Search Documents

The mining industry is the largest source of foreign income for South Africa. It is also the main source of employment in the country and, as an industry; it is also one of the largest. Due to the labour-intensive nature of the industry, labour costs in South African mines make up nearly 50 per cent of the total mine cost. It is thus imperative to have optimum labour planning and labour management systems in place.The focus of this study was to investigate current underground labour-planning models. It is shown that there are serious limitations. The range between an oversupply and undersupply of labour can be as high as ten per cent. A new system was therefore developed to ensure a constant labour demand and supply on a daily basis. One of the main objectives was to determine the existing labour supply range and thus the requirements to fill the undersupply. For this purpose, a specific methodology was designed to capture and process all the relevant information. Mine personnel was involved throughout the entire process to ensure ownership of the new model. This buy-in was achieved through planning workshops, interactive presentations and discussions. The improved frequency of daily blasts validated the new system by providing the correct amount and mix of the labour force. The new labour-planning model was then extended to optimise revenue. Implementation on a mine resulted in increased income of R95 million.

Dec 6, 2010

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The subsurface soil profile consists of up to 50 ft of a soft organic silty clay layer that is very vulnerable to scour, underlain by a deep deposit of hard sandy clay. Foundation construction in the Potomac River required the use of cofferdams to allow structural concrete work to be performed in the dry. This paper will the present the types of cofferdams used to construct the foundations for the WWB replacement project. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over a navigation channel in relatively deep water. Foundation construction included the installation of 48? to 72? open end steel pipe piles and cast-in-place concrete pile caps. To achieve the desired bridge appearance, pile caps were required to extend below the water surface and below the existing river bottom in shallow water locations. Conventional steel sheet pile cofferdams with tremie concrete seal were used to construct fixed span, shallow water piers. Selection of deep water bascule span foundation cofferdams was governed by several factors including contraction scour, environmental considerations and cost. Potomac River cofferdams, i.e., relatively shallow depth cofferdams that are supported by the foundation piling were selected. This cofferdam system provided a shallow profile which minimized contraction scour and the amount of filling in the river. Design issues include load selection and cofferdam stability in very soft alluvial soils. Construction issues include erection sequence, tremie concrete mix design and placement procedures.

Jan 1, 2013

By G. Capobianco

"The coal industry is an important part of Canada's economy - as an energy source, employer, and generator of export earnings. Coal comprises 71% of our fossil energy and with rapidly advancing handling and burning technology will clearly play a major role in our national energy mix, eventually as synthetic gases and liquids.International coal markets are very competitive and Canada is disadvantaged by long rail hauls to port, and a heavy tax burden. However, high mine productivity has allowed us to increase our markets.Currently, domestic markets are dominated by coal use for electrical generation, a market with significant growth opportunities.Strong growth is expected in export thermal markets, while metallurgical coal demand is projected to show little or no growth in the medium term. IntroductionThe coal industry is a vital part of the Canadian energy scene .• Coal supplies 17% of Canada's energy.• On a per capita basis, Albertans use more energy in the form of coal than they do oil and gas.• The value of Canada's exports of coal last year was equal in value to all the cars we imported from Japan.• Coal is our largest single export to our seco nd largest trading partner, Japan.• The value of coal produced in Canada exceeds the value of any other single mineral produced in thi s country.• In Alberta, the safety record for coal mines is on a par with that of department store clerks.• The coal industry employs about 25% of the total number of people employed in all metal mines in Canada, directly and indirectly accounting for about 50 000 jobs.Coal comprises 71% of Canada' s hydrocarbon energy resources on a crude oil equivalent basis . This is more than double our oil sands resource and dwarfs our conventional crude oil and gas resources (Fig. I). In the short term, coal as a solid fuel plays a significant part in the Canadian energy scene. In the longer term, coal, in the form of electricity and eventually liquids and gases, has a tremendous role to play. In 1986, Canada produced 57.8 million tonnes, slightly down from the record high of 60.8 million tonnes in 1985. Our exports in 1986 were 26.0 million tonnes, a growth of 53% in three years."

