Search Documents

By Don Rose

In the USA the cost of steel ribs for tunnels approximates $100 million each year. European practice has long since abandoned heavy steel ribs for tunnel support, and tunnel coats in Europe (normalized for wages) are about half the costs incurred in the USA. A feeling has existed for some time that the USA practices of supporting tunnels with heavy steel ribs have been overly conservative. The USA practice is based on rock load coefficients by Karl Terzaghi. In 1946, Karl Terzaghi published a tunnel rock classification system (Terzaghi, 1946), with the rock loads on tunnels predicted for each class of rock. No data on real rock loads were presented by Terzaghi and his rock load coefficients may have been largely intuitive. His classification system and associated predicted rock loads have been widely used in the USA. Each rock class, taken from Terzaghi's classification system, is assumed to generate loads of loosened rock resting as dead load. The dimensions of the loosened rock are described by rock load coefficients multiplied by the tunnel diameter. The resulting rock loads are used by design engineers, contractors and agencies to size supporting steel ribs. Terzaghi clearly stated that he had conservatively assumed high rock loads for his classes 4, 5 and 6 to take a presumed effect of groundwater into account. If the tunnel was not affected by ground- water, Terzaghi stated those rock loads should be reduced by 50 percent. Twenty two years later Tor Brekke (1968) wrote a paper clearly showing that based on observation of more than 250 tunnels groundwater does not affect tunnel rock loads. In 1969, Deere, et al., published measurements made on a number of tunnels, and a well-known curve was drawn by Deere to illustrate Terzaghios coefficients graphically. Deere's text stated that Terzaghi's predicted rock loads were too high and should be reduced. Cording and Deere (1972) more recently published data indicating that very large real rock caverns and chambers were being successfully built using rock bolts, which can take only a very limited rock load, thus indicating that real rock load is much smaller than Terzaghi or even Deere predicted.

Jan 1, 1982

By M. F. Hochella

Transmission electron microscopy (TEM) and energy dispersive X-ray (EDX) analysis have been used to study the mode of occurrence and mineral associations of gold in partially oxidized high grade gold ore from the Carlin sediment-hosted deposit. Rounded.gold particles have been observed that range in size from 0.03 to 0.1 p.m (300 to 1000 A) in diameter. The gold is associated with maghemite h-Fep3l and a K-Al-Si-bearing phase that is suspected to be illite. Detailed descriptions of gold and its mineral associations in 'Carlin-type' gold deposits are critical not only to understanding the mechanism of fluid transport and precipitation of gold, but also to developing improved metallurgical techniques for the recovery of gold from refractory ore. Direct observation of gold in unoxidized ore is rare due to its relatively high degree of dissemination and low average bulk concentration which averages 9 ppm according to Radtke (1). Hausen and Kerr (2) observed 1 to 5 p.m grains of gold directly in oxidized ore but these microscopically visible particles account for only a small percentage of gold present in the ore. The samples used in this study were selected from individual beds of high grade, partially oxidized ore (4.55 oz/ton or 156 ppm gold) that were collected in the Main pit of the Carlin mine. The samples were collected from several thinly laminated carbonate micrite beds within the top 50 meters of the Roberts Mountains Formation. The carbonate micrite has been altered by hydrothermal fluids to a calcite-absent, moderately silicified rock referred to as alteration zone #3 by Bakken and Einaudi (3). Based on petrographic and SEM studies, the samples contain carbonaceous matter, and both pyrite and iron oxide pseudomorphs after pyrite. The oxidation of pyrite may be a pro-duct of deep weathering, in which case limited remobilization of gold may have occurred. TEM sections of the rock were prepared by first embedding small chips in low viscosity epoxy. The epoxy blocks were cut with a Reichert Ultracut E ultramicrotome, producing thin sections less than 0.1 p.m thick. The sections were examined with a Phil-lips 400ST TEM at 120 keV in both imaging and selected area diffraction modes. Native golci*was easily detected in TEM bright field images due to the large electron density contrast between gold and all other phases that are present (Figs. 1 and 2), Gold was positively identified with high spatial resolution EDX analysis in the transmission electron microscope, although selected area diffraction of individual grains was not successful EDX analyses of the platy and massive minerals immediately surrounding the gold particles typically indicate the presence of Si, AI, K, and Fe, However, the d-spacings derived from selected area diffraction of these polycrystalline masses (as, for example, in Fig. 2) give an exact match for maghemite. As a result, there is no diffraction information to identify the K-AI-Si-bearing phase(s). The lack of a diffraction pattern could be due to either electron beam damage or to a poorly crystalline phase(s).

