Search Documents

By W. T. Lankford, Edward Saibel

During the course of an investigation of the plastic flow of aluminum aircraft sheet under combined loads, several problems arose in which analyses of the conditions leading to unstable plastic flow were needed. In order to provide these analyses, and in the hope of attaining a better understanding of the general problem of unstable plastic flow, the present study was undertaken. It is well known that unstable plastic flow is associated with a form of mechanical instabi!ity frequently observed during the plastic deformation of ductile metals. This instability is characterized by the fact that, at its onset, plastic straining mill proceed at a constant magnitude of the externally applied forces. It is further typical that the resulting unstable flow is generally accompanied by the formation of a neck, a local bulging, or some other form of heterogcneous deformation. Perhaps the most familiar example of unstable plastic flow to the metallurgist is the formation of the neck in the ordinary tension test. It is well known that in this test most metals exhibit a maximum in the externally applied load, followed by the process commonly referred to as "necking down." Instability in the simple tension test has been frequently discussed and numerous investigators1'2'3'12 have derived the criterion for instability in terms of a critical rate of strain hardening. It is the purpose of the present study to extend the criterion for unstable flow to the more general case where the body undergoing flow is subjected to combined loads. It is hoped that the problems considered will provide a more consistent picture of the general features of this important form of mechanical instability. The most practical implications of instability in plastic flow arise in connection with sheet metal forming operations. In the formation of a great many sheet metal parts, the deformations are produced primarily by stretching. If the conditions which lead to unstable flow are fulfilled in such a formation, and if the resultant instability leads to a pronounced localization of flow, then the useful limit of ductility of the material will have been reached. It i; also essential that the effects of instability be taken into consideration in any study of the plastic flow and rupture of metals under combined stresses. In general, when unstable plastic flow is initiated, straining becomes localized, the geometry of the test splecimen changes, and the state of stress in that portion of the specimen undergoing plastic flow is no longer under external control. In many past studies of the effects of combinetl Metals On flow and rupture) account has not been taken of the fact that, although a given test may be started under constant

Jan 1, 1947

By Edward Saibel, W. T. Lankford

During the course of an investigation of the plastic flow of aluminum aircraft sheet under combined loads, several problems arose in which analyses of the conditions leading to unstable plastic flow were needed. In order to provide these analyses, and in the hope of attaining a better understanding of the general problem of unstable plastic flow, the present study was undertaken. It is well known that unstable plastic flow is associated with a form of mechanical instabi!ity frequently observed during the plastic deformation of ductile metals. This instability is characterized by the fact that, at its onset, plastic straining mill proceed at a constant magnitude of the externally applied forces. It is further typical that the resulting unstable flow is generally accompanied by the formation of a neck, a local bulging, or some other form of heterogcneous deformation. Perhaps the most familiar example of unstable plastic flow to the metallurgist is the formation of the neck in the ordinary tension test. It is well known that in this test most metals exhibit a maximum in the externally applied load, followed by the process commonly referred to as "necking down." Instability in the simple tension test has been frequently discussed and numerous investigators1'2'3'12 have derived the criterion for instability in terms of a critical rate of strain hardening. It is the purpose of the present study to extend the criterion for unstable flow to the more general case where the body undergoing flow is subjected to combined loads. It is hoped that the problems considered will provide a more consistent picture of the general features of this important form of mechanical instability. The most practical implications of instability in plastic flow arise in connection with sheet metal forming operations. In the formation of a great many sheet metal parts, the deformations are produced primarily by stretching. If the conditions which lead to unstable flow are fulfilled in such a formation, and if the resultant instability leads to a pronounced localization of flow, then the useful limit of ductility of the material will have been reached. It i; also essential that the effects of instability be taken into consideration in any study of the plastic flow and rupture of metals under combined stresses. In general, when unstable plastic flow is initiated, straining becomes localized, the geometry of the test splecimen changes, and the state of stress in that portion of the specimen undergoing plastic flow is no longer under external control. In many past studies of the effects of combinetl Metals On flow and rupture) account has not been taken of the fact that, although a given test may be started under constant

