Search Documents

By H. S. Martin

THE Phosphate Recovery Corporation operates three flotation plants, Nos. 1 and 2 concentrators about three miles northeast of Mulberry, Florida, and No. 3 plant at Wales, Tennessee. These plants represent the first commercial phosphate flotation operation and are also believed to be the largest nonmetallic flotation operation in the world at the pres-ent time. The details of this paper will be confined to plant No. 2, this being the newest and largest concentrator in Florida, and the flow sheet being practically the same as at plant No. 1. The No. 3 plant has been oper-ated but a short time and has been shut down since December, 1932, on account of the decrease in phosphate rock production. The phosphate washers usually are located centrally on a known deposit so that about two hundred acres of ground can be mined eco-nomically to each washer location. The washers are moved to new areas when the distance becomes too great for economical pumping. The flotation plants are built either adjacent to a washer, so that current debris may be utilized, or on the site of a former washer where there is sufficient accumulated debris available for mining, and the flotation plants must also be moved from time to time. Most of the water used in the Florida flotation plants is recovered after passing through a circulating system where most of the fine sus-pended matter is settled out, but some make-up water is obtained from deep wells near the plant. Power is obtained from the Tampa Electric Co. through the dis-tribution facilities of the International Agricultural Corporation. Flotation concentrate is hauled from the plant by trolley over the International Agricultural Corporation's trolley system, to the drying plant at Prairie, one mile northwest of Mulberry.

Jan 1, 1933

By Friedrich Steinhäusler

RADON SOURCES AND CONTROL MEASURES IN THE MINING ENVIRONMENT Most of the contamination of the mine atmosphere by radon 222 is due to radon emanating from solid or fractured ore surfaces of walls, roof and floor. Also radon gas emanates from broken ore either from storage in backfilled mined-out areas as applied in e.g. shrinkage stopping methods or from ore spillage along intake airways mainly due to the use of trackless haulage. To a lesser extent water itself can represent an additional source of radon, which emanates into air from open drainage ditches or seepages along intake airways. The contribution from water can be controlled effectively by isolating the water from the primary intake air system, e.g. by diverting the water through pipes and/or sealing of seepages by grouting. However, control of radon emanating from rock surfaces creates a major technical problem with significant impact on the economic aspects of mining operations, if adequate radiological conditions must be maintained. Basically this can be achieved by suppressing the emanation process itself, confining already emanated radon or by removal of radon from the mine atmosphere. Extensive research has been carried out on the rate of radon emanation as a function of barometric pressure changes (Pohl-Rüling and Pohl, 1969). It could be shown that the radon supply consists of a permanent and variable component. The former results from the surface of the rock and depends mainly on the emanating fraction of its radium 226 content; the latter originates from within the rocks and is a function of the suction effect of decreasing barometric pressure, rock porosity and fissures. The practical application of this barometric pump effect for depressing the rate of radon emanation, e.g. by pressurizing the mine atmosphere, is limited due to high costs for providing a sink for absorption of radon and air as well as lack of permeability in most uranium ore bodies (Schroeder et al., 1966). Mine air cleaning by removal of radon can be achieved with the use of cryogenic methods, chemical removal, adsorption into charcoal beds, use of a gas centrifuge or general ventilation techniques. Technical problems have so far prevented the application of any of these methods other than ventilation. It is common practice to use the age-of-air concept, i.e. fresh air is delivered to the worker as directly as possible and removed quickly afterwards thereby maintaining the air "young". Engineering principles for quantity distribution of air through underground working areas are straightforward for general mining situations where radon constitutes an environmental contamination problem. However, in cases of high uranium ore content this concept may result in high costs with regard to installation and energy requirements for effecting both frequent air changes as well as sufficient heating of the air in cold seasons. Taking into account that the investment in ventilation systems is a major cofactor for the overall ore production costs this can be a limiting and decisive component in the assessment of the economic feasibility of specific mining operations and mineral reserves in general. Effective control of the radon flux from the rock surface prevents the initial contamination of the mine air with radon directly at the source. A radon diffusion barrier for practical application in mining requirements should fulfill the following requirements: - reduction of radon emanation rate by at least an order of magnitude - high mechanical strength - ease of sealant application onto surface to be coated - water resistant - low fire hazard - resistant to temperature changes encountered in mines - high cost efficiency in relation to exposure reduction achieved (direct and indirect costs) - low degree of maintenance. In the past several materials have been tested as sealants for controlling the emanation of radon from surfaces of rock and building materials. Epoxy paints reduce radon emanation rate only by a factor of 2 to 6 (Auxier et al., 1974; Eichholz et al., 1980; Keith Consulting Engineers, 1980). Although it is possible to prevent the escape of more than 99 % of the radon to the environment with gel seals over 80 mm thick (Bedrosian et al., 1974), practical applicability is very limited. Multilayer coatings of epoxy resins with various additives require meticulous preparation and flawless application of seamless four-layer coatings in four days to impede radon diffusion (Culot et al., 1976), otherwise results from this method have not been totally satisfactory (Leung, 1978). Aluminium foil laminated with polyethylene and paper on each side is under test as radon barrier but results are not available yet (Ericson, 1980). However, this method has the inherent disadvantage that possible malfunctioning electrical installations can cause fire or electrical shock through the sealant. Polyurethane foam coatings have been used on stoppings as very effective sealants. It does, however, represent a potential danger of spontaneous ignition and it is expensive (Rock, 1975). Thus, there is still need for a material which has similar properties as outlined above. In the following results are reported from investigations on the suitability of various materials as radon diffusion barriers.