Jan 1, 1987

By Jeffrey D. Winterton

Keywords: Copper, ion exchange, sulfonic acid, bis-picolylamine, ion exchange modeling, ion exchange kinetics As part of an investigation into the feasibility of using ion exchange resins to recover copper from aqueous waste streams generated during the manufacturing of semiconductor devices, the uptake of copper onto two ion exchange resins was investigated. The resins studied were DOWEX G-26, a standard gel type sulfonic acid resin, and DOWEX M4195, a macroporous chelating resin with a bis-picolylamine functional group. The equilibrium and kinetic behavior of the uptake of copper were investigated over a range of copper concentrations with constant sulfate concentration and different levels of acidity. The homogeneous structure of the G-26 resin yields equilibrium relationships that fit the Langmuir equation, and equilibration times of less than 30 minutes. The uptake behavior of M4195 is complicated by the need to absorb co-ions to maintain electroneutrality, resulting in uptake profiles that change character with increasing copper concentrations, and extended equilibration times.

Jan 1, 2005

By N. T. Mirafuente

The device called "Dynastat" which is described in this paper provides in situ borehole measurements of dynamic and static parameters for use in a wide range of design applications. In the dynamic mode, the Oynastat allows measurement of shear and compressional wave velocities. From these velocities in situ dynamic Young's modulus and other dynamic elastic parameters can be calculated. In the static mode, the device allows measurement of load versus deformation from which in situ static Young's modulus can be determined. Information on in situ horizontal stress fields can also be estimated from the load deformation curves. In both mining and civil engineering applications, in situ measurements of material properties are indispensable for accurate evaluation of design problems. Laboratory dynamic and static test measurements in comparison to in situ measurements are often misleading due to difficulties in obtaining undisturbed samples and in accounting for effects of discontinuities, etc., for mass properties. The authors contend that among in situ borehole measurements, the method employed with the Dynastat is the most accurate and detailed technique of measurement. The Dynastat employs the crosshole method of shear and compressional wave velocity measurements and also performs as a borehole jack to obtain load-deformation relationships of materials at exactly the same location at depth in boreholes.

Jan 1, 1976

By Michael Drozd

"The operation of an activated charcoal system has five separate unit operations. These unit operations have common points for CIP, CIL and CIS system, which vary widely in application.The unit operations are:a. Absorptionb. Desorption (Stripping)c. Acid Washingd. Reactivatione. Carbon Handling (carbon transportation, sizing, dewatering, etc.)Cost optimization starts with the basic operating parameters (design philosophy) set down at the time of engineering design. These parameters undergo almost immediate change due to site specific ore requirements, throughput changes, operator requirements or reagent availability.Activated charcoal is sometimes viewed as simple, uncomplicated reagent that requires not optimization. To some extent, this statement is true, but under most circumstances, if the time necessary to optimize the use of activated charcoal is available, the effort is rewarded with significant savings. CPL-Carbon Link has embarked upon a program of supplying technical support with its activated charcoal. Several operations in the United States have undertaken to have CPL-Carbon Link do an operational survey to determine if potential savings are possible. CPL-Carbon Link has offered to do these surveys for projects that are clients or simply would like to have CPL-Carbon Link review their operation. The information accumulated by CPLCarbon Link is being used to attempt to fashion industry standards so that a common reference point can be established for activated charcoal usage."