Jan 1, 1947

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003

By J. Nielen van der Merwe

The main objective of the research described in the paper was to determine the causes of falls of roof in South African coal mines. The south African Colliery Manager's Association and the members of the South African National Institute of Rock Engineering (SANIRE) who are employed by coal mines lent full support to the work. Fifteen major roof falls were investigated in detail and their causes established. This data was supplemented by mapping a large number of roof falls on four coal mines in less detail. The total number of recorded roof falls was 182. The data bank simulated the data bank of roof falls that resulted in fatalities in terms of the total number of falls recorded and the thickness distribution of the collapses. It was found that the causes of the falls differed for different thickness ranges of roof falls, The thin falls, classified as "Skin falls", which accounted for approximately 70% of all fatalities, were predominantly caused by ineffective joint support and excessive bolt spacing. Ineffective joint support was found to be a dominant cause of roof falls for all thickness ranges, while the influence of excessive bolt spacing diminished with increasing fall thickness. However, it remained a significant cause of roof falls even for the major falls. Burnt coal, dykes, bad mining practice, weathering and inferior materials were found to be minor causes, but nonetheless contributed to the falls. Horizontal stress was a minor cause, with increasing contribution for thicker falls. It was also found that the indicators of horizontal stress coincided with areas of reduced roof rock strength. In general, roof falls occurred in areas where the roof rock was found to be less competent in terms of rock mass rating systems. It was concluded that the Coal Mine Roof Rating (CMRR) system developed by NIOSH in the USA held promise for application in South Africa and should be investigated further.

Jan 1, 2001

By V. Korobko, M. Byantogtokh, N. Byambadorzh, V. Bysov

A three-stage operative planning of mining operations in ore opencasts is considered. The hierarchy of monthly-weekly, weekly-daily, daily-shift planning is offered. For the fastest elimination and deviations in problematic situations a level is analysed and weekly-daily or monthly-weekly operative plans are being constantly updated. Operative planning is formulated on information received of preparation and working of mining panels. The electronic maps of these panels are considered for automated operative planning. On the data of the registration of blasthole drillings on a panel, the position of blasthole entry, their depth and the number of a line are determined. The geologist specifies boundaries of ore grades by the bored silt. The qualitative characteristics of ores are determined by the chemical analysis of slime or magnetic logging of blastholes. The missing geologic information is obtained by interpolation on the data of detailed and operational explorations. During working of the mining panel the technologists mark the movement of shovels, associating this movement to blastholes. For this purpose technological attributes are used: when was the blasthole drilled, what drill-rig participated in drilling, what shovel was used and when was it worked? Around each blasthole the zone of its influence is built up. It represents a discrete, elementary volume of ore or waste. The discrete form of the data is most convenient, as it allows step-by-step methods to be employed of the scheduled tasks in many and various combinations. The account panel working technology avoids ‘combination’ explosions. The elementary blocks should be placed in a trajectory of shovel movement and the trajectory can not be arbitrary. It’s determined by the technological rules of extracting and loading of mine mass. In linking to blastholes, the trajectory of shovels is simulated by the sum of step-by-step moving from one elementary block to another. For this purpose a geometrical linkage of blastholes is used. At a railway haulage, or complete mining with truck haulage, the trajectory of movement is a shuttle along the front of operations in the panel. At a selective mining of ores the number of possible directions is limited to three: moving of a shovel by idle running along the front of operations in the panel, frontal pull all the way down of the panel, and withdrawal. The technologically acceptable trajectories of shovel movement are stored for the following estimation and selection of the best. The estimation is carried out on mathematical models with criteria on the method of the least squares of deviations based on preset parameters from the plan, uniform loading of shovels, and mixing of ore at unloading points. The equations of balance type and directive parameters of the plan, as well as technological restrictions of solid and of elementary blocks within the limits of a trajectory are the restrictions of the model. Depending on an industrial situation it is possible to choose one of the predetermined models. The presented technique is used for longitudinal shovel bench at the Erdenet ore-dressing company.

