Search Documents

By Cheng Wei

Fly-ash was used as adsorbent to remove butyl xanthate from aqueous solution in this study. Adsorption kinetics investigation reveals that the adsorption process abides by the Lagergren-second-order Kinetic Model, and fine fly-ash prepared by grinding has a higher second-order adsorption rate as 1.25 g/mg?min and a higher saturated adsorption amount as 10.92mg/g. Four influencing factors as adsorption temperature, solution pH, consumption of fly-ash and adsorption time were investigated. Testing results indicate that butyl xanthate removal rates declines slightly with the temperature increase within the range of 15-50?, increases slightly when pH rises from 7.27 to 8.01 and then declines from 99.65% to 98.25% when pH rises from 8.01 to 11.10. An enhancement of removal rates can be observed by increasing the consumption of the adsorbing agent or prolonging the adsorption time. Thermal desorption was adopted to regenerate the used fly-ash, and test results show that fly-ash possess good regeneration performance and could be used as adsorbent repeatedly with little influence on the adsorption capacity.

Sep 1, 2012

By H. C. Siebert

According to the "Survey of Energy Resources 1980" (1)*, which was prepared by the Federal Institute for Geosciences and Raw Materials in Hannover (FRG)for the World Energy Conference 1980 in Munich, the world coal deposits are assessed at 775 billion tce proven reserves 448 billion tce of them recoverable and 6 161 billion tce additional resources. If one ignores growth rates, the current world coal output of 2,8 billion tpy gives our recoverable reserves a static life expectancy of 175 years. With an average increase in world output of 3,2 % like between 1973 and 1980 this range would be further shortened to an alarming degree. Furthermore, the criteria used to distinguish between workable and unworkable resources give rise to the suspicion that deposit characteristics are not always taken into account to a sufficient degree. For example, little attention is paid to major ?Bonitaet" - factors such as dip and seam thickness. There have been wide-ranging scientific discussions on the lower limit for workable coal resources, but no such limits have been set at the other end of the scale. Otherwise it is well known that performance and costs are badly affected den in level and moderately inclined seams the seam thickness is more than 4 to 5 m, because special mining methods have to be used beyond this limit. These are associated with significantly higher costs than with the winning of seams of ?normal? thickness.

Jan 1, 1985

By J. B. Hiskey

The principle oxide minerals of molybdenum are wulfenite (PbMoO4), ferrimolybdite (Fe2(MOO 4)3.nH2O), powellite (CaMoO4), and ilsemannite (Mo304). Wulfenite is found in Arizona, New Mexico, Nevada, Utah, California, and Montana. It is also found in the states of Sonora and Chihuahua, Mexico. Prior to 1915 wulfenite ores were the primary source of molybdenum. The solubility of wulfenite in hot sodium sulfide was first noted by Bonardi(1) during attempts to sulfidize wulfenite material prior to flotation. He identified lead sulfide and soluble sodium molybdate as reaction products. Bacon (2) sulfidized wulfenite in preparation for flotation and by X-ray analysis found the reaction product to be lead sulfide. Holmes(3) made an extensive investigation of the extraction of molybdenum from wulfenite concentrates by leaching. Nearly 100% molybdenum extraction was possible from -100 mesh samples leached for 15 min with 10% sodium sulfide solution at room temperature. Molybdenum extraction from -100 mesh samples after leaching 30 min at a temperature of 45°C using 2, 4, and 6% sodium sulfide was about 32, 79, and 98% respectively. The extraction showed little sensitivity to time, temperature, or particle size using 10" sodium sulfide solution.

Jan 1, 1976

By Brij M. Moudgil

Flotation of fine and coarse coal after multistage addition of the frother was found to yield coal fractions with significantly lower ash content as compared to the feed. It was observed that the lowest ash content, specific gravity and reactivity of coal was associated with finer size fractions. Ignition and combustion characteristics of different coal fractions were evaluated using a differential thermal analyzer (DTA) with calorimeter attachment. It is suggested that in the ignition stage, the removal of mineral matter affects the reactivity through the physical changes brought about by the ash removal. In the char combustion stage the mineral matter seems to influence the reactivity through the catalytic activity of surface concentrations of metal ions, ratio of combustible/incombustible material, internal pore structure and roughness.

