is made here to the valuable work of the Geological Survey of Victoria, especially the writings of E. J. Dunn, H. Herman, and H. S. Whitelaw, and the maps of Caleb Thomas and H. S. Whitelaw; and also to the work of independent investigators, notably Chief Geologist, Bendigo Mines Ltd.

Jan 1, 1936

By J. B. Fletcher

The Miami mine first started operations in 1910. For convenience, the history of the orebody can be divided into the following categories (Fig. 1): 1) 1910 to 1925: 24.4 million tons of high grade ore, mined by top slicing, sublevel caving, etc. 2) 1926 to 1954: 102 million tons of low grade ore, mined by block caving.

Jan 1, 1961

By C. Kloppers

The aim of this investigation was to reduce the cost of primary steel de-oxidation by substitution of aluminium primary de-oxidation with a practice that uses carbon. The cost of carbon is four times lower than that of aluminium. The application of carbon would directly result in raw material cost savings. Investigations were conducted at Iscor?s Newcastle steel plant on various steel grades. Specific production aspects were emphasized to ensure that the cost savings accrued would not create secondary expenses. These production aspects entailed: ?Yields on de-oxidation elements ?De-oxidation capabilities ?Alloying yields (Mn and Si) ?Carbon-pickup ?Nitrogen-pickup ?Temperature loss during tap ?Steel cleanliness ?Slag morphology. This project proved that carbon de-oxidation, apart from reducing de-oxidation raw material cost due to cheaper raw materials being used and lower consumption rates, resulted in steel that is cleaner and has lower nitrogen concentrations. Carbon primary de-oxidation has been implemented at Iscor?s Newcastle plant on a large range of steel grades, ranging from ultra-high carbon (> 0.60% C) to ultra-low carbon (< 0.03% C) grades. A net saving of between R100 000 and R200 000 per month was achieved.

Jan 1, 2001

By Chuck Edwards

"Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. Over that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin close out the paper.INTRODUCTIONThe roughly oval Athabasca Basin in northern Saskatchewan occupies nearly one third of the surface area of the Saskatchewan Shield. Its sandstone-like deposits lie unconformably on the older basement. The basin hosts many high-grade unconformity-type uranium deposits(Saskatchewan Energy and Resources, 2010) for which the Athabasca Basin is world famous. Uranium production in the Athabasca Basin has come from four mills. In the order of startup these are Rabbit Lake, Cluff Lake, Key Lake and McClean Lake. General data (AREVA, 2010; Cameco, 2010; Denison 2010) for each mill are shown in Table 1."