Jan 1, 2003

By Morris Muskat

A general theory has been developed for the effect of permeability stratification on the efficiency of the gas-injection phase of cycling operations. It has been applied to three special types of permeability variation; namely, exponential, probability, and linear. In the case of the exponential permeability distribution the effect of areal pattern sweep efficiency was also taken into account. The exponential permeability distribution can be characterized by the ratio of the maximum to minimum permeability, which has been termed the stratification constant. Curves were calculated for the variation in total wet gas recovery and total gas throughflow, to give that recovery to various abandonment limits of the wet gas content in the produced gas, as a function of the stratification constant. The cumulative wet gas recovery decreases monotonically as the stratification constant increases and is generally higher at the lower values of the wet gas content abandonment limits. The total gas throughflow first rises to a maximum as the stratification increases, and then ultimately declines. The effect of the areal sweep pattern efficiency is relatively minor as compared to that of the stratification constant, except in the region of low values of the latter where the formation is substantially uniform. The probability distribution can be characterized by a "variation" parameter varying from o to I as the formation changes from strict uniformity to extreme variability. The curves of total wet gas recovery and total gas throughflow to different abandonment limits of wet gas content versus the variation parameter have the same general characteristics as for the exponential permeability distribution. In the linear permeability distribution the ratio of maximum to minimum permeability also serves as a stratification constant index defining the distribution. The curves of total wet gas recovery and gas throughflow to fixed abandonment limits versus the stratification constant are similar to those for the exponential permeability distribution. However, for the higher values of the stratification constant the recoveries and throughflows do not asymptotically fall to o as in the latter, but approach constant values determined by the abandonment limit of wet gas content in the produced gas. Introduction It is becoming generally recognized that one of the most important factors determining the economic feasibility of cycling operations is the areal continuity and permeability distribution of the producing formation. While the effects of areal variations in permeability, porosity, thickness, and well pattern on the sweep efficiency can be evaluated by electrical model studies,' those due to permeability stratification require separate treatment. Several studies have been reported2,3 on the' influence of permeability variations on the wet gas recovery by cycling. In these, however, discontinuous permeability variations either have been assumed explicitly, or the analysis has been carried through as if they were discontinuous. While, in fact, the actual permeability profiles will undoubtedly be discontinuous, recent develop-

Jan 1, 1949

By H. L. Brunjes, G. B. Gould

The softening temperature of coal ash, as determined in the laboratory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfailing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heal was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investigations that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at temperatures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a heterogeneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening temperature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion. While the data are far from complete, covering as they do only a few coals, and while the conclusions to be reached from the data at this stage arc, in some measure, speculative, they are presented at this time because

Jan 1, 1940

By G. B. Gould, H. L. Brunjes

The softening temperature of coal ash, as determined in the laboratory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfailing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heal was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investigations that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at temperatures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a heterogeneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening temperature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion. While the data are far from complete, covering as they do only a few coals, and while the conclusions to be reached from the data at this stage arc, in some measure, speculative, they are presented at this time because

Jan 1, 1940

By D. Kok

A challenge in mine planning is the optimal allocation of resources to the appropriate workplaces within the shift cycle (labour, equipment type, and other resources) in order to carry out the shift cycle activities, achieve planned production targets, and ultimately maximize production within all infrastructure constraints. Generally, detailed mine planning is done on a monthly basis at a workplace level in order to determine the production targets. The production supervisor, mine overseer, or equivalent production manager must then make the appropriate resource allocation trade-off decisions on a daily basis per shift to try and deliver to the plan and required production target. Due to the complexity and number of permutations of possible resource allocation decisions, it is impossible for a human brain to make the appropriate and optimal allocation decisions that will result in achieving the maximum or target production. These allocation decision permutations must deal with the current status of workplaces (availability, position in the cycle etc.), the status of equipment availability (available, planned maintenance, or breakdown etc.), distance between the workplaces (traveling time of equipment between workplaces, etc.) and equipment type required for that shift cycle activity. All these factors need to be taken into account in resource allocation to plan for the shift, and even during the shift if a major piece of equipment becomes unavailable or a workplace activity is not progressing as planned. This paper is a case study on how an optimization algorithm can be used to create a production planning system for optimization of resource allocation in a mechanized underground platinum operation. A business case for optimal allocation of resources is demonstrated and compared to the current manual planned allocation.

