Search Documents

By A. J. Forney

This report summarizes the findings of methods of treating caking coals in a fluid bed to destroy their caking properties. In batch tests it was found that several coals, including those with a free-swelling index greater than 8, could be decaed at temperatures from 400° to 425° C with a fluidizing gas composed of inert gas or steam containing 0.2 percent oxygen and a minimum residence LS,-;,' of 5 minutes. When treatment decreased the free-swelling index from about 8 to 1-1/2 or lower, the resulting treated coal was noncaking. In a continuous unit with continuous feed and discharge of coal, slightly more severe conditions were required to decake the coal. For 18- to 100-mesh coal a temperature of 430° to 440° C and an oxygen-to coal ratio of 0.4 cubic foot of oxygen per pound of coal feed was necessary. Finer mesh sizes required lower oxygen-to-coal ratios. In tests using air only as the fluidizing medium and treatment temperatures well below the softening range, the caking properties of 150- to 200-mesh coal were destroyed in 30 to 40 minutes of residence time at 200° C. Coarser sizes of 18 to 48, 48 to 100, and 100 to 150 mesh required longer residence time.

Jan 1, 1966

By E. M. J. Alenius

This paper describing the mining practices at the United Verde open-pit mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The purpose of this paper is to present the methods used in developing and operating the mine, and to discuss the problems encountered.

Jan 1, 1930

In this issue, the Bureau of Mines announces the availability of the latest of its Mineral Perspectives series: ?MP-4, mineral Industry of Western Europe." This publication describes the mineral industries of 19 Western European countries. For readers unfamiliar with this new series, reproduced below and on the two succeeding pages, is the section dealing with the mineral industries of France. Information regarding acquisition of this publication is found inside the back cover of this issue. FRANCE France is a moderately important producer of minerals, including iron ore, coal, potash, fluorspar, and uranium. In addition, France is a significant processor of imported minerals, chiefly for its own consumption. In general, it has exportable surpluses only of a little iron ore (low-grade ore exported to Luxembourg) and some nonmetallics.

Jan 1, 1977

By D. Harrington

In this period of generally increasing taxes of various kinds, one hears less complaint by mining companies about the high cost of workmen's accident compensation than was the case a few years ago, the reason perhaps being that other and more pressing phases of the tax problem now over shadow the heavy expenditures for compensation premiums which a few years ago were considered a severe burden on the mining industry. Nevertheless, the financial expenditures of the mining industry in higher compensation benefits and hospitalization or in higher premium rates, or both, instead of being less have actually increased in many States in the past year. In the spring of 1937, proposals for increased benefits to injured employees in compensation, hospitalization, or medical aid were actively before legislatures in California, Connecticut, Georgia, Idaho, Illinois, Indiana, Iowa, Kansas, Kentucky, Massachusetts, Michigan, Minnesota, New Mexico, Oregon, Pennsylvania, South Carolina, Texas, Utah, Washington, Wyoming, and possibly other States. In some cases, the proposed increases in benefits were so much greater than expenditures for similar items in the past that premium rates per $100 of payroll would almost certainly rise sharply. At this same time, occupational-disease-compensation coverage also was under consideration by legislatures in Arkansas, California, Delaware, Idaho, Indiana, Kansas, Massachusetts, Michigan, Minnesota, Montana, Nebraska, New Jersey, Ohio, Pennsylvania, Tennessee, Utah, and Washington. Sooner or later (and probably within the next few years) occupational-disease compensation will be accorded practically as wide recognition as accident compensation receives at present, and, unquestionably, mining in all of its branches will be affected more or less drastically. Hence, the present outlook is that the mining industry, in company with practically all other industrial activities, will be confronted by materially higher compensation costs than those of the past or the present, to which rather violent exception has been taken, at least in some States and at some times.

Jan 1, 1938

By Thomas Gales

Longwall mining has a high potential for producing bulk production from a single face. Production is interrupted for a considerable time when it is necessary to move the equipment to a new block of coal. The frequency of such moves can be reduced by increasing the dimension of the block to be moved. Merely doubling the tonnage in a block to be mined may increase production by more than 21,000 tons per year. The time taken to move the equipment can be reduced by careful preplanning, industrial engineering analysis, and specially designed equipment. Reducing its move time from 30 days to five days can increase production by more than 25,000 tons per year. Increasing the panel dimensions and reducing the move time can give an increase in pretax profits of more than $600,000. A comprehensive bibliography is included.

