Search Documents

By AIME AIME

THE non-ferrous 'metals industry of the Soviet Union found itself in a very low position at the beginning of the reconstruction period in 1922, due to the absence of modern smelters and the run-down condition of the existing ones. Up to. 1924 there was no great demand for newly smelted non-ferrous metals due to the considerable stocks' of copper, zinc, lead, tin and aluminum in the courtry and also to the undeveloped condition of Soviet industries. However, in 1925 it became necessary to obtain new stocks of non-ferrous metals and in that year 12,000 tons of zinc, 14,000 tons of lead and 2,000 tons of tin and aluminum were imported into the U. S. S. R.

Jan 1, 1929

By Sheryl D. Gallagher

The project consisted of filling an abandoned underground limestone mine to facilitate construction of a new entrance ramp to I-470 in Lee?s Summit, Missouri. Due to collapse of mined areas near the project site, design included determination of the limits of remediation for the project and minimum construction requirements for mine infilling. The Judy Company, contractor selected for the mine infilling, experimented in the laboratory with several grout mixes to determine the appropriate mix for the project. Infilling was accomplished from the ground surface, and camera observation was used to monitor the barrier wall construction and infilling process. It was discovered that some of the mapped rooms were larger and some were smaller than indicated on the construction plan.

Jan 1, 2009

By G. W. Norval, V. G. Papangelakis, G. A. Moldoveanu

Smelting has been the primary method of treatment for refractory copper sulfide concentrates such as enargite (Cu3AsS4), but the pyrometallurgical processing generates elevated levels of volatile arsenic. The present research investigates a novel hydrometallurgical process of oxidative dissolution of enargite at ambient conditions in the presence of chlorine dioxide (ClO2), a very powerful oxidant generated in solution by the reaction between a strong acid (HCl or H2SO4) and sodium chlorite (NaClO2). The effects of initial oxidant concentration, particle size, agitation speed and temperature on dissolution kinetics and copper extraction were investigated. It was found that a stoichiometric ratio of ClO2:Cu3AsS4 = 9:1 were needed to completely and congruently dissolve the mineral with fast kinetics (<15 minutes) under ambient temperature. The dissolution extent (metal extraction) increases with increasing ClO2 concentration and decreasing particle size of solids, but is not influenced by temperature or agitation speed.

Jan 1, 2014

By R. C. Ferguson, Harlowe Hardinge

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,&apos; believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months&apos; test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors&apos; reply)—For one, I heartily agree with Mr. Johnson&apos;s opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one&apos;s figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer&apos;s analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By Harlowe Hardinge, R. C. Ferguson

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,&apos; believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months&apos; test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors&apos; reply)—For one, I heartily agree with Mr. Johnson&apos;s opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one&apos;s figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer&apos;s analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By Bo Liang, Hongmin Zhu, Kai Huang, Shafiq Alam

A new approach of recovering platinum and palladium from electronic wastes by hydrochloric acid leaching followed by selective adsorption on low-cost and environmentally benign biomass sorbent prepared from easily available agriculture waste is suggested. The obtained adsorbents were prepared by a combination of chemical modification and hydrothermal carbonization process with (NH4)2C2O4. It was found that the maximum adsorption capacity of hydrothermal carbonized garlic peel for Pt( ) and Pd( ) was 1.64 and 0.42 mol/kg respectively. The Langmuir adsorption isotherm was applied to describe the adsorption process. Kinetics of the Pt( ) and Pd( ) ions adsorption was found to follow pseudo-second-order rate equation. The adsorbents were examined by scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FT-IR). Based on the characterization results, a possible mechanism of Pt( ) and Pd( ) ions adsorption with the hydrothermal carbonized garlic peel was proposed. This study provides a promising adsorbent with efficient adsorption property for platinum and palladium recovery from the leach solution of electronic wastes.

