Search Documents

By Vance G. Leak

Leaching of manganese from low-grade Minnesota ores was studied over the temperature range 25° to 225° C at atmospheric and elevated pressures to demonstrate that good recoveries of manganese could be achieved from unroasted ores using reagents available nearby. Various combinations of ore, pyrite, lignite derivatives, and sulfuric acid were tested on a small scale. Pyrite alone required the highest temperature to effect a good extraction, but the combination of pyrite, lignite char, and sulfuric acid solubilized 99 percent of the manganese after 30 minutes of reaction at 75° C.

Jan 1, 1971

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

By Michael D. Justason

...a global perspective... In March of 2000, the Japanese Geotechnical Society added "Rapid Load Testing" to their national standard for pile testing. In the year 2000. it is estimated that there will be more than 500 "Rapid Load Tests" on foundations around the world. ...so what is a "Rapid Load Test", and why is it gaining acceptance and popularity?

Jan 1, 2001

By Robert A. Bradburn

The Bureau of Mines has developed a miniature, portable two-level oxygen-deficiency alarm and produced three prototype models. Each operates from a 4.2-v dc power source, and the highest current drain of any model is 80 ma. An electrochemical cell, which produces an electrical output in proportion to the partial pressure of oxygen to which it is exposed, is used as an oxygen detector. The output of the cell is applied to an electronic circuit that detects two different levels of oxygen percentage below that of normal air, and produces distinct audible signals at these levels. The hazard alarm mode is activated when the oxygen percentage first drops below normal and produces a 500-cps "beep" tone with an intermittency of 1 cps. The danger mode produces a continuous 500-cps audible signal when the oxygen percentage drops still lower.

Jan 1, 1968

By L. M. Irwin

This Bureau of Mines investigation relates the physical properties of copper reverberatory furnace slags to changes in composition, The smelting of upper Michigan copper ore presents some problems that probably differ from those of other copper smelting areas. The study of these problems has, however, provided important data regarding slags in general and therefore will be of value to other operations as well. Conclusions reached from this study were: (1) Slag fluidity and refractive indices varied directly with the iron content and inversely with silica, lime, and alumina, and (2) there was no apparent correlation between slag fluidity and its copper content.

Jan 1, 1962

By James C. Barker

A uniquely mineralized area extends from northwestern Canada through Alaska into eastern Siberia. Some of the metals found there are relatively rare in the conterminous United Stales. Among these are cobalt, the platinum-group metals, and chromite. Geologic evidence suggests that cobalt and the platinum-group metals may be present in deposits that could constitute nationally important reserves. Chromite in potentially minable deposits is known, but it may be relatively less abundant. Limited reserves of these metals have been delineated, but most of the favorable terranes and reported occurrences throughout the vast expanse of Alaska remain unexplored. As part of the mineral studies mandated under the Alaska National Interest Lands Conservation Act, the Bureau of Mines&apos; Alaska Field Operations Center and the Bureau&apos;s research centers at Albany, Oreg., and Reno, Nev., are cooperating in a long- range program to investigate occurrences and delineate reserves of cobalt, the platinum-group metals, and chromite in Alaska. Studies of other critical and strategic minerals will be phased in during succeeding years, as ongoing projects are completed. This first in a series of annual reports summarizes available information about deposits and past production of cobalt, the platinum-group metals, and chromite, and describes current and planned Bureau investigations of these minerals.

Jan 1, 1981

By Andrew K. C. Wong

Hydraulic transport has been considered as one of the most economical methods in transferring granular materials over relatively long distances. In the natural world, it is used to transport basic material required for the support of life; in industry, it is a method widely adopted for handling materials. But the phenomena of hydraulic transport has not yet been thoroughly understood. As most of them are conditioned by a number of hydraulic and mechanical parameters, of which the basic relationships are not fully known, the traditional approach in relating these parameters to the energy requirement is purely empirical in nature. Empirical formulas, such as that proposed by Durand, (1) only give satisfactory results over a selected range of (particle size)/(pipe diameter) ratios and slurry concentration. When the case is more complicated or when new situations arise, the empirical formulas fail to give good predictory results. In fact, most of these formulas are based upon dimensional analysis, where the underlying physical interaction is not explicitly considered. Apart from the loosely related, non-dimensional groups incorporated in the formulas, there is practically no analytical means for modifying the formula so as to enable it to cope with more complex real physical situations. Although it seems quite remote that a complete rigorous solution to this highly complex problem could be generated in the near future, it is generally recognized (2, 3) that research in this area should be directed to more comprehensive studies of the obscure phenomena. In fact, there are a good number of very basic problems such as the effects of gradation and concentration of particles upon