Jan 1, 1984

By George F. Kunz

Jan 1, 1902

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By S. C. Termes

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble crosslinked starch xanthate (ISX). ISX is insoluble, has a shelf life of over a year when kept cold, and has a higher molecular weight due to cross linking than the soluble noncrosslinked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines but not silicious gangue. Floc formation, floc size, and settling rate are strongly dependent on pH, with the pH dependence differing for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1982

By A. R. Sorta, D. C. Sego

ABSTRACT The settling, shear strength, and index properties of oil sands fines-sand mixture tailings (FSMT) for a wide range of solids and fines content are investigated. Results indicate that the liquid limit of FSMT obeys a linear mixture law. The fines-water ratio (FWR) governs the permeability of composite tailings (CT) and CT with comparable geotechnical behaviour can be produced from the same initial FWR mixtures. A phosphogypsum (PG) dosage > 900 mg/kg does not improve the dewatering behaviour of CT. The undrained shear strength of FSMT at the liquid limit is approximately 2.4 kPa, but is dependent on fines content at the plastic limit.

Jan 1, 2013

By W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphalerite and dolomite, has been used to experimentally validate the model for the case of dry, batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1986

By Masanori Abe, Yoshitaka Kitamoto, Kazuhiro Nishimura

"Ferrite plating is a chemical processing which utilizes Fe2+ - Fe3+ oxidation to synthesizing polycrystalline films of ferromagnetic spinels (MFe20 4, M = Fe, Co, Ni, Zn, Al, Cr, TI, etc:) directly from an aqueous solution at 24 - 100°C. This low temperature process allows us to fabricate new ferrite film devices on · substrates of such non-heat-resistant materials as plastics, GaAs integrated circuits, and biomaterials. Synthesized from an aqueous solution the ferrite plated ·films are highly biocompatible. Thus various magnetic device and biomedical applications have been proposed and realized using ferrite-plated films. Ferrite-encapsulated polymer microspheres are applied to antibody carries for enzyme immunoassay, and also to toners/carriers for photocopying. Perpendicular magnetic recording media utilizing plated CoNi ferrite films are proposed. The low-temperature synthesized films of NiZn and Co ferrites are potentially used as soft-magnetic and/or insulating layers, respectively at high/microwave frequencies.IntroductionFerrite plating is a processing which facilitates the formation of crystalline spinel ferrite films with various compositions, (Fe, M)30 4 (M = Fe, Co, Ni, Zn, Al, Cr, TI, etc.), directly from an aqueous solution at 60 - 100°C [1]. This opened the door to fabricating novel ferrite-film devices using substrates of such non-heat-resistant materials as plastics and GaAs integrated circuits [2-4]; conventional ferrite film preparation techniques such as sputtering, vacuum evaporation, MBE, LPE, etc., require high temperatures(> -600°C) for crystallization of ferrites, which deteriorates the non-heat-resistant substrates. Recently we extended ferrite plating to be preformed at room temperature [5, 6]. This enables us to use as substrates such organic materials as biomaterials (e.g. enzymes) having very low heat-resistance."