Jan 1, 2016

By Pathies Nawej Muteb, Tom Strombotne, Karl Leetmaa, Irma Gabric, Keith Darby

"Continuous control of the final grinding product size is important to optimize gold liberation for Gold Milling operations. At Meadowbank Mine an on-line Particle Size Monitor has been employed successfully to achieve the targeted final grind which leads to optimizing the gold recovery at maximum grinding circuit throughput. The live monitoring of the final product particle size leads to a maximum grinding circuit throughput every minute during the process. This paper discusses the optimal utilization of the Particle Size Monitor to assist the Mill operator to maximize the grinding circuit throughput as the milling conditions change due to variable ore processed at Meadowbank Mine. Also the paper includes the usage of the Particle Size Monitor to guarantee the final grind target at each instant of the process.IntroductionAgnico-Eagle is a Canadian-based company that Trades on the TSX & NYSE (AEM). It owns eight mines (8) operating in Nunavut, Quebec, Finland and Mexico and has more than 7,500 employees (Figure 1). 1.6 M ounces of gold were produced in 2015 and the annual average annual production from 2016 to 2018 is forecast to be approximately 1.53 million ounces of gold.The Meadowbank Mine is located in Nunavut, Canada (Figure 2). The mine opened in 2010 and from 2010 to 2014 a total of 1.8M oz of gold was produced. The milling rate is 4.2 Mt per year with an average mill throughput of 11,900 tpd or 496 tph. Average annual gold production over life of mine is expected to be 450,000 ounces. Meadowbank has 775 employees, of which 265 are Inuit or 36% of the total workforce. Estimated life of mine is 2010 to 2018. Gold production in 2015 was 381,804 oz. Meadowbank was Agnico-Eagle’s largest Gold producer in 2015."

Jan 1, 2017

By L. Bryson, J. H. W. M. Brits, K. Voogt

"The Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) has the world’s first full deposit nickel plating tankhouse. Impurities in the nickel electrolyte can induce stresses in the electrowon nickel deposits that could lead to delamination of the deposit. Identifying the impurities that contribute to increasing internal stresses in the nickel deposit is key to successful operation and automation of the tankhouse. Impurities were introduced in the plant electrolyte and the effects on the full-scale nickel deposits evaluated. The impurity-adjusted electrolyte solutions were also analyzed using commercially available bench-scale methods to determine the induced stress. A correlation between impurity-induced deposit stress and full-scale delamination was developed. A direct correlation can now be made between feed quality, i.e. impurity concentrations, and degree of delamination in the plant. This methodology has the potential to rapidly predict the effect of new reagents, upstream process upset conditions and synergistic interactions between impurities on deposit stress and delamination of nickel deposits.INTRODUCTION Nickel electrowinning in sulphate media was first pioneered by Outokumpu in its Harjavalta refinery in 1960 (Saarinen and Seilo, 1985). The original process was very manual with starter sheets plated onto “acid resistant” steel for 36 hours and then manually stripped and cut into sheets which could be inserted into the main production cells for a further 4–5 days. The starter sheet stripping and manufacture process was later automated. The same technology was subsequently implemented on a number of plants around the world. Anglo American Platinum’s Base Metal Refinery (BMR) began nickel electrowinning in the early 1980’s. The recent expansion of Anglo American Platinum’s Base Metals Refinery necessitated the construction of a new nickel tankhouse to achieve two primary objectives. The first to increase the capacity to 32 400 tpa nickel and the second to reduce employee occupational exposure to nickel aerosols. The new tankhouse has been commissioned and is in the process of ramp-up; more details are given by Hagemann et al. (2016). Fundamental to lowering employee exposure to aerosols was automating both harvesting and final handling of cathode. In order to accomplish this a bold move was taken to plate up to 10 days on permanent titanium blanks which are harvested by automatic crane and automatically stripped. The original development work for the plating nickel on titanium blanks over a ten day cycle is given by Bryson et al. (2006)."

