Search Documents

By Jiwen Zhang

Due to the blocking nature at the crusher station, straightforward application of queuing theory cannot give realistic results on the performance of a shovel-truck-crusher system. A new queuing network-based model has been developed in which, the crusher station is formulated into an open queuing network and the whole shovel-truck-crusher system into a closed queuing network with the crusher station as a special server. To fully account for the influence of blocking, Monte Carlo simulation is first used to obtain the performance parameters of the open queuing network for the crusher station. The closed queuing network for the entire system is solved by applying the Extended Summation Method (ESUM), in which the crusher server is described by the simulation results. The model has been applied to the Yuanbaoshan open-pit coal mine to analyze its shovel-truck-crusher system and to improve its efficiency. Results indicate that the blocking at the crusher is an important factor affecting the crusher output and in turn the efficiency of the whole system, and prove that the model can realistically describe the behavior of such systems.

Oct 1, 2009

By C. A. Hesse

The Quartz Hill Molybdenum Project, In Southeast Alaska, was the first mining project to attempt the permitting of a submarine tailings disposal system in the United States, since the passage of the National Environmental Policy Act of 1969 and the Clean Water Act of 1977. Over $20 million was spent by the project developer in baseline data gathering and In funding the preparation of the four Environmental Impact Statements and other environmental documents required at various stages of the project between 1977 and 1988. Because of the timing and a unique set of environmental, legal and regulatory requirements which applied to this project, innovative approaches were developed. This report describes those requirements and the developments, and gives a full historical account of the campaign for permitting submarine tailings disposal at Quartz Hill, until denial of the NPDES permit application by EPA in September 1 990. The extensive studies done for Quartz Hill suggested that under certain conditions the selection of submarine tailings disposal can be the overall environmentally preferred alternative for a mining project. The Quartz Hill story illustrates the complexity of the existing permitting structure and paints out the desirability of rationalization to achieve a more effective system.

Jan 1, 1993

By W. F. Faragher

The principal equipment in the catalyst plants at Ludwigshafen-Oppau was inspected and is presented in the form of flow sheets for the manufacture of four of the principal catalysts. The equipment is in many cases of special design rather than stock items that was built by the company and modified in the coarse of the growth of the high-pressure synthesis of hydrocarbons in Germany. It is believed that if the manufacture of catalysts were to be undertaken elsewhere, the selection of equipment for the operations involved could be made successfully from the guidance furnished by this rather general report. Five additional catalysts are described, also. II. CATALYST 5058 FROM FRESH TUNGSTIC ACID In a supply tank of about 2,000 liters capacity, 500 kg. of tungstic acid (W03.H2O) that contains about 92-93 percent of W03 is dissolved at 60-70° C. in 1,500 liters of mother liquor. The solution is-effected by stirring for about 1-1/2 hours. The mother liquor is obtained from a previous, lot of catalyst and is first adjusted to a concentration of 13 percent 1H3 by passing in gaseous ammonia. The solution is allowed to stand without stirring for 1 hour, then is pumped into the saturating vessel through a cloth filter (three-quarters hr. to one hr.). The saturator is purged with H2S and thereafter the solution, which has been cooled to about 75° C., is heated in an atmosphere of hydrogen sulfide with stirring to about 70° C. This charge is slowly cooled to 50°, and then more rapidly to about 20° C. (time of cooling 6-7 hours).

Jan 1, 1946

"INTRODUCTION Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States, Accordingly, the 74th Congress appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions and hearing 2/ relative to the need for the survey, the opinion was expressed that crude oil held in storage for long periods had lost so much of its gasoline content that the economic significance of total stocks should be discounted materially. Therefore, a primary objective of the survey was to make a physical inventory of the crude oil held in storage above ground and to determine the quantities and characteristics of the light fractions contained in the various stocks."

Sep 1, 1938

By John C. Machisak

Employment and related injury experience of the coking industry in the United States for 1957 contained in this publication is summarized under three general sections: (A) General injury experience: Tables 1 to 9: Current and comparable statistics on operating data, number, frequency, and degree of severity of injuries and major accident agencies involved in the cause of Injuries. Data are presented for the industry as a whole, for each type of oven, and for the States in which coke was produced.