Jan 1, 1981

By H. C. Rolseth, J. J. Calaman

6.4-1. Principles of Operation. The jet-piercing process is a patented thermal process which depends upon a characteristic of the rock which is termed spallability. In its simplest terms, spalling is considered as decrepitation resulting from differential expansion of rock crystals due to thermally induced stresses. The number of individual properties influencing the spalling characteristics of rock are so numerous and their interaction so complex that the only truly reliable way to ascertain the spallability of rocks under thermal shock conditions is to expose them to these conditions. However, laboratory and field work have determined the principal thermal, physical, and mechanical properties of rock which affect spallability (10, 18). The approximate relationship between spallability and these characteristics is as follows: [ ] where To is the critical temperature at which, it is believed, a rock becomes elastic or sufficiently plastic to prevent further spalling action. Thermal diffusivity takes into account the amount of heat used in saturating the medium itself during the migration of a heat front. The rate and degree of dimensional changes which influence the spalling tendency of the rock will depend upon the characteristic of the heat gradient in the rock. The greater the spalling tendency, the higher the piercing rate. Those properties most favorable to a high degree of spallability are: 1. Large linear thermal expansion at temperatures below 700°C. 2. High thermal diffusivity at temperatures below 400°C. 3. Equigranular interlocking structure with little or no fine-grained clay or mica alteration products. 4. No significant amounts of soft, low-melting, or elastic mineral or materials which yield after thermal decomposition.

Jan 1, 1968

By Z. B. Karshigina, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva

At the present time of depletion of reserves of high grade rare earth deposits, it has become necessary to involve low grade raw materials in the production. Among the rare-earth deposits in Kazakhstan, the most advanced one is Kundybai. The mineralogical composition of ore is represented by the minerals: a-quartz SiO2, kaolinite Al2(Si2O5)(OH)4, muscovite KAl2(AlSi3)O10(OH, F)2, albite Na(AlSi3O8), rutile TiO2, and hematite Fe2O3. It contains: 59.1–68.5% SiO2, 19.1–28.4% Al2O3, 7.2–10.3% Fe2O3, 0.51–0.84% TiO2, 0.10–2.32% CaO, 0.39–2.10% MgO, and some other elements. Rare earths are located in the clay part (kaolinite, goethite) in the ion-adsorbing form, and they are represented by the main ore mineral churchite - YPO4·2H2O. In the ore the amount of rare-earth elements (total REEs) varies from 210 to 600 ppm. Elements of the cerium group predominate (La, Nd, Ce, Sm, Pr) and the yttrium group is represented by Y, Gd and Dy. Extremely thin intergrowth and accumulation of REEs in clay minerals cause difficulties in their recovery using flotation and gravitation beneficiating methods. The purpose of this work is the development of an extraction method for the main mineral components of ore with transfer of the total REEs into the solution with high extractive efficiency. Results of the experimental work into high-temperature processing (hereinafter referred to as sulphatization) of ore by sulphuric acid with subsequent dual-mode water leaching of the sulphate product (sinter) are presented in this manuscript. The influence on the ore sulphatization process of some physical and chemical parameters: liquid-to-solid (L/S) ratio (0.36–0.86 cm3/g), temperature (100 – 500°?), concentration of sulphuric acid (3.0–18.62 mol/L) and duration (0.5–2.5 h) was studied. Optimal technological parameters of the process were determined to be: L/S ratio 0.36–0.46 cm3/g; temperature 500°?; concentration of H2SO4 9.0 mol/L; soaking time 1.5 h. Under these conditions it is possible to obtain extractions of ~ 85% REE, as well as 58% aluminium and 10% iron. XRD and IR-spectroscopy analyses were used to determine the material constitution of sulphated cakes obtained under optimal conditions. It was found that the primary minerals are quartz and muscovite; however different sodium aluminium silicates and albite minerals are present as well. In the future, it is proposed that the leach residue cakes are processed into precipitated silica (“white soot”).