Jan 1, 2008

By F. C. Wagner, E. P. Klier, D. E. Nulk

The presence or absence of plastic strain at a cleavarage surface is a question of much importance, and upon its answer depends future possible theoretical work. To investigate this question back-reflectinn X ray patterns were obained on the cleavage facets of ferrite grains. The test set-up consisting of FeK colli- mated radiation, single grain material and stationary cassette and specimen will not lead to a diffraction pattern, in general, but is an ideal arrangement for the exami-nation of surface effects. A pattern taken on hydrogen purified

Jan 1, 1949

By Y. Nakahiro

The removal of heavy metal compounds from a synthesized waste cyanide solution is achievable by a precipitation-flotation method. However, the differential separation of constituting metals by this method was thought to be very difficult. The present author found that addition of ferrous salt to the synthesized waste cyanide solution of cadmium and copper can modify the separation characteristics of these metals. In this paper, the separation of cadmium from copper in the synthesized waste cyanide water by the precipitation-flotation method is discussed. This differential flotation uses ferrous salt as a precipitant and sodium oleate as a collector. Based on a series of fundamental flotation tests, actual differential flotation tests were made. The separation of cadmium from copper in the synthesized waste cyanide water was found to be satisfactory. This method can be effective for the removal of difficult-to- separate colloidal precipitates from liquids by the sedimentation method, provided the applicability of this method to the separation of the other metals is promising. This consists of the intensive studies which have been conducted at author's laboratory.

Jan 1, 1980

By M I. Jeffrey, J A. Rumbal, D M. Hewitt

Ion chromatography utilising an anion exchange column and UV detection has facilitated an improved understanding of sulfide mineral leaching in cyanide solutions. By analysing for sulfide, sulfite, thiocyanate, thiosulfate and metal cyanides it is possible to show that chalcocite dissolution is a non-oxidative process in which copper cyanide and sulfide ions are formed in solution. Further, the homogeneous oxidation of the sulfide ions by dissolved oxygen is slow, but catalysed by a surface of lead sulfide or pyrite. Polysulfides may also be formed as an intermediate oxidation product and these undergo further reaction to produce thiocyanate, thiosulfate and sulfite. The leaching of copper from a pyrite concentrate sample is shown to be rapid, and accompanied by significant iron dissolution; however, the iron is not believed to be from pyrite, pyrrhotite or chalcopyrite. The rate of iron leaching and cyanide consumption is reduced by maintaining low cyanide and high oxygen concentrations. Preoxidation or the addition of lead(II) ions does not reduce the iron dissolution from this pyrite concentrate.

Jan 1, 2007

By Eugene Mirsky, Eloy Ramos, May ElKhattab, John Wise, Terrence Carroll, Jose Torres

In 2017, Nicholson Construction Company completed a $72.1 million design-build contract for Miami Dade Water and Sewer Department to replace an existing 54-inch diameter pre-stressed concrete force main that runs from the Virginia Key Central District Wastewater Treatment Plant, under the Biscayne Bay at Norris Cut, to Fisher Island. In order to install the new sewer pipe below the bottom of Biscayne Bay, a tunnel boring machine (TBM) was launched from a 42ft diameter and 89ft deep shaft on Virginia Key and a precast segmentally lined tunnel was constructed towards a 28ft diameter and 72ft deep retrieval shaft on Fisher Island. Both shafts were constructed through sand and highly permeable limestone, primarily the Fort Thompson Formation which is part of one of the most permeable aquifers in the United States and two different techniques were used to ensure a water-tight shaft at each end of the tunnel drive. The launch shaft structure was built using the secant pile technique, wet excavation and a tremie plug. For the tunnel break-in a soil freeze block was installed after the ground was treated with low mobility grout. The retrieval shaft was built using the Deep Soil Mixing (DSM) technique and excavated in the dry. Precedence of any other structure built this deep through hard layers (UCS over 3,000 psi) using this technique was not found. This case study addresses the challenges of constructing watertight underground structures in highly porous ground for launching and retrieving a TBM. Design challenges from complex asymmetric loading, selection and comparison of the construction techniques, the installation and excavation of both shafts, and their performance are also discussed herein.