Jan 1, 1959

By Donald Whittaker

Severe climatic conditions in mines are normally associated with working at depth. More precisely, it is a matter of working in regions of high strata temperature, since, for example, some coal mines in the Ruhr have strata temperatures at 1000 m which are matched only at 3 times that depth in the South African gold mines. In Britain we are perhaps fortunate in encountering strata temperatures in our deeper coal mines some 10-15 K lower than at the same depth in the hot mines of the Ruhr. Nevertheless the problems of high temperatures and humidities in UK mining operations, which in the past have been confined to a few specific sites, have in recent years become more widespread, and there is every reason to suppose that the trend will continue. Clearly strata temperature is not the only .causative factor. Long ventilation circuits serving districts remote from the shaft must also play a part, while the heavy use of machinery and the rapid, rates of excavation of modern mining methods are obviously important. It is necessary to understand the mechanisms of all such factors, and to measure their magnitudes and fluctuations, if remedial measures are to be properly designed or predictions made which are accurate enough to be of use in ventilation planning. This paper presents the results of a long-term (and continuing) investigation carried out in several mines to measure the major sources of heat and moisture on longwall districts and trunk conveyor roadways. The variation with time of these sources is reported, and the resultant effect on the climate is considered. In their investigations of the heat exchanges occurring in a whole mine Oakes and Hinsley (1955-56)1 listed and estimated the magnitudes of a large number of heat sources. Some of these, namely autocompression of the air in the shaft, diesel engines and compressed air mains, do not apply to the present investigations, which refer to longwall districts with conveyor transport and no compressed air supply. Others, such as oxidation of coal and, desorption of methane, have not been taken into account in the measurements, but are discussed later. One other source, the importance of which was pointed out by Gracie and Matthews (1975)2, is the coal on the conveyor, a form of strata heat emission, but one which is strongly dependent on the rate of coal production. The heat emissions measured in the present investigations were the energy consumed by electrical machinery, the heat conducted from the strata and the heat lost by the conveyed coal. Most of the emitted heat was removed from the district by the ventilation air, and was measured by continuously recording the enthalpy of the air at fixed stations. The heat removed by service water, supplied for machine cooling and dust suppression, was also measured. Account was of course taken of the relatively minor changes in level around the districts, in terms of the potential energy gained or lost by the coal and by the ventilation air (autocompression).

Jan 1, 1980

By S. Usui, I. Iwasaki

The adsorption mechanism of dodecylammonium acetate (DAA) on mercury in potassium fluoride solutions at natural, near neutral pH was investigated. Difler-ential capacity combined with electrocapillary measurements on a dropping mercury electrode were found to provide a sensitive and reliable approach. A shift in the electro capillary maximum (or the point-of-zero-charge) towards positive polarization of the surface due to the adsorption of amine indicated a specific affinity of dodecylammonium ion for mercury surfaces. The amine was shown to adsorb competitively with potassium ion on mercury. Through correlation of the adsorption density of the amine, calculated from the thermodynamic analyses of the electrocapillary curves, and of the diflerential capacity curves, the adsorbed state and the orientation of the amine at the interface were considered. The similarities and the differences in the adsorption behavior of the amine on mercury and on such ionic solids as quartz, silver sulfide, and silver iodide were evaluated. With the promise of flotation providing a cheap and large-scale process for the upgrading of low-grade ores and magnetic concentrates, the iron ore industry has made a sustained search over the years for a flotation reagent of general applicability and high selectivity. Having shelves full of commercial reagents already on hand and anticipating more, both the users and the suppliers are in need of an experimental approach sensitive enough to differentiate the individual characteristics in each group of reagents. Therefore, the adsorption behavior of various flotation reagents on mineral surfaces from aqueous solutions has been a subject of much investigation. The current view of adsorption based on the electrical double-layer theory is formulated on the assumption that certain ions in solution act as potential-determining ions. Their concentrations fix the potential drop across the double layer and their adsorptions govern the surface charge.' Two methods used to study the adsorption

