Search Documents

The increasing transportation of solids by pipeline, in South Africa and internationally, replacing the conventional transportation methods of rail, road, and conveyors, has resulted in much research into this area of solids transportation. Pipeline wear continues to be an area of specific concern, since it constitutes a major cost during the life of a pipeline installation. Wear data from an accelerated wear test and actual pipeline tests are presented. Trends in the performance of the pipeline materials tested are discussed, and possible solutions to the problem of pipeline wear are presented.

Jan 1, 1992

By Richard V. Wyman

Leaching of a granitic rock mass by slightly acid groundwater brings uranium and genetically related ions into solution in groundwater. Uranium and related ions are moved through the vadose zone by groundwater which in turn moves through zones of greatest transmissivity into a deep zone of increased hydrostatic pressure. Cyclic wetting causes the hydrostatic condition to fluctuate causing recycling described by Gruner (op cit). Multiple cycling flushes the uranium ions from rock being leached and moves it via this method to permeable beds-channels-in the deep zone.

Jan 1, 1970

By S. K. Bose, P. K. Sahoo, S. C. Sircar, P. K. Jena

High grade manganese ores are utilized in metallurgical, chemical, and battery industries, whereas the low grade ores are not accepted for these purposes and hence get accumulated at the minehead. In the present study an attempt was made to solubilize the manganese value as its sulfate by roasting the low grade ore with a suitable sulfatizing agent followed by water leaching. The different parameters were determined in the laboratory scale. Based on these, kilogram scale experiments were conducted where an appreciable amount of manganese goes into solution during leaching.

Jan 1, 1981

By M. Dubrovsky, J. W. Evans

A laboratory scale cell (approximately 50 amps current) equipped with a fluidized bed cathode was used in a study of the electrodeposition of cobalt from acidified aqueous sulfate solutions The effect of current density (in the range 0.1 to 1 amp/cm2 of diaphragm), cobalt concentration (4 8 to 100 glliter) and catholyte pH (1 35 to 6 2) on current efficiency and energy consumption were determined. Generally the current efficiency increased with increasing current density and cobalt concentration Current efficiencies were comparable to those reported in the literature for conventional electrowinning

Jan 1, 1981

By Luis Dr. Sobral

In this study, the removal of zinc, cadmium and copper from an aqueous sulphate solution, derived from the biomass desorption process, was examined by using a reaction system with a three-dimensional high surface area electrode (RNiF). This reaction system was found to be extremely effective in reducing metal concentrations to the ppb range. The effect of cathode potential and flow rate were studied for three different nickel foam porosities. In addition, current- potential curves were recorded, at a rotating vitreous carbon electrode, to deter- mine the possibility of depositing the aforementioned metals separately.

Jan 1, 1998

By Gibbons S. L, Ritchie I. M, Murr D. M

Fundamental studies on the transformations of iron oxides have been carried out and related to the solution conditions in the Becher process. The results show that a number of iron oxide interconversion reactions occur in the aeration reactor with the products depending on the pH, temperature and oxidation potential of the aeration liquor. It is concluded that the lack of process control in the aeration reactor of the Becher process significantly hinders the ability to predict and produce high quality single phase iron oxides of a consistent colour.

Jan 1, 1990

By Frederick N. Rhines, Robert F. Mehl

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ‡ in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Zedele and of Zedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Kevin Clermont, William N. Kelley, William E. Bonini, John H. Vreeland

Gravitational field anomalies have been observed over many igneous intrusives of medium (4000 sq km) to small (100 sq km) size in outcrop area. These studies give good results because the residual anomalies can be separated from larger-scale crustal anomalies and density contrasts usually are present. Although unique solutions are not possible, the analysis of the gravity anomalies place important limits on both the areal and depth extent of the intrusive bodies. Of all possible geophysical techniques, gravity studies offer the most promise in the determination of the shape in depth of intrusive bodies.

Jan 1, 1972

By Martin Bolesta

The use of strata injection as a means of stabilizing brittle and heavily stressed ground as well as faulted zones is now state-of-the art technology. Users are obliged to select the right combination from a wide range of injection products and equipment in order to ensure that the operation will be a success. Laboratory tests and a fundamental understanding of the technical aspects of injection products not only help in drawing up the correct injection procedure but have in fact become indispensable for planning the most reliable and cost-effective solution.

