Search Documents

By Saikat Chatterjee, Xintong (Brett) Liu, Kinnor Chattopadhyay

Magnesia carbon bricks are commonly used in BOFs and are generally pre-heated before the BOF goes into service. Owing to very stringent emission regulations, the BOF pre-heating process need to be controlled and optimized so that, the emission standards are met. One of the major concerns in organic emissions are its stringent limits on emission rates and total volatile emissions. In the present work, an attempt has been made to integrate CFD and Thermodynamic models to predict the emission rate of volatile organics during the pre-heating process. A one dimensional heat transfer model was developed using visual basic and then integrated with thermodynamics calculations using FactSage 6.4. The parameters that affected organic emissions were the pre heating procedure, gas composition of the burner, heating rate and type of the burner. Typical composition of MgO-C bricks and binder materials were obtained from literature and vendor data sheets. Chemical reactions between organic materials, refractory and burner gasses were considered. The model predictions indicated that certain burner conditions could destroy all organics before it exits the vessel while other conditions needed the use of an after burner at the mouth of the vessel. The model was also able to predict the organic emission rates based on the chosen pre-heating profile. This kind of predictive model will be very useful for the steel industry and enable them to justify permit limit applications and stick to the limits by fine tuning their pre-heating process.

Jan 1, 2015

By Mark Laffoon

Gold Fields Operating Co.-Chimney Creek has conducted numerous ore reserve modeling studies In order to optimize the estimates of the gold grades and tonnage distributions. Improved models continue to be produced for the major pits which Increase confidence levels required by Gold Fields management and provide the basis for more accurate long and intermediate term mine planning. Various kriging and non-kriging estimation techniques are used at Gold Fields -Chimney Creek Mine. This paper reviews the modeling histories and, current procedures used to construct these models with particular emphasis on the North Pit deposit.

Jan 1, 1991

By V. A. Chanturiya, T. N. Matveeva, N. K. Gromova, T. A. Ivanova

"The research is aimed at solving the problem of increasing the extraction of gold from refractory ores, which are the main source of growth in gold production in the next decades. The purpose of the research is the development and scientific substantiation of the reagent modes for flotation extracting of gold from refractory ores using eco-friendly low-cost herbal modifiers (HM), providing increase in gold recovery and quality of gold concentrates. In the course of research laboratory techniques for the preparation of experimental samples of HM were developed, which included the sequence of operations of grinding Heraclium leaves and stems grinding, 2-stages extraction at a temperature of 50-60 °C, short-term ultrasonic treatment, filtration and subsequent unification of extracts. According to the developed method, the experimental samples of HM and conducted research were tested to analyze their sorption and flotation activity related to the extraction of gold from refractory gold ores.New data on adsorption and flotation properties of Heraclium stems and leaves extracts (HSE) in selective flotation of Au-sulfide minerals were obtained using UV-spectroscopy, scanning electronic and laser microscopy and atomic force microscopy. The dimensions and shapes of adsorbed hydrophilic films of herbal reagents were identified and mechanism of formation of stable insoluble compounds on the surface of minerals in flotation was explained.Research flotation tests carried out on samples of refractory gold ore of one of Russia deposits showed the possibility of effective use of herbal modifiers to improve qualitative and quantitative indicators of enrichment compared with the standard reagent regime. New reagent modes, using herbal modifiers in an amount of 5 to 10 ml of the extract (300 - 600 g / t, respectively) improves the quality of the concentrate: gold content attains 14.7 g / t, 1.34 times higher than in the baseline experiment and provides a gain of 3.13% extraction.The developed reagent regime with herbal modifiers is the author's original design, patented (patent of the Russian Federation) and have no analogues in the world of mineral processing. (Application number 2015116125 from 04.28.2015, ""The method of flotation separation of sulfide minerals using herbal modifier"", Russia). Actual application of new plant extracts as modifiers in flotation of sulfide minerals is the possibility of replacing of highly toxic chemical compounds by environmentally safe substances of plant origin. Implementation of the developed methods of extracting gold from refractory minerals with herbal modifiers will help to improve gold recovery at 3-5% and the quality concentrate of not less than 1.2 times, leading to higher productivity and a reduction of the negative man-made effects on the environment ."