Jan 1, 1971

By Yuanming Pan, Brett Rogers, Baoquan Hu, Gary Yeo, Christine Austman

The nature and distribution of radiation-induced defects (RIDs) in quartz from the Maw Zone, a yttrium- and rare-earth-element-enriched sandstone breccia complex exhibiting intense hydrothermal alteration, have been investigated by electron paramagnetic resonance (EPR) spectroscopy. EPR spectra show that detrital quartz in sandstone, from five diamond drill holes intersecting the Maw Zone and one above the crest of the so-called Quartzite Ridge, contain only background-level RIDs, indicating that Ubearing fluids were absent in this area. However, close to the sandstone-basement unconformity, in hole WR-194 immediately west of the Quartzite Ridge, the concentration of RIDs in detrital quartz is significantly above background but at least an order of magnitude lower than those at the Key Lake and McArthur River deposits. Widespread drusy quartz at the Maw Zone, which signifies intense hydrothermal alteration, is associated with hematite-, sulfide- and carbonate-bearing mineral assemblages, which exhibit complex crosscutting relationships. EPR spectra of drusy quartz in all three types of mineral assemblages are low in RIDs as well, supporting the EPR evidence that fluids at the Maw Zone did not carry significant U. These EPR results suggest that, in spite of intense hydrothermal alteration and favorable structural geology, the Maw Zone is unlikely to host any significant U mineralization. Moreover, this study shows that the EPR technique is potentially a useful exploration tool, capable of determining whether individual alteration zones in the Athabasca Basin were associated with U-bearing fluids or not.

Jan 1, 2013

By Slobodan B. Vujic

"Some twenty years ago, during construction of flotation in the “Veliki Krivelj” copper and non-metallic mine Bor, a computer supported system for remote controle of technological process was installed. Nowadays, the major part of equipment of this system is worn-out and technically old-fashioned. Having this in mind a decision was made to design a new computer supported information-management system for Flotation. The paper presents a concept and features of project solutions.For the requirements of remote monitoring and management of technological process in Flotation of “Veliki Krivelj”, Copper and non-metallic minerals mine in Bor, Yugoslavia (hereinafter: CNM Bor), a measuring-regulation equipment was implemented and a computer control system, adjusted for that time, built some twenty years ago. The major part of this equipment is today worn out and technically out of date.Having estimated that production and business activities could hardly be more efficient, operative and successful on one hand, and available mineral and other resources rationally exploited, the CNM Bor made a decision in 1999 to improve information-management function of Flotation. The idea was that the set task be realized through development and introduction into practice up-to-date integrated and computer-supported production-business information-management system. The first logic step in completion of this task refers to engineering-creative determination of information management system (hereinafter: IMS), namely to project elaboration.When considering the real system from technical, technological, organization, monitoring-management, logistic and business aspects, the Project on IMS of Flotation, should provide a rational, modern and, for the real system conditions, complete solution. The Project solutions should be based on the most recent knowledge from computer and measuring-regulation technics as well as from CIM concept (Computer Integrated Manufacturing)."

Jan 1, 2003

By Carlos Rebolledo, Nelson Parra

Arsenic is an unresolved problem in the mining industry considering the fact that most of the new copper deposits have high arsenic contents; stricter environmental restrictions for handling, transporting and processing complex materials are expected and stable abatement of arsenic is not extensively applied. In 2018 Chile produced 24.5% of the total copper from concentrates and in the future copper production in Chile is expected to increase, mainly associated with production of concentrates that will also contain more arsenic. China has set an import benchmark of maximum 0.5% for arsenic content in copper concentrates and this value is expected to be more restrictive in the future. On the first day of 2018 China banned the importation of scrap. Blending practice has been a business option, but it is not sustainable in the future, as “normal” copper concentrates become less and less clean. By the end of 2018, Chile formulated new regulations, increasing the capture of SO2 and arsenic to 95%. In order to comply with these regulations Chilean smelters had to make large invest large amounts of money. Disposing of arsenic as a stable residue is a pending issue. EcoMetales is a 100% subsidiary of Codelco and provides the mining industry with environmental solutions. It has a plant near Calama in Chile that treats flue dust from smelters, refinery effluents and acid solutions from acid plants. EcoMetales is fully committed to contributing to the solution to the arsenic problem. Currently we are developing four main projects: 1) Concentrates treatment. A PLCC project considering the treatment of 200 ktpy of copper concentrates with arsenic from the northern district of Codelco; 2) EPAS DET project considering the treatment of 700 m3/d of weak acid solution with arsenic from the of El Teniente devision of the Codelco acid plant; 3) Borras project, considering the recovery of valuable metals (Cu, Ag, Ge, Pb) from the flue dust leaching plant; 4) Tailings project, considering the recovery of metal values from tailings. The purpose of this work is to present the trends and treatment processes for arsenic handling in the copper mining industry with a focus on the scorodite process. INTRODUCTION Between 2000 and 2015 the global copper concentrates production has grown from approximately eleven to fifteen million metric tons per year. Chile produced 26.5% of the total copper from concentrates and in the future copper production in Chile is expected to increase, mainly as a result of the production of concentrates (Figure 1)

