Search Documents

By M. J. Friedel, D. E. Scott, T. J. Williams

Rock masses in deep level mines are subject to high stresses, which can result in unexpected failure of rock into mined-out openings. Historically, various independent methods have been used to discern the causes of rock bursts and to evaluate stress conditions in rock masses susceptible to violent failure. Personnel from two research centers of the former U.S. Bureau of Mines, Spokane and Twin Cities, investigated a rock burst that occurred in May of 1994 in a rock mass between the 4400 and the 4600 levels of the Sunshine Mine, Kellogg, ID. The team evaluated the current state of stress in the pillar and the most likely cause of the rock burst by studying the seismic history of the pillar, examining the geology, analyzing the available in situ stress data, calculating possible fault-plane solutions for the burst, and performing a seismic velocity tomographic survey. The results of the study showed that post-rock-burst seismicity was concentrated about 15 to 30 m west of and about 15 m above the rock-burst location. The pillar is composed of a very hard sericitic-to- vitreous quartzite of a type rarely found in the mine, but that is often found in other district mines having a history of seismic activity. In situ stress analysis of the pillar and the surrounding rock mass showed a probable stress rotation from northwest-southeast to east-west. Of four fault plane solutions, the most probable was either a left-lateral, strike-slip movement with a compressive principal stress oriented nearly north-south, or a right-lateral, strike-slip movement oriented east-west. Finally, tomographic images showed low-velocity areas (interpreted as areas of low stress) associated with the crosscuts and haulageways, and high-velocity areas (interpreted as areas of high stress) associated with the rock-burst location. High velocities were also found in a planar area oriented in an elongate northeast-southwest direction.

By W. G. Millar

Until a fire occurs, insurance and prevention work are often looked on as unavoidable necessities, but as insurance is back of all business credit, it is essential to know that in case of damage money will be available to cover the loss; while the interruption of production, often caused by a fire, brings home the realization that if prevention work avoids such an interruption, it is well worth while. Fire insurance is a legal contract guaranteeing the payment of large amounts to an owner, but it is possible there is no other important contract that receives so little consideration. Although previously carried on elsewhere, it is only of recent years that insurance engineering has been actively followed up in Canada, with inspections of an owner's property carried out for his benefit. Now inspections of this kind are made, advice on fire prevention and protection work ?is available, reports with recommendations with regard to the above are furnished periodically, and with this method applied the owner receives the broadest possible cover and security at the lowest cost. Rates are set by the underwriters by rating schedules which charge for defects in a building and allow credits for protection and other favourable features . These schedules are based on the past record of loss of mining properties as a class, so that a fire in another mining property indirectly affects you, but the amount paid is reduced in proportion as your property is improved. The writer feels, from personal experience, that there is no industry where fire prevention receives more attention than the mining industry, and it is a pleasure to advise that, due to this co-operation, some reduction in the basis rates for mining risks is now being made by the underwriters.

Jan 1, 1928

"Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor a production blasting in a quarry. The production blast consisted of double-decked explosive loads in 155 mm (6 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsionexplosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and thevibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of micro-cracks along the joint surface as a function of the vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring."

Jan 1, 2017

By B Mohanty, A Siamaki, K Esmaeili

Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor production blasts in a limestone quarry. The production blast consisted of double-decked explosive loads in 125 mm (5 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsion explosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and the vibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of microcracks along the joint surface as a function of the relatively low vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring.

Jan 1, 2017

By J. F. Davis

Pegmatite dykes containing lithium minerals and beryl occur dose to the borders of intrusive masses of granitic rock in the Winnipeg River area of Manitoba. Both vertical and flat-lying dykes are present. Most of the pegmatites consist of zones, containing characteristic mineral assemblages, arranged more or Jess parallel to the borders of the dykes. Five important lithium minerals are present; each occurs in a separate zone, but all the lithium-bearing zones are situated toward the centres of the pegmatites. Spodumene is the most abundant and widespread of the lithium minerals and occurs as small crystals intimately intergrown with quartz. Beryl is not an important constituent of the lithium pegmatites, but when .present, occurs outside the lithium zones, toward the margins of the -dykes. Beryl is most common in dykes containing few or no lithium minerals. The mineral assemblage in the beryl zone of the lithium dykes is the same as that of the beryl dykes. The attitude and internal structure, particularly zoning, of the pegmatite dykes, and the texture and assemblages of the constituent minerals, have an important bearing on exploration, development, and mining of these pegmatites, and on the extraction of various mineral products from them.