Jan 1, 1977

Workers at Anaconda Aluminum Company's primary aluminum smelter at Sebree, Ky., were back on the job December 1, after agreeing to a new 3-year contract. The old contract had expired November 15. On December 20, the Aluminum Company of America reportedly shut down a 42,000-ton-per-year potline at its Wenatchee, Wash., primary aluminum smelter and half of a 23,000-ton-per-year potline at its Vancouver, Wash., smelter as a result of a power cutback by the Bonneville Power Administration. A1 so in December, Kaiser Aluminum & Chemical Corp. reduced overall power at its Mead and Tacoma, Mash,, smelters and shut down one of eight 27,500-ton-per-year potlines at Mead. Reported shutdowns for the firms since September have amounted to 76,000 tons for Alcoa and 50,000 tons for Kaiser. Alcan Aluminum Ltd. announced plans to double the generating capacity at its Kemano hydroelectric power plant in British Columbia to 1,916 megawatts. The additional power would be equal to that required of a primary aluminum smelter with an annual capacity of 567,000 tons.

Jan 1, 1980

By Ho SE, Neil Phillips G, Houstoun SM

There are numerous individual gold deposits in the Archaean greenstone belts of Western Australia, but only 26 have productions and/or quoted reserves in excess of 10 tonnes Au. Most gold production has come from mineralization in shear zones, quartz veins or stockworks in volcanic or intrusive host rocks, particularly tholeiitic basalts or dolerites metamorphosed at sub-amphibolite facies (e.g. Kalgoorlie). Significant prod- uction has also come from BIF-hosted deposits (e.g. Hill 50), and large reserves are quoted for mafic hosts at high metamorphic grade (e.g. Big Bell). Most deposits have marked structural control, great depth extension, and are characterized by zoned alteration haloes of pyritization (with Au), K-metasomatism and carbonation. On the regional scale, most larger volcanic- or intrusive-hosted deposits occur in younger (ca 2.8 b.y.) rift-phase green- stones (Norseman-Wiluna Belt). These belts also have a high prospectivity (36 kg Au/km2 of greenstone belt). Younger (ca 3.0 b.y.) and older (ca 3.5 b.y.) platform-phase green stones of the Murchison and Sodthern Cross Provinces and the east Pilbara, respectively, are progressively less prospective (14 kg Au/km2 and 0.8 kg Au/km2, respectively) and also have progressively smaller deposits. The important regional- and local-scale characteristics of most gold deposits can be explained in terms of a metamorphic- replacement model. In this model, metamorphic H2O-CO2 fluids, focussed by faults and shear zones, infiltrated host rocks and deposit gold at 350 + 50¦C and 1-2 kb, largely in response to fluid-wallrock interaction. In many large deposits, gold precipitation was synchronous with sulphidation of Fe-rich host rocks, but the diversity and abundance of smaller deposits reflects the variety of reactions precipitating gold from ubiquitous, auriferous metamorphic fluids. Regional variations in abundance and size of deposits relate to factors such as tectonic setting, alteration styles and possibly source rocks.

Jan 1, 1986

The mechanism of thiosulfate decomposition and the products formed were investigated in the presence of pyrite or pyrrhotite in copper-ammonia solutions used for leaching gold. The presence of the sulfides significantly increased the decomposition of thiosulfate. The sulfide-surface-catalyzed oxidation of thiosulfate to tetrathionate by dissolved oxygen or the cupric tetra-ammine complex was proposed to be the dominant thiosulfate decomposition mechanism. The catalysis of the sulfides in this reaction could originate from their strong affinity for aqueous sulfur species and their semiconducting properties. Oxygen was found to be the initial driving force for thiosulfate decomposition in the absence of cupric ions and the driving force for the continuous decomposition of thiosulfate in the presence of cupric ions. Under an oxygen free atmosphere, the decomposition of thiosulfate was limited to reduce the cupric ions and the catalytic effect of the sulfides was also marginal. The dominant oxidative product of thiosulfate was trithionate in alkaline solutions especially in an oxygen rich or cupric ion rich environment. Tetrathionate was found in relatively smaller amounts in an oxygen and cupric ion deficient environment. Tetrathionate was not stable and would further decompose after extended periods. Trithionate concentrations increased almost linearly with time.