Jan 1, 2018

By Howard W. Kilau

The U.S. Bureau of Mines is investigating surfactants added to water sprays to enhance the control of dust during coal mining operations. The objective of the present work was to establish the general applicability of adding sulfate ion to anionic surfactant solutions in order to improve wetting action. This was pursued through laboratory wettability testing of four anionic surfactants and one nonionic surfactant in combination with various concentrations of sulfate ion. The experimental results demonstrated that the addition of sulfate ion enhanced the wetting characteristics of all the anionic surfactants when applied to hard-to-wet coals, while easy-to-wet coal showed more complex wetting behavior. Sulfate ion in the presence of nonionic surfactant enhanced wetting only slightly or not at all. Surface tension measurements of the dilute aqueous surfactant-sulfate anion solutions indicated this property was not important in coal-wetting phenomena, as long as the value was below the critical value for coal. Sulfate ion helps surfactant reduce surface tension but primarily appears to affect wetting action by altering the adsorption characteristics of surfactant on the coal surface.

Jan 1, 1990

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines has shown that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum-group metals (PGM) is technically feasible. The purpose of this work was to investigate the chemistry of the dissolution of PGM in cyanide solutions in more detail. Where possible, samples of pure, elemental PGM powders or foils were used instead of automobile exhaust catalysts, because of their greater purity. Ultraviolet spectra revealed that Pt and Pd were solubilized as the square planar tetracyanometallate (II) complexes, while Rh was solubilized as the octahedral hexacyanorhodate (III) complex. This explained the poor recovery of Rh from solution by carbon adsorption, solvent extraction, and ion exchange observed in earlier research, because of the higher anionic charge and size of the octahedral complex. Leaching rate studies showed that the rate of solubilization was greatest for Pd, followed by Pt and Rh. Although the rate of chemical reaction was the controlling step for the dissolution of elemental Pt and Rh samples, the rate of pore diffusion was rate limiting for PGM in catalyst samples.

Jan 1, 2010

By Robert F. Kehrman

As with many new technologies, the rapid growth in solution mining for uranium has created uncertainties regarding the environmental impact of mining operations. In solution mining, the largest area of concern is the impact of the process on the quality of ground water supplies. As a result, a rapid and reliable technique of detecting lixiviant excursions is desirable. Such a method would replace the periodic sampling technique and should provide a more or less continuous monitoring method. To this end, resistivity techniques were evaluated as an alternate means of tracking lixiviant movement. A program was devised which had five specific tasks. These were: (1) evaluation of the techniques, (2) development of the most promising technique or techniques, (3) field testing of the techniques, (4) testing of the BuMines probe, and (5) reporting. The result of the analytical and field work is that various resistivity/ resistance techniques do provide a means of detecting lixiviant movement in Northern Wyoming. Surface and downhole galvanic surveys and controlled source audio magnetotellurics (AMT) were evaluated. All three techniques showed some degree of success.

Jan 1, 1979

By Michael G. Strominger, Anthony E. Gross

The development of precious metals ore agglomeration with a cement binder, by the U.S. Bureau of Mines, has allowed the economical heap leaching of low grade gold ores (<0,05 oz/ton) over the last decade, Even with the Bureau of Mines technology, numerous operations continue to experience channeling and blinding problems. A research project was undertaken at Nalco Chemical to address situations where improved agglomeration is needed, By increasing the incorporation of fines into the agglomerates,the segregation of ore by size which occurs from handling will be reduced and channeling minimized. A stronger agglomerate will reduce fines migration during leaching and prevent blinding of the heap, Both of these changes will give an even flow of barren solution throughout the heap and give solution contact with all of the ore. This paper presents the development of polymeric agglomeration aid, Nalco 9760 which has given a higher rate of and a higher total gold recovery in plant evaluations.