Jan 1, 2019

By Mark J. Klein, Robert A. Haggins

The pesence of a small amount of oxygen was found to cause significant grain growth restraint in 99.99 pct Ag. This behavior does not seem to be due to the presence of an oxide dispersion, but instead, to be related to the existence of minute amounts of oxygen m solid solution. In the amounts necessary to cause the observed effects it was found that oxygen migrates with extreme rapidity, probably along extended structural imperfections, such as dislocations and grain boundaries. A number of years ago, hastton' observed that the presence of small amounts of oxygen caused a retardation of grain growth in silver. He attributed this behavior to the formation of a fine dispersion of oxide particles by the internal oxidation of trace impurities. More recently, wood2 also found that oxygen caused grain growth restraint in copper. Experiments using both copper and a dilute solution of aluminum in copper led to the conclusion that the effects observed in copper were due to oxygen in solid solution, rather than an oxide dispersion. During the course of a study of the influence of several solutes on the recrystallization of Silver, the presence of minute amounts of oxygen was found to exert a very significant influence on grain growth. The experiments reported here were undertaken to determine whether the grain growth restraint observed in silver due to the presence of oxygen is related to oxygen in solution or to an oxide dispersion. Because of the difficulty in measurement and control of the very small oxygen concentrations causing the observed effects no attempt was made to treat the data in a quantitative manner. EXPERIMENTAL PROCEDURE AND RESULTS Silver of 99.99 pct purity was melted and cast into slabs in a vacuum of better than 0.1 p. These slabs were reduced 50 pct by cold rolling to a thickness of approximately 2.5 mm. Samples cut from this material were annealed in vacuum for a series of different times at 803°C. Another group of samples was similarly annealed in air. This temperature is well above the recrystallization range for silver of this purity (150" to 200°C). The mean grain diameter of these samples was measured, both in the center and near the edge, using the line-intel-cept method, and is shown as a function of annealing time in Fig. 1. The grain size in the centers of the samples annealed in air was found to be larger than that of the surface regions, while the grain growth behavior of the edge and center regions annealed in a vacuum was approximately the same. he edge measurements were taken at a distance of 0.2 mm from the surface.) A few samples were annealed in nitrogen. Their behavior was identical to that of the vacuum-annealed samples. Samples annealed in oxygen had approximately the same grain growth behavior as those annealed in air, leading to the conclusion that this behaviouer is due to oxygen. The microstructure of a sample annealed in air at 803" for. 30 minutes is shown in Fig. 2. The smaller grain size near the surface is characteristic of the iir-annealed specimens. Possible causes of this grain growth restraint in the air-annealed specimen are the formation of an im-

Jan 1, 1962

By K. A. Jackson

An analysis of the conditiom fm the dendrite-eutec-tic transition is presented which takes into account a temperature gradient. The composition and temperature in the liquid ahead of a eutectic interface growing at a particular velocity are used to determine whether dendrites can grow faster than the eutectic interface in the liquid which exists ahead of it. If the dendrites grow faster, then a mixed structure with dendrites growing ahead of the eutectic interface is expected. If the dendrites do not grow faster, then only eutectic will be present. The analysis is presented for Sn-Pb system, for which sufficient experimental data to make the analysis are available. The transition from eutectic to dendrites-plus-eutectic derived by this analysis is in good agreement with the recent experimental observations of Mollard and Flemings on Sn-Pb alloys. In alloys which grow with a lamellar eutectic structure, the lamellar structure can be grown over some range of compositions close to the eutectic composition. When the composition is too far from the eutectic composition, dendrites of one or another of the primary phases grow ahead of the eutectic interface, producing a microstructure consisting of "primary phase" interspersed with a lamellar eutectic. Hunt and Jackson' have recently predicted the range of compositions over which the eutectic phase should grow in Sn-Pb alloys, and the composition-growth rate dependence of the transition from eutectic to dendrites-plus-eutectic. This prediction was based on work on organic eutectics. The model on which the prediction was based assumed that there was no temperature gradient in the system, a condition approximately satisfied in the study of organic eutectics2-5 but not in the growth of metallic alloys. Mollard and Flemings6,7 have recently reported experimental results for Sn-Pb alloys in which they have located the transition from eutectic to eutectic-plus-dendritic growth. The experiments were performed using large temperature gradients (65 to 515 deg per cm), so that the assumption of zero gradient on which the predictions of Hunt and Jackson' were based does not apply. It is not surprising therefore that the predictions' were not born out by the experiments.7 In the present work, a modification of the model used by Hunt and Jackson is presented which takes into account the temperature gradient. The modified form of the theory predicts the transition from eutectic to eutectic-plus-dendritic growth in terms of the composition, growth rate, and temperature gradient. Good agreement with the experimental data of Mollard and Flemings7 is obtained. THE HUNT-JACKSON MODEL The model used by Hunt and Jackson' to predict the transition from eutectic to eutectic-plus-dendritic growth was based on the assumption that dendrites grow ahead of a eutectic interface only if they grow faster than the eutectic interface. Analytic expressions for the growth rate of dendrites and the eutectic in Sn-Pb alloys were obtained by fitting experimental data with equations whose form was indicated by theory.