Jan 1, 2005

By T. Szendrei, S. Tose

The fracturing and movement of rock that occurs in the vicinity of a stemmed borehole charge in open pit mining operations are described by examining the effects of the emitted stress waves – shock and elastic – and the expansion of high-pressure detonation product gases. Three principal modes of momentum transfer to fractured rock are identified, all linked to gas expansion work. This work can be delivered radially (burden), axially (stemming), and in the collar zone (cratering). Flyrock is generated under unusual combinations of blast parameters and rock properties. Although infrequent and seldom predictable, the generation of flyrock can nonetheless be interpreted and modelled in terms of the principal mechanisms of rock projection described in this study. The physical processes underlying these principal mechanisms are identified and will permit the development of predictive models for flyrock velocities.

Dec 13, 2023

By Mark E. Gershon

Extensive efforts are under way to- ward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1985

By F. Ntuli, T. V. Nyangadzayi

Chromium green is an essential metal with various applications in the paints, construction, electronics, and aerospace industries. The main source of chromium green is the carbo-thermic reduction of chromite ores, however, chromite ores are being heavily depleted on a global scale, hence the need to find alternative or secondary sources for the chromium. In order to meet the global demand for chromium there is a need to implement principles of the sustainable circular economy to keep chromium within the material loop. Ferrochrome slag and stainless steel slags are secondary resources that are potential sources of chromium. In this work, recovery of chromium from ferrochrome slag was investigated. The ferrochrome slag was alkaline leached using sodium hydroxide- sodium hypochlorite solution to reduce the use of potent reagents that have a potential negative environmental impact. The leachate produced by oxidative alkaline leaching of ferrochrome slag contained hexavalent chromium, which was used to recover the extracted chromium through a two-stage process involving reduction and precipitation. Reduction of hexavalent Cr to trivalent Cr was investigated using anhydrous FeSO4 at concentrations of 5 g/L, 10 g/L, and 15 g/L. Precipitation was conducted by dosing the reduced leach solution with 1 M sodium hydroxide at dosages of 5 ml/L, 10 ml/L, and 15 ml/L. The experiments were designed using the Taguchi (L9) orthogonal array and analysed according to the ANOVA, general linear model. The optimized conditions for the reduction step were ferrous sulfate dosage of 5 g/L with a pH of 12, and for the precipitation step, 1 M sodium hydroxide at a dosage of 15 ml/L with a setting time of 90 minutes and pH of 7. Physical changes were observed during the two-step chromium recovery, with solution changing from a yellowish colour to dark green colour indicating completion of the reaction. The chromium recovery was found to be 93.3%.

Dec 11, 2024

By Stanley R. Riggs

The rocks exposed in the phosphate district are of Neogene age and consist of clayey quartz and phosphorite sands overlying phosphatic dolomite. The Bone Valley Formation is redefined as a marine phosphorite containing primary phosphorite and abundant terrigenous sediments. It contains a Middle Miocene vertebrate and invertebrate fauna and conformably overlies the Hawthorn Formation containing similar invertebrate fauna. A new, unnamed formation, with Pliocene and Pleistocene fauna and containing reworked phosphorite, overlies the Bone Valley disconformably. Its phosphorite is derived from the subjacent Bone Valley by post-Middle Miocene erosion and deposition in stream channels and marginal marine environments. The Bone Valley contains two main types of primary marine phosphorite. Orthocbemical phosphorite, a direct precipitate of microcrystalline phosphorite (microsphorite), occurs as a cement or binder in thin beds. Allochemical phosphorite consists of clastic phosphorite particles that were originally formed as microsphorite on another part of the shelf. Microsphorite was deposited in a very shallow open marine environment which had an abnormally high phosphorous content caused by upwelling currents. The mechanism of deposition is still in doubt, but organisms probably were a major factor. Soon after deposition, microsphorite was indurated, periodically torn up, and the resulting fragments transported and deposited elsewhere on the shelf. These processes account for a great portion of the clastic phosphorite in the Miocene deposits of Florida. The primary fossil skeletal material is of minor importance.

Jan 1, 1965

By G. H. Khoe

addressed in a number of studies in the past. In this paper, the stability of a ferrous arsenate compound is evaluated using a solution model and the thermodynamic data which were determined for the system. The environmental stability of the ferrous arsenate precipitate is compared with the literature data for ferric arsenate and arsenate-bearing ferric hydrous oxide.