Jan 1, 2012

By M. E. Coleman, G. Money

Pneumatic Conveying and Process Injection Technologies have been implemented in the metals markets for the last 40 years and have considerably improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider has turned its attention to supporting the Metals Market. Clyde seeks to utilise its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries.

Jan 1, 2008

By D. W. Philips

THE problem of strata control has of necessity been prominent in mining, and accounts of individual experience and research abound in the literature of most mining countries. Organized research began in Britain by the formation of a committee, upon the recommendation of the Safety in Mines Research Board in 1923, to investigate methods of reducing accidents from falls of roof in coal mines. This committee examined current practice in supporting underground workings in the principal coal fields, and its findings have been published in the Board's publications. Toward the end of these investigations it was suggested by the Chief Inspector of Mines that committees of the several mining institutes be formed to examine the problem in their respective districts. The formation of these committees marked a new phase in research on strata control. The work, though being done in the separate coal fields, followed a scheme outlined by the Chief Mining Engineer of the Research Board, and was coordi¬nated by his office. FACTORS INVOLVED The subject is being considered in Britain from two aspects: I. To provide, by supports, means to prevent falls of fractured ground. 2. To develop methods whereby the strata can be maintained in the least broken condition and thus make falls less likely. The first aspect is the one that will most likely lead to immediate results from the accident standpoint. It depends largely upon the assimilation of already acquired knowledge regarding the proper¬ties of supports and their correct applica¬tion. The second aspect is perhaps more fundamental, and involves also the proper¬ties of the strata and their behavior under the influence of the forces induced by mining. The problem involves many natural factors that cannot be controlled, such as depth, inclination and thickness of seam and nature of the rocks. Other factors, which may be considered to a certain extent controllable, cannot be varied readily and with sufficient fre¬quency to facilitate easy investigation; some of these are: rate of advance of the working face, length of face, direction of the face with regard to cleat and inclination, system and arrangements of rock packing behind longwall faces. In any given case the very many factors present have a mutual influence upon the effects produced in the mine. For example, a study of the effects of rate of advance cannot be done without considering the effects of other factors such as nature of strata, direction of face and quality and arrangement of supports. Conversely, the length and direction of a working face

Jan 1, 1946

By J Pearce, R Ramanathan

hortly after the World Health Organization declared COVID-19 a pandemic, the words ‘social distancing’ entered the global lexicon. The effects on the public of social distancing, lockdowns and travel bans are well documented. They also present unique challenges to the mining industry. For Hexagon’s Mining division, this posed a significant challenge. We have built our business – our reputation – on regional, customer-focused service and support. True to Hexagon’s values of being professional, engaged and customer-focused, we innovated to overcome the distance dilemma. Making automation a reality for our customers by implementing and supporting technology projects from a distance has helped deepen partnerships by making it easier to tap into our global experts’ knowledge. For example: • Body cameras were at the heart of a successful safety installation at a mine in Ghana. Despite the pandemic lockdown preventing travel by our South Africa staff into Ghana, the project was completed with minimal delays. • Traditionally, implementation and training for our Blast Movement Technology solution is done physically at the mine site. With COVID-19 travel restrictions in place, we have developed and successfully employed a remote deployment methodology. • Using RealWearTM headsets in the field and utilising the knowledge management platform from HINDSITE, Hexagon workshop technicians have been able to support hardware repairs in local offices, which once would have been undertaken in our overseas offices. • The same headset is being utilised to provide clients with remote mentoring sessions by our skilled team members who are based in our regional locations and unable to travel to their site without extensive quarantine commitments. • In instances where our team members have had to travel to site, we have provided consumer technology such as VR headsets to help them cope with long periods of quarantine to and from site. Post-pandemic, Hexagon will continue to refine and improve this method of working. INTRODUCTION Shortly after the World Health Organization (WHO) declared COVID-19 (COVID) a pandemic, the words ‘social distancing’ entered the global lexicon. As governments, healthcare organisations and the public scrambled to respond to the crisis, one thing became abundantly clear: isolation was and, for most of us, still is the key to maintaining our health. Hexagon, a leader in sensor, software and autonomous solutions, was well positioned to pivot and assist in the global response to the crisis. From simulations of the effects of social distancing to mapping the spread of COVID in real time, to drone technology delivering COVID tests, to providing communities with transparent geospatial information, Hexagon solutions continue to help ensure that innovation is readily available to those who need it most during uncertain times. The effects on the public of social distancing, lockdowns and travel bans are well documented. They also present unique challenges to the mining industry.