Jan 1, 2000

By N. Mungan

Laboratory imbibition and displacement experiments were performed using crude oil and cores drilled with water and preserved under anaerobic conditions. The purpose of these tests was to determine reservoir rock wettability and to find out if more oil could be recovered by use of NaOH solution than by conventional waterflooding. The preserved cores were found to be oil-wet. Contrary to work in the literature, these cores changed to water-wet upon contact with air. After exposure to air for a week, the cores yielded more oil by waterflooding than when preserved under exclusion of air. At reservoir temperature of 160F, flooding the preserved cores with 0.5N NaOH solution recovered more oil than an ordinary wa-terflood, and additional oil when following a waterflood. When the caustic solution was used from the beginning, all the extra oil was obtained before breakthrough; when the caustic followed a conventional waterflood, the extra oil was produced in the form of an oil bank ahead of the injected caustic. The increase in oil recovery resulted from wettability reversal. Also, use of caustic reduced the volume of injection required to flood out the cores. At room temperature, however, the caustic solution did not reverse the wettability and gave no additional oil recovery. Cores which had become water-wet by air exposure or caustic flooding were restored to their original oil-wet state when saturated with crude oil and allowed to equcilibrate at reservoir temperature for two weeks. Therefore, in the absence of preserved cores, it may be possible to restore weathered cores to their original wettability for use in laboratory floods. INTRODUCTION Waterflooding has been in use since 1865, and is by far the simplest of secondary recovery methods. Unfortunately, most waterfloods are inefficient in recovering oil, often leaving half or more of the original oil in place un-recovered. The low oil recovery generally results from low sweep efficiency and low displacement efficiency. Consequently, to increase oil recovery by waterflooding, sweep and displacement efficiencies should be improved. Sweep efficiency is primarily affected by reservoir heterogeneities and mobility ratio, while displacement efficiency is affected by the capillary forces between fluids and rock surfaces. For petroleum reservoirs, the capillary forces are expressed in terms of interfacial tension and wettability. If oil recovery is to be improved significantly in water- flooding, the capillary forces holding the oil in the raervoir porous matrix must be reduced or eliminated. One way to reduce capillary forces is to inject commercial surfactants ahead of the injection water into the reservoir. Laboratory tests of this method have shown no promise of an economical process yet, and no increase in oil recovery was obtained in the field trials which have been reported. Work is continuing in many companies to find surface-active agents which, in workable concentrations, can yield substantial added oil recovery. Another way to change capillary forces operating in petroleum reservoirs is by changing the pH of the injected water. Wagner et al.' showed that change in the pH sometimes activates the surface-active materials natural to some crudes and brings about gross wettability change. Since pH alteration can be obtained with cheap chemicals, such as hydrochloric acid or sodium hydroxide, the process shows promise of being economical in a field application. Pan American Oil Corp. reported oil recovery by use of caustic solution from a flooded-out reservoir.' Their test, conducted at a small additional cost, yielded results which were so sufficiently favorable and encouraging that the wettability reversal flood was expanded to portions of the field not previously flooded.13 It is important to bear in mind that changes in the pH of the water not only can reverse wettability but also can lower the interfacial tension between water and crude oil. Reisberg and Doscher4 have studied the pH dependency of the interfacial tension of Venture crude using sodium hydroxide solutions of various concentrations. Their data show that the interfacial tension was lowered from 23.0 to 0.02 dynes/cm by increasing the NaOH concentration from 0.005 to 0.5 per cent by weight. Thus, the use of NaOH may lead to additional oil recovery due to both wettability reversal and lowering of interfacial tension. Whether alteration of pH results in wettability reversal from oil-wet to water-wet and increases oil recovery depends on wetting properties of the reservoir rock and the crude. This necessitates delicate laboratory experiments, with suitable core and fluid samples from a field. Although many investigators have studied wettability reversal floods in the laboratory,1,2,5,6 these studies have been carried out with synthetic porous media, refined laboratory fluids and surface-active chemicals to simulate the process. The study presented in this paper is the first time that wettability reversal by pH alteration has been accomolished in laboratory core floods using carefully preserved natural cores, live crude and with experiments performed at reservoir pressure and temperature.

Jan 1, 1967

By Masanoub R. Fujioka

A brief discussion of the methodologies involved in dewatering practices, particularly as used in Hawaii in coralline formations. A description of early dewatering practices includes a number of case histories; later dewatering practices also are detailed with case histories. There were disasters and some successes. Grouting generally was not successful. Deep wells are technically feasible and generally the economical solution to deep basement construction.

Jan 1, 1986

By Alton B. Cook

Equipment has been designed and fabricated for study of the vaporization of oil during gas-cycling operations, A sand-packed steel tube, which can be rotated to minimize gravity drainage, is used as a model oil reservoir. A minute windowed cell at the discharge end of the tube through which the liquid-gas interface may be observed, makes possible the separate removal of produced free gas and gas-saturated oil. The operation of the model oil reservoir, and auxiliary equipment, are described by use of a schmatic flow diagram. Details of the specially designed equipment are illustrated by isometric and pictorial drawings, and a description of the experimental procedure is given.