Jan 1, 2016

By P Gnnther, A M. van Niekerk

Coal mining operations in the Upper Olifants River Catchment in the Mpumalanga Province of South Africa are challenged with the increasing production of excess mine water that cannot be fully managed by existing practices of pollution control at source, recycling, and reuse on mining sites, storage and limited release to the natural water course. In contrast to this, the Olifants River Catchment is experiencing water stress and insufficient water is available to satisfy all water quantity and quality requirements for future industrial and municipal growth. It is estimated that the catchment has a deficit of 192 million m3 per annum if the reserve water requirements are taken into account. The future increased water requirements can be met by water transferred to the Olifants River Catchment from adjacent catchments. The cost of transferred water is likely to be substantially higher than the current cost of water supplied to local municipalities, commerce and industry. BHP Billiton and Anglo Coal Corporation are working together to jointly implement water management strategies that will contribute to the achievement of in-stream and dam water quality and aquatic objectives for the catchment. Consideration is now being given to the treatment and beneficial use of excess mine water. This will inaugurate a new era for the coal mining industry in South Africa, in which a pollution threat to the water resources in the Upper Olifants River Catchment is converted into a water source for beneficial use. Three potential mine water reclamation and reuse schemes have been identified and this paper details the technical, institutional, legal and financial considerations in the implementation of these schemes.

Jan 1, 2006

By Robert B. Parsons

"Several recent cases indicate that the Courts may be leaning toward a more favourable treatment of mine closing and related costs. In this article, we look at two recent cases, Burnco Industries Ltd. and Nomad Sand & Gravel Ltd. The former was heard before the Federal Court - Trial Division and the latter before the Tax Review Board.It appears that in certain situations mining companies may now be able to sustain current deductibility of estimated mine closing costs during the productive years of the mine, rather than waiting until either the date on which mining ceases or the reclamation and similar activities commence. This would be of great benefit to the mining industry, as waiting until the bitter end often means that there are no revenues available against which the expenses may be offset and, hence, no tax relief.IntroductionUnder the Income Tax Act in Canada, taxpayers are not permitted any deductions in respect of an outlay or expense in determining income from a business or property, except to the extent that such expenditures are made or incurred by the taxpayer for the purpose of gaining or producing income. In addition, no deductions are permitted for amounts transferred or credited to a reserve, contingent account or sinking fund except as expressly permitted by the Act.In large measure, these provisions are relevant to the mining industry to the extent that they determine the periods during which expenses may be charged against revenues for income tax purposes. Several recent cases have indicated that the Courts are leaning toward a more favourable treatment of accrued costs in the mining industry than was previously considered to be the case."

Jan 1, 1982

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly 'safe' compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By D. J. Bauer

A pure scandium solution was concentrated from 10-4 mole per liter to 0.5 mole per liter by continuous foam fractionation in a spaced, packed column. Recovery in the foam was 77 percent using a spaced, packed draining column with sodium n-methyl-n-"coconut oil acid" taurate as the surfactant. The technique was first studied batchwise in a small unpacked column to determine the more important variables. Optimum surfactant concentration was found to depend on scandium concentration. Extraction and, in general, enrichment ratios were highest in the 2.5 to 3.5 pH range at temperatures ranging from 50° to 70° C. An airflow rate of 136 ml./min. was satisfactory in the equipment used.

Jan 1, 1962

By Tyler DB, Thin LGT

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications are made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a new squat pillar empirical strength relationship.