Jan 1, 2017

By B C Tanda, E A. Oraby, J J. Eksteen

"Base metal and precious metal deposits are well known for their significant geometallurgical variation throughout the volume of the proven resource. At the metallurgical level, the plant normally processes an upper oxidised layer, a transition zone and a sulfide zone, often leading to different processing techniques for the different zones. A novel processing approach is presented whereby alkaline leaching with glycine is used to leach base and precious metals, using a copper-gold ore deposit as a case study. Glycine is a cheap, non-toxic, non-volatile, highly water-soluble crystalline solid produced industrially in bulk quantities. As a chelating ligand it forms a number of stable glycinate complexes with Ni, Co, Cu, platinum group metals (PGMs), Au, Ag, Zn, Pb, Hg and Cd, with broad stability regions over an extended temperature-pH-Eh range, allowing dissolution of these metals in the neutral and alkaline regions (pH 7–13). It has been shown that this lixiviant system can leach the metals from their oxide, oxy-halide, basic sulfate, carbonate, native and various sulfide forms, including refractory sulfides such as chalcopyrite. Extraction of the metals from their soluble glycinates is easily achieved using a range of solvent extraction and precipitation processes, and the glycine remains stable in aqueous solution for recycle and reuse. Minerals bearing metals in Groups 1 to 8 of the periodic table are normally unaltered. This technology therefore provides a highly selective leaching environment for the extraction of numerous scarce metals of economic interest, with minimal interaction with gangue minerals, whilst using environmentally benign reagents. Problematic leach residues such as jarosites, elemental sulfur and silica gels are averted through this processing approach. This technology allows hydrometallurgical processing that is much less domain-sensitive in the geometallurgical sense, and utilises essentially the same key reagents for the whole deposit.CITATION:Eksteen, J J, Oraby, E A and Tanda, B C, 2016. Developing Robust Hydrometallurgical Processes to Recover Metals from Deposits with Large Geometallurgical Variation, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 15–20 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By K. S. Lackner, T. M. Yegulalp

We present a review of research and development for coal based clean energy systems aiming for zero emissions to the atmosphere. These systems can utilize all kinds of coal or other solid carbon sources such as tar sands as well as liquid hydrocarbons. The chemical energy of carbon is transferred to hydrogen and used in power generation, in fuel cells, or hydrogen combusting turbines. The waste products of these future power-generating systems are ash, sulfur compounds and CO2. We also summarize current and developing technologies for processing of CO2to produce mineral carbonates for permanent disposal, and associated byproducts.

Jan 1, 2003

By A Hoyle, P Walker, D Bennett

The Phu Kham copper-gold operation located in Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited, based in Brisbane Australia, holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining 10 per cent held by the Government of Laos PDR.The 12Mt/y copper-gold concentrator at Phu Kham commenced production in April 2008. Flotation copper and gold recovery from commissioning was consistently poor, due to the high levels of pyrite and problematic secondary and oxide copper species and non-sulfide gangue.The low recoveries of copper and gold from Phu Kham were recognised during the feasibility study design phase. A bulk sulfide flotation regime in roughing produced high recoveries, however a large capacity cleaning circuit was required and there was risk of not meeting saleable concentrate grade specifications. The installed design offered a capital efficient compromise to ensure that a concentrate grade of 24% copper could be achieved at acceptable recoveries.Incremental improvements in copper recovery were achieved by 2011 through conversion of conditioning cells to flotation cells in both roughing and first cleaning and increased cleaner capacity through the installation of a Jameson cell. In 2012 the Phu Kham Upgrade Project was commissioned to increase mill throughput, along with additional rougher and cleaner capacity to increase residence times at the nominal 16 Mt/y throughput. The marginal reduction in primary grind size due to the additional ball milling power also provided a small recovery improvement.This paper presents the development, design, implementation, and performance of the Increased Recovery Project commissioned in April 2013 which targeted the major causes of copper loss from the circuit. Based on fundamental and detailed test work and mineralogical analysis of concentrator streams, an optimised design was developed which has increased copper and gold recoveries by over 5% and 10% respectively. The Increased Recovery Project has positioned the concentrator to process high pyrite ores that were previously considered untreatable, and opened further opportunities for maximising flotation recovery by de-bottlenecking plant regrind and cleaning capacity.CITATION:Hoyle, A, Bennett, D and Walker, P, 2015. The increased recovery project at the Phu Kham copper-gold operation, Laos PDR, in Proceedings MetPlant 2015, pp 246–265 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Gary L. Simmons