Jan 1, 2011

Sluiceboxes can provide a much higher concentration ratio than most other gravity concentrators (up to 50 000:1) at very high overall placer gold recoveries (greater than 99 per cent). They are also very reliable, inexpensive and simple to operate. This combination is very difficult to beat and explains why the sluicebox is still the most important placer gold concentrator in northwestern Canada, Alaska and the rest of the world. A sluicebox is a rectangular fl ume containing riffles on matting, through which a dilute (&lt;12 per cent) slurry of water and alluvial gravel flows. Sluiceboxes are actually centrifugal concentrators with settling velocity playing a minor role in gold recovery. Due to their higher density, gold particles tend to segregate to the bottom of the slurry flow where they form a streamline that is diverted by a low pressure zone into a riffle. Under ideal conditions, this ribbon of slurry will be overturned as it flows down the rear of the following riffle and will continue fl owing in a circular path to form a vortex. At the bottom of this vortex, centrifugal and gravitational forces combine to drive gold particles into or beside the matting. To remove the gold concentrates, sluiceboxes are shut down and the riffles and matting are taken apart and cleaned. The slurry velocity provides the energy that powers the vortex. If the velocity of the slurry is reduced through overloading with solids, insufficient water flows or shallow gradients it may not sustain a full size vortex. If the riffles are too close, too far apart, too tall, or if there is not enough energy available to the vortex, the vortex will not be formed properly and gold recovery will be reduced. If the slurry velocity is too high, extreme turbulence and the resulting scouring will also cause gold losses. Testing sluiceboxes with conventional sampling and evaluation techniques is very costly, time consuming and problematic. Most placer gold ores contain a very small number of gold particles in a large volume of pay gravels. Sluiceboxes can lose coarse gold particles. The presence or absence of one of these particles in a tailings sample can lead to high unpredictable errors (nugget effect) even when large sample volumes are processed with care. Every time conventional samples are upgraded, additional errors are introduced due to the inefficiency of recovery equipment. Nuclear tracer tests are more accurate, faster, cheaper and safer than conventional sampling. In 1989 through 2002, the recovery efficiency of dozens of sluicing systems was determined by mixing radioactive gold particles (tracers) into the feed streams of dozens of placer mines in the Yukon Territory, British Columbia, Alaska and Guyana. Four distinct sizes of nuclear tracers were used and their recovery was related to the design and operational characteristics of the individual sluiceboxes and their pay gravels. At clean up, scintillometers were used to detect the very low level X-ray and gamma ray radiation emitted by these tracers and locate them in the sluice runs. The effectiveness of any given section of riffles was easily diagnosed by the presence or absence of tracers. At every mine the gravel feed rates, water flows, equipment dimensions and riffle performance were measured. After the gold tracers were removed from the fi nal concentrate and counted, the concentrate was sieved and weighed. These gold recovery, weight and sieve data were used to calculate the quantities and size distributions of the gold particles in the original pay gravels and those lost in the tailings. The expired tracers were stored in a lead lined container until their radioactivity was near background levels (about two months). The standard errors from these radiotracer tests were estimated from binomial probability theory with the equation: SE = {(n + p + q) ^ 0.5}/n. Where n was the total number of radiotracers added, p is the proportion recovered and q was the proportion lost. Each overall recovery estimate would be within one standard error of the true recovery value (14 times out of 20) and almost always within two standard errors of the true recovery (19 times out of 20). The maximum standard error with 100 tracers was five per cent and occurred when the recovery approached 50 per cent. With higher recoveries, standard errors usually ranged from one to two per cent.

Aug 1, 2010

By Paulo José Costa Couceiro Junior, Manuel Lopez Cano

The biggest Port of Latin America - the Santos Port in São Paulo, Brazil - has been drilled and blasted by controlled underwater techniques in order to remove around 40,000 m3 (52,318 cubic yard) of rock divided in two outcrop rocks: Teffé and Itapema. Underwater pumped explosive, in combination with small cartridges areas, was successfully used in order to reach a target depth of -15m (-49 ft) and a width of 220m (722 ft) in the navigation channel. It was the first time that a pumped explosive was used in underwater blasting in Brazil and it represents a historic benchmark for projects of this kind in this country. The main challenges faced in this project include the control of the ground vibration, due to the necessity to carry out detonations 40m (131 ft) away from the quay wall - where the passenger terminal and the 80 year-old warehouse were located – and the rush schedule available, in order to finish the underwater drilling and blasting phase before the coming cruise season. Therefore, the perfect combination of an ideal pumped product with an effective pumping system has permitted to carry out the project in a record of less time than 3 months (against to the original expected time of 18 months), with all vibration events under control as result of the special ground vibration program carried out.