Jan 1, 1992

By William H. Pomroy, Shail J. Butani

"This Bureau of Mines publication presents a statistical analysis of official U.S. Mine Safety and Health Administration (MSHA) metal and nonmetal mine fire reports from 1950 through 1984, plus accounts of selected nonreportable fires (less than 30 min and no injury) and opinion data on fire hazards from mine safety directors. Fires were analyzed by time trends, ore type, ignition source, burning substance, location in mine, equipment involved, means of detection, duration, number of injuries and fatalities, mining method, and successful extinguishing agent. The leading ignition sources were electricity in underground fires and engine heat in reported surface fires. The most frequent burning substance was combustible liquids for all nonreportable fires, reported surface fires, and reported underground fires from 1978 to 1984. For underground fires reported prior to 1978, timber was the leading burning substance. Mobile equipment was the type most frequently involved in both underground and surface fires. Underground fires occurred most often in haulageway or drift areas, and reported surface fires occurred most often in plant and mill buildings, while most nonreportable surface fires occurred in other areas. The most common methods of extinguishment were water hose lines for reported fires and dry chemical handportable extinguishers for nonreportable fires. INTRODUCTIONIn support of the Bureau of Mines research on mine fire protection, two separate baseline studies on mine fire incidents have been prepared. The first study addressed coal mine fires. The results of that study are summarized in the Bureau's Information Circular 8830, ""A Statistical Analysis of Coal Mine Fire Incidents in the United States From 1950 to 1977."" This second report, addressing metal and nonmetal mine fires, is the companion to IC 8830. Together, these two reports provide a comprehensive, factual summary of the mining industry's fire experience.This report, like IC 8830, covers (1) MSHA fire incident reports, (2) records of nonreportable fires (less than 30 min and no injury), and (3) mine safety directors' opinions on fire hazards. The MSHA fire reports provide the most reliable, objective, and accurate historcial record of the major noncoal mine fires that occurred during the study period (1950 through 1984). However, MSHA fire reports alone understate the true magnitude of the fire problem because metal and nonmetal mines have been legally required to report fires to MSHA only since 1968. Although some fires were reported prior to 1968, doubtless a great many were not. Also, the reporting regulations that took effect in 1968 specify that only fires lasting 30 min or longer or involving an injury need to be reported. MSHA fire reports are thus limited in scope by MSHA's legal authority. In order to provide a more comprehensive data base, it was also necessary to gather and analyze mine company records of nonreportable fires."

Jan 1, 1986

By C. J. Hall

The simplest natural ventilation cycle is similar to a Joule or Brayton cycle. This comprises two reversible adiabatic processes in the shafts and constant pressure processes underground and on surface. The thermal efficiency of such a cycle is given by the temperature increase in the downcast shaft divided by the absolute temperature of the air at the bottom of the downcast shaft, and is independent of the temperature increase underground. This efficiency is comparable to the Carnot efficiency, which is the greatest possible value between constant temperature reservoirs, source and sink. Two variations of the Joule cycle are investigated, using numerous work examples. In the first, dry air is used as the working substance, a fan is provided at the top of the upcast shaft, and various mass rates of flow are used with frictionless shafts and a constant resistance value in the horizontal mine workings. The lost work less the fan work gives the natural ventilation work, and this divided by the enthalpy increase in the workings gives the thermal efficiency. The thermal efficiency increases dramatically with mass rate of flow, although the enthalpy increase remains constant. This appears to violate the second law of thermodynamics, since the frictionless case has a Carnot efficiency. When the lost work is added to the enthalpy increase, however, the efficiency decreases slightly from the Carnot value, to conform with the second law. This increase in efficiency with mass rate of flow is often referred to as the reheat effect, although the air is not heated. The second investigation is similar to the first, except that the air entering the downcast shaft contains a small amount of water vapor, and there is evaporation in the mine workings only, until the air entering the upcast shaft is saturated. There is, of course, condensation in the upcast shaft. In this case, it is not possible to calculate the Carnot efficiency, but the thermal efficiency is 20 to 40% of the similar dry air values. This decrease is much more than can be accounted for by the larger value of specific heat for water vapor. In addition, the natural ventilation work is almost constant with increased mass rate of flow, and the thermal efficiency based on heat addition tends to decrease. The thermal efficiency based on heat and lost work decreases in conformity with the second law. The reasons for the differences in behavior between dry and moist air are not readily apparent.