Noranda&apos;s Grey Eagle Mine and Mill, located in the Siskiyou Mountains of Northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mining, milling and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1984

By F. Keith Shelton

"INTRODUCTION Cobalt is an essential metal in the normal industrial ac¬tivity of the United States. Being an important constituent of high-speed steels and other cutting-tool materials, it becomes of critically essential importance during periods of national emergency. 3/ The Presidential order of December 20, 1940, included cobalt among other essential commodities that could be exported only under license. The Executive order 4/ listed cobalt metal, cobalt oxide, and alloys containing more than 5 per¬cent cobalt as being within the licensing requirements.There was no domestic marketed production of, cobalt products from 1931 until 1940 when the Pyrites Co. 5/ produced some cobalt oxide. The major portion of the domestic cobalt requirements has been obtained from Northern Rhodesia, the Belgian Congo, and French Morocco. 6/ The uncertainty of sea transportation from those sources of supply demanded that steps be taken to obtain from domestic raw materials an adequate supply of cobalt for use in the materials required for production of indispensable machined war metal products. In connection with the national policy for attaining self-sufficiency of strategic and critical materials, the Bureau of Mines, Boulder City, Nev., Experiment Station initiated studies to recover cobalt from the low-grade oxidized cobalt deposits in the Goodsprings district, Nevada. Hewett 7/ reported occurrence of cobalt specifically in the Blue Jay, Columbia, Copper Chief, and Highline mines and generally over a widespread area in the district."

Jan 1, 1946

By Ross R. Bhappu

Anticipating a major power cost increase in 1990, Cyprus Copper Company decided to modernize the Miami Smelter at a cost of $92.5 million. The modernization project included the addition of an Isasmelt vessel for use as the primary copper smelter and the modification of the existing electric furnace to a slaglmatte separating vessel. The project was completed in June of 1992 and is currently operating at close to its design capacity. This paper provides a summary of the decision making process, a description of the project, a summary of start-up problems and solutions and the current status of the smelter operation.

Jan 1, 1994

By C. S. Simons, G. Major-Marothy, M. A. K. Grice, D. A. Dahlstrom

The vacuum filter operating variables that influence cake moisture are discussed. The influence of temperature control, particularly through application of steam to the cake, is emphasized. Results of pilot plant studies on filtration of fine hematite concentrates are presented and discussed, and are shown to support the theoretically-derived conclusions. Results on fine magnetite concentrates are also used to support the argument. The relative merits of disc and drum filters from the standpoint of cake moisture are discussed. Moisture content has always been recognized as one of the most important properties of concentrates used as pellet plant feed. Most iron ore concentrates are produced by wet methods, and are finally de-watered on filters. Obviously, a real economic advantage accrues to the ability of control the moisture content of the filter cake within the range required for optimum pellet production. Another consideration, also, has been receiving increasing attention recently. Transoceanic shippers of concentrate cargoes are critically assessing the hazards of excess moisture. The nature and magnitude of these risks have been described, &apos; and it appears that their elimination may require that residual moisture be somewhat lower than the limit for proper pelletization. Coarse, very free-filtering materials, such as the products of spirals, are usually best handled on top-feed types of machines. The moisture content of the cake may be held at a specified value by proper design and operation, taking into account cake thickness, air-flow rate, and drainage time. Fine-grained concentrates, with which we will be concerned here, must be filtered on Drum or Agidisc machines. With many of these materials, it is possible, by proper design, to meet cake moisture requirements with a conventional filter station. The first installations to produce high-grade pellets from magnetic taconites fell in this class. In fact, the design criteria were developed in connection with operations of Reserve Mining Co. at Silver Bay, inn.,2 and these have been verified repeatedly in other mills. The trend today, however, is toward the production of more difficultly dewatered concentrates. This is due on the one hand to the increasing attention being given to non-magnetic ores, which tend to be far slimier, and therefore much more retentive of moisture, than the magnetites. On the other hand, the pressure to improve the grade of the magnetic ores is leading to finer grinds, which also are more difficult to dewater. In the latter case, the decision to improve grade in an existing operation by finer grinding for better liberation may lead to two unattractive alternatives: 1) substantially higher bentonite consumption, plus the risk of poorer quality pellets, from high cake moisture, or 2) installation of a thermal dryer. There is, however, a third alternative. In recent papers by two of the authors3,4 it was shown that for many materials a significant decrease in cake moisture can be obtained by applying live steam to the cake face during the drying part of the filter cycle. Further, this limited drying appears to have distinct economic advantages compared to thermal drying. It is the purpose of this paper to explore the third alternative. To do this, the results of an extensive pilot study of steam filtration of a hematite flotation concentrate will be critically examined. This study was sufficiently broad so that a number of alternate suggestions (besides steaming the cake) for reducing moisture content were tested, and comparative data for both Drum and Disc filters were obtained. The work was particularly interesting since the concentrate has a high Blaine surface, and is therefore particularly difficult to dewater to the levels required. FILTER CAKE MOISTURE The significant difference between concentrate filter cake as discharged from the filter, a cargo of that same filter cake during or after shipment, and a green ball formed from that filter cake is in the relative volume of voids, or porosity. In every case, the material is a collection of small solid particles held together by the cohesive forces of a liquid. The physical properties of the aggregate are determined by the