Jan 1, 1959

By John Ward Smith

Dawsonite bearing oil shale of Colorado's Green River Formation offers a unique and vast (6.5 billion tons of Al2O3) resource of easily extractable alumina. The processing methods required by the thermal reactions dawsonite and its oil shale carrier also require production of shale oil, soda ash, and nahcolite as marketable coproducts. These production methods are presented. The alumina production process is contrasted with the Bayer process to describe technical advantages of extraction of alumina from oil shale which may offset the problems associated with processing a relatively lean ore. While alumina production from oil shale requires development of new technology, the technical problems appear solvable. Only the political problems arising from the now onerous and completely unnecessary Federal oil-shale withdrawal appear less solvable.

Jan 1, 1980

By T. Reed Scollon

Major interrelated factors to be considered in assessing the impact of air pollution control regulations on coal are: (I) the fuel and fuel-related limitations of such regulations; (2) the rate of adoption and areal scope of the regulations; and (3) the availability of fuels and fuel-burning equipment to meet the requirements. A growing number of regulations contain provisions limiting the emissions of sulfur oxides or the sulfur content of fuels or both. With few exceptions, these limitations have not yet become fully effective in those areas which have already adopted regulations, and pertinent details of future regulations or legislation for most other areas are unknown at this time. Sufficient information is not avail- able to determine the availability of low-sulfur fuels at various demand and price levels, and large-scale commercial feasibility of sulfur-oxides removal processes and equipment is believed to be some years away. Accordingly, with the many uncertainties and unknowns, it is possible at best to make only a rough assessment of the impact of such regulations or legislation on coal.

Jan 1, 1969

By Dominique Francois-Bongarcon

The world mining industry is facing a severe recession. Thus, it is time to recall the value of geostatistical methods which were formerly developed as a money-saving and productivity-increasing tool. The situation has worsened, but the techniques of geostatistics have dramatically changed. Up to millions of dollars can be saved during exploration with simple use of variograms; then, during reserves estimation with kriging methods; and finally, with the parameterization of reserves, when evaluating a project and optimizing its global mining parameters.

Jan 1, 1983

By M. Yoshida, S. Hanada, T. Takasugi

"A study has been conducted to examine the effect of ternary alloying elements on high temperature deformation of the C15 NbCr2 based intermetallics in Nb-Cr-X (X=V, Mo and W) alloy systems, which have attractive properties as high temperature structural materials. The high temperature deformation of the C15 NbCr2 intermetallics can be improved by two alloying methods. One method is based on geometrical consideration for site occupation and atomic size factor of component elements and additive elements in the single phase C15 lattice; addition of Mo and V can promote dislocation movement without introducing significant hardening. The other method is based on microstructural modification through ternary alloying; moderate addition of these elements results in a variety of duplex microstructure consisting of the C15 phase and bee solid solution without forming any intermediate phases, and can enhance the high temperature deformability. Particularly, alloys with duplex microstructure equilibrating with Cr-rich bee solid solution is shown to exhibit superior deform ability. Also, lattice property of the additive atoms in the C15 structure and phase relation between the C15 structure and the bee solid solution are investigated by OM, XRD, TEM and ALCHEMI observations and then discussed in association with observed mechanical behavior.IntroductionLaves intermetallics with AB2 stoichiometry belong to the largest group in a large number of intermetallics with various kind of crystal structures, and have a variation of the cubic CIS, the hexagonal C14 and the dihexagonal C36 structures, depending on stacking sequence of XYZ type, each of which consists of four interpenetrating atomic layers (1-3). Some of the Laves intermetallics have good functional properties and therefore are considered to be used as, for instance, magnetic materials, magneto-optical materials, hydrogen storage materials and superconducting materials (2). Also, the Laves intermetallics are considered to be good candidate as high temperature structural materials operating at high temperatures and in severe environment because they have high melting point, low density, and potential resistance to corrosion and oxidation. However, the Laves intermetallics are very brittle at low temperatures because they consist of complex crystal structures similar to many other intermetallics."