Jan 1, 2001

By P H. Ferreira

The mechanisation of mine development is becoming increasingly important in our South African and Southern African mines with increased emphasis on safe and efficient mining. Raise, blind and shaft boring offer mechanised solutions for excavations such as:- [reef raises stope boxholes and shaft ore passes ventilation passes and shafts chairlifts large vertical hoisting shafts (in excess of 1200 metres in depth) angled hoisting shafts (from small to large diameter bored holes)] These techniques will be discussed with reference to relevant applications and the author?s comparison between conventional drill and blast techniques.

Jan 1, 2005

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper to discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: I—gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2—liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3—glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4—crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that car- ried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.' At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1—aqueous solution, a much more expansible liquid, and a gas; 2—aqueous solution, salt crystals, and a gas; and 3—the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20" and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.'-" Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.' , Hartley (1876, 1877),".'" Hawes (1881)," Wright (1881),'V ohnsen (1920),I3 and Holden (1925)"

Jan 1, 1953

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper to discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: I—gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2—liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3—glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4—crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that car- ried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.' At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1—aqueous solution, a much more expansible liquid, and a gas; 2—aqueous solution, salt crystals, and a gas; and 3—the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20" and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.'-" Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.' , Hartley (1876, 1877),".'" Hawes (1881)," Wright (1881),'V ohnsen (1920),I3 and Holden (1925)"

Jan 1, 1953

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper .to, discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in. brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: 1-gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2-liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3-glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4-crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that carried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant, contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.1 At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1-aqueous solution, a much more expansible liquid, and a gas; 2-aqueous solution, salt crystals, and a gas; and 3-the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20° and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.2-6 Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid. carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.7,8 Hartley (1876, 1877),9,10 Hawes (1881),11 Wright (1881),12 Johnsen (1920),13 and Holden (1925)14

Jan 1, 1952

By Robin P. Gardner

Prior work by the author has established that closedform analytic solutions can be obtained for certain steady-state and transient types of operation of open circuit, continuous ball mills. This is possible when the tanks-in-series concept is used with the segregated flow or lumped parameter milling models. Such models should be useful (whenever they apply) in any calculational application since they are efficient and simple to program for digital computation. For example, they might be used within a computer program such as that developed by Herbst et al. for the calculation of model

Jan 1, 1975

By T. F. Anstett

The Bureau of Mines estimated the potential availability of tungsten from 57 mines and deposits in 19 market economy countries. The tungsten resources of China and the U.S.S.R. were also estimated. This resulted from an evaluation of tonnage-cost relationships indicating the quantity of tungsten available as ammonium paratungstate (APT), artificial and natural scheelite, and ferrotungsten at various average total costs of production including 0- and 15-pct rates of return on invested capital. The evaluated deposits contain 1.2 million metric tons (t) of recoverable WO3, of which approximately 52,000 t of AEYT can be produced at the January 1983 market price of $5.37/lb, 89,000 t of natural and artificial scheelite at a market price of $3.63/lb, and 1,700 t of ferrotungsten at $5.61/lb of tungsten. An annual availability analysis indicates that by the early 1990's new deposit discoveries, development of known prospects, or expansions of producing mines will be necessary to meet projected tungsten demand.

Jan 1, 1985

By Rachel De Lucas

Current methods of hydrogen storage are an impediment to the transition of our energy infrastructure from a hydrocarbon to a hydrogen base. The transportation, handling, and storage costs of hydrogen gas account for a majority of its selling price. Magnesium hydride slurry is a safe, environmentally friendly alternative for hydrogen storage. If this form of storage is to be adopted on a large scale, a cost-effective method for recycling the enormous amounts of magnesium hydroxide byproduct must be identified. The solid oxide membrane (SOM) process can be used to recycle the magnesium hydroxide byproduct into magnesium metal, which can be reformed into magnesium hydride and reused for fuel storage. Conventional magnesium extraction/recycling technologies require a great deal of energy and create byproducts that are harmful to the environment and human health. The SOM process poses none of these detrimental effects and requires less energy and feed preparation. The economic viability of a facility that utilizes the solid oxide membrane process for the direct reduction of magnesium must be examined in more detail if industry is to consider it. Cost analysis data related to the commercial viability of a scale-up will be compared to two standard industrial processes: current magnesium production techniques including electrolytic and metallo-thermic processes. We have shown in our cost comparison that the SOM process is cheaper than these traditional techniques and that it is also comparable to aluminum's Hall-Héroult process in cost but with none of the environmentally harmful byproducts.