Jun 22, 2022

By Weng Fu

In this study, Resin-in-Pulp (RIP) technology is used to separate Pb from a chalcopyrite slurry. Solvent-impregnated resin, Lewatit® VP OC 1026, which contains di(2-ethylhexyl) phosphoric acid (D2EHPA) in a macroporous polystyrene matrix was used, as the functional group exhibits selectivity for Pb over Cu. Adsorption pH, kinetics, as well as resin and CuSO4 concentrations were investigated. The results show that the kinetics of Pb and Cu loading are fast, reaching the adsorption equilibrium within 30 min. The equilibrium pH of 2 was chosen as optimum for operation in order to achieve a high Pb extraction rate and extent as well as selectivity for Pb over Cu. High Cu(II) concentration in solution results in Pb(II) requiring a larger amount of resin for the same degree of extraction. Regeneration and reuse tests show that the loss of adsorption capacity happens in the 1st and 2nd cycles and then the adsorption capacity stabilises for the 3rd cycle.

By Dilip Sarangdhar

"SeaTech Solutions International (S) Pte Ltd, Singapore are the designers of world’s first seabed mining ship. The ship is now under construction and expected to be delivered next year. The Deep Sea Mining industry is eagerly awaiting commencement of her seabed mining operations and the success of this story will go a far way in accelerating investment in Deep Sea Mining and hopefully we should see many such projects take off and many such ships launched in the near future.Based on own experiences SeaTech discusses in this paper, various important issues that need to be considered for design of such Deep Sea Mining ships, the challenges faced and possible solutions to address them.From a ship designers’ perspective, there are not many direct previous references available, the seabed mining methods and associated equipment are also a new technology & products are still developing, there is no standard method and equipment for processing of mineral ore onboard, and above all there is the huge challenge of loading, storage and discharge of ore cargo efficiently in the confines spaces. Associated with the uncertainties of such issues is the uncertainty of weight, space, power, services and maintenance requirements, which can vary through the design and construction period and put the initial ship design at huge risk. Sufficient design margins need to be provided and a constant & strict control is absolutely necessary to ensure that the budget on each technical aspect is not exceeded. The local strength of the vessel particularly needs to be robust to take ultra-large loads due to huge equipment and their lifting /handling equipment/winches and tall mining process modules."

Jan 1, 2017

By C. P. Watson

It is perhaps significant that a few years ago the sessions held here were chiefly occupied with production. In the last two years these sessions have been concerned with production curtailment, unitization and conservation, notwithstanding that production in the United States in 1929 reached a total in excess of 1,000,000,000 barrels. A study of the leading producing units in the United States shows that Oklahoma, Texas and California in 1929 yielded 84 per cent. of the total production from 33.5 per cent. of the total number of producing wells. Production in the United States in 1929 showed an increase of 107,000,000 bbl. over the 1928 figures. This increase in itself perhaps is not enough to have caused the serious situation that is now confronting the industry. However, taking into account the gradual encroachment on the consumption of fuel oil through the greater utilization of natural gas, probably we have reached the point in the United States where prices will determine to a large extent,' in 1930, the amount that will be produced. In the states of Texas, Oklahoma and California, the most significant developmcnt of 1929 has been the desire of operators to reach some agreement to bring production more or less in control with the estimated demand. In November, production in California, particularly in the Santa Fe Springs field, was drastically cut to meet a certain requirement. Similarly, in Texas, the Yates field has been developed and has been producing under an agreement on the part of the operators; and more recently in Oklahoma City, serious efforts have been made to keep produetion in line with consumption. For the year 1930 we can see nothing in sight except drastic curtailment. This is a matter that I am sure is occupying the attention of all the leaders of the industry.

