Search Documents

By O van Baalen

The Ernest Henry Mine is a copper-gold open pit operation situated in northwest Queensland, Australia. It is owned and operated by Xstrata Copper, with a current throughput of 11 Mtpa, however, open pit operations are scheduled to cease in mid 2011. The deposit dips approximately 45º and extends for at least another 400 m vertically below the final 530 m deep pit design.Construction and development of a sublevel caving (SLC) operation beneath the open pit was approved in December 2009. The feasibility design requires 39 km of development to be completed prior to production, which will commence in the fourth quarter of 2011. Initial ore production will be trucked and will increase to 3 Mtpa by the end of 2012, after which a hoisting shaft will be used. Ore production will then increase to 5 Mtpa in 2013 and ultimately to 6 Mtpa in 2016.Two 3000 kilo watt of refrigeration (kW(R)) modular refrigeration plants will be installed, as well as two 1600 kW mixed-flow fans capable of a combined flow rate of 780 m3/s at a total pressure loss across the mine of 2000 Pa. The main fans will be installed underground and will exhaust into the base of the pit.The following challenges were faced in the development of the ventilation and refrigeration network:•a relatively steep geothermal gradient,•tropical ambient conditions,•working under a wide pit shell, and•a large underground trucking fleet prior to shaft commissioning.A considerable number of ventilation studies were conducted with later studies extensively using Ventsim Visual™ mine ventilation software to complete the design process of the ventilation and refrigeration networks, including the comparison of several alternative designs. The paper focuses on design challenges prior to the commissioning of the hoisting shaft, and discusses resistance optimisation and occupational hygiene-related design parameters, such as heat and diesel emissions, production level ventilation, main fan selection and location, and refrigeration requirements.

Mar 21, 2011

By J. H. Baek, D. W. Lee, B. K. Kim

Nanostructured Cu-Al203 composite powders were synthesized by thermochemical process for an electrode application. The synthesis procedures are 1) preparation of precursor powder by spray drying of solution made from copper and aluminum nitrates, 2) heat treatments to evaporate volatile components in the precursor powder and synthesis of nanostructured CuO+Al2O3, and 3) CuO reduction by hydrogen into Cu. The suggested procedures stimulated the formation of the gamma-Al2O3. The mean particle size of the final composite powders was 20nm, and the electrical conductivity and hardness in the hot-extruded bulk were competitive with Cu/Al2O3 composite by the conventional internal oxidation process.

Jan 1, 2004

By Shawn Orser, Jennifer Waddell, Mike Sierakowski, Tom Barrett

Production evaluations were conducted at Daisy Gold Mine (Glamis Gold, formerly Rayrock), between August, 1997 and August, 1998 to quantify the effect of 3M fluorochemical surfactants (fluorosurfactants) on extraction kinetics and gold recovery in gold heap leach mining operations. Ore was treated at a level of 7-10 grams surfactant per ton of ore using 3M Pluorad TM Leach Mining Additive PC-GOLD. Kinetics and gold recovery were determined by solution assay for each of the tests. Both tests indicated improved kinetics, and data from Test 2 was used for determination of a quantitative increase in gold recovery resulting from PC-GOLD addition. A discussion of test results including methods used to determine gold recovery is provided.

Jan 1, 2000

By Daniel Hauer

In considering the cost of rock excavation, but little attention has been given to the economical handling and breaking up of boulders. Very few records seem to have been kept as to the cost of such work, and although it is difficult for this reason, to set a fair price for breaking up and handling boulders of various sizes, yet the cost of this detail work enters very materially into the cost of solid rock excavation. The subject is worthy of close and prolonged study.

Jan 1, 2006

By Price B. D, Staunton W. P

The Mineral Science Laboratory of the Government Chemical Laboratories has recently investigated various procedures for the analysis of the platinum group metals (PGMs). This investigation covered a number of methods for the extraction and preconcentration'of the PGMs from a wide range of geological materials. The nickel sulphide extraction technique proved to be overall the most applicable procedure. Flame atomic absorption spectroscopy (FAAS), electrothermal atomisation atomic absorption spectroscopy (ETA-AAS), inductively coupled plasma atomic emission spectroscopy (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS) were examined for their suitability in analysing platinum group metals in solution. ETA-AAS and ICP-MS proved to be the instruments of choice due to their low detection limits.