Jan 1, 1967

By Z. Q. Chen, M. H. Loretto, Y. G. Li

"As-cast, As-forged, as-solution-treated, and solution treated and aged microstructures of Ti-15Mo (IMI205) with and without carbon were examined using optical microscopy, scanning electron microscopy .and transmission electron microscopy. Tensile testing was carried out at room temperature. It was found that carbon acts primarily as a titanium carbide former: Titanium carbides increase slightly the tensile strength, but decrease the ductility of IMI205. These observations are interpreted in terms of the titanium carbide morphology observed using SEM and TEM and the phase diagrams of Ti-Mo, Ti-C, and Mo-C.IntroductionIn a recent study on the development of a burn-resistant 13-Ti alloy, carbon was introduced· into the Ti-V-Cr system in order to optimise the mechanical properties. Research results[1, 2] demonstrate that carbon addition can refine the 13 grain size and improve the stability of the 13 phase in Ti-V-Cr alloys. The most attractive result is that carbon addition produced a marked improvement in the ductility of alloys when the carbon content is over 0.1 wt.% in this alloy system. Even after long exposure, the alloy with carbon addition maintains good ductility. One of the main reasons for the ductilising of the alloy is that titanium carbides can getter the oxygen from the 13 matrix.In view of the success of carbon addition in improving the properties and the stability of the Ti-V-Cr alloy, it is of interest to investigate the behaviour of carbon addition in other beta Ti-base alloys. The objective of the present work was, therefore, to assess the microstructures and mechanical properties of IMI 205, a metastable beta titanium alloy, with and without carbon addition using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), wavelength dispersive X-ray (WDX) analysis, room temperature tensile testing."

Jan 1, 2000

By L. Alagha, M. Khodakarami

"This work focuses on the extraction of rare earth metals (REE) from aqueous solutions using stimuli-responsive polymers. Various parameters affecting the adsorption capacity of the polymer, including pH, polymer concentration and REE concentration were studied. The interfacial behavior of REE in aqueous phase before and after polymer addition and the mechanism of the formation of metal-polymer complexes and their properties were investigated using UV/VIS spectroscopy. Results obtained would help to test the feasibility of employing stimuli responsive polymers in pre-concentration of rare earth elements associated with other elements in mineral aqueous streams prior to solvent extraction. The pre-concentration step would reduce the amount of organic solvents used for extraction and striping compared to conventional extraction processes. INTRODUCTION Rare earth elements (REEs) have become the foundation for several technologies and have been used extensively in many industries such as modern electronics, green energy, health care and transportation and defense [1-4]. As these industry sectors are growing, the global consumption of REEs is going to increase dramatically. The current global REEs demand is estimated to be 105,000 tons of rare earth oxides per annum with an expected annual growth of 5.6% [5-6]. Rare earth elements are produced from different sources (primary and secondary). China is considered as the largest producer of REE in the world, providing about 90% of the world’s mine production while the United States is second with 4% of the mine production [7]. High global demand for rare earth materials results in shortage of such materials in the near future. It should be considered that the term ‘‘rare’’ earth is not an accurate term, since they are abundant in some extent in the Earth’s crust, but are typically finely dispersed. Thus, nowadays looking for more efficient and cheaper methods for extraction, separation and purification of low concentrated REE ores and exploring secondary sources are essential. Rare earth materials are found in raw condition and require treatment that involves several processes, which can consume money and time. Recent improvements in extraction and recycling technology have made the extraction of rare earth elements from rare earth sources more feasible in terms of cost and time [8-10]. Physical and pyrometallurgical methods require high-energy and thus high costs. Moreover, due to environmental problems, environmental protection systems are required, and they are not as adaptable as chemical processes [11, 12]."