Jan 1, 1988

By W. J. Birch, A. Wetherelt

The scaled-distance model for blast vibration analysis is the standard method employed throughout the surface mining and quarrying industries to model Peak Particle Velocity (PPV) data. Although empirical, the method is widely accepted and through the simplicity of its application and ease of graphical verification is set to remain a popular option. The validity of the technique relies principally on the fundamental parametric assumption that blasting data is normally distributed. Throughout the evolution of scaled-distance modelling, this is an issue that has most often been presumed rather than proven (most likely due to the tediousness of the calculations involved). In the few cases when normality has been given some degree of consideration, the result has been the product of a simple visual inspection of frequency distributions: clearly unsatisfactory. However recently the soundness of this assumption has been brought into question, with obvious connotations for blast modelling in general. This paper considers this fundamental issue and seeks to investigate the normality hypothesis within the blasting context through an in-depth statistical analysis of what possibly can be described as an ‘ideal’ blasting dataset. This being a rare case study concerning an opencast coal site in England, where for the entire life of the site every single blast was monitored and recorded through the use of permanent monitoring stations. This has provided a unique ‘total population’ dataset of considerable size from which the assumptions of normality are put to the test.

Jan 1, 2005

By Nien-Yin Chang

The contemporary seismic response analysis of structures using a finite element analysis code requires six elastic spring constants to address the six degrees of freedom ground/foundation contribution to the response of a structure to earthquake shaking. However, the ground response is nothing but linear. Thus, it is critical to address the effect of the nonlinear ground response to the performance of structures under strong earthquakes. This study specifically addresses the effect of pile foundation on building vibration using finite element analyses. The effect of single pile was first investigated and the load was applied at the pile head using the single-degree-of-freedom load at a time, including three translational loads in the x, y and z directions and three moment loads about the three respective axes. In this study, the coupling effects between two or more different loads were not investigated. A load is increased monotonically to investigate the nonlinear behavior of pile under various loads. The Mohr-Coulomb model was used to represent concrete. To explore the effect of soil models on the nonlinear spring functions, the following constitutive models of soils were used: linear elastic, Mohr-Coulomb model, Cap model, modified Cam-Clay model, and Duncan-Chang hyperbolic model.

Jan 1, 2007

By Vinay Kumar

The disposal of large quantities of electronic scraps generated world wide is causing not only environmental problem but also loss of resources. Therefore, R & D efforts have been made to develop a suitable process for extraction and separation of metals viz. copper, zinc, cadmium and nickel expected from the leaching of e-scraps using solvent extraction process. Different process parameters viz. pH, aqueous to organic ratio, kinetics of extraction, extraction isotherm to establish stage requirement for extraction in continuous mode etc have been studied to optimise the condition for the separation of metals. The studies showed the selective extraction of copper after iron precipitation from the sulfuric acid leach solution of e- wastes containing ~1.0 g/L Cu and minor impurities with 2-hydroxy-5- nonylacetophenoneoxime (LIX 84) above pH 2.0 in single stage. A scheme for separation of cadmium, zinc and nickel has been proposed using di(2-ethylhexyl) phosphoric acid (D2EHPA) under controlled pH of the aqueous solution. The order of extraction was found to be Zn> Cd> Ni.

Jan 1, 2009

The term slag has been used to define a wide variety of material including mine spoil and slag produced at steel plants. The present paper is concerned only with the non-metallic alumino-silicates developed simultaneously with iron in blast furnaces.The control of iron quality by slag has long been appreciated but here aspects of slag control based on concurrent iron production are indicated. Consideration is given to the basic composition of slags relative to the type of allotrope required. Up to a point, the plant conditions, under which a particular slag type is processed, have some effect, but these conditions only widen the range of a given allotrope.They do not convert one slag type into another. The nature of the slag types and experiments with additives to convert one slag type into another are discussed.The various uses for allotropes of blast furnace slag are considered.Their use in air cooled slag, foamed slag, slag wool, cements, soil stabilization, glass bottles, and building bricks and blocks, is explored in some detail.INTRODUCTIONWithin recent memory, blast furnace practice has been solely concerned with the production of iron. The slag make at this time had not reached embarrassing proportions. In Britain, unlike Germany, no legislation existed to prevent the growth of unsightly slag banks. Generally slag found limited use as fill and road material in the immediate plant vicinity. This is broadly the case in Australia today. In Europe and America, where the slag make is of the order of several million tons annually, the room problem and the cost of dumping slag has stimulated commercial and scientific research on the disposal problem. Currently, most iron plants in Europe can profitably dispose of at least 95 per cent of their slag make.