Jan 1, 1930

By Paul L. Russell

Introduction As the US and world population increases, so does the problem of supplying expanding energy needs. Early requirements worldwide were mostly met by abundant forest vegetation. Man's large scale use of minerals-energy resources is a fairly recent development. It occurred only during the past 200 years. Coal was the first mineral fuel to be used extensively. It was not a large factor in US energy production until the beginning of the 19th century. Petroleum and natural gas use is about 125-years-old. Electricity generation by falling water is about a century old. Atomic energy is only about 30-years-old. Extensive use of it is still in the future. Solar energy is in its infancy. Other energy sources such as wind, peat, and geothermal energy are minor and primarily of local importance. There were three main features of the fuel supply picture during the past 125 years. By 1900 coal replaced wood as the principal energy source. Since 1900, oil and gas have captured many coal markets. And after the mid-1970s, there was a resurgence of coal usage. (Figs. 1 and 2). Wood Until the advent of mineral fuels for energy, the major global energy source was wood. But populations increased and became centered in towns and cities. The problem of a sufficient energy supply first developed as nearby, easily obtained wood was exhausted. This problem became more acute as industries such as shipbuilding, smelting, and pottery making, became more widespread. Results of wood use as an energy source and building material are starkly evident in areas of the world where civilization is oldest. Entire forests were consumed and have never been replaced. In the US, wood supplied 90% of all fuel requirements until about 1850; and more than 50% until after 1880. By 1900, wood still supplied 20% of all energy uses. In the mid-1970s, energy costs increased, due largely to the oil embargo. This increase resulted in an increased wood demand for domestic heating. While large quantities of wood were being used, its share of the total energy market was still less than 3%. By 1983, wood was becoming increasingly scarce and more costly near most large US cities. Wind Wind powered ocean vessels for many centuries. Sailing ships were still common in 1900. Windmills provided an early, cheap energy source and continue to be used today on farms. Design and development of windmills for electricity generation is being conducted. Interest in wind power is growing worldwide where availability of wind currents warrants the investment. Also, US regulation requires power companies to "buy back" electricity generated by windpower in excess of that used by the windmill owner. Coal By the 1600s, England was producing, 900 kt/a (1 million stpy) of coal for heating and other uses. The first coal-fired blast furnace for iron smelting was developed in 1621. Coke-making was developed in 1755, and Watt invented the steam engine in 1769. Illuminating gas made from coal was introduced in London in 1800. During this same 200-year period, France and Germany developed coal production, but on a smaller scale than England. US, bituminous coal was mined near Richmond, VA, as early as 1748. Major bituminous coal-producing states in the early period were Pennsylvania, Virginia, Ohio, Kentucky, Illinois, and Maryland. West Virginia replaced Virginia as a major producer, when that state was formed in 1863. As the US expanded west, new coal deposits were found and exploited. Indiana, Alabama, Tennessee, Iowa, Kansas, Missouri, Washington, Colorado, Wyoming, Arkansas, Oklahoma (Indian Territory), Montana, New Mexico, and Texas had significant coal mining operations by 1900. Today the eight major coal producing states are Kentucky, West Virginia, Pennsylvania, Illinois, Ohio, Virginia, Wyoming, and Montana. These states accounted for about 80% of all coal (lignite, bituminous, and anthracite) produced in the US during the past several years.

Jan 8, 1984

By P. Saayman

The mining industry has much potential for automation. A great deal of work has been done on this subject and is still ongoing. With automation comes the possibility for optimization, because more information is available and actions can be repeated with more accuracy. This paper looks at possible solutions to the problem of optimizing the autonomous vehicle dispatch system in an underground mine. Possible optimization strategies are evaluated using a simulated environment. The majority of the results indicate that improvements on current methods are possible. Keywords: mining automation, simulation, vehicles, dispatching strategy, optimization.