Jan 1, 1958

By Y. M. Zhao

Reutilization of waste printed circuit boards (PCB) can not only prevent potential environmental pollution, but also achieve recycling of secondary resources. Study on recycling of discarded PCB belongs to the front edge of environmental pollution prevention and resource recycling. In order to effectively crushing waste PCB, and solve the problem of secondary pollution of fugitive odor and dust during the crushing process, a wet impacting crusher was adopted to achieve comminution liberation of PCB in water medium. 96.79% of the crushed yield was distributed in ?2mm, and metal took 97.18% in this grade of production. Size distribution of PCB particles was characterized double peaks at the sizes of ?1+0.5mm and ?0.074mm. A double Rosin-Rammler function, is called DRR function, is put forward to describe the size distribution of PCB particles. The DRR function of cumulative weight percentage oversize of PCB was non-liner fitted by self-defining DRR function of the Origin 7.0. The evaluation indexes of the fitting results are the correlation coefficients R2 of 0.9994 and residual E of 0.18671, those show that DRR function is perfectly accurate. Based on the research the mechanical separation and material properties of PCB, a wet process of reclaiming metals from PCB using a new style separator ? tapered diameter separation bed (TDSB) in water medium was designed, and the related separation mechanism was studied. The fluid field of the tapered diameter separation equipment was simulated by the Ansys Flotran software, the variation laws of the velocity in each position in the fluid field as well as the equation of axial distribution sectional max velocity were analysed according to the simulation result, the stress change and motion trajectory of the pellet in the certain fluid field were analysed. The results show that the expanding tubular structure of the varied diameter separation bed indicates gradually decreasing velocity of water flow along the axis, assuming a certain angle in the bed, as a result of the gravity?s influence, and there was corresponding change to the distribution of the flow velocity, thus the whole formed a special fluid field where velocity variations exist in different positions. When the material passed through the fluid field along with the water flow, as a result of the difference to the particle density, the granularity and the shape, there would appear the difference to the motion trajectory as well as the movement distance under the action of the fluid: The lower density materials discharge along with water flow, but the higher density materials would be kept in bottom of the bed and discharge through material mouth. Therefore, light and heavy products were separated effectively according to the density. Using tapered diameter separation bed to process the ?1mm size crushed material of waste printed circuit boards, with the discharge of water 5.5m3/h, feed-rate of the material 250g/min and with an obliquity 35°, product with 93.92% in integration efficiency and 93.73% in recovery ratio of the metal were obtained by the primary separation. Compared with other mechanical methods, the range of particle size was broaden using the TDSB to recovery metals from PCB, and lower limit size of separation almost approach to 0. An innovative process of ?wet impact crushing+ classifying+ tapered diameter separation? recycling metals from waste PCB was developed.

Jan 1, 2014

By Rob Thomas

It is generally agreed that standing support should be installed in roadways that will for various reasons, be holed through with a longwall. Considering the magnitude of the associated abutment loading in conjunction with the need to ensure that the material used is cuttable, some form of cementitious support is often used.

By Tristan Worsey, Nathan Rouse, Kyle Hall

Drilling accuracy is the foundation to any successful blast operation. Even the best blasting practices cannot overcome poor drilling and still obtain desired results. Inaccuracies in boreholes can result in flyrock, increased vibration, uneven floor, and other undesired effects. As depth increases, variation in actual burden and spacing is expected even if collars are located precisely. Problems arise when this deviation reaches a point where it adversely affects the function of the blast design. Not only can unsafe conditions such as insufficient burden at the face develop, but poor fragmentation can compound adverse effects. As with any troubleshooting, problems cannot truly be fixed if they cannot be measured. As a result, significant work has been done in the past on this subject. Currently, there are both cheap and expensive methods used to quantify deviation for a given borehole. However, implementation of these techniques is limited. In general production blasts, little is known about the variance in designed versus true borehole geometry. This is especially true if the blaster does not see telltale signs of drilling deviation. However, losses in blast performance may exist and provide an opportunity to obtain better fragmentation and reduce fines. As drill and blast operations strive for better optimization, greater focus is being placed on drilling accuracy and solutions to this problem. The following paper details the use of several current methods for deviation measurement in order to help prevent compromises of safety and improve overall blast performance.