Jan 1, 1991

By C. McDonald, S. Slottee

Deep "paste" thickeners have been used in the alumina industry for several decades to improve chemical recovery and allow “stacking” of the red mud for disposal. These paste systems have eliminated many traditional tailings ponds in addition to providing better tails washing and better water recovery. This technology is not widely used or understood in other mineral processing applications. However, there is growing worldwide recognition of the advantages of concentrating mill tailings to a “paste”, i.e. a solid suspension that does not settle or segregate. This technology offers several alternatives to the traditional tailings pond such as “stacking” or mine backfill. More water recovery is possible than with high rate thickeners. Process benefits come in the form of better chemical and metals recovery through better washing in counter current decantation (CCD) applications. Obtaining a true paste (non-segregating suspension which exhibits a yield stress) and understanding the handling characteristics for applications outside alumina, are recent developments. Achieving all of the benefits available from a paste system requires careful design that takes into account the specific requirements of the disposal application along with the peculiar difficulties in producing and handling paste. In fact, design of a paste system is markedly different from a conventional system. Project design usually requires the cooperation of experts in several interrelated specialties including geotechnical, thickener design, pumping and discharge design and controls. A successful project must coordinate all activities to ensure that the overall objectives for the project are achieved. This paper describes the properties of paste, reviews the applications, and discusses the design of a complete paste deposition system.

Jan 1, 2003

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6'7 grain boundaries and possibly twinning planes.8'9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5'6'9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6'7 grain boundaries and possibly twinning planes.8'9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5'6'9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By William E. Wallace, Michael J. Keane

This review summarizes three sets of ongoing studies which we are performing in collaboration with a number of researchers associated with the Dept. of Interior - Generic Mineral Technology Center for the Study of Respirable Dusts, concerning surfactant-particle interactions studied using this surrogate surfactant. These topics are: (A) the suppression of mineral particle cytotoxic potential by DPL adsorption and the persistence of this effect under conditions of enzymatic digestion; (B) surfactant suppression of organic particle cytotoxicity by DPL adsorption and the effect on subsequent expression of genotoxic potential; (C) potential effects of surfactant on heterogeneous structured complex respirable particles. The references list some of our reports which can provide additional information on these studies. Further, those reports provide references to the literature of the field and to the works of others on these topics. Deep lung airspaces, the pulmonary alveoli and respiratory bronchioles, are coated with a hypophase which is rich in surfactant biomolecules secreted by the alveolar type II epithelial cells. The surfactant is known to be critical to maintaining stable low surface tensions on the inner surfaces of the alveoli by forming a surfactant layer on the airliquid interface of the alveolar hypophase. Upon deposition in the acinar regions of the lung a respired particle's initial contact will be with this surfactant coating over pulmonary tissue. A primary component of this surfactant is the phospholipid diacyl glycerophosphorylcholine, commonly called lecithin. A surface layer of dipalmitoly lecithin on saline will act much as full pulmonary surfactant in decreasing surface tension and producing a hysteresis in surface tension behavior with surface area. We have used dipalmitoyl glycerophosphorylcholine, or dipalmitoyl lecithin (DPL), a major component of that surfactant, dispersed in physiologic saline as a surrogate for studying interactions of both mineral and organic respirable particles with pulmonary surfactant and consequent effects on particle toxic behavior. A. DUST CYTOTOXICITY AND LECITHIN SURFACTANT ADSORPTION Respirable quartz and kaolin clay particles are found to be comparably cytotoxic in a number of in vitro bioassays including lavaged rat pulmonary macrophage release of cytosolic and lysosomal enzymes, and red blood cell hemolysis as a measure of dust membranolytic potential. These direct and prompt cytotoxic activities do not account for the distinctly greater potential for quartz to induce pulmonary disease. When respirable quartz and kaolin are incubated with a dispersion of DPL in saline at 37C it is found that the prompt cytotoxicity of both dusts is fully suppressed as measured in vitro by pulmonary macrophage release of lactate dehydrogenase, beta-N-