Jan 1, 1990

By D. K. Sengupta, T. K. Rout, A. R. Prasad, B. P. Singh

The filter cake from the vacuum drum filters of a uranium ore processing plant still contains some leach solution. If the filter cake is not efficiently washed the associated leach solution is lost. Therefore, it is necessary to produce a filter cake that is permeable enough to allow efficient washing. The dewatering characteristics of the solid-liquid system must be improved to obtain flocs with sufficient strength to withstand the suction pressure of the filtration system. To facilitate efficient filtration with minimum cake moisture, studies were undertaken to improve the dewatering characteristics of the cake using different types of flocculants and surfactants. In these studies, flocs were formed with anionic, cationic or nonionic flocculants. The best performance was obtained with a low cationic high molecular weight flocculant. The filtration parameters, namely, capillary suction time, cake resistance, cake permeability and final moisture content of the filter cake, are improved by using a combination of flocculant and nonionic surfactant.

Jan 1, 2002

By Christopher McElman

Real-time mine management solutions have evolved over time from closed, proprietary solutions, to a "system of systems" that may include a wide variety of off-the-shelf components and technologies. Modular Mining Systems has embraced open standards for their NextGen products to bridge the technology gaps between these systems. However, the remaining logical gaps must be overcome, in order to achieve truly seamless integration between discrete systems. When dealing with volatile real-time management problems, the effectiveness of business process modeling and middle-ware can break down. Scientific principles of military command and control applied to mining domain help to achieve better alignment and reach the highest level of integration. The combination of open standards and off-the-shelf hardware and software with a deliberately structured command-and-control approach provides a clear evolutionary path from ad-hoc connected systems towards real-time management of a seamlessly integrated digital mine.

Oct 1, 2009

By K. Sasaki, H. Miyakoshi, K. Mashiba

A ventilation analytical system adapting nodal pressure method using skyline modified Choleski&apos;s decomposition scheme for network-flow analysis and a new practical system to estimate various thermal air conditions has been developed. The quasi-linear equations for solving steady-state network airflow have been described using the connective function in general forms. The skyline modified decomposition scheme has an advantage on rapid convergence and the sake of computer memory space com- pared with other schemes. The key part of the analysis for climatic conditions through network airways is how to estimate the temperature of the airway rock-surface with partly or full wet condition. A practical and simple solution without any iterative calculations for its estimation has been proposed. This new solution is applicable to practical ranges of airflow temperature, humidity, rock thermal properties and wetness. The present analytical sys- tem have been successfully applied to a ventilation simulator named "M1VENA"developed by authors.

Jan 1, 1996

By S. R. Reddy

Thennodynamic properties of several quaternary systems are calculated using our recently modified Margules equations. The modified Margules equations are expressed up to infinite order in the vicinity of solvent. Quaternary system of one solvent and three,solute partials are derived. First order interaction coefficients of binary, ternary and cross -interaction parameters of quaternary system are used to&apos;evaluate the partial functions. In the original fonn of Margules equations,derived partial functions are convergent and same &apos;as Unified ,Interaction Parameter Fonnalism. But considering up to infinite order of the Margules coefficients, the functions are divergent, in order to overcome this restriction, Margules equations are modified to get consistent equations. Derived partial functions are thennodynamica Hy consistent with Maxwell and Gibbs Duhem relations. The derived logarithmic activity coefficient of the solvent and solutes are consistent with the ternary systems. The calculated data, ie., activity coefficient values of nitrogen and interaction coefficients are in good agreement with the data of Fe-Cr-V -N. Fe-Ni-V -N, Fe-Cr-Ta-N and Fe-Ni-Ta-N systems.