Jan 1, 2018

By ROBERT H. BOOTH

THE happy intra-plant relationships of the Bridgeport Brass Co. are largely attributable to the interest of the management in this important business factor. In furtherance of this development Carl F. Dietz, President of the Company and a member of the Institute, has contributed the novel plan for the objective presentation of business economics, described herein. All of the officers of the corporation are active in its management and they together with many other workers filling both executive and subordinate positions have a substantial financial interest in the enterprise. The viewpoint of this organization is fairly reflected by the following quotation from Roosevelt's "The Foes of Our Own Household."

Jan 1, 1924

By Gary B. Glass

In 1997, 92.3% or 235.7 Mt (259.8 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River coalfield. The mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft). The thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash and 19.98 MJ/kg (8,590 Btu/lb.). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coalbeds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 289 Mm3/a (10.2 billion cu ft/year). This production is occurring west and downdip from the coal mines and is increasing each year.

Jan 1, 1998

By Yoginder Paul Chugh, Jason E. Tinsley

"Over the last five years, the authors have compiled a database of Short Encapsulation Pull Test (SEPT) evaluations from Interior Basin (Basin) coal mines. Typically, SEPT data are analyzed to obtain peak load carrying capacity per unit length of resin encapsulation designated as the ""Grip Factor,"" or GF. In a previous paper, ""An Analysis of Short Encapsulation Bolt Pull Test (SEPT) Data From Interior Basin Coal Mines,"" authors analyzed tangent value of the load-displacement curve as Anchorage Stiffness at 50% (AS-50) of the peak load, or GF value, to assess reinforcement potential of an installed bolt system. This paper attempts to correlate the secant AS VALUES (of SEPT on 6 ft (1.8 m) long installed bolts at a lower load of about four tons from several different mines in the Basin with their MSHA-approved primary support requirements. Since the current regulatory environment requires plan changes dynamically to ensure that roof falls are minimized, the authors hypothesize that the practiced roof control plan must meet the minimum requirement of adequately supporting immediate roof strata. The analyses are based on 181 SEPT studies performed by Minova professionals. Analyses indicate a macrolevel correlation for both roof support density and roof support cost that may have the potential to be used by mine operators to compare their performance with other mines in the area. Limitations of the analyses include ignoring mining depth, mining height and required secondary supports as part of the requirements for a roof control plan. The authors recommend additional analyses to develop this concept further to develop guidelines that can be confidently used by coal companies.INTRODUCTIONPartially- and fully-grouted bolts are extensively used in coal mines for roof support as part of MSHA-approved roof control plans. Since grouted bolts have a larger area of contact with the rock, they can develop much greater anchorage capacity than conventional expansion shell (point-anchored) bolts. Load transfer characteristics and interaction mechanics between steel rebar, grout and rock mass around the bolt hole for grouted bolts are generally assessed in the laboratory or field though short-encapsulation pull tests (SEPT), which have been extensively researched by Aziz and Jalalifar (2005), Aziz (2004a), Serbousek and Signer (1987), Signer (1990), and Mark et al. (2002), among others. In a SEPT, about 12 in. (30 cm) of bolt length is typically encapsulated in resin and a pull test is performed to collect load-displacement data prior to failure and, in some cases, post-failure. A typical load-displacement data set for a bolt is shown in Figure 1. SEPT characteristics are designated by peak load carrying capacity, or grip factor, which is the peak load carrying capacity per unit length of resin encapsulation. SEPT is routinely used to assess anchorage performance characteristics of different lithologies overlying a coal seam to identify type of bolt, bolt diameter, length and spacing across and along an excavation. Anchorage stiffness, or AS, at any load may also be calculated as the tangent or secant value of the slope of the load displacement curve at a particular load level. Anchorage Stiffness characteristics of bolts from SEPT data have typically not been considered in any depth until recently (Chugh et al., 2014; Chugh et al., 2015)."

Jan 1, 2016

By Kostas Kaklis, Zach Agioutantis, Robin Flattery

Pillars are used as the primary support structures for underground mining to maintain stability by supporting the over laying strata. In the case of horizontal seams, the pillars are typically subjected to axial loading due to the weight of the overburden and/or abutment stresses, while in the case of inclined seams they are subjected to oblique loading due to both the vertical and horizontal in-situ stress.