Jan 1, 2016

By F. Burat

At the present time, methods of mining and coal preparation produce tones of coal fines. The removal of water from these fines is necessary for economical and technological reasons. Supplementary processes that utilize different physical and chemical methods have been developed to in-crease the productivity of mechanical dewatering processes. Researches have shown that chemical reagents used along with conventional systems diminish moisture and increase the capacity and the yields of the dewatering method. In this study, the parameters of the vibrating screen (incline, frequency, feeding rate and screen size), the effects of the application of additional vertical mechanical vibration and surface active reagents (CTAB, SDS, Umectante B-70 and Kerosene) were investigated. At the end of the optimization experiments, 61.0% moisture was decreased to 42.3%. By keeping optimum conditions con-stant, the experiments have been conducted to determine most effective reagent. 41.2% moisture has been obtained with 5 g/t CTAB at the normal pH of the pulp, which were 7.25. By using vibrating screen with combination of the vertical vibrating mechanism, CTAB gave the best result of 40.7% moisture. Finally, the effect of increased surface area of the screen has been investigated and de-creased the moisture level to 38.7%.

Jan 1, 2014

By E. Gaucher, D. C. Gagnon

"The paper refers to methods and concepts used in the computer treatment of banks of geophysical, geochemical and geological data, relating to the exploration of massive sulphides. In particular, a data bank of 400 drill holes on independent conductors can be used to calculate probability levels of intersecting a certain quantity of sulphides according to the characteristics of the conductor. Inversely one can, using the data bank and some cost assumptions, simulate and optimize the cost of intersecting a certain quantity of sulphides by selecting drill targets among conductors according to conductivity, magnetism or gravity. Problems of noise, inherent in any simulation, are illustrated in this paper by the results of a study of the nomenclature of volcanic rocks of 27 drill holes by forty geologists. Compilations of data banks are long and timeconsuming, and it would help to standardize to allow exchange of data. We believe that such efforts may result in the discovery of more mineral deposits and at a lower cost. The present study is supported jointly by SOQUEM The New Jersey Zinc Co. and Cominco Ltd."

Jan 1, 1973

By A. Golpaygan

Application of Computational Fluid Dynamics (CFD) modeling for simulation of fluid flow and combustion in industrial scale electric furnace is presented. Poor combustion efficiency, roof and/or side wall overheating, carry over to off-gas system and non-ideal radiative heat transfer to processes or cooling systems have been common limiting factors causing inadequate process performance of the furnace, operational problems, and safety hazards. This paper describes how CFD analysis can be used to obtain a better understanding of commonly observed problems associated with freeboard combustion. Examples are presented to describe using combustion CFD modeling to understand requirements to diagnose a problem with furnace design including required freeboard volume or possible roof/side wall overheating.

Jan 1, 2011

By Craig S. Compton

The failure of the immediate roof or "roof skin" between installed primary and secundary roof supports causes hundreds of injuries and, on average one or two fatalities each year in U.S. underground coal mines. Conventional roof supports cannot cover enough roof area to adequately control these relatively small, but very dangerous rock falls. The 2006 Mine Safety and Health Administration (MSHA) accident database lists a total of 542 ground fall injuries, including 10 fatalities. An analysis of the database suggests that 434 of the injuries and three of the fatali­ties can be attributed to roof skin falls (See Figure 2). The key to controlling falls of the immediate roof or roof skin is maximizing the area of roof coverage ilnd confining these relatively small loose rocks. Roof screen offers maximum coverage of the immediate roof. Depending on the size and configuration of the screen panels, coverage of up to 100% of the roof area is possi­ble. Screen also offers a first line of defense for machine operators working in the face area by confining or deflecting small rocks that can come loose during mining or roof bolt installation. Figure 1 shows an example of the protection screen provides dur­ing bolt installation. Although the benefits of screen are well-known, mining com­panies in some areas of the U.S., mainly Northern Appalachia and the Illinois basin, are not convinced that roof screen is the best tool for dealing with roof skin control issues. The logistics of material handling, possible ergonomic injuries to workers, and the costs associated with installation are delaying the acceptance of screen as an on-cycle roof support tool. Other mines however, have concluded that installing roof screen can be cost-effective when compared to the cost of lost time accidents, training of replacement workers, or returning to already developed entries for the cleaning and rebolting process.

Jan 1, 2009

By Ting Cheng, Guang-sheng Wei, Ze-shi Yang, Ling-zhi Yang, Yu-feng Guo

The application of the bottom-blowing in the steelmaking process of EAF can effectively shorten the mixing time of the molten bath, accelerate the removal of carbon, phosphorus and sulfur, and improve the production efficiency and product quality. Information about the effects of changing molten steel velocity during the smelting process would help to accurately model molten bath dynamics. In this study, numerical simulation software was employed to simulate the EAF steelmaking process under variable eccentric bottom-blowing gas flow situations. Velocity field data were obtained for the different bottom-blowing schemes. When other nozzles’ bottom-blowing gas flow rates were maintained at 133 L/min, the average velocity of molten steel in EBT (Eccentric Bottom Tapping Area) was increased from 2.8 10−3 to 3.4 10−3 m/s with the eccentric gas flow rate of bottom-blowing from 100 to 267 L/min, the average velocity of molten steel in the bath increased from 4.3 10−3 to 4.6 10−3 m/s with the eccentric gas flow rate of bottom-blowing from 100 to 267 L/min.