Jan 1, 2006

Mineral resource classification is essential because it is required for public disclosure. The resources must be binned by a qualified person into measured, indicated and inferred categories using an appropriate methodology. The classification methodologies used have long been a topic of research and discussion. There are various traditional and geostatistical methods used in practice. Some are more popular than others. Because of the uniqueness of each ore deposit, it seems almost impossible to have a single industry-accepted norm for mineral resource classification. Therefore, some experts have adapted the methodologies tailored for the deposits they are working on, but many simply use the methods they and their clients understand and are comfortable with. In this paper, a new approach is presented to classify the mineral resources using a data geometry index. This index combines both traditional and geostatistical aspects of resource classification based on the data configuration around the block interpolated. It is a function of several variables such as kriging variance calculated for a block, distance from the block to the nearest sample and the average distance of all samples used to interpolate the block. Thus the approach using this index takes into account the spatial data configuration around the block being estimated, as well as the traditional distance criteria. The data geometry index and how it is calculated is explained. A case study for a gold deposit is presented to see how the classification based on this index compares to the existing methodology used in this deposit for mineral resource classification.

Sep 26, 2011

By W. W. Loo

A REVIEW of the literature on the reduction of cassiterite showed. that scarcely any progressive changes were made in the methods of reducing cassiterite until within the last two decades, and that during that period many improvements in the metallurgy of tin have taken place. Since 1914 the world's consumption of tin has increased considerably, resulting in the exploitation of primary tin deposits such as the Bolivian lode, which has become an important source of tin. On account of the low tin content of Bolivian ore, and the presence of objectionable impurities of the reduced tin, the smelting of this ore and the refining of the tin has changed considerably from the methods formerly used. A comparative study of the methods of smelting cassiterite concentrates suggested that an investigation be planned so as. to determine what factors effect the extraction of tin from its ores by reduction with carbon. The first part of the experimental work was the determination of whether roasted cassiterite concentrates can be reduced by carbon without the use of flux, and the reduced pellets of tin be collected into a single mass separate from the dry gangue residue The second part of the experimental work was a comparison of the effect of variations of the different factors on the smelting of roasted cassiterite concentrates: first, the effect of varying the composition of the slag; second, the effect of varying the amount of reducing agent; third, the effect of varying the relative amount of the resulting slag; and fourth, the effect of different kinds of reducing agents:

Jan 1, 1928

By Frank Corwin

It is the purpose of this article to give a brief account. of the experimental work and to show how the increase in efficiency was brought about. Part of the experimental work described in this paper was carried out by the writers, while in the employ of the Anaconda Copper Mining Co., under the direction of M. W. Krejci, Metallurgist, and Arthur Crowfoot, Chief Sampler. Complete records of all of the MacDougall testing work have been placed at our disposal through the courtesy of A. E. Wheeler, Superintendent. II. BRIEF HISTORY OF PRESENT MACDOUGALL PLANT. The first change from the Brueckner cylinders used for roasting concentrates at Great Falls was the construction of a MacDougall roaster of the Herreshoff type. This furnace was first started on June 15, 1898. It bad eight hearths, was lined with fire brick, and had an air-cooled central shaft, but no provision was made for cooling the rabble arms. It was operated for a while, and accomplished the work of roasting, but ran so hot that the rabble arms became twisted and distorted out of shape. To prevent the furnace from becoming too hot a device was then installed to draw the heated gases away from the hearths. This consisted of a pipe connected to alternate hearths of the MacDougall furnace and also connected to the flue. It was equipped with dampers, 'so that the hot gases could be drawn away from any one of the alternate hearths directly into the flue.

Jan 7, 1913

By Herbert Herman, M. E. Fine

THE first decomposition product of a supersaturated aluminum-rich A1-Ag alloy at low tempera- tures is Guinier-Preston zones.'-, The zones are ideal and each consists of a spherical shaped silver-rich cluster about 16 A in diam syrounded by a silver-poor shell approximately 72A in diam.' The composition of the two regions is not known with certainty., After quenching from the solution anneal, these zones form rapidly on aging at temperatures as low as -30°C.5 The rate of zone formation increases with aging temperature; the activation

Jan 1, 1961