By Ludwig Schmidt

The petroleum industry has recently shown sucks great interest in the evaporation of crude oil and of gasoline, and in the prevention of evaporation losses that almost daily there is being developed and placed on the market equipment designed especially to reduce these losses. Among the recent developments is a new type of tank roof known as the "floating roof," which practically eliminates the vapor space over the surface of the oil, thus removing one of the chief causes of evaporation. There are at the present writing at least two types of floating roofs which, while similar in fundamental principle, differ mainly in the method of making contact with the inside shell of the tank. One type of floating roof is known as a floating tank deck, and has on its circumference flexible metal baskets containing gravel that .rest against the inside shell of the tank. In the other type of floating roof contact with the tank shell is made by the use of movable buffers or shoes. These are attached to the outer ring of the roof and are pressed against the tank shell by means of springs.

Jan 1, 1923

By Nicolin Govender, Pramod Kumar, Raj Rajamani

Mill power models have been used in a variety of ways in industrial practice since power directly equates to throughput and fineness of ground product. We first start with Hogg-Fuerstenau Power Model and show how this model successfully predicted the power draw of many grinding mills in several mining operations. Then, we show how this model was on the verge of being able to predict the influence of lifter design on power draw. Next, we describe the discrete element model and how it overcame the issues faced by the previous power model. Using a DEM software known as Millsoft, we show the influence of lifter design geometry on power draw and analyze the power draw of rubber lifters versus the steel lifters via several case studies. As years passed, the two-dimensional discrete element model imbedded in Millsoft is superseded by three-dimensional discrete element method. Due to the gigantic computational power of graphic processing units, new computational codes that can do the tumbling motion along the entire length of the mill has come about. Here, we show the predictive capability of Blaze-DEM for ball and SAG mills.

By R. Schuerch, C. Cimiotti, M. Piemontese, N. Karlin, P. Perazzelli, P. Halton

The new Los Angeles, California JWPCP effluent outfall tunnel will transport secondary-treated effluent from the Joint Water Pollution Control Plant in Carson to White Point Manifold. The tunnel will be approximately 7 miles (11 km) long with a finished internal diameter of 18 ft (5.5 m). The TBM is designed to cope with high water pressure up to 10 bar. The geotechnical challenges are due to the heterogeneous subsurface conditions: in the first half of the alignment, the tunnel runs through soils with a low overburden under urban areas, and, in the second half, the tunnel runs through extremely weak, intensely faulted rock masses with high overburden. Following an overview of the project, this paper focuses on the northern portion of the alignment and presents a decision-making procedure developed during pre-excavation phase in order to cope with the expected heterogeneous conditions during mining. The risk assessment and the TBM operational design of the southern portion will be dealt with in a future paper.

Jun 13, 2023

By Ashish Ranjan Kumar, Steven Schafrik, Oscar Velasquez

Flooded-bed dust scrubbers installed on continuous miners use fibrous type multi-layered filters to capture dust from the airstream. Prolonged operations of the scrubber could lead to filter clogging due to dust accumulation. This results in reduced flow through the scrubber and elevated dust levels in the mine environment. This paper compares the performance of a conventional fibrous screen filter and a novel impingement type dust filter. The impingement filter is a self-cleaning system and was designed to have a resistance similar to the fibrous filter. The cleaning efficiencies for these filters were computed using iso-kinetic sampling and optical counting of coal dust particles in a clean unclogged state. The cleaning efficiency of the impingement filter also increased with an increase in particle size and was comparable with the conventional fibrous filter. The cleaning efficiency of the fibrous filter improved significantly with an increase in water flow. The non-clogging nature of the impingement filter and minimal maintenance requirement makes it an attractive alternative to the conventional fibrous type filter in mining applications. The research also proposes a term called ‘filter performance factor’ to compare the performance of different filters under similar operating conditions.

Sep 19, 2020

Slope stability is a fundamental part of a successful mining operation. It impacts directly on the safety of personnel and the economics of the mine. The Jwaneng Mine in Botswana is planning a push back of 644m depth in the south east wall. Mining will commence in 2010 and be completed in 2024. This will put the mine in the deep pit category. The mine has invested in extensive geotechnical data gathering and design programs that started as far back as 2003 for the south east wall. The south east wail of Jwaneng Mine is characterized by foliation that dips adversely into the mining faces. The orienta1ion of the foliation is variable due to intense tectonic movements that have also caused the occurrence of faults that are sub-vertical. A considerable amount of information on the characteristics of structural patterns and the rock mass has been collected. This paper presents an overview of the feasibility level geotechnical design that is about to be concluded.