Mar 1, 2018

By Kenneth K. Humphreys

Over the past four years, the Coal Research Bureau of West Virginia University has presented a number of papers on operations research in the coal industry before various AIME meetings and meetings of other societies. These papers have been followed up by further presentations in the technical press. The emphasis of all of these papers has been to demonstrate applications of operations research to the solution of numerous types of coal industry problems. In each case, effort has been made to demonstrate that operations research does not require extensive knowledge of computer science or use of sophisticated higher mathematics. In fact, for most applications, satisfactory results can be obtained by a single individual in a minimum of time with no aids other than a pencil and paper and a knowledge of basic arithmetic. The most recent efforts by the Coal Research Bureau have been directed toward the continuing industry problem of optimizing the location of mining facilities. Preliminary work in this area was presented before the Central Appalachian Section of AIME and subsequently published in the May, 1972, issue of Coal Age. This initial presentation illustrated techniques for determining optimum locations of facilities based upon material transport effort under the assumption of constant cost per ton mile of haulage effort. The present paper will expand upon this earlier work and introduce economic factors. In the design of a mine or mining system, careful consideration must be given to the sites selected for each element of the system. Optimum placement of facilities is vital to minimize capital and operating cost. Thus, barring unfavorable geological conditions or other exceptional factors, facilities should be located at those points which represent the minimum cumulative cost over the life of the property. Most cost factors are independent, or essentially independent of the location of fixed facilities. Thus, for example, regardless of the location of the shaft, the direct cost to mine any given ton of coal is essentially constant. The major 1

Jan 1, 1972

By T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate: 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3) Azospirillum had no effect on canopy cover.

Jan 1, 1999

By D. A. Norrgran

The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980's provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focused on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993

By G. Van Weert

In the spring of 2010 double refractory ores from historical stockpiles were processed through Barrick's Goldstrike pressure oxidation facility, thereby providing preg robbing feeds for a variety of metallurgical testwork. This paper describes the effects of amount, type, place and time of addition of activated carbons on CIL gold recovery and shows that native carbon in plant PDX'ed discharge solids can still preg rob gold loaded activated carbon.

Jan 1, 2011

By E. Alldén Öberg

In 2004, LKAB decided to start a basic engineering study in expanding its existing production lines at the Malmberget mine site. It was expected that some of the production lines would become bottlenecks with reference to capacity. In this study, the sorting plant is examined and the results show that several unit operations will be limiting under current operating conditions. An additional purpose with the study was to investigate how replacement of some machines would influence performance and if production plans for the coming years might be achieved. Steady-state simulations using the software Modsim? were extensively used to study process performance for different operating conditions, such as iron content and size distribution in run-of-mine ore. Model parameters were derived from pilot plant data and when possible from ex-isting circuits. A complication for the simulations was the lack of relevant data and therefore some of the initial results were only indicative. The result shows that installation of new screens would give a much better operation, but also new crushers would be an improvement. This, since they can be run with full crusher chamber and tighter CSS. During 2007, most of the proposed remedies were implemented and the result is that the bottle-necks are gone, and the grades and material balances are even better than what was envisioned from the simulations.

Jan 1, 2014

By T. A. de Almeida, M. de Paiva Bueno, M. Powell

The mining industry is one of the foundations of modern society, providing not only the raw materials needed to maintain a contemporary lifestyle, but also serving as a basis for the development of future technologies. From the most basic components of an appliance to the materials needed to design an electric car or a space rocket, each raw material has gone through a painstaking procedure of extraction and processing, and ways to make this process more efficient will be of great help to meet an ever-increasing demand for minerals. One of the biggest challenges when extracting mineral resources is to measure the variability of the mineral body prior to processing. Comminution is the most power-demanding stage, and the lack of geometallurgical testing, often for financial reasons, may result in an inefficient operation. The Geopyörä Rock Breakage test was developed with the objective of making mineral variability data more accessible by providing both standard comminution parameters and rock mechanical properties at low cost, and with a modest sample size, allowing a larger number of samples to be tested to reduce uncertainties and assure productivity. The objective of this paper is to present the results of an extensive validation of this new rock breakage method against two of the main tests currently in use, namely the SMC® and Bond ball mill work index tests. More than 100 samples have been tested and the results compared, showing that the new method can accurately estimate the parameters of the traditional tests. This confirms that the new test is a reliable tool for comminution and geometallurgical tests.