Jan 1, 1991

By J. A. Roberson, A. M. Adair

A plate of an 18 pct Ni (250 grade) maraging steel was homogenized, cold rolled, and re crystallized to produce a fine grained, homogeneous structure. The strength properties were then measured as a function of cold rollinq prior to aging. Material in the solution heat treated condition exhibited substantial strengthening from cold rolling. The strength increase and the rate of strengthening were proportional to the amount of cold work. This benefit, of up to 50 ksi, was retained during aging for 3 hr at 900°F. The structures produced by cold rolling and aging have been systematically investigated by transmission electron microscopy. The dislocation debris produced by cold work influences the morphology and distribution of precipitate particles as well as the rate of precipitation. An essential feature of the high nickel maraging steels is a martensitic transformation from y to a with the resultant production of a supersaturated bcc solid solution. This solution decomposes to form precipitates during a subsequent aging treatment.' The martensitic transformation in low carbon Fe-Ni alloys and the mechanical properties of these alloys have been studied extensively.2"4 The carbon content of maraging steel is kept very low to avoid the embrittling Fe3C phase and to minimize the acicular, or twinned martensite common to high carbon steels. Maraging steels are usually strengthened only by heat treatment, but cold working is also quite effective in this respect as was shown by Decker, Eash, and Goldman,' Kula and Hickey,5 and the present work. There is, however, some disagreement between the present results and those of Kula and Hickey. Because of their unusual combination of strength and toughness, the maraging steels are suitable for applications where reliability at high stress levels is required. The strength level is achieved through a combination of solid solution hardening,' substructure hardening,3 and precipitation hardening,6 of which the last is the most important. The toughness of these steels has been reported to be a result of the absence of brittle grain boundary precipitates,7 and the fact that the matrix is a massive martensite rather than a twinned martensite.' One of the problems in the manufacture and use of maraging steel has been its tendency to develop laminations in sheets parallel to the rolling plane.9,10 The present investigation was intended to determine whether or not an improvement in the microstructure of this steel by thermomechani-cal processing would improve mechanical properties. I) EXPERIMENTAL PROCEDURES A plate ($ in. thick) of an 18 pct Ni-250 grade maraging steel* was obtained and examined metallo- "Analysis, wt pct: 18.1 Ni, 8.6 Co, 5.3 Mo, 0.4 Ti, 0.07 Mn, 0.05 Cr, 0.05 Si, 0.002B. 0.1 Cu. 0.05 Al. 0.002 Zr, 0.016 C, balance Fe. graphically. It was found to contain laminations as described by previous investigators. This plate was then annealed at 2100°F for 24 hr to promote homogeneity. Pilot studies on small coupons had shown that this was the minimum temperature required to accomplish homogenization in 24 hr. Since this treatment caused excessive grain growth, the steel was subsequently cold rolled and recrystallized. Cold rolling was accomplished at about 5 pct per pass to a total reduction of 66 pct. The standard solution annealing treatment (1 hr at 1500°F) was adequate to cause recrystallization of the cold worked steel. The recrystallized steel was then cold rolled and ground by various amounts to produce specimens with uniform thickness and selected amounts of cold rolling. All tensile specimens with less than 90 pct cold reduction were ground to a thickness of 0.050 in. Specimens with 90 pct cold reduction were 0.025 in. thick. All

Jan 1, 1970

By A J. Morrison, M Yahyaei, J S. Siong, J Wang, K Runge

The flotation cells used to upgrade ultrafine metallurgical coal (-250 µm) are usually poorly controlled leading to unnecessary loss of combustibles from the flotation system. This is mainly because coal flotation cells are typically controlled for process stability rather than optimisation of flotation performance. This is especially true for a flotation device commonly used in coal applications in Australia – the Jameson Cell. This then provides an opportunity to improve the flotation performance by shifting from a stabilising control strategy to a proactive optimising control strategy. For an optimising control strategy, the control system will require a means of relating and then measuring in real-time, the effect of changing operating conditions on the coal flotation performance. Hence, the major aim of this work is to propose a possible model-informed process control strategy that could be used for real-time performance optimisation. In this study, industrial site work was conducted on an industrial-scaled Jameson Cell at a Coal Handling and Preparation Plant (CHPP) in Central Queensland, Australia where superficial gas velocity was controlled to six different levels. At the same time, other process variables such as froth depth and flotation feed properties were measured. The empirical models developed from this study suggested that combustible recovery is a function of superficial gas velocity, froth depth, feed solid content and feed ash content and that a peak in combustible recovery existed as a function of superficial gas velocity. This led to the development of a model-informed control strategy that aimed to maximise the combustible recovery by determining and then operating the cell at the superficial gas velocity at which the peak occurs. This peak superficial gas velocity was found to be only a function of feed solid content. Based on these findings it would seem possible to operate a Jameson cell at peak performance by online measurement of feed solid content, prediction of the optimum superficial gas velocity and stabilising control to maintain operation at that superficial gas velocity set point. The development of this modelinformed control strategy can serve as a basis for the development of a more sophisticated modelpredictive control (MPC) system. However, more work will need to be done to improve the predictivity of the combustible recovery model by measuring and modelling performance over a wider range of operating conditions.