Jan 1, 1999

By J. S. Tosh

An equilibrium study of the system potassium carbonate, potassium bicarbonate, carbon dioxide, and water has been conducted with solutions of 20-, 30-, and 40-percent equivalent potassium carboaate concentrations. These equilibrium data cover the operating range of the hot carbonate scrubbing system for removing carbon dioxide from gas mixtures. Such data are necessary to establish the limits of purification and are used to design absorption and regeneration towers. Values of K in the relationship K = (KHCO3)2/(K2CO3)PCO2 were determined for higher temperatures of 70" to 140° C. and greater concentrations, I 20 to 40 percent, than employed by previous investigators. For the 20- and 30-percent concentrations, K is constant at a given temperature; thus, once K has been determined the equilibrium pressure of carbon dioxide can be calculated for any conversion. Variation of & values with changing conversion was observed with the 40-percent solutions, so that equilibrium calculated pressures are less reliable from average K values.

Jan 1, 1959

By William H. Shockley

[SECRETARY&apos;S ]NOTE.-The following notes, arranged and edited in this office, but not yet revised by the author, were placed at my disposal with much modest hesitation (due to their incomplete and fragmentary character), upon my earnest request, and my argument that such recent and trustworthy data concerning a new and important mining industry ought not to be withheld from our Transactions, simply because they are not sufficient to constitute a, complete academic treatise on the subject. This argument is recommended to the attention of many other members, who are waiting for the opportunity to contribute something "monumental" to our Transactions. In a number of instances, death has nulli¬fied this ambition, and the intended "monumental" contribution has turned out to be an obituary notice by the Secretary, instead of a valuable record of the professional experience thus hopelessly lost to the world.-R. W. R.] The official publications of the the Russian Government give fairly complete statistics of the dredges operated in the Empire; and in a recent English bluebook, Mr. Cook&apos;s report on Siberian Trade presents a brief account of dredging in Siberia. The data in Table I. (not given by Mr. Cook) have been taken from the Gold Mining Messenger (Russian) for July, 1905. These interesting statistics, though incomplete, show that the Yenisei dredges are working on poor ground and yield small returns. According to report, but few yield a profit exceeding 10 per cent. per annum on the capital invested. In the summers of 1904 and 1905, I traveled in the Urals as far north as lat. 61° N., long. 61° E., on the the Lozva river, a part of the vast system of the 01) river. This clear-water stream starts from the summits of the Urals at an altitude of 4,000 ft., and flows through a flat country, densely wooded with larch, spruce, pine, fir, birch and poplar. The river is full of fish, and is navigable for good-sized steamers as far as Ivdell. Winter lasts from early November to late April, the temperature rang¬ing from -60° F. to a summer maximum of 90° F. The rain¬fall is 20 in.. The climate is healthy, although mosquitoes,

Jul 1, 1906

Alexander Forsyth, Southport, Me. (communication to the Secretary): In Mr. Irving&apos;s able and interesting paper he describes minutely the appearance of the wolframite and its association with the refractory siliceous gold-ore. He also describes this gold-ore, but fails to mention the important pockets of metallic gold found in the Lead City occurrence of it. I use the term " metallic " in preference to the more usual " free," for it has been found that this gold is not easily amalgamated. Metallic gold is comparatively rare in the refractory siliceous gold-ores of the Black Hills; hence its occurrence in considerable amounts in the Lead City wolframite district deserves notice. I possess a beautiful specimen from the Harrison mine. It is a lump of drusy, granular ore, about 6 in. in diameter. The gold .is " shot" through it in large and small pin-heads; and in two specially oxidized areas, each about 11/2 in. in diameter, it is peppered full. The famous " Grantz strike," made in the Lead City wolframite locality, produced many beautiful gold specimens. This district affords an excellent example of the repeated discovery of new mineral values upon old ground. By reason of its proximity to the Homestake vein, this wolframite deposit was inevitably traversed many times by experienced geologists, mineralogists and mining engineers, who evidently must have thrown aside, with no thought of wolframite, the lumps of " black iron " lying about. I have the admission of an able geologist that, six months before the wolframite was discovered, he visited some of the very mines where it occurred, and passed it by as magnetic iron-ore. At the time of the discovery, the mineral was scattered over the gold-mine dumps in no small quantities, having been culled as worthless out of the gold-ore. It remained for

Jan 1, 1902