Jan 1, 2010

By S S. Kanchibotla, S Morrell

In recent years there has been a growing recognition of the impact that mining practices have on the efficiency of mineral processing operations. Head grade, dilution, particle size distribution and their variability are known to have a significant effect on the throughput and recovery achieved in mineral processing plants. Improved process monitoring and modelling have provided the opportunity to identify and quantify some of these impacts and to define very significant incentives to optimise the overall operation from the mining face through subsequent comminution and processing. The Julius Kruttschnitt Mineral Research Centre has been undertaking research to optimise æMine to MillÆ performance through a major AMIRA research project and through individual research contracts with mining companies. This work has resulted in a broad range of field and laboratory experience in terms of both the challenges and the opportunities encountered when tailoring blasting operations to suit the overall æMine to MillÆ production chain. This paper describes the objectives of æMine to MillÆ blasting to optimise the system of rock breakage involved in the blasting, crushing and SAG milling of hard, brittle ores. The design of such blasts falls outside the conventional envelope of experience for most engineers and requires the consideration of some critical factors if the objectives of such blast are to be met and some of the potential problems are to be avoided. Experience to-date has also found that the quality of implementation is critical to the success of æMine to MillÆ blasts.

Jan 1, 1999

By S Wilkinson, S Black, L van den Berg

"The mine ventilation system plays an important role in mitigating human exposure to diesel particulate emissions (DPM), exhaust gases and heat in underground mines. The mine’s secondary ventilation systems are critical for diluting contaminants when working at the face of a heading. To improve these systems it is important to understand and visualise the localised air flow profiles. We have considered an approach that includes both tracer gas measurement–modelling to analyse this complex flow behaviour in a heading. The use of tracer gas enables reliable measurements of flow behaviour and differentiation between the contributions of various contaminant sources including DPM. A pilot study was conducted to demonstrate how tracer gas can be used to directly measure the effectiveness of ventilation dilution in a heading during shotcrete activity. This activity is considered to be one of the more challenging areas for diesel exhaust exposure management. Exposure sources include the diesel engine of the spraying equipment (Spraymech) and concrete agitator truck (Agi) that supplies the shotcrete. During operation both the Spraymech and Agi operators are located outside the equipment’s air-conditioned cabins and both are exposed to diesel exhaust. In the pilot study tracer gas was injected directly into the Spraymech exhaust stream. This allowed thorough mixing, ensuring the tracer gas was able to track exhaust gases and particulates released to the heading. The release was repeated at three different headings with varying degrees of secondary ventilation controls. The study showed that small changes to the secondary ventilation system can significantly impact the contaminant concentration. It also demonstrated that tracer gas can be used to isolate different contaminant sources. The intent is to use this technique in a more comprehensive study to develop best practice guidelines for secondary ventilation installations. This paper presents the technique used and the preliminary results from the pilot study. CITATION: Wilkinson, S, van den Berg, L and Black, S, 2015. Application of tracer gas flow profiling to improve secondary ventilation practice – a pilot study, in Proceedings The Australian Mine Ventilation Conference, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By Michael J. Mujadin

Since the late 60's, planners at American Natural have known that natural gas supplies from traditional sources will be insufficient to maintain a consistently high level of service in the near future. This dwindling of traditional gas reserves will force American Natural and other gas companies to seek new and more exotic sources of supply. In recent years a number of alternative supply sources were considered, including arctic gas, LNG, and SNG based on naptha, LPG and coal feedstocks. Several combinations, all of which included SNG from coal were selected as the most suitable alternative sources of gas supply for American Natural, and thus our company embarked on the formation of a coal gasification project in the early 70's. Work began with the evaluation of available coal supplies in the United States in late 1970. Western North Dakota was selected for several reasons: large contiguous reserves of lignite were available near the surface, similar to German brown coal for which the Lurgi gasification process was originally developed; the conditions for land reclamation in the area are favorable; and the people in the area have a positive attitude toward well ordered development.

Jan 1, 1977