Jan 1, 2016

"Injection technology has been an important subject from the early days of ladle metallurgy until the present. During the last decade, there have not been many publications in the area of injection technology. It is the author's opinion that with the challenge to find new solutions especially to environmental and energy related problems as well as better understanding of phenomenas from computer modelling, a new era of inventive injection technology developments is at hand. This is illustrated in the article with examples from six different areas where MEFOS is or have recently carried out R&D work related to issues from the injection technology field. IntroductionThe boom in injection technologies came with the introduction of ladle metallurgy treatment during the '70s and '80s. Since then, the theories and principles have been thoroughly laid down by a number of scientists and also published at several early SCANINJECT conferences.Not many new technologies/applications have been presented during the last ten years. This might lead one to believe that everything is known and done. Those, like MEFOS, who are challenged to find technological solutions to a number of environmental problems and energy saving issues in the pyrometallurgical field are, however, continuously faced with the task of developing new injection technologies.Especially, the call for sustainable technologies to solve environmental problems is a challenge for metallurgists all over the world and it will surely induce a revival of injection technologies. So, in order to encourage all injection experts, let us share some new experiences and let us encourage each other's creativity to solve some of the demands of the future society.The following show some examples of technologies under development, or recently tested."

Jan 1, 1996

By F. T. Principe

In order for solvent extraction technology to be acceptable as an alternative to existing jarosite precipitation circuits, iron must be cleanly separated and concentrated into a feed stream suitable for downstream iron by-product recovery which meets market specifications and economics. Ten years ago, significant progress was made in a joint McCill University/CANMET project that involved iron extraction with mono(2-ethylhexyl) phosphoric acid and stripping with HCI. Our iron solvent extraction research was reactivated recently by looking into this and other members of the organophosphorus extractant family. Our research focuses on the mechanisms and control of anion (SO42/CI) transport across the various phases (Rafinate/Organic/Strip), iron build-up in the strip liquor, and extractant stability/selectivity. In this paper, these issues along with some other performance parameters are discussed using data derived from an extensive search of the two commercially available and best known members of the organophosphorus family, di-2-ethylhexyl (D2EHPA) and mono-2-ethylhexyl (M2EHPA) phosphoric acid. Further in this discussion, the challenges lying ahead in the development of sx systems that overcome the deficiencies of D2EHPA and M2EHPA are outlined. In particular, the necessity of considering secondary separation technologies that can further concentrate iron values in the chloride strip liquor to levels economically attractive for the production of saleable iron oxide by pyrohydrolysis is addressed.

Jan 1, 1998

By J. C. Thornley

Service failures of seemingly conventional galvanized bolts, in normal operation, on transmission towers in New Brunswick have been found to be the result of hydrogen cracking. In both these cases, similar failures elsewhere can be avoided by suitable clauses in the purchase specifications. In the first case described, the manufacturing procedure was responsible for strengthening and embrittling a standard, soft, constructional steel. In this case, a fracture mechanics analysis predicted critical crack depths for final fracture very similar to those found in practice. This case reveals an apparent cooperative connection between hydrogen embrittlement and strain ageing in plain carbon steels. In the second case described, the steel was simply a high strength steel which should not have been made into galvanized bolts.

Jan 1, 1979