Feb 1, 2023

By Sudhir C. Dhara

An attempt has been made on the concentration of Platinum Group Metals (PGM) from the converter matte material by microbial .leaching. Biological oxidation of base metal sulfides such as iron, copper, nickel and free sulfur present in the matte material using Thiobacillus ferrooxidans is an alternative method to concentrate the PGM-and gold. The method which produces a platinum group metals concentrate is comparable to chemical processes and electrochemical process.

Jan 1, 1995

By A. B., Sabin

THERE are many who know The Lucky Tiger and will remember the 35-mile road from Esqueda, a station on The Nacozari Railroad in northern Sonora, Mexico. They will remember the box canyons of the Agua Caliente Mountains which are scarcely wide enough for two cars to pass; the Bavispe River which one hour may be a lazy trickle and the next a sweeping torrent, and the tortuous road up Tigre and Espuela canyons, now following the wash, now hugging some gigantic red cliff. It is still the same. From camp the view of the distant blue-gray mountains is the same. But one thing a visitor of a former day might miss: The hundreds of pack mules and burros, loaded with concentrates from the mill, which used to take most of the road and show up at the most inopportune places, have almost disappeared, replaced of course by the auto truck.

Jan 1, 1929

By M. M. C Jiménez, D. C. Buzzi, D. C. R. Espinosa, J. A. S Ténorio, G. F. R Oliveira

In this work the extractive and selective capacities of solvent extraction synergistic systems to recover nickel and cobalt were evaluated. The liquor used was from the high pressure acid leaching process (HPAL). Initially the industrial liquor, processed from lateritic ores, was analyzed to identify the concentrations of the metals. Experiments of synergistic solvent extraction were performed later. The extraction liquid-liquid was carried out with a mixture of Cyanex 272 (CY) and Ionquest 290 (IQ) extractants. The process was executed with the temperature of 65 ºC, pH of 5.2 and the ratio aqueousorganic 2:1. Systems of 80% kerosene and CY 20%, CY 16% - IQ 4%, CY 12% - IQ 8%, CY 8% - IQ 16%, CY 4% - IQ 16%, IQ 20% were studied during 20 minutes. The results of this paper showed that the mixture of these two extractants doesn’t improve significantly the recovery of nickel and cobalt from liquor.

Jan 1, 2014

By Rajashekhar Marthi

Lithium is a key component for future electric vehicle batteries and energy storage. The future availability of lithium to meet the growing demands remains in question. Around 60% of lithium resources exist in the form of continental brines. Traditional methods to recover lithium from brines use solar concentration with precipitation and have found limitations in lithium extraction due to interference of Mg in high Mg/Li brines. Thus, there is a need for highly selective adsorbents. Recently, spinel structured delithiated lithium manganese oxides have demonstrated promising results. However, due to the small particle sizes, it is economically difficult to recover the adsorbents and thereby limits industrial applications. In our work, LiMn2O4 ion sieve was synthesized and immobilized on diatomaceous earth. Fundamental adsorption studies were carried out in lithium buffer solutions to understand the nature of adsorption and kinetics. The adsorbents were also tested for recycle stability, as well as recovery of lithium from Great Salt Lake water samples.

By H. Sevim

Placement of coal combustion byproducts into abandoned sections of underground coal mines for the purpose of subsidence mitigation has been investigated in Illinois. Several handling and transportation systems have been examined. Prototype pneumatic and hydraulic placement systems have been developed and demonstrated. The demonstration site, Peabody No. 10 mine in Pawnee Illinois, is selected as a case study. It is found that, for a project of 5 years, transporting 150,000 tons of byproduct annually from a power plant located 32 km (20 miles) to the mine would cost $1.80 per ton and placement into underground would cost $3.07 per ton.

Jan 1, 1998

By Mark Flower

A 20L ignition test chamber has been used to test suspensions of 7 UK and world traded coals in air and O2/CO2 mixtures typical of oxy-combustion conditions. The coals varied in rank from sub-bituminous to bituminous and were tested in varying concentrations from the ignition limit to 400g/m3. Following each successful test the combustion residue was collected, weighed and analysed within a thermogravimetric analyser, allowing Q factors to be estimated. The ignition limit varied slightly in air, but was mostly around the 200g/m3 level. With the exception of Coal C, which was much harder to ignite, it correlated roughly with coal rank. The ignition limit changed significantly with O2 concentration when in mixed O2/CO2 gases. Only a few high volatile coals ignited in 21% O2/CO2 v/v, and then only with a 2500 J, rather than a 1000J, igniter. An increase in O2/CO2 levels to 30 or 35% gave ignition patterns similar to those carried out in air with a further increase to 40% having little additional effect. In addition the minimum ignition concentration decreased with increase in O2. Heterogeneous combustion or gasification of the coal by CO2 appears to be confirmed by comparing weight loss results for air and O2/CO2 mixtures respectively for an equivalent peak pressure rise.

Jan 1, 2009