Jan 1, 1987

By M. Timucin

High-temperature phase relations and thermodynamics of the condensed phase region of the Pb-S-O system at 1473 K were analysed by use of the available information. The sub-regular solution models on Pb-PbS and PbO-PbSO4 continuous melts were used in conjunction to generate a consistent set of thermodynamic and phase equilibrium conditions for the Pb-S-O system. The directions and distributions of conjugation lines between melts of this system were derived with relevant activity and composition data. The calculations permitted the thermodynamic analysis of direct lead smelting and the construction of isothermal reaction diagrams for the system in terms of oxygen and sulphur partial pressures at 1473 K.

Jan 1, 1989

Environmental and amenity factors have introduced a new dimension to the technical problems of the mining industry in finding, extracting and processing the mineral and energy products on which we all depend. Intervention by outside regulatory bodies is restricting the production of minerals and denying the industry access to large areas in which the orebodies of the future may occur. The solution lies to a large extent within the industry itself and appropriate management techniques are necessary to ensure that exploration and mining are seen as an acceptable as well as a necessary land use. Close liaison between operators and the responsible authority is necessary to achieve these objectives and to make the best use of our land resources.

Jan 1, 1979

Expert systems have been employed in a number of areas for a considerable number of years. However, the traditional long development times associated with these systems have restricted their application. With the advent of powerful Expert System Development Tools such as COMDALE/X and the use of efficient development techniques, the time required can be drastically reduced. This results in the availability and applicability of this technology to a wide range of applications. This paper discusses some of the 'rules' which indicate amenability (or otherwise) of a particular problem to an expert system solution. Various problem types are examined and these are illustrated with reference to examples of their use at various operating sites.

Jan 1, 1991

By H El-Shall, R Stana a

An innovative process for the separation of carbonaceous minerals from bulk ores is presented. In this process, the surface of carbonate minerals is reacted with acid used to nucleate CO2 bubbles at the particle solution interface. Entraining the liberated CO2 gas at the surface via coating agent renders the particle more buoyant providing for a selective separation from non-carbonate containing masses. Different surfactants were tested to stabilise the bubbles and float the particles. In this paper, separation of dolomite from apatite using PVA (polyvinyl alcohol) as a coating agent, is discussed. Interestingly, up to 10 mm particle sizes can be floated. Moreover, flotation of a phosphate and dolomite mixture was carried out and MgO content

Jan 1, 2005

By Randall D. Peterson

Economic operation of a mine ventilation system must include some means by which operating costs can be quantified and evaluated periodically. Current practice at most mines relies upon the best judgement of foremen, engineers and managers to identify high cost or problem areas in the system and to estimate potential costs and benefits of work proposed to reduce inefficiencies. The problem with this is that significant savings can be overlooked or sub-economic projects may be undertaken when sufficient attention is not paid to the interrelationship between airflow characteristics and corporate financial criteria. In order to accurately determine costs and benefits it is necessary to view the solution of each potential ventilation problem as a separate economic opportunity.