Jan 1, 1991

By Howard Hughes

IN drilling for water and oil to reasonable depths through the generally soft yielding clay and sand formation of the Coastal Plain of Texas, . Louisiana, and Mississippi, the rotating method of drilling was adopted, principally on account of the easy and quick penetration, and the low cost of the drilling plant. In favorable ground, free of heavy gravel and rock strata, as much as 1,000 ft. has been drilled in less than 36 hr., although such performances were of course rare. Hydraulic rotary drilling, or, as it is now called, rotary drilling, was used in the above States as early as 1880. The plant consisted of an ordinary derrick, a 25-h.p. boiler, a small hoist, a steam pump, and a water swivel with hose attachment, and an ordinary flat diamond-pointed bit. The successful drilling in of a phenomenal oil well by this process on Spindletop, near Beaumont, Texas, on Jan. 10, 1901, and the ascertained impracticability of drilling subsequent wells in the same locality by other methods (owing principally to heavy quicksand under pressure from below), brought rotary drilling into great prominence, practically to the exclusion of any other process throughout the Coastal Plain, and later on elsewhere. The method, as its name implies, involves the rotation of a pipe by means of machinery placed on the derrick floor. A drill bit attached to the lower end cuts a clearance for the drill pipe, with much the same motion and effect as an auger. Water forced through the drill pipe by means of a pump, and escaping through the bit, removes the cuttings and returns to the surface outside the drill pipe. In this manner the hole is kept open, permitting the drill stem to rotate freely. The pressure of the column of muddy water holds up the walls of the hole until it has been cased. Practically all the wells of the Gulf coast region, numbering nearly 10,000, have been drilled with this system. During the last five years its use has been extended to many other States and countries.

Jan 3, 1915

By Wenming Wang, Edgar E. Vidal, Scott A. Shuey, Patrick R. Taylor, Judith C. Gomez

Introduction In modern society, vanadium is defined as a strategic metal. Some 90% of the global consumption is used as an alloying agent for carbon steels, tool steels, and high-strength low-alloy steels (particularly for pipelines). Advanced titanium-aluminum-vanadium alloys are seeing application in the aerospace industry. Small but ever growing amounts are finding application as catalysts or in electronics. New uses are continually being discovered for this metal. One example of a new application is the vanadium-redox battery for use in generation plants and back-up power sources. Vanadium is found in a large number of minerals, of which the most important are carnotite, roscoelite, vanadinite, mottramite, and patronite. Just over a third of the world's vanadium is produced as a primary product; the balance is a by-product of the iron and steel, oil refining, power generation and uranium enrichment industries. Vanadium can also be sourced by recycling spent catalysts from the petrochemical industry and ash produced by the combustion of oil emulsion in power stations. However, recycling activities are believed to account for only a small amount of total world supply. Vanadium is recovered from these ores largely as the pentoxide (V2O5) [1]. The major sources of vanadium-bearing magnetite ores are scattered throughout Australia, China, Russia, and South Africa. Current estimates of world’s Proven & Probable vanadium reserves are of the order of 41.3 million tones [2, 3]. Commercial vanadium-bearing titaniferous magnetite deposits can be found in Kachkanar, Russia; Pan Zhihua, China; Bushveld, South Africa; and Windimurra, Western Australia [4]. Other deposits have been found in New Zealand, Canada, and India, among other countries. Vanadium consumption in the steel sector has increased some 7% per ton of steel over the last 10 years as new alloying applications have been found to improve steel's strength-to-weight ratio. Future demand from the aerospace and nuclear industries for non-ferrous vanadium alloys such as titanium and super-alloys is also likely to grow. Vanadium is usually added in the form of ferrovanadium, a vanadium-iron alloy. Vanadium compounds, especially the pentoxide form, are used in the ceramics, glass, and dye industries, and are also important as catalysts in the chemical industry. While established approaches may be used at an industrial scale to treat vanadium-bearing titaniferous magnetite ores in several countries, new alternatives are being developed worldwide. This review will give short overview of the treatment of vanadium-bearing titaniferous magnetite ores, an overview of direct reduction and direct smelting processes and an approach to determine technical alternatives for the property.