Jan 1, 1969

By E. Manev

Thin aqueous equilibrium film studies and surface tension measurements on a mixed surfactant system consisting of polyethylene oxide (a model frother) and potassium ethyl xanthate (a model collector) enable the interaction between the two surfactants at the air/solution interface to be elucidated. For the film containing the non-ionic frother, the interface was charged and addition of low concentrations of xanthate acted as a common electrolyte and reduced the thickness of the film inducing rupture. However, at high xanthate collector concentrations, the negative charge xanthate was found to interact with the non-ionic and caused a build-up of negative charge at the air/solution. Higher frother concentrations were necessary to produce non-rupturing thin films upon increasing the xanthate concentration.

Jan 1, 1992

By B. D. Cullity

A distribution of residual stress after plastic elongation is proposed, in which the bulk of the material is strained in compression and a very small portion in tension, This distribution is shown to account both for the X-ray observations and for the effect of plastic straining on magnetic losses in silicon steel. The regions left in compression are tentatively identified with the interiors of the sub-grains revealed by the electron microscope. THIS paper is concerned with the general problem of the nature of the residual stress which is produced in metals by plastic elongation. A particular stress distribution will be suggested which accounts for the main X-ray diffraction observations which have been made. It will also be shown that certain magnetic measurements made on silicon steel can be understood in terms of this stress distribution. X-RAY OBSERVATIONS Uniform straining of a crystal lattice (macro-strain) causes a diffracted X-ray beam to shift its position, and nonuniform straining (microstrain) causes line broadening. If a bar of metal is plastically elongated in the longitudinal x direction and then unloaded, diffracted X-ray lines are observed to be both shifted and broadened.'-= Although the observed line shift indicates the presence of macro-strain, experiments have shown that no macrostrain, in the usual engineering sense of the term, exists.5"7 For example, removal of a layer from one surface of a stretched and unloaded bar does not produce curvature in the remainder of the bar 5'7 Fig. 1 shows the variation of lattice strain in the x direction, as determined from X-ray line shifts, with the applied stress in the same direction. The curve ABC is the normal stress-strain curve of the material, AB being the elastic portion and BC the plastic. In the elastic region AB, the strain measured by X-rays, called the lattice strain, and the strain measured mechanically are both proportional to the applied stress, and both return to zero when the applied stress is removed. Above the elastic limit the lattice strain would be expected to continue to increase along the line BD. Actually, it increases less rapidly with respect to stress, or even decreases, as shown by BE. If the applied stress is then decreased, the lattice strain decreases along EF, which is parallel to AB. As a result, there is a compressive residual lattice strain FA after unloading. STRESS DISTRIBUTION. Since a stretched and unloaded bar does not contain macrostress, it follows that the observed line shift must be due to a special distribution of mi-crostress. Such a distribution is shown in Fig. 2, which shows the variation of the stress u, across a stretched and unloaded bar. The material is assumed to consist of two kinds of regions: regions C, stressed more or less uniformly in compression, comprising the bulk of the volume of the material and responsible for the observed diffrac-

Jan 1, 1963

By Peter T. Chiang

A brief literature review on metal separations by ion exchange and solvent extraction of their thiocyanate complexes which are practiced in analytical chemistry as well as in industries was performed. Owing to the poor stability of free thiocyanic acid in acidic aqueous and organic media, technical and environmental problems which cause high thiocyanate consumptions often arise during the practice of the separation processes. This prompted the conducting of a second and more thorough literature review on the chemistry of thiocyanic acid. The objectives of this undertaking are to compile and interpret literature data on the physical properties and chemical reactions of thiocyanic acid, thus providing a clearer understanding of the causes of these problems and giving options as to how to minimize them. The best answer found for carrying out the separation processes is to keep the temperature, thiocyanic acid concentration and total acidity as low as practical.