Jan 1, 1993

By Z. S. Shao, X. Z. Li

"Sub-critical crack growth plays an important role in long-term creep failure in brittle rock. Based on micromechanics established by using relationship between micromechanical wing crack growth model and macroscopic strain, and comparing theoretical model with testing results, a method, which applies the theory to real rock, is suggested in this paper. Using this method, properties of creep, damage and progressive failure in brittle rock are investigated. Effects of stress state on creep failure time and steady-state creep rate are analyzed and graphically presented. The results are helpful to support structure design and service life evaluation of underground structures with high geostatic stresses. INTRODUCTIONDuring the long-term operation in underground space with brittle surrounding rock, due to chemical action between pore water and rock, the failure of rock often occurs at stresses below its short-term failure strength, which brings serious effect on the long-term stability of underground structure. Thus, the long-term strength of brittle rock attracted wide interests of scholars around the world. The static fatigue limit was predicted by exponential function that is derived from abundant experiment data of stress level and failure time(Schmidtke & Lajtai, 1985), and similar result by relationship between stress state and failure time was also suggested (Lau & Chandler, 2004; Aubertin et al., 2000; Sangha & Dhir, 1972). According to relationship between steady creep rate and stress state during creep, a critical stress that transforms steady-state creep to accelerated creep was studied and the long-term strength was suggested (Tsai et al., 2008; Ma & Daemen, 2006; Lajtai et al., 1991). Based on the results of experiment in compression, the long-term strength of rock was defined by stress at volume strain reversal. When applied stresses are larger than the long-term strength, the microcracks in the rock will grow constantly, damage of rock will increase and failure of rock will occur finally (Chandler, 2013; Bieniawski, 1967; Brace et al., 1966)."

Jan 1, 2015

By W. R. Marks

Computer-aided torsional analysis of grinding mill drives is defined and related to the mill design process. Equations of torsional dynamics are developed for general mechanical drives. Consideration is given three solution types - specifically the determination of undamped natural frequencies, the calculation of steady vibration amplitudes, and the prediction of transient torques during starting. Following a summary of the methods of calculating drive motor performance, the problem in making practical application of this theory are discussed. Experiences in both calculating and measuring the torsional loads on a large ball mill with dual synchronous motors are reviewed. Conclusions are drawn on the effectiveness of computer-aided torsional analysis for improving mill drive reliability.

Jan 1, 1984

By Muhammad O. Rahim

The importance of planning ventilation systems in modern coal mines cannot be overemphasized. Interconnected entries, airflows around and through mined-out areas, leakages through stoppings and other control devices, and the use of multiple fans all contribute to the complexity of ventilation network analysis. Fortunately, the availability of computer programs (e. g., Didyk et al., 1978; McPherson, 1966; Wang and Saperstein, 1970) has greatly reduced the difficulty in net- work analysis. However, to obtain a suitable solution to the practical problem, a ventilation engineer has to simulate various conditions based on the proposed ventilation layouts and the capacities of available fans. It is often a trial-and-error process, although engineering knowledge and judgement are required.

Jan 1, 1982

By Albinson T

Mexican epithermal deposits can be broadly grouped into two types based on their contained metals, distribution, associated igneous rocks and fluid inclusion compositions. Silver-gold deposits (e.g. Tayoltita) mostly occur in the western part of northern Mexico where host rocks consist of Eocene, intermediate composition volcanic and intrusive rocks; fluid inclusion studies indicate that mineralizing fluids were _10 eq. wt. % NaCl). The distribution of these two deposit types, crosscutting major major crustal sutures, and the close spatial-temporal relationships between mineralization and magmatism, together suggest that magmatic processes were more important in the formation of mineralizing solutions, as a source of both ligands and metals, than the segments of crust hosting deposits.

Jan 1, 1995

By A. E. Hilder

Introductory The following pages present the results of field investigations, laboratory and commercial tests, drilling, surveying, and preliminary development of the refractory clays which have been discovered recently in the township of Kipling, at the foot of Long rapids on the west side of the Mattagami river about 57 miles north of Kapuskasing and approximately 7 miles north of Smoky Falls, the terminus of the privately owned railway operated by the Spruce Falls Power and Paper Company, Kapuskasing (see Figure 1). Investigations on the clays of northern Ontario have been carried on over a period of seven years by officers of the Ontario Department of Mines, and I am indebted to the information published by that Department in reports by W. S. Dyer and A. R. Crozier, as well as?by Professor R. J. Montgomery, of the Ceramic Department, University of Toronto. It was, in large measure, the data given in the 37th, 38th, and 42nd Annual Reports of the Ontario Department of Mines that led me to make a personal investigation of the Mattagami River clays, with the result that we now have a commercial undertaking that will develop eventually into an industry of considerable importance in supplying the central manufacturing districts of Canada with refractories that heretofore have been largely imported from the United States. An extract from the 42nd Annual Report of the Department, Part III, 1933, page 75, reads as follows: "As for the refractory clay, the deposits are undoubtedly very large, but what is urgently needed is a deposit near the railway under sufficiently shallow overburden for recovery by stripping'. Having previously made an investigation of the clays adjacent to the Temiskaming and Northern Ontario railway, and these clays proving unsuitable, I turned my attention to the outcrops of refractory clays on the Mattagami river, first reported by Keele in 1919. This area offered possibilities within the economically permissible distance from rail transportation.