Jan 1, 1964

By Al. Valero, A. Domínguez

This paper appraises the energy requirements for mineral production through an exergy approach taking into account the long-term decline in ore grades. In this context, the exergy required for restoring resources from the dispersed state of the so called Crepuscular Earth into the physical and chemical conditions in which it was delivered by the ecosystems in light of the available technology, is known as exergy cost. The exergy cost is the point of reference in order to evaluate in a single variable, characteristics such as composition, concentration (ore grade) and the state of technology. The ratio between the exergy cost and the minimum thermodynamic cost required to accomplish the same process is called unit exergy cost and provides a measure of the irreversibility of the analyzed processes. Otherwise, the ore grade is one of the main issues which affects directly the costs associated with mining the ore. Hence, the unit exergy costs to produce minerals from progressively lower ores grades by the current technology is analyzed. The unit exergy cost curves are presented for some important minerals such as aluminium, chromium, cobalt, copper, gold, lead, manganese, nickel and zinc, in order to know the trend when the ore grade decreases.

Jan 1, 2011

By Forrest T. Moyer

Injury experience in the mineral mining and processing industries during 1968 was slightly improved in the nonfatal-injury record but worse in the fatality record. The resulting frequency rate of all injuries was slightly better, whereas the injury-severity rate retrogressed appreciably from the figure for 1967. Overall operating activity, as measured by man-hours of worktime, was slightly higher in 1968. However, there were several major segments of the mineral industries in which activity was lower owing to reduced demand for mineral products and to several major work stoppages. These statistics comprise the injury and work experience of all personnel engaged in production, exploration, development, maintenance, repair, and force-account construction work, including supervisory and technical personnel, and working partners and owners at mineral-producing and mineral-processing establishments in the United States. Data concerning officeworkers are excluded except for the oil and gas industry for which such information is not separable. All injury rates and totals are calculated from data before rounding. The data for 1968 are preliminary except for the anthracite, coke, petroleum and natural gas, native asphalt, peat, and slag industries, which are final. The figures represent full coverage for all industries except oil and gas for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1970

By Frank Firmstone

It is proposed to consider here only comparisons made between results obtained when the materials employed are precisely the same, two furnaces at the same works for example, or the same furnace under different conditions as respects temperature of blast, method of charging, etc. With this limitation, the most important point in the comparison is the amount of fuel consumed per ton of iron. This, in fact, is the only item in the prime cost of the iron which can properly be said to vary in consequence of changes in the furnace process; for of the other principal items, the ore used per ton of iron, and also the amount of fluxing material, will depend on its richness, which, under the assumed conditions, will be practically invariable when taken over any considerable period; the labor cost also, from its nature, should be very nearly constant when estimated on the ton of iron. Moreover, as it consists principally in handling and moving material, it is greatly affected by circumstances quite independent of

By W. H. Langer

Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

Jan 1, 2009

In 2007, a total of 725 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Nonmetal mines com-prised 4.9% of all m ining operations. ? Mines producing common clay comprised 25.4% (n=184) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the U.S. Virgin Islands.

Aug 1, 2009

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size.IntroductionIron Oxide Copper Gold (IOCG) deposits are copper and gold ores hosted within a large body of iron oxide and are significant ore deposits for copper and gold (Williams, et al., 2005). These deposits can also contain economic levels of other metals such as uranium and rare earth elements. The known sizes of IOCG deposits range from 10 to 4,000 million tonnes with grade of 0.2-5% copper and 0.1-3 g/t gold. One of the greatest IOCG deposits is Olympic Dam in South Australia. It is the fourth largest copper deposit and the largest uranium deposit in the world. Gold and silver in the deposit also contribute significantly to the total revenue."

Jan 1, 2017

In 2004, data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 891 underground (6.2%) and 13,587 surface (93.8%) mining operations.

Sep 1, 2007

By T. P. Letsebe, L. Magwaza, T. A. Sethu, S. M. Rupprecht

"The authors were tasked with introducing safe and efficient drilling and blasting practices to a small artisanal mine located in the Eastern Province of Rwanda. The current mining methods employed at the mine are inefficient as rockbreaking is conducted utilizing hammer and chisel, or by drilling and blasting with no understanding of the rockbreaking process. The paper discusses the drill and blast cycle, as well as the associated activities necessary to support the mining cycle. The challenges and critical aspects in implementing drill and blast activities are discussed, as well as some of the technical aspects, i.e.drilling pattern, initiation and timing of the blast, and handling of misfires. Ancillary issues such as ventilation, training, communication, effective planning, logistics, and human relations are also examined. IntroductionRockbreaking accounts for 60% of the direct mining costs in small-scale mining. When drilling and blasting practices are poorly implemented the process becomes inefficient and dangerous. The introduction of a proven drill and blast system to artisanal mining offers a number of challenges, with safety being considered the backbone of any sustainable operation and a standard that cannot be compromised.The paper is based on a project at an artisanal cassiterite (tin) mining operation in a small village in the Kayonza District in the Eastern Province of Rwanda. A drill and blast programme utilizing industry best practice was introduced at an underground development end; a raise developed at an inclination of 23 degrees. The underground working is accessed via a 17 degree incline shaft with an operating length of 105 m and serviced by a single drum winder. The winder operates at a speed of about 3.5 m/min hoisting two 1 t wagons from the bottom of the incline to surface for tipping (Figure 1)."