Aug 24, 2022

By I. S. Levy, J. L. Brimhall, B. Mastel

Specimens of' Hastelloy X-280, a low-cobalt version of the solid-solution- hardened nickel-base alloy Hastelloy X, were given a series of thermomechanical treatttzents. They were then Lensile-tested at room temperature and 1350°F. The Microstructures of the specimens tested at 1350°F were studied by electron Microscopy. Microscopy showed that dislocation tangling, caused by the cold working, mas still in evidence after aging-for 24 hr to temperatures as high as 1550oF. (Cr, Mo)23 C6, (Fe, Mo)6 C'. as well us an unidentifiable phase precipitale due to the combination of the thermomechanical treatments and subsequent tensile strain. The room -temperature and 1350°F tensile properties show a general increase ill strength and decreccse in ductility with increusing cold-work level. This is due to the dislocation taangling-. PerLurbatiot~s to this general trend occur- due to solid-solution weakening at the higher cold-work levels as a direct result of the preciplitation reactions. THE requirements for corrosion resistance and high-temperature strength place nickel-base alloys among the more promising materials for advanced nuclear reactor applications. However, when these alloys are irradiated at service temperatures, they generally suffer severe embrittlement'" and reduction in rupture life.3 Certain experimental treatments resulted in improvements in the tensile and stress-rupture properties of Hastelloy X-280, a solution-hardened nickel-base alloy.' To provide a basis for understanding these improvements, unirradiated tensile specimens were examined by electron microscopy. The results are reported in this paper. EXPERIMENTAL DETAILS Material. Hastelloy X-280, a low-cobalt version of Hastelloy X, is a member of the solution-hardened class of nickel-base alloys. The Hastelloy X-280 was obtained from 4- and 1-in: thick plates in the mill -annealed condition. Table I gives the chemical composition of the material as reported by the National Spectrographic Laboratories. ~x~erimental Treatments. Plates of suitable size, 12 by 3 by 1 in., or by + in., were cut under a water jet from the stock material and examined ultrasonic -ally for homogeneity of grain size and absence of voids. The acceptable plates were solution-treated at 2150°Ffor 1 hr and air-cooled. These plates were then reduced in thickness by cold rolling 0, 10, 15: or 20 pct along the original rolling direction. The plates were machined into buttonhead tensile specimens with a gage diameter of 0.125 in., with a gage length of 1.125 in., and with their tensile axes parallel to the rolling direction. The specimens were examined for quality of finish with a penetrant dye, ultra son ically checked for voids, and finally given a dimensional tolerance check with an optical comparator. The acceptable specimens were aged for 24 hr at either 1000" or 1500 F and air-cooled. These specimens were then held at 540°F in a water loop for approximately 18 days to qualify as controls for similar specimens irradiated under the same conditions of time, temperature, water chemistry, and flow rate. Table U summarizes the treatments. These treatments were investigated to establish whether prior precipitation and stabilization of carbide phases at strain sites within the matrix could reduce the amount of carbides available for precipitation at grain boundaries during service. Tensile-Test Conditions. Specimens were tested to fracture at room temperature or 1350 F in air on an Instron tensile-testing machine at a crosshead speed of 0.05 in. per min. The time for the furnace to reach equilibrium at 1350°F was approximately 30 min; soak time prior to testing was 15 min; and test duration was approximately 5 min.

Jan 1, 1968

By R. J. Sweigard

Three case studies were undertaken to investigate the role of land use potential evaluation in reclamation planning and to determine the impact of regional differences on the evaluation process. The three surface mines studied were representative of operations in the Appalachian, Interior, and Northern Great Plains provinces. The scope of the investigations included a survey of regional characteristics, a detailed investigation of the mining operations and site conditions, and an assessment of local land use planning activities in the area of the mine. Special attention was given to key factors that presently determine the use of reclaimed land. Also, for each case study, the postmining land use potential was evaluated using site planning principles. Specifically, the environmental, economic, and social impacts of several potential postmining land use plans were considered.