Jan 1, 1935

By A. A. de Gast, R. B. James

"The metal content of ore blocks can be calculated by the use of many different methods. These methods range in sophistication from manual calculation to computer. oriented techniques. In this case a cubic polynomial regression model is developed to depict the grade distribution of an orebody. Mine production, in stope dimensions, is then simulated on a computer to predict the output of metal content. The volume, grade and variance of the grade are estimated by triple integration and matrix algebra. A case study shows reasonable agreement between the results from the mathematical model and the mine geologists' estimate of production and ore reserve grade and tonnage."

Jan 1, 1972

By Milka Madahana, John Ekoru

For efficient management of operations, mining companies are required to be able to predict potential scenarios for main market factors. Competitive advantage and value creation are established through managing the value chain well. The mining value chain is usually faced with challenges from various shifts in commodity markets as well as ongoing uncertainties. Therefore, there is a need for accurate analysis of data from the markets, for the prediction of commodities, for instance, Precious Group Metals (PGM). The main objective of this research work is to apply machine learning methodologies with the aim to identify patterns and trends in the Precious Group Metals, and thereafter analyze and predict the future trends of these markets. Numerous machine learning models are applied to a dataset consisting of 15 years of daily price for eight precious metals namely Platinum, Palladium, Rhodium, Ruthenium, Osmium, Indium, Silver, and Gold. The results reveal the patterns and trends within the data sets and that different machine learning methods could be suited for the prediction of market prices for each of the PGMs. The application of an amalgamation of various machine learning methods may result in more accurate predictions of the PGM markets. Accurate prediction of market prices for PGMs will possibly result in unlocking untapped sources of value in the mining industry.

Jun 25, 2023

By Robert L. Opila

Negative electrodes for alkaline nickel-metal hydride batteries composed of MmNi3.5Al0.8Co0.7, where Mm is misch metal, have been characterized electrochermically and using x-ray photoelectron spectroscopy. The stability and rapid hydriding and dehydriding kinetics of the alloy in KOH are attibuted to a surface film. The protective surface film is shown to consist of an porous, outer hydrated layer and a dense, inner oxide layer. In addition, metallic nickel and cobalt are found throughout the film, and are presumed to form a conductive, percolative network that permits rapid electron transfer from the bulk to the solution, allowing rapid electrochemical formation of atomic hydrogen.

Jan 1, 1997

By Richard E. Steffens

The underground portion of Duke Power Company's Bad Creek Pumped Storage Project in northwestern South Carolina consists of a powerhouse cavern (132 m. long, 23 m. wide, 50 m. high), 407 meters of shafts and approximately 3615 meters of tunnel, both lined and unlined, with diameters varying from 4.2 meters to 9.0 meters. A case history is presented, including the early pilot tunnel exploratory work and how this affected design, the design of the project, and the excavation, rock support and tunnel lining work. Problems and experiences encountered during the construction are given. The effects of high horizontal insitu stresses in the granitic gneiss are discussed along with solution taken.

Jan 1, 1989

By P. Mousset-Jones, F. Calizaya

This paper explains and discusses a computer program that has been developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The resulting network problems are solved analytically. With this program, the size of fans can be determined in order to reduce the total leakage and minimize the flow recirculation. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain Project, Nevada.

Jan 1, 1995