Jan 1, 1972

Electrical trailing cables are frequently damaged in usage, especially on continuous minors, and because of their weight and damaged condition present a safety hazard to personnel required to handle them. The U.S. Bureau of Mines and FMC Corporation signed Contract No. HO 122011 in August 1971. One of the contract tasks was to study the feasibility of techniques to improve trailing cable support and handling of power cables on underground coal mine machinery and to design a cable-handling device for a continuous mining machine. This report presents the results of the feasibility study, describes the design for a proposed cable handling device and concludes with a recommendation for future action to construct a test rig to evaluate the cable reel system.

Jan 1, 1972

By James W. Hendrix

A survey of endomycorrhizal fungi occurring on orphan coalmine lands in Western and Eastern Kentucky revealed a great diversity of species present. Thus a large number of fungi are available for isolation and evalution for enhancing revegetation of mined land. Endomycorrhizal fungi isolated from orphan mines stimulated growth of sweetgum seedlings on mine soil at low fertilisation but inhibited growth at high fertilization; this growth inhibition at high fertilization did not occur with plants growing on peat-perlite. Banding of endomycorrbizal inoculum was not advantageous, compared with incorporation of inoculum throughout the growth medium, for production of mycorrhizal sweetgum seedlings. Newly reclaimed mine spoils were nearly nonmycorrhizal, compared with land reclaimed four or eight years earlier. A procedure for isolation of single-spore cultures of endomycorrhizal fungi was developed; this procedure is necessary for studies of ecotypic variability. A practical procedure using container-grown Pisolithus tinctorius-infected shortleaf pine seedlings for production of large numbers of bareroot pine seedlings infected with P. tinctorius for mined land reclamation was demonstrated.

Jan 1, 1982

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By E. F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged mechanical dust collectors (scrubbers) with high dust collection efficiency and low energy comsumption for controlling dust in coal mining operations. All of the scrubbers described are similar in configuration and are powered by 6-hp, 2,000-ft3/min vane axial fans. Air pressure differential is less than 6 inches water column. Height of the scrubbers? including fan is less than 14 inches, width is less than 16 inches, and length is less than 45 inches. The flooded fibrous-bed scrubber achieved respirable (less than approximatey 7 µm) dust collection efficiencies of 95 percent. The small-diameter-cyclone scrubbers showed about 92 percent efficiency and can be best where excess water is a problem. The wetted brush scrubber showed 88 percent efficiency at low cost, and the wetted fan scrubber showed a slightly lower efficiency (87 percent) but offered the smallest size and cost. A suitable water droplet eliminator is described.

Jan 1, 1978

By C. E. Brechtel

A testing program was conducted to design a cemented backfill fur hydraulic placement in underhand cut and fill mining of a steeply dipping coal seam. The testing evaluated the use of three different backfill aggregates, locally available at the coal mine, with Portland cement and five different pozzolans, including a Class F fly ash, a Class C fly ash, a cement kiln dust and ground smelter slag. Both viscosity and uniaxial compressive strength of backfill mixtures with different pozzolan and Portland cement contents were used to evaluate their suitability. Based upon the results of preliminary testing, an optimum mixture of alluvial sand with six percent Portland cement and ten percent Class F pozzolan was chosen for further compression testing.

Jan 1, 1985

[ ]

Jan 1, 1979

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection Paid operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection and operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939

By Robert L. de Beauchamp

The Bureau of Mines designed a chlorination apparatus to prepare CrCl2 free of CrCl3 by the direct reaction of chlorine and chromium. Equipment and procedures were developed for routine preparation of 25-pound batch quantities of anhydrous CrCl2. Calcium, iron, nickel, and silicon impurities were in the 0.01 to 0.05 percent range, and all other impurities were below 0.01 percent.