Jan 1, 2017

W. S. GRESLEY, Erie, Pa. (communication to the Secretary): A six-entry method of opening coal-mines is, or was a short time ago, practiced in the Connellsville coal-region; but Dr. Chance's method has a novel aspect; for while in the Connellsville region the main pillars are formed outside of two pairs

Jan 1, 1901

By Harry R. Dahlberg

Heap leaching is discussed as a unit process. Five factors are identified as the principal elements that can be measured and/or controlled. These are: 1. Material Size 2. Volume of solution 3. Tonnage of heap 4. Time 5. Solution concentretion. The Rate of Extraction Curves obtained from an actual heap or column tests describes the economic viability of the unit process. By analysis of these curves and the five factors end their inter-relationship it is possible to determine how the extraction rate can be increased. The practice of leach and rest used by many operators is analyzed and shown on a hypothetical rate of extraction curve. The influence of the driving force of the hydrogen ion and ferric Lon as Lixivants and its effect on the rate of extraction curve is discussed.

Jan 1, 1979

By H. T. Sumsion, A. U. Seybolt

The results of an investigation of vanadium-rich V-O solid solutions are presented, indicating the structure and lattice parameters of two solutions, a and ß, and their approximate temperature-composition existence. The a solution is the terminal body-centered cubic one, and contains up to 3.2 atomic pct 0. The ß solution has an ordered body-centered tetragonal structure, is formed at 1270°C, and exists from about 15 to 22 atomic pct 0. From the evidence available, the various phase boundaries have no appreciable temperature dependence. Evidence has been found for a polymorphic transformation in pure vanadium at 1550°C. IN an earlier investigation' dealing with the preparation of pure vanadium by calcium reduction of the oxide, it was found that small amounts of oxygen drastically reduced the ductility of the metal. Because this effect was so marked, it was decided to make a study of the solubility of oxygen in solid vanadium. This report deals principally with this solubility and the nature of the phase relationships in the vanadium-rich region, particularly at temperatures below 1300 °C. However, during the investigation enough data on the V-0 system were obtained to make it appear worthwhile to present a tentative phase diagram up to the composition VO. The only significant prior work found on this system are the contributions of Klemm and Grimm,' and Mathewson et al.3 Klemm and Grimm prepared a wide range of V-O compositions by powder techniques including the compositions VO.l, VO.2, VO.3 and VO4 (9.1, 16.8, 23, and 28.6 atomic pct 0, respectively). The first three compositions were found to consist of a body-centered tetragonal solid solution, while the last also showed lines of VO (NaCl structure). They found that the parameter c, increased and the parameter a, decreased with increasing concentration of oxygen. For their composition VO.27, or about 16.8 atomic pct O, they cite the values a, = 2.948A, c, = 3.53A, and c/a = 1.2. Klemm and Grimm made no attempt to determine the solid solubility limit nor to construct a phase diagram. They did, however, give some data on the homogeneity range of VO, and they proposed a structure for the body-centered tetragonal solid solution; these points will be taken up later. Materials and Preparation of Samples The vanadium used in this investigation was prepared in the laboratory by the method previously mentioned.' A typical analysis is as follows: Fe, 0.007 pct; Si, 0.02; Ca, 0.06; C, 0.224; O2, 0.044; N,, 0.0017; H2, 0.003; and V, 99.34 ±0.3 (assay). The vanadium assay is probably low by about the error given. The impurities total about 0.36 which, if subtracted from 100, gives a purity of about 99.6. At the time material was being prepared for this work no suitable technique was available for melting vanadium without appreciable contamination. The procedure adopted therefore was to cut the calcium-reduced regulii into slices which were then rolled to strip about 0.025 in. thick for oxygen diffusion. Pieces of rolled vanadium of approximately 0.025xY4xl in. and weighing about 0.3 g were suspended in a vertical fused-silica tube which was part of an ordinary gas absorption apparatus. The silica tube was heated by an electric resistance-tube furnace which could be raised around the silica tube or lowered away from it as desired. This apparatus had no novel features which require detailed description. Other than the silica tube and furnace, it consisted of a glass system evacuated by a liquid nitrogen trapped mercury diffusion pump, a mercury-operated gas burette, a McLeod and a Pirani gage, and a mercury manometer. It was also equipped with suitably located stopcocks for isolating various parts of the system; the vacuum ordinarily attained was between 10" and 10-6 mm of mercury. Oxygen generated by decomposing MnO2 was passed through anhydrous magnesium perchlo-rate before introducing it into the gas burette and thence to the absorption chamber.