Jan 1, 2016

The principal dirnensions of the chimney were fixed as follows: Height from formation to coping, 328 ft. 8 in.; inside diameter concrete shell, 13 ft. Gin.; inside diameter of the 4~-in. brick lining. 11 ft. (j in. ; shell thickness above flue inlet at a point 39 ft. above formation, 1 ft. 8in.; shell thickness at coping, 6 in. That is, the inside of chimney is cylindrical, wldst the outside is gradually stepped inwards with of 1 in. and less until the shell is 6 in. thick only at the top. With these dimensions in mind, it will be seen that some close thought was necessary to ensure a satisfactory of fonn which could be kept rigid and plumb to a height and at the same time provide safe working conditions for the labourers employed.FOUNDATIONSThe spread base of the chimney is 45 ft. in diameter, and foundations were carried down to a depth of 8 ft. 6 in. below natural surface into good hard clay which was known to be the best foundation obtainable in the vicinity being capable of withstanding, when dry, a load of 3 tons to 4 tons per square foot, whereas dead load is 1A tons per square foot and the maximum load expeeted under the most severe wind condition is 2 tons per square foot to ensure the foundation being kept dry and unaffected by ground water, the site was surrounded by a ring drain at a distance of six feet from edge of concrete foundation and at a minimum depth of one foot below bottom of concrete. Open-jointed pipes were laid in the bottom ofthe drain and graded to a pipe drain with outfall clear of the site.

Jan 1, 1924

By T. Holmes, J. Middlemiss

"Agnico-Eagle (AE) has been operating their Kittila Mine in Northern Finland since 2008. The mine has experienced considerable ore flow problems with ratholing, bridging and freezing in their mill feed bin since start up. In the first winter of operation, the entire central portion of the contents of the cylindrical flat-bottomed 2000 tonne mill feed bin froze. Flow was erratic and could only be achieved through small diameter ratholes. To maintain a reasonable, albeit limited, feed to the mill, the bin had to be kept less than ½ full and a portable steam generator was brought in to melt the frozen agglomerates that frequently blocked the outlets. The combination of limited surge capacity and frequent outages required the crushing plant to operate 24/7 and resulted in inconsistent production levels and high operating costs.AE had planned to expand the processing plant to increase throughput by about 30% when they transitioned from open pit to underground ore. These plans presented an opportunity to improve the material handling.To avoid the problems experienced with the original mill feed bin, AE enlisted Jenike & Johanson Ltd. (J&J) to test samples of the ore, and based on the measured flow properties to provide design recommendations to ensure that the new mill feed bin would operate reliably. The new 2000 tonne expanded flow mill feed bin and apron feeder were installed in 2014 and are now supplying almost 93% of the total mill feed with the remaining coming from the original bin.IntroductionIn early 2009, AE engaged J&J to visit their then recently opened Kittila mine and mill in Northern Finland (Figure 1). Over the first half-year of operation, production had been restricted in the ore handling and storage system by flow problems such as ratholing, bridging and freezing including blockages of chutes and hoppers as a result of frozen fines buildup and large frozen agglomerates. AE wanted to increase production in the existing open pit mine and mill feed operation and also wanted to avoid similar ore handling problems when they commissioned the new underground mining system under development at that time."

Jan 1, 2017

By W. J. Spat

Political risk is an integral part of the mining business in northern Andean countries. Peru, Ecuador, Colombia and Venezuela all have a higher than average political risk compared with other South American countries. Successful operations require good political-risk information, a thorough political-risk-management plan and a strategy to deal with political-risk perception on the part of the investing public. Colombia is perceived as about the riskiest place in the world to do business. A selection of recent headlines reads: “Colombia on the brink” (Economist, 1998), “Colombia’s ship of state is sinking” (Insight on the News, 1998), or simply “Bad news” (US Catholic, 1998). The World’s Most Dangerous Places rates Colombia as “currently the most dangerous place in the Western Hemisphere, and perhaps the world” (Aral and Pelton,1998). And many prospective investors and analysts say to Greystar Resources: “Yes, we love your results, but Colombia?”