Jan 1, 1983

By D. P. McDonald

"IntroductionTHE PURPOSE of this paper is to present .a summary of the evidence given before the Petroleum and Natural Gas Conservation Board in support of applications to it for permits to export natural gas from Alberta.I will attempt to be objective in my statements, despite the fact that my main interest in the hearings before the Board was to advance the interests of my own clients, the Westcoast Transmission Company, Limited.The hearing of the export applications •commenced before the Board in January, 1950, with the .application of the Westcoast Transmission Company. Joint hearings were commenced in September, 1950, and completed on December 14th, 1951. The Board heard evidence in support of six applications for export, one application to build a gathering system in Alberta, and three interveners, the .latter being the City of Calgary, the local gas companies, .and the coal interests, including both operators of coal mines and the Unions.The evidence comprised better than 8,400 pages, over two million words, and occupied 92 days before the Board.The Interest in Natural GasThe natural gas industry is one of the newer industries. It is not yet twenty years •old. In the United States, the expansion •of pipeline facilities has been phenomenal in the last fifteen years, and particularly in the last three years, when a total of over two billion dollars was invested in pipeline facilities. There are approximately 250,000 miles of gas transmission pipelines in the United States at this time, with additional lines constantly being pressed."

Jan 1, 1952

By Zhao-cheng Liu

Iron oxide red pigment powders of high quality were synthesized from pyrite cinders. Iron ox-ide red pigment powders were synthesized by hydrothermal method from the precursor of Fe(OH)3 and Fe(OH)2 colloid, which were obtained after ammonia solution reacted with acidic leaching solution produced by the reaction of pyrite cinders with sulfuric acid. Effects of reaction concentration, reaction temperature, reaction time, pH value and n(Fe2+)/n(Fe3+) on main properties of oxide iron red were studied by experiments. The prepared particles were characterized by means of X-ray diffraction (XRD) and scanning electron microscope(SEM). The results revealed that the synthesized iron oxide red particles were _-Fe2O3 and pseudocubic with particle size of 0.50~0.75µm. Furthermore, the quality of iron oxide red pigment powders reached the first grade of national standard (GB1863-89 ).

Jan 1, 2009

By D. D. Hogarth

"Edward Haycock, Engineer and Public Contractor Edward Haycock was born in Shrewsbury, England, June 14, 1813. His father was John Haycock, a timber merchant and soap manufacturer, residing at Swan Hill Court, Shrewsbury, and his mother Esther was the daughter of William Hilton of Hempstead, Hertfordshire. Edward's paternal grandfather, John Hiram Haycock, was the first of a line of architects that ""changed the face of Shrewsbury"" and ""provided some of the best examples of typical Victorian architecture in Shropshire""(1). Nothing is known of Edward's early life or education, although it appears that he made no attempt to follow this artistic trend. In 1833, Edward immigrated to Canada. The following year, he married Mary Butler, daughter of Johnson Butler, a Lieutenant-Colonel in the Lincoln Militia during the War of 1812. Mrs. Haycock, as co-heiress of Johnson Butler's estate, was assigned 600 choice acres of farmland in Brooke Township near present-day Sarnia. This alone would have guaranteed a tidy income, but the Haycocks soon disposed of this land, the last lots being sold in May 1840. Instead, Haycock turned his hand to engineering and, for a number of years, was employed by the Great Western Railway first in Woodstock and later in Hamilton. He then moved to Port Hope, tried farming, worked in the engineering office of the Port Hope, Lindsay and Beaverton Railway Company, and later constructed a portion of this railway(2). During his stay in Port Hope, Haycock met his future partners Ralph Jones, a contractor, and Thomas Curtis Clarke, chief engineer with the P.H.L. and B. Railway Company. The alliance was styled Jones, Haycock and Company and their most successful venture was the construction of the Government Buildings in Ottawa. This work was the crowning achievement of Haycock's career and, no doubt, his proudest moment was at 11:30 a.m., April 2, 1860, when his daughter Mary Emily, then a little girl of 4, with a special silver trowel ceremoniously laid the first stone. Of special interest in this project were the quarrying operations, which introduced Haycock to the art and difficulties of mining as well as to the potential returns of mines. Sandstone, for facing, was drawn from four quarries, 10 to 12 miles from the Departmental Buildings. Haycock seems to have been in charge of these operations, which in the early stages involved an average labour force of 86 men and 43 teams. However, by 1861, quarrying had declined in importance and the contractors were able to concentrate whole-heartedly on the construction site."

Jan 1, 1999