Jan 1, 2005

By H. D. S. Miller

"This paper introduces a new approach for the design of rib pillars. The approach involves an empirical method for pillar design and a discussion of the pillar stability used for open stope mining methods.The empirical method predicts the degree of stability of rib pillars. Pillar load is estimated using two and three dimensional numerical modelling. Rock strength and the shape effect of pillars are used to account for pillar strength. The method has been calibrated with case histories from Canadian open stope metal mines and is compared with other methods used [or pillar design.INTRODUCTIONThe role of rib pillars in open stope mining is to provide stability to a mining block by limiting rock mass displacements and restricting the exposure of a rock mass in stope backs and stope walls. They also provide flexibility in ore extraction by dividing a stope block into multiple working faces.The use of backfill in open stope mining methods has reduced somewhat the need for optimum pillar design. In contrast to permanent pillar methods, the dimensions do not need to be minimized because the pillars are usually recovered in a later stage of mining. However, the consequences of poor pillar design are often overlooked and can still be severe. A pillar that does not perform its intended role may result in excessive stope or pillar sloughing, difficult and expensive pillar recovery, loss of permanent access and remedial costs such as development rehabilitation, artificial support or low productivity.Pillar design concepts of the past were not developed for open stope mining conditions and generally have not been confirmed for open stoping. The focus of this paper is to introduce an empirical design relationship specifically for open stope pillars. It provides a stable, yielding or failed pillar assessment for a given design."

Jan 1, 1989

By Shahid Islam, Lucian Bogdan

There is a rapid expansion of world’s infrastructure and simultaneously existing infrastructure is aging. The maintenance of infrastructures has been of particular concern to the engineering community. Monitoring and evaluating the structures have become more significant than ever. Ground anchor is an important part of the structure where it is installed. Unfortunately there are limited testing methods available to assess the force in the pre-stressing steel. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYNA Force sensors have been developed to measure the force in the pre-stressing steel during construction and at any time during the lifetime of the structure. These sensors make use of the magneto-elastic properties of ferrous materials. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. They can be used for bare, epoxy- coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the tendon. It measures the force of the steel element at the location where it is installed and can be recorded manually, automatically, or remotely. The sensor is robust, requires no maintenance and it is expected to have a similar service life to that of the surrounding structure. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. Sensor readings provide a second measurement, in conjunction with the jack pressure gauge, of the post tensioning force during initial testing procedure for ground anchors. This paper describes its application in tie-back and tie-down anchors and force monitoring of retaining walls, bridge abutment and dams where the data were collected manually, automated and remotely. INTRODUCTION Our infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.

Jan 1, 2018

By Sanjeeva Latchireddi

"Deteriorating ore grade and high demand of metals has tremendously influenced the unit capacity of SAG mills. Pebble circuits have been added to the existing SAG circuits to increase their unit capacity. To make the pebble circuits justifiable, the grate openings are increased almost to 4.5 inches to draw large quantity of pebbles. The inherent transportation problems associated with SAG mills in closed circuit with pebble fraction are more complicated than the single stage SAG mill operation, because the coarse pebbles behave significantly different to that of slurry in pulp lifters. In addition, operation of mills at higher speed, to take advantage of precise design of high release angled shell lifters significantly reduces the discharge efficiency of the conventional pulp dischargers. The presence of a sizable quantity of pebbles in the pulp lifter limits the space available and reduces the flow gradient through the grate thus increases the load inside the mill and hence the mill power-draw. This paper analyses all the problems associated in discharge of slurry and pebbles in SAG mills with pebble circuits. The Outokumpu patented Turbo Pulp Lifter (TPLTM) aims at eliminating the inherent material transport problems to ensure good grinding conditions. Recent installation of TPLTM in a 26-ft SAG mill has proven these claims by reducing the specific power consumption while increasing the mill capacity.INTRODUCTIONThe conventional wisdom is to look at the semi-autogenous grinding (SAG) mill as just another grinding mill in which ball charge, mill filling, and mill speed are varied to attain maximum throughput. Liner design for the SAG was also approached more from a wear perspective rather than a metallurgical and hydraulic-flow perspective. The extensive research work carried out by Latchireddi and Morrell (1997,2003a and 2003b) has demonstrated to think of the SAG as more of a pump in which the grates and pulp discharger end (“impeller”) were designed to efficiently discharge the product sized particles smaller than the grate size with minimal recirculation out of the mill.The rock load in the mill is essentially depends on ore characteristics and the discharge rate of broken particles. The discharge rate of the product material depends on how efficiently the discharge pump (grate and pulp lifters) is operating. Similar to the impeller design affecting the pump capacity, the pulp lifter design affects the discharge capacity (or mill throughput) of the SAG/AG grinding mills. The general arrangement of AG/SAG mills discharge system is shown in Figure 1."

Jan 1, 2007