Jan 1, 1954

By David M. Abbott

This paper is a companion to, and amplification of, the ?History? section of the 2014 version of the SME Guide for Reporting Exploration Results, Mineral Resources, and Mineral Reserves (SME Guide). The need for the careful examination and evaluation of mineral deposits has long been recognized. In the book De Re Metallica, Georgius Agricola noted, ?Moreover, a prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him? (1556, p.29). Agricola further stated, ?Now a miner, before he begins to mine the veins, must consider seven things, namely: the situation, the conditions, the water, the roads, the climate, the right of ownership and the neighbors? (1556, p. 30). The elements of Agricola?s seven things, much expanded, are incorporated into the 2014 SME Guide. As reflected in this quotation, veins were the primary concern of mining until 20th century technology permitted bulk mining techniques. The need for standardization of reserve descriptions arose along with the development of western mining in the United States and the concurrent development of mining engineering and mining geology as professions. By the turn of the century, debate about terminology of various classes of reserves was in full swing. Herbert Hoover noted in 1909 (p. 16-17), ?The old terms ?ore in sight? and ?profit in sight? have been of late years subject to much malediction on the part of engineers because these expressions have been so badly abused by the charlatans of mining in attempts to cover the flights of their imaginations. A large part of Volume I of the Institution of Mining and Metallurgy has been devoted to heaping infamy on these terms, yet not only have they preserved their places in professional nomenclature, but nothing has been found to supersede them. ?Some general term is required in daily practice to cover the available field of visible ore, and if the phrase ?ore in sight? be defined, it will be easier to teach the layman its proper use than to abolish it. In fact, substitutes are becoming as badly abused as the originals ever were. All convincing expressions will be misused by somebody.? Hoover (1909) noted that the common terms at the time were: ? Positive ore or ore developed: Ore exposed on four sides in blocks of a prescribed size. ? Ore blocked out: Ore exposed on three sides within a reasonable distance of each other. ? Probable ore or ore developing: Ore exposed on two sides, ? Possible ore or ore expectant: Ore in whole or in part below or beyond the range of vision. Hoover stated that these, and similar terms, overlapped and had the difficulty of failing to account properly for geologic variation in metal distribution beyond the exposed face. Certainly assuming extension of values along a vein is reasonable, but how far? Also, these definitions are for vein deposits, not all types of deposits are in veins. Hoover (1909, p. 19), therefore, defined the following terms. ? Proved ore: Ore where there is practically no risk in failure of continuity. ? Probable ore: Ore where there is some risk, yet warrantable justification for assumption of continuity. ? Prospective ore: Ore that cannot be included in the above classes, nor definitely known or stated in any terms of tonnage.

Feb 1, 2014

By A. M. Gaudin, J. H. Brown

In a survey of the effects of heat treatment on the comminution of various rocks, it was found that unusual size distributions often characterize the broken products, and that this is related to a great increase in intergranular fracture1. It is the purpose of the present paper to contribute to an understanding of this effect. In a thesis by one of use, critical consideration was given to many mechanisms which could conceivably be responsible for the increased intergran-ular fracture. It was shown that neither gross chemical changes nor intergranular corrosion are required. Among non-chemical mechanisms the most likely appeared to be (1) Uneven expansion due to thermal gradients, giving spalling (2) In a manner similar to that prevailing in metals, the appearance at high temperature of intergranular weakness. (3) Unequal thermal expansion of adjacent grains. Experiments were designed and conducted to permit a choice among the many alternative mechanisms and in particular among the three listed here. EXPERIMENTAL MATERIALS Tests were made on the materials listed in Table 1. Of each material, only lumps similar in composition and grain size were used. The three marbles listed in Table 1 were analyzed to assure that their chemical compositions did not differ greatly (Table 2). On the basis of the chemical analyses, of differential thermal analyses, and of X-ray powder diffraction patterns, it appeared that the marbles were very similar except for their grain sizes.

Jan 1, 1961