Jan 1, 2000

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

Typically, large volumes of data are collected during geotechnical investigations for mining projects but rarely is this done in a comprehensive manner that enables all aspects of the geotechnical environment to be evaluated. A geotechnical core logging process has been developed to record mechanical and structural properties of the rock mass. The method enables data for a wide range of rock properties and geotechnically significant major structures to be collected including rock strength, joint surface condition, fracture frequency and fracture orientation. The logging method is unique in that sufficient data is collected to enable the independent determination of all the major rock mass classification systems including rock mass rating (RMR), (Bieniawski 1976, 1989; Laubscher, 1990) Norwegian Geotechnical Institute (NGI) tunnelling quality index (Q) (Barton, Lien and Lunde, 1974) and geological strength index (GSI) (Hoek, Kaiser and Bawden, 1995). The logging system has been specifically developed to allow better and more precise appreciation of rock mass and structural conditions across the project area thereby optimising the use and application of the available geotechnical data and improving confidence in the outcomes of geotechnical investigations. This paper describes the core logging process with case examples showing how the logged data can be used for underground and open pit mine design.

Nov 25, 2010

By F. H. Buchella, J. F. Buchanan

The San Manuel copper deposit is located about 45 miles northeast of Tucson. The concentrator, smelter, administration building, and other plant facilities are located about seven miles southeast of the ,nine area at the new town of Sari Manuel as shown on Figure 1 (Sketch).

Jan 1, 1961

By D. Settles, R. Rose, P. L. Dunn

"A new mineral sands operation is being developed in Georgia by Southern Ionics, Inc. (SII). Prevailing mineralogy and certain design constraints required detailed testing and circuit analysis to create a robust separation processes. The floating wet concentrator plant (WCP) and mineral separation plant (MSP) flow sheets were designed based on historical testing information and recent SII test campaigns on various composite feed samples. The flow sheets were finalized through rigorous process and orebody sequence modeling.The process uses traditional physical separation equipment; however a new MT spiral, the MG12, was selected for use on board the WCP for roughing duty. The MG12 spiral is a two-stage, twelve-turn spiral that has been proven to achieve very high recoveries of heavy minerals. The floating plant includes feed desliming operations, a central MT surge bin for optimum spiral circuit feed control and ancillary operations for concentrate and tailings handling. Scrubbed heavy mineral concentrate (HMC) is then transported to the MSP for concentration of the titanium and zirconium bearing mineral fractions.The testing, flowsheet development, and plant design will be described and explained, and a brief summary of the current project status will be given.IntroductionSouthern Ionics Inc. (SII) is a privately held chemical manufacturing company, founded in 1980 by Milton Sundbeck. SII focuses primarily on the sale of specialty and intermediate inorganic chemicals. Core markets include cement and refinery catalysts, molecular sieves, zeolites, pulp and paper, pharmaceuticals, TiO2 and water treatment. SII is built on the four cornerstones of service, quality, technology and delivery with all SII facilities ISO certified and key products used in potable water treatment certified to NSF standards. SII owns and operates its own transportation fleet and is focused on being a low cost producer, committed to safety and the environment."

Jan 1, 2015

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

Jan 1, 2001

By Corale L. Brierley

Beneficiation of phosphate in the southeastern United States generates a slurry of finely divided clay. These clay-wastes are impounded to allow the particulates to settle. The aggregation of phosphatic clay-slime wastes and slimes produced from potash beneficiation by microbial processes was studied using several bacterial species known to produce polymeric substances. Experiments included flocculation capacity of clay-slimes by whole cells, the determination of respiratory activity of whole culls in the presence of phosphatic clays, observation of clay flocculation rates by polymers derived from these organisms, and clarity of polymer-flocculated clay suspensions. The polymer-producing organisms exhibited little capacity for flocculating phosphate and potash clay-slimes. Fungal spores of Cladosporium cladosporioides (isolated from a phosphate clay-waste impoundment), when agitated with clay-slime for several days, caused the clay to form pellets. Separation of the clay/fungal pellets (density 1.1 g ml-1) from the process water might he possible using a screening technique. Studies with C. cladosporioides included the determination of suitable energy substrates and supplements for growth, absorption studies of a pigment produced by the organism, determination of the time required for bioflocculant production by the organism, and an elucidation of the conditions required for the pelletization of clay-slimes by the fungus.

Jan 1, 1982

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983