Jan 1, 2006

By J. P. Jylhä, A. Jokilaakso

The Outotec Flash Smelting process is widely used in primary copper production. A layer of slag on top of matte (copper–iron sulphide melt) creates a barrier through which matte droplets descend. Droplets of different sizes settle through the layer at different rates, which increases possibility of copper losses as smaller matte droplets may be removed with the slag. In this work CFD-DEM (computational fluid dynamics – discrete element method) coupling was used to simulate matte droplets settling through the slag during slag tapping. Discrete droplets and slag flow were simulated with DEM and CFD, respectively. This new approach enables tracking and solving movement and interactions of individual droplets. User-defined models were created to take coalescence and reaction kinetics into account. Coalescence created larger droplets, while the reactions decreased droplet size and increased its density. Drag caused funnelling effect, which pulled droplets towards the centre line of the descending cluster. This research is the only study known by the present authors in modelling liquid-liquid systems with the CFD-DEM coupling. Simulating coalescence and chemical reactions for discrete droplets enables more realistic simulations. However, CFD- DEM simulations are computationally resource intensive already without additional models, so a full scale industrial settler modelling still waits for further increase in computer performance. INTRODUCTION Flash smelting is a method used in copper and nickel production. In the flash smelting process, oxidation of sulphides in a concentrate is used to release energy needed to smelt the feed. In the process, copper matte is formed. Matte has copper content in the range of 55 – 70% (Sridhar, Toguri, & Simeonov, 1997), the rest is mainly sulphur and iron but has still many other impurities (Taskinen, Seppälä, Laulumaa, & Poijärvi, 2001). Oxidized iron forms iron-silicate slag while SO2 is collected for acid production (Davenport & Partelpoeg, 2015). The Outotec flash smelting furnace (FSF) can be divided in four major component: concentrate burner, reaction shaft, settler and uptake. Concentrate, flux and oxygen enriched air are injected into the reactor through the concentrate burner. The mixture then reacts in the reaction shaft forming matte and slag, which are collected in the settler, while off-gases flow out of the reactor through uptake for heat and dust recovery, and SO2 collection for H2SO4 production. The matte and slag form separate layers due to immiscibility and density difference. Raw material feed is continuous, but the matte and the slag are tapped periodically. A flash smelting furnace is depicted in Figure 1.

Jan 1, 2019

By Frank H. Reed, P. W. Henline, Harold W. Jackman

A SUMMARY of the consumption of coal in 1945 shows that the coke industry accounted for 17 pct of the total coal used. No substitute for coke and the blast furnace in the reduction of iron ore has gained sufficient prominence so far to be given serious consideration. However, while the same slot-type ovens are being built and used now as were in use a few years ago, the problem of obtaining suitable coking coals, both high- and low-volatile, has forced many operators to revamp coal-blending facilities. Until the beginning of World War II, high-temperature coke plants were able to secure the required high-volatile and low-volatile coals from two or three seams and from three or four mines. Thus, many of our coke oven plants were able to operate with storage bins for two coals only. The variance in raw materials was not great, and uniformity of blend was a relatively simple problem. Since the beginning of World War II, many and important changes have taken place. Demand for all coals increased greatly. Production, though kept as near maximum capacity as possible, could not meet the demands for coal generally, and particularly for the various kinds of coal which have proved to be satisfactory for specialized uses; coals were allocated as nearly as possible in the order of greatest need; storage piling was reduced to the minimum necessary to keep plants in operation; uniformity of quality could not be maintained, and with this last, uniformity of composition of blends for coking could not be maintained. Whereas before the war producers of metallurgical coke could fill their needs from three or four mines, by the end of the war it was not unusual to find shipments to a single coke oven plant coming from as many as 30 different mines, in a single month. Since many of the mines producing both high- and low-volatile coal for high-grade metallurgical coke are rapidly nearing depletion, the problem of seeking new sources and of blending a number of coals in each plant for the production of high-temperature coke is facing practically every producer in the United States at the present time, and is one which will probably continue for many years to come. Midwestern by-product coke ovens in the Chicago and St. Louis areas use annually from 12 to 15 million tons of bituminous coals which are transported 500 to 700 miles from the Appalachian coal fields of Pennsylvania, West Virginia, and eastern Kentucky. Approximately two-thirds of this coal is high-volatile bituminous. The critical transportation problem confronting the nation in 1943, and the growing scarcity of the best Appalachian coking coals, prompted the Illinois Geological Survey to propose a research program in which would be studied the coking properties of blends of low-sulphur, high-volatile Illinois coal with the high- and low-volatile coals from the eastern fields. Such blends containing Illinois coal, if substituted for the all-eastern blends normally coked,

Jan 1, 1948

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941