Jan 1, 1984

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

By Ronald F. Balazik

[This Bureau of Mines study is intended to identify and evaluate potential effects of impending large-scale U. S. rail line closings (abandonment) on domestic nonfuel mineral industries. This is the first nationwide study of rail abandonment impacts focused on nonfuel minerals. The analyses presented is based principally on a survey of 200 rail freight records and on statistical tests that correlated 2,000 points in the Bureau's Mines Industry Location System (MILS) with 700 prospective abandonments throughout the United States. The conclusions derived from the analysis can be useful in evaluating proposed national rail abandonment policy rind legislation regarding nonfuel miner it shipping. Among these conclusions are the following: (1) Certain mineral materials (especially fertilizers) are likely to account for a large percentage of the rail traffic affected by abandonment in the next few years, but the total tonnage- involved will be small; (2) abandonment will adversely affect some mineral shippers, particularly local smart haulers; and (3 abandonment could significance reduce the opportunity to develop new resources or reopen defunct mining facilities. Despite these problems, however, the data examined in this study do not indicate that current abandonment trends will cause widespread disruption 01 domestic nonfuel mineral shipping.]

Jan 1, 1980

By R. L. Segall

AN unusual thermal etch figure in copper is described and an explanation in terms of twinning is suggested. A flat polycrystalline specimen of OFHC copper cut from a rolled sheet was electro-polished in orthophosphoric acid and annealed at 950°C in a vacuum of approximately 10-3 mm Hg for 2 hr. The specimen was found to be thermally etched, the markings on the surface being consistent with the assumption that they were the traces of the (111) planes which are developed preferentially because they have the lowest free energy. However, on one grain (the grain shown in Fig. 1) the traces formed an almost regular pentagon and at first sight it seemed unlikely that they could all be (111) traces. These traces were studied further because it was thought that they might be a type of growth spiral. A fringe pattern showed that this was not so, the grain being sensibly flat and the only features having steps were the striations and the faint curved line passing out from the center of the pentagons. To obtain some additional information, the specimen was deformed in tension. The effect of the stress was first to cause the appearance of lines running from the centers to the apexes of the pentagons and then to tilt the five segments so formed. At a much greater stress, appreciable slip appeared on the grain; these effects can be seen in Fig. 2. The micrograph was taken at a fairly late stage in the deformation and the tilting is quite marked. The magnification is the same as in Fig. 1, and although some slip can be seen it could be observed better by varying the illumination and using higher magnifications. In each segment of the grain, slip (which takes place on the (111) planes) was parallel to the side of the pentagon in that segment. The marked changes in direction of slip from segment to segment seemed to be incompatible with the presence of a regular array of subgrains. These results suggest that some of the five segments were twins. If this is so, since the twinning plane in copper is the (111) plane, the radial lines must be traces of the (111) planes on the surface. From the symmetry of the striations about the radial lines, these planes must be almost perpendicular to the surface. The angle between <III>directions in face-centered-cubic copper is 70&apos;32&apos;. If, in Fig. 3, OAB (triangle 1) is taken as matrix and OA, OB are (111) planes viewed edge on, then AB is in the correct direction to be the trace of either of the other two (111) planes on the surface. If triangle 2 is the twin (about the (111) plane perpendicular to the surface and containing OB) of triangle 1, then once again it can be shown that all lines are traces of (111) planes. Similarly, triangle 3 is the twin of triangle 2, 4 of 3, and 5 of both 4 and 1. (The sequence is, of course, quite arbitrary.) However, if this were the case there would be a discrepancy of 7&apos;20&apos; to be accounted for. It is suggested that the faint curved line passing outward from the center of the pentagon represents either a low angle boundary or a sixth small twin. The slight step shown by the fringes at this line might be an indication that the former is the case. This explanation does not account for the coincidence of obtaining a grain whose surface must be so close to (110) and obtaining the curious twinning described previously; it would be of interest to find a specific mechanism for this.

Jan 1, 1958

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, roofing granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of roofing, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural fines available. On the other hand, California manufacturers of asphalt products other than paving utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, slate, and other nonmetallic minerals as filler, mainly for roofing and flooring. Also, about 500,000 tons of roofing granules is produced in California, most of which goes into roofing manufacture in California. In addition, a significantly large and growing tonnage of relatively coarse mineral aggregates are used on low-angle, built-up, asphalt roofs to produce an attractive surface and offer protection against the elements. Nearly all minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of these commodities could be utilized in some use categories.

Jan 1, 1966