Jan 1, 1968

By Joseph Grumer

Theory pertaining to the exchangeability of fuel gases on appliances has been extended to exchanges of propane or butane with mixtures of these. In particular, new considerations were developed bearing on the hazard of an occasional emission of carbon monoxide and flashback and blowoff possibilities. The new considerations involve using current requirements for approval of liquefied petroleum gas appliances. These requirements were used to predict allowable tolerances in chemical composition of liquefied petroleum gases for existing appliances. In addition, changes in gasline pressure were computed which may be substituted in place of fuel exchanges during testing of appliances,

Jan 1, 1962

By G. J. Hasenfus

This paper presents the results of an extensive hydrological and geomechanical monitoring program which Gas conducted at a longwall coal mine in W. Va. The field program included monitoring of groundwater levels. overburden hydraulic conductivity, overburden movement, and surface subsidence relative to the passage of the longwall. Overburden geology and rock strength characteristics were evaluated prior to mining. A postmining corehole was drilled to evaluate main roof fracturing. An overburden response model is proposed based on the correlations between hydrological and geomechanical data.

Jan 1, 1988

By L Baumgardner, A. V. Castelli

Barite In 1987, United States mine production of barite increased 15.870, consumption (sold or used by grinding plants) increased by 6.97, and imports are estimated to have fallen by 19.57. World mine production decreased by 137, according to the US Bureau of Mines. The value of US produced barite, fob mine, decreased 1.4%, according to the Bureau. The declared value for cif US port of all imported unground barite during the first 10 months of 1987 decreased from $39.02/t ($35.40 per st) to $37.16/t ($33.71 per st), the Bureau stated. Nevada continued to be the leading US producer of&apos; barite with 637r of the total. It is followed by Georgia, Missouri, California, Tennessee, and Montana. The Bureau of Mines estimates 657 of the US mine production was used as a weighting agent in drilling fluids. The remaining 35°/r was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the non-oilfield sector. This sector continued to increase. Of the total consumption (used by grinding plants and chemical manufacturers), it is estimated that 8070 was used in drilling fluids and 2017( in the non-oilfield sector - barium chemicals and fillers in paper, plastics, and glass. The tonnage consumed in the drilling fluids market increased slightly. But the average number of rotary rigs operating decreased from 964 in 1986 to 936 in 1987. This is the lowest number of operating rigs reported since 1949. The increase in consumption in this sector is due to an increase of rigs operating in the US Gulf and other higher consumption areas over 1986. Crude barite imports were estimated to be down by 19.5% in 1987. Still, they accounted for 637 of the barite consumed in the US. During the first 10 months, China continued to be the leading exporter to the US with 86.970, followed by Mexico with 10.997, and Morocco 2.107(. About 5Y of the imported ore was used in the nonoilfield sector. Ground barite imports dropped from 19.8 kt to 8.8 kt (21,800 st to 9800 st) in 1987. Of this amount, 1.4 kt (1598 st) was used in drilling muds and the remainder of the non-oilfield use. During 1987, a few more grinding plants that supplied the drilling fluid market were closed. Along the US Gulf Coast, there are 13 operating plants versus a high of 31 in 1981. Cameron Offshore reopened its grinding plant at Cameron, LA. New Riverside Ochre Co. of Cartersville, GA, purchased a jigging-washing plant in Missouri and plans to place it in operation this year on a new deposit near Cartersville, GA. Milpark purchased Hughes Drilling Fluid in 1987 and operates under Milpark. US mine production will probably stay about the same as 1987. Price increases in the 10 % range for imported ore are expected due to water freight and the weak dollar. Baker Hughes estimates the average number of operating rotary rigs at 1070. A slight increase is expected in the non-drilling fluid market (chemicals, glass, and filler). Bauxite and alumina L. Baumgardner, US Bureau of Mines Domestic bauxite production in 1987, expressed as dried equivalent, was 581 kt (640,400 st), a 14% increase over 1986. US mine production amounted to less than 170 of total world production. Virtually none of the domestic bauxite was consumed in the production of primary alumina metal. About 30% of the bauxite produced by US mines was calcined to produce 117 kt (128,970 st) for use in abrasives, catalysts, chemicals, proppants, and refractories. Most of the uncalcined bauxite was refined to specialty aluminum oxide (alumina) forms. Metallurgical grade bauxite was imported from 10 countries in 1987. Principal suppliers of the 9.8 Mt (10.8 million st) were Guinea (4270), Jamaica (3501,), Australia (127), and Brazil (57). The average value, delivered U.S. ports, cif, as reported to US Customs Service, was $29.50/t ($26.76 per st). Calcined refractory grade baux-

Jan 6, 1988