Jan 1, 1996

By H. R. Green, D. M. Lamb, A. D. Taylor

The design of slurry launders has usually been based on strictly empirical concepts. An examination of the most common procedures reveals that they do not account for many of the variables that are recognized as significant for slurry transport. These may include flow rate, volume concentration of solids, solids specific gravity, solids size distribution, particle shape, launder geometry, and roughness of the wetted surface. It was decided to develop a design procedure, which would accomplish two things: First: Take into consideration most of the known significant variables and systematize the procedure to assure consistent results. Second: Provide a rational basis for examining and utilizing operating data to refine and improve the system. To accomplish this, it was necessary to develop a basic design concept. This concept has been developed through a complex development history, and yet still appears workable and technically sound. That concept may be outlined as follows: First: The solids transport velocity is the fundamental basis for slurry launder design. Second: The stream configuration, hence the launder size, is integrated with the solids transport velocity so that the actual stream velocity exceeds the solids transport velocity. Third: The launder slope is that which will achieve the

Jan 1, 1979

By Miaoyong Zhu, Sen Luo

"A two-dimensional CAFD model was developed for simulating the solute diffusion-controlled dentritic growth in the low Peclet number regime. Mass conservation and local equilibrium at the solid/liquid interface were solved to determine the growth velocity of interface with consideration of constitutional and curvature undercooling. The modified decentered square growth proposed by Wang et al was adopted to capture the first eight neighboring cells. The comparison between the classic Lipton-Glicksman-Kurz (LGK) analytical model for steady state tip variables and the simulated values showed that the present model was capable of quantitatively determining the dendritic growth, and the simulation tests demonstrated that the effects of the mesh anisotropy in growth kinetics and crystallographic orientation were eliminated. The numerical simulations were performed to the dendritic growth ofFe-0.6%C binary alloy in undercooled melt, and the results showed that the present model could predict the dendrite morphology with artificial growth orientation in acceptable level.IntroductionDuring the solidification of metals and alloys, the dendrite grows from the substance or the undercooling melt and solute redistributes between the dendrite and the interdendritic liquid. The solidification microstructure is close related to the phase and solute evenness and has a close linkage with the properties of final production.In the past few decades, various kinds of deterministic and stochastic models have been developed to predict the evolution of microstructures in solidification, with the fast development of computer power. Among these methods, Phase Field (PF) model [1, 2] has been known as one of the most adequate deterministic models for directly simulating the dendritic growth. However, there is a vital drawback that the PF method requires considerable computation time and is limited to simulate very small domains with a few dendrites [3]. On the other hand, stochastic models, such as Monte Carlo (MC) method [4, 5] and Cellular Automaton (CA) method [6-8], have been usually applied to predict the solidification microstructure evolution. Comparing with the MC method, the dendritic growth kinetics is explicitly integrated in the CA model, while the MC model doesn't. Therefore, the CA method is more reasonable to predict the dendritic growth during the solidification of melt."

Jan 1, 2013

By Heinz W. Duddeck, Hans-Konstantin Nipp

The design of storage space or deep mining in rock salt should take into account not only time dependency of the rock salt behavior but also temperature effects. For deep mining of potassium salt the natural increase of temperature with depth may no longer be negligible. For the storage of cryogenic liquid gas in salt caverns more knowledge is nezded about the propagation of deep temperatures and their effects on the stress-strain-creep behavior of the surrounding salt. High temperature problems arise for nuclear waste storages in caverns or drill holes emitting radiation. A numerical model is proposed for the analysis of displacements and stresses including their time and temperature induced change. For the material behavior of salt constitutive equations are chosen composed of a combination of Hooke-Kelvin-Bingham-Newton-model based on experimental results (excluding at present deep cooling), Langer 1980. The parameters involved are depending on the stress level and the temperature. The finite-element-method is applied to rotationally symmetrical three-dimensional problems. The non-linear calculation method is based on an implicit method with respect to time. A modified Newton-Raphson-method and the initial strain approach are employed. Along with some experiences on suitable numerical procedures, examples are shown for the characteristical effects of time-temperature dependency. Having achieved convergency and reliability a method is now available for practical design and parametric sensibility